Falcon CDL110DFCY-CHLPG, CDL110DFBL-CHLPG, CDL110DFBL-CH, CDL110DFBL-BR, CDL110DFCR-CH Installation and Operation Guide

...

Download

Page 1

USER GUIDE &

INSTALLATION INSTRUCTIONS

Classic Deluxe 110cm Dual Fuel

Australia

U110289-01A

Page 2

Contents

1. Before You Start... 1

Installation and Maintenance 1 Peculiar Smells 1 If You Smell Gas 1 Ventilation 1 Personal Safety 1 Cooker Care 2 Cleaning 2

2. Cooker Overview 3

Hotplate Burners 3 Wok Burner 4 The Wok Cradle 4 The Ceramic Hotplate 5 The Griddle 6 The Glide-out Grill 7 The Ovens 8 The Clock 11 Accessories 13 Oven Lights 14 Storage 14

3. Cooking Tips 15

Tips on Cooking with the Timer 15 General Oven Tips 15

4. Cooking Table 16

5. Cleaning Your Cooker 17

Essential Information 17 Hotplate Burners 17 Ceramic Hotplate 18 Grill 19 Control Panel and Doors 20 Ovens 20 Cleaning Table 21

6. Troubleshooting 22

7. Installation 24

Service and Spares 24 Dear Installer 25 Provision of Ventilation 25 Location of Cooker 25 Conversion 25 Location of Cooker 26 Conversion 26 Positioning the Cooker 27 Moving the Cooker 27 Fitting the Stability Bracket and Chain 28 Repositioning the Cooker Following

Connection Conversion to Another Gas 29 Fitting the Handles and Handrail 29 Levelling 29 Gas Connection 30 Pressure Testing 30 Electrical Connection 31 Final Checks 32 Final Fitting 32 Customer Care 32

8. Conversion to LP Gas 33

Injectors 33 Tap Adjustment 33 Set the Governor 34 Pressure Testing 34 Ax Label 34

9. Servicing 35

10. Circuit Diagram 42

11. Technical Data 43

Classic Deluxe 110 DF (Australia) U110289-01A

Page 3

1. Before You Start...

Thank you for buying a Falcon cooker. It should give you many years of trouble-free cooking if installed and operated correctly. It is important that you read this section before you start, particularly if you have not used a dual fuel cooker before.

This appliance is designed for domestic cooking



only. Using it for any other purpose could invalidate any warranty or liability claim. In particular, the oven should NOT be used for heating the kitchen – besides invalidating claims this wastes fuel and may overheat the control knobs.

Certain types of vinyl or laminate kitchen furniture



are particularly prone to heat damage and discolouration. We cannot accept responsibility for damage caused by normal use of the cooker to any material that de-laminates or discolours at temperatures less than 70 °C above room temperature (as measured by EN30 / EN60335).

Installation and Maintenance

The installation must be in accordance with the relevant instructions in this booklet, with the relevant national and local regulations, and with the local gas and electricity supply companies’ requirements.

Make sure that the gas supply is turned on and that the cooker is wired in and switched on (the cooker needs electricity).

Set the clock to make sure that the oven is functional – see the relevant section in this manual.

The cooker should be serviced only by a qualied service engineer, and only approved spare parts should be used.

Always allow the cooker to cool and then switch it o at the mains before cleaning or carrying out any maintenance work, unless specied otherwise in this guide.

Peculiar Smells

When you rst use your cooker it may give o an odour. This should stop after use.

Before using for the rst time, make sure that all packing materials have been removed and then, to dispel manufacturing odours, turn the ovens to 200 °C and run for at least an hour.

Make sure the room is well ventilated to the outside air (see ‘Ventilation’ below). People with respiratory or allergy problems should vacate the area for this brief period.

If You Smell Gas

• DO NOT turn electric switches on or off

• DO NOT smoke

• DO NOT use naked flames

• DO turn off the gas at the meter or cylinder

• DO open doors and windows to get rid of the gas

• DO keep people away from the area affected

• Call your gas supplier

Ventilation

The use of a gas cooking appliance results in the production of heat and moisture in the room in which it is installed. Therefore, make sure that the kitchen is well ventilated: keep natural ventilation holes open or install a powered cooker hood that vents outside. If you have several burners on, or use the cooker for a long time, open a window or turn on an extractor fan.

Personal Safety

DO NOT modify this appliance.



This appliance can be used by children aged from 8



years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.

WARNING: The appliance and its accessible parts



become hot during use and will retain heat even after you have stopped cooking. Care should be taken to avoid touching heating elements. Children less than 8 years of age shall be kept away unless continuously supervised.

DO NOT use a steam cleaner on your cooker.



CAUTION: A long term cooking process has to be



supervised from time to time. A short term cooking process has to be supervised continuously.

Danger of re: DO NOT store items on the cooking



surfaces.

To avoid overheating, DO NOT install the cooker



behind a decorative door.

Accessible parts will become hot during use and will



retain heat even after you have stopped cooking. Keep babies and children away from the cooker and never wear loose-tting or hanging clothes when using the appliance.

Always be certain that the controls are in the OFF



position when the oven is not in use, and before attempting to clean the cooker.

Page 4

When the oven is on, DO NOT leave the oven door



open for longer than necessary – otherwise, the control knobs may become very hot.

Cooking high moisture content foods can create a ‘steam burst’ when the oven door is opened. When opening the oven stand well back and allow any steam to disperse.

DO NOT drop or rest objects on the door glass.



Although the glass is very strong, a sharp blow or a falling object might cause the glass surface to crack or break.

DO NOT use harsh abrasive cleaners or sharp metal



scrapers to clean the oven door glass since they can

scratch the surface, which may result in shattering of the glass.

Always keep combustible materials, e.g. curtains,



and ammable liquids a safe distance away from your cooker.

DO NOT store ammable materials in the storage



tray or in the vicinity of this unit

DO NOT spray aerosols in the vicinity of the cooker



while it is on.

Use dry oven gloves when applicable – using damp gloves might result in steam burns when you touch a hot surface. Do not use a towel or other bulky cloth in place of a glove – it might catch re if brought into contact with a hot surface.

NEVER operate the cooker with wet hands.



DO NOT use aluminium foil to cover shelves, linings



or the oven roof.

DO NOT use hotplate protectors, foil or hotplate



covers of any description. These may aect the safe use of your hotplate burners and are potentially hazardous to health.

NEVER heat unopened food containers. Pressure



build up may make the containers burst and cause injury.

DO NOT use unstable saucepans. Always make sure



that you position the handles away from the edge of the hotplate.

DO NOT use cooking vessels on the hotplate that



overlap the edges.

ArtNo.324-0001 Steam burst

NEVER leave a chip pan unattended. Always heat fat



slowly, and watch as it heats. Deep fry pans should be only one third full of fat. Filling the pan too full of fat can cause spill over when food is added. If you use a combination of oils or fats in frying, stir them together before heating, or as the fats melt.

Foods for frying should be as dry as possible. Frost on frozen foods or moisture on fresh foods can cause hot fat to bubble up and over the sides of the pan.

Carefully watch for spills or overheating of foods when frying at high or medium high temperatures. Never try to move a pan of hot fat, especially a deep fat fryer. Wait until the fat is cool.

Do not use the top of the ue (the slot along the back of the cooker) for warming plates, dishes, drying tea towels or softening butter.

DO NOT use water on grease res and never pick up a aming pan. Turn the controls o and then smother a aming pan on a surface unit by covering the pan completely with a well tting lid or baking tray. If available, use a multi-purpose dry chemical or foam-type re extinguisher.

Take care that no water seeps into the appliance.



In normal use, the cooling fan will operate when the



oven or grill are in use. Should a fault occur with the fan switch o the cooker immediately and contact your installer or service.

Only certain types of glass, glass-ceramic, earthenware or other glazed containers are suitable for hotplate cooking; others may break because of the sudden change in temperature.

This appliance is heavy so take care when moving it.



The appliance is not intended to be operated by



means of external timer or separated remote-control system.

Cooker Care

As steam can condense to water droplets on the cool outer trim of the oven, it may be necessary during cooking to wipe away any moisture with a soft cloth. This will also help to prevent soiling and discolouration of the oven exterior by cooking vapours.

Cleaning

In the interests of hygiene and safety, the cooker should be kept clean at all times as a build up in fats and other food stu could result in a re.

Never leave the hotplate unattended at high heat settings. Pans boiling over can cause smoking, and greasy spills may catch on re. Use a deep fat thermometer whenever possible to prevent fat overheating beyond the smoking point.

WARNING! Unattended cooking on a hob with fat or



oil can be dangerous and may result in re.

Clean only the parts listed in this guide.

Clean with caution. If a wet sponge or cloth is used to wipe spills on a hot surface, be careful to avoid steam burns. Some cleaners can produce noxious fumes if applied to a hot surface.

Page 5

2. Cooker Overview

DocNo.020-0006 - Overview - 100DF - Prof+

Fig.2-1

ArtNo.212-0019 - 110 DF Classic Deluxe front view

The 110 dual fuel cooker (Fig.2-1) has the following features:

A. Four hotplate burners with a wok burner and ceramic

multizone hotplate

B. A control panel C. A glide-out grill D. A multi-function oven E. A fan oven F. A storage drawer

Fig.2-2

Hotplate Burners

The drawing by each of the central knobs indicates which burner that knob controls.

Each burner has a Flame Supervision Device (FSD) that prevents the ow of gas if the ame goes out.

When a hotplate control knob is pressed in, sparks will be made at every burner – this is normal. Do not attempt to disassemble or clean around any burner while another burner is on, otherwise an electric shock could result.

To light a burner, push in and turn the associated control knob to the high position as indicated by the large ame symbol (

), (Fig.2-2).

Page 6

ArtNo.311-0002 Pan with rim

ArtNo.311-0001 Right pans gas

Fig.2-3

Art No. 311-0003 Simmer aids

ArtNo.311-0046 - Elan Wok burner

Fig.2-4

Fig.2-5

The igniter should spark and light the gas. Keep holding the knob pressed in to let the gas through to the burner for about ten seconds.

If, when you let go of the control knob, the burner goes out, then the FSD has not been bypassed. Turn the control knob to the ‘OFF’ position and wait for one minute before you try again, this time making sure to hold in the control knob for slightly longer.

Adjust the ame height to suit by turning the knob counterclockwise (Fig.2-3). On this cooker the low position is beyond high, NOT between high and o.

If a burner ame goes out, turn o the control knob and leave it for one minute before relighting it.

Make sure that the ames are under the pans. Using a lid will help the contents boil more quickly (Fig.2-4).

Large pans should be spaced well apart.

Pans and kettles with concave bases or down-turned base rims should not be used (Fig.2-5).

Fig.2-6

Fig.2-8

Fig.2-9

Fig.2-7

ArtNo.311-0004 Tipping wok

Simmering aids, such as asbestos or mesh mats, are NOT recommended (Fig.2-6). They will reduce burner performance and could damage the pan supports.

You should also avoid using unstable and misshapen pans that may tilt easily, and pans with a very small base diameter, e.g. milk pans, single egg poachers (Fig.2-7).

The minimum recommended pan diameter is 120 mm. The maximum allowable pan base diameter is 260 mm.

DO NOT use cooking vessels on the hotplate that overlap the edges.

Wok Burner

The wok burner is designed to provide even heat over a large area. It is ideal for large pans and stir-frying (Fig.2-8).

For heating smaller pans, the aforementioned hotplate burners may be more ecient.

You can remove the burner parts for cleaning; see ‘Cleaning Your Cooker’.

You should wipe the enamel top surface of the cooker around the hotplate burners as soon as possible after spills occur. Try to wipe them o while the enamel is still warm.

Fig.2-10

ArtNo.311-0006 Correct wok sizes

ArtNo.311-0007 Wok stand close-up

Note:

The use of aluminium pans may cause metallic marking of the pan supports. This does not aect the durability of the enamel and may be cleaned o with a suitable metal cleaner.

The Wok Cradle

The wok cradle is designed to t a 35 cm wok. If you use a dierent wok, make sure that it ts the cradle. Woks vary very widely in size and shape. It is important that it sits down on the pan support – however, if the wok is too small, the cradle will not support it properly (Fig.2-9).

The cradle should be used on the wok burners only. When you t the cradle, check that the wok is supported properly on a pan support and is sitting level in the cradle (Fig.2-10).

Page 7

The cradle will get very hot in use – allow plenty of time for it to cool before you pick it up.

The Ceramic Hotplate

The hotplate area on the left-hand side is dual purpose. It can be used either as a ceramic hob to heat a pan in the usual way (Fig.2-11) or it can be used to heat the supplied griddle.

The rear area, marked with a ring is for cooking with a pan.

There are two elements that allow either the whole of the area to be heated or just the rear half. To use the rear ring turn the control counter-clockwise (Fig.2-12).

Fig.2-11

The neon indicator light above the control knob will come on when a hob control is turned on and stay lit while the surface cools.

You can also place a large sh kettle across both heating zones. To heat the whole area, turn the knob clockwise.

Always take care before touching the surface even when it is turned o – it may be hotter than you think.

Use only pans that are suitable for ceramic hobs.

We recommend stainless steel and enamelled steel pans because pots and pans with copper or aluminium bases leave traces on the hob that are dicult to remove.

Pots and pans should have thick, smooth, at bottoms (Fig.2-13). This ensures the maximum heat transfer from the hob to the pan, making cooking quick and energy ecient. Never use a round-bottomed wok, even with a stand.

The very best pans have bases that are very slightly curved up when cold. If you hold a ruler across the bottom you will see a small gap in the middle (Fig.2-14). When they heat up the metal expands and lies at on the cooking surface.

Make sure that the base of the pan is clean and dry to prevent any residue burning onto the hob panel. This also helps prevent scratches and deposits.

Always use pans that are the same size as (or slightly larger than) the areas marked on the hob top (Fig.2-15). Using smaller pans wastes heat, and any spillage will be burnt on. Using a lid will help the contents boil more quickly.

Fig.2-12

Fig.2-13

Fig.2-14

Always lift pans o the hob. Sliding pans may cause marks and scratches. Always turn the control to the ‘OFF’ position before removing a pan.

When cooking on the hob you may see the hob area you are using switch o and on. This is caused by a safety device that limits the temperature of the hob. It is quite normal, especially when cooking at high temperatures. If it happens a lot with a particular pan however it may mean the pan is not suitable – perhaps too small or too uneven - for a ceramic hob.

For best results, preheat a covered serving dish for 10 minutes before adding food to it.

Use only heat-resistant dishes.

Fig.2-15

ArtNo.312-0006 Correct pan sizes

Page 8

Fig.2-16

Fig.2-17

The Griddle

The griddle (Fig.2-16) is designed to t securely on the locating pins over the ceramic heating area (Fig.2-17). Do not try to use it over one of the gas burners. It will not be securely held and you may damage the non-stick nish.

There are two elements that allow either the whole of the area to be heated or just the rear half.

To heat the whole area, turn the knob clockwise (Fig.2-18).

To heat the rear ring only, turn it counter-clockwise (Fig.2-19).

The neon indicator light above the control knob will come on when a hob control is turned on and stay lit while the surface cools.

It is designed for cooking food on directly. DO NOT use pans of any kind on it. The griddle surface is non-stick and metal cooking utensils (e.g. spatulas) will damage the surface. Use heat resistant plastic or wooden utensils.

The griddle can be lightly brushed with cooking oil before use.

Fig.2-18

Fig.2-19

Preheat the griddle for a maximum of 5 minutes before adding food. Leaving it longer may cause damage.

There is a gap at the right-hand rear corner of the griddle (Fig.2-20) so you can pour o excess fat after cooking. Be careful – it may be very hot.

After cooking, allow the griddle to cool before cleaning.

Fig.2-20

Page 9

The Glide-out Grill

Open the door and pull the grill pan carriage forward using the handle (Fig.2-21).

The grill has two elements that allow either the whole area of the pan to be heated or just the right-hand half.

To heat the whole grill, turn the control knob clockwise

(Fig.2-22).

Fig.2-21

To heat the right-hand half, turn the control knob counterclockwise. The neon indicator light by the grill control will come on.

For best results, slide the carriage back into the grill chamber and preheat the appropriate part(s) of the grill for two minutes. The grill trivet can be removed and the food placed on it while you are waiting for the grill to preheat.

DO NOT leave the grill on for more than a few



moments without the grill pan underneath it, otherwise the knobs may become hot.

Once the grill has preheated, slide the carriage out again. With the trivet back in place with the food on it, slide the carriage back into the grill chamber. Make sure that it is pushed right in.

Accessible parts may be hot when the grill is in use.



Young children should be kept away.

The grill pan trivet can be turned over to give two grilling positions (Fig.2-23).

Never close the grill door when the grill is on.



ArtNo.331-0001Grill pan pulled forwards

ArtNo.235-0007 - Classic

DL grill control

ArtNo.331-0002 Grill pan high/low position

Fig.2-22

Fig.2-23

Page 10

Function Use

Rapid Response To quickly heat up the oven

Defrost

Fan oven

Fanned grilling

Fan assisted

Conventional oven

Browning element

Base heat

To thaw small items in the oven without heat

A full cooking function, even heat throughout, great for baking

Grilling meat and fish with the door closed

A full cooking function good for roasting and baking

A full cooking function for roasting and baking in the lower half of the oven

To brown and crisp cheese topped dishes

To crisp up the bases of quiche, pizza or pastry

Table 2-1

The Ovens

The clock must be set to the time of day before the ovens will work. See the following section on ‘The Clock’ for instructions on setting the time of day.

References to ‘left-hand’ and ‘right-hand’ ovens apply as viewed from the front of the appliance.

The left-hand oven is a multi-function oven, while the righthand oven is a fan oven.

The Left-hand Multi-function Oven

As well as the oven fan and fan element, multi-function ovens are tted with two extra heating elements, one visible in the top of the oven and the second under the oven base. Take care to avoid touching the top element and element deector when placing or removing items from the ovens.

The multi-function oven has 3 main cooking functions, fan, fan assisted and conventional cooking. These functions should be used to complete most of your cooking.

The browning element and base heat can be used in the latter part of the cooking process to ne tune the results to your particular requirements.

Use fanned grilling for all your grilling needs and defrost to safely thaw small items of frozen food.

Table 2-1 gives a summary of the multi-function modes.

The multi-function ovens have many varied uses. We suggest you keep a careful eye on your cooking until you are familiar with each function. Remember – not all functions will be suitable for all food types.

Please remember that all cookers vary – temperatures in your new ovens may dier to those in your previous cooker.

Page 11

Multi-function Oven Functions

Rapid Response

The Rapid Response setting enables you to preheat the oven faster than normal. It uses the fan oven

element with additional heat from one of the elements in the top of the oven. Rangemaster fan ovens heat up quickly; but the Rapid Response feature speeds this process up enabling you to commence cooking sooner.

To use the Rapid Response feature, simply turn the function control knob to R and set the temperature you require. The light on the control panel adjacent to the R symbol will come on. When temperature is reached, the light will go out as will the element at the top of the oven. The fan element and oven fan will then continue to maintain your chosen oven temperature.

Should you choose to place food into the cold oven prior to cooking whilst using the Rapid Response function, make sure that cakes etc. are not positioned too near the top of the oven. As with any cooking, particularly poultry, meat and ready meals, be sure the food is piping hot before serving.

Fan Oven

This function operates the fan and the heating

element around it. An even heat is produced

throughout the oven, allowing you to cook large amounts quickly.

Fan oven cooking is particularly suitable for baking on several shelves at one time and is a good ‘all-round’ function. It may be necessary to reduce the temperature by approximately 10 °C for recipes previously cooked in a conventional oven.

If you wish to preheat the oven, wait until the indicator light has gone out before inserting the food.

Fanned Grilling

This function operates the fan whilst the top element

is on. It produces a more even, less erce heat than

a conventional grill. For best results, place the food to be grilled, on a grid over a roasting tin, which should be smaller than a conventional grill pan. This allows greater air circulation. Thick pieces of meat or sh are ideal for grilling in this way, as the circulated air reduces the erceness of the heat from the grill.

The oven door should be kept closed while grilling is in progress, so saving energy. You will also nd that the food needs to be watched and turned less than for normal grilling. Preheat this function before cooking.

For best results we recommend that the grill pan is not located on the uppermost shelf.

cooking time, as the heat at the top of the oven is greater than at the base, when using this function.

This is a fast intensive form of cooking; keep an eye on the food cooking until you have become accustomed to this function.

Conventional Oven (Top and Base Heat)

This function combines the heat from the top and base elements. It is particularly suitable for roasting and baking pastry, cakes and biscuits.

Food cooked on the top shelf will brown and crisp faster than on the lower shelf, because the heat is greater at the top of the oven than at the base, as in ‘Fan assisted oven’ function. Similar items being cooked will need to be swapped around for even cooking. This means that foods requiring dierent temperatures can be cooked together, using the cooler zone in the lower half of the oven and hotter area to the top.

Browning Element

This function uses the element in the top of the oven only. It is a useful function for the browning

or nishing of pasta dishes, vegetables in sauce, shepherds pie and lasagne, the item to be browned being already hot before switching to the top element.

Base Heat

This function uses the base element only. It will crisp

up your pizza or quiche base or nish o cooking

the base of a pastry case on a lower shelf. It is also a gentle heat, good for slow cooking of casseroles in the middle of the oven or for plate warming.

The Browning and Base Heat functions are useful additions to your oven, giving you exibility to nish o items to perfection.

Defrost

This function operates the fan to circulate cold air

only. Make sure the temperature control is at 0°C and

that no heat is applied. This enables small items such as desserts, cream cakes and pieces of meat, sh and poultry to be defrosted.

Defrosting in this way speeds up the process and protects the food from ies. Pieces of meat, sh and poultry should be placed on a rack, over a tray to catch any drips. Be sure to wash the rack and tray after defrosting.

Defrost with the oven door closed.

Large items, such as whole chickens and joints should not be defrosted in this way. We recommend this be carried out in a refrigerator.

Fan Assisted Oven

This function operates the fan, circulating air heated by the elements at the top and the base of the oven.

The combination of fan and conventional cooking (top and base heat) makes this function ideal for cooking large items that need thorough cooking, such as a large meat roast.

It is also possible to bake on two shelves at one time, although they will need to be swapped over during the

Defrosting should not be carried out in a warm oven or when an adjoining oven is in use or still warm.

Make sure that dairy foods, meat and poultry are completely defrosted before cooking.

Page 12

Fig.2-24

ArtNo.235-0003 - Classic DL MF knobs

Right-hand Fan Oven

The right-hand oven is a fan oven that circulates hot air continuously, which means faster, more even cooking.

The recommended cooking temperatures for a fan oven are generally lower than a conventional oven.

Note: Please remember that all cookers vary so temperatures in your new ovens may dier to those in your previous cooker.

Operating the Ovens

Fig.2-25

Fig.2-26

Temperature

ArtNo.235-0004 - Classic DL oven 1

Function

Operating the left-hand multi-function oven

The multi-function oven has two controls: a function selector and a temperature setting knob (Fig.2-24).

Turn the function selector control to a cooking function. Fig.2-25 shows the control set for conventional oven cooking.

Turn the oven temperature knob to the temperature required (Fig.2-26).

The oven heating light will glow until the oven has reached the temperature you selected (Fig.2-27). It will then cycle on and o during cooking as the oven maintains the selected temperature.

Operating the right-hand fan oven

Turn the oven knob to the desired temperature (Fig.2-26).

The oven indicator light will glow until the oven has reached the temperature selected (Fig.2-27). It will then cycle on and o during cooking.

Fig.2-27

ArtNo.235-0005 - Classic DL oven control 2

Page 13

The Clock

ArtNo.302-0004 -

Minute minder setting 2

ArtNo.302-0005a -

6BC Stopping the oven 1a

ArtNo.302-0006 - 6BC setting the cook time

ArtNo.302-0005a -

6BC Stopping the oven 1a

You can use the timer to turn the left-hand multi-function oven on and o. The clock must be set to the time of day before the ovens will work.

Fig.2-28

Setting the Time of Day

The 6-button LCD clock is shown in Fig.2-28. When the clock is rst connected the display ashes ( 0.00 ) and (G) alternately.

Press and hold both the [C] and [D] buttons down (Fig.2-29). Now press the [+] button (or the [–] button) until the correct time shows.

Do not forget that it is a 24-hour clock.

If you need to reset the cooker, turn o the power supply and wait for a couple of minutes and start again.

Setting the Minute Minder

Press and hold the [C] button (Fig.2-30), and then press the [+] button until the length of time you want to cook for is shown (Fig.2-31).

You can check the time remaining by pressing [C]. When the beeper sounds cancel it by pressing [C].

• The ‘cook period’, which is the length of time you want the oven to cook for.

• The ‘stop time’, which is the time of day you want the oven to stop cooking.

ArtNo.302-0002 - 6BC annotated

ABCDEF

A – Minute minder, B – ‘Cook’ time, C – ‘Stop’ time,

D – Manual, E & F – Time setting buttons

Fig.2-29

ArtNo.302-0001 - 6-button clock

Fig.2-30 Fig.2-31

ArtNo.302-0003 - 6BC minute minder setting 1

To Stop the Oven Automatically

Press and hold the ‘stop time’ [E] button (Fig.2-32) and then press the [+] button (or [–] button) until the required ‘stop time’ shows (Fig.2-33). AUTO will show in the display.

Once the ‘stop time’ is reached, the beeper sounds. To stop the beep turn the oven control knob to 0 rst and then press [B] once; press [B] again to return to manual cooking.

To Start and Stop the Oven Automatically

Before you set the clock you must have two numbers clearly in mind – the ‘cook period’ and the ‘stop time’.

Note: You cannot set a start time directly – this is set automatically by setting the ‘cook period’ and the ‘stop time’.

Press and hold the [D] button (Fig.2-34) and then press the [+] button (or [–] button) until the required ‘cook period’ shows (Fig.2-35).

Now press and hold the [E] button (Fig.2-36) and then press the [+] button (or [–] button) until the required ‘stop time’ shows (Fig.2-37). Release the buttons.

AUTO will now show in the display.

Set the oven to the required temperature. When cooking is nished the beeper will sound. Turn the oven knob to the OFF position rst, and then press the [B] button once to stop the beep; press it again to return to manual cooking.

Fig.2-32

ArtNo.302-0005 -

6BC Stopping the oven 1

Fig.2-34

Fig.2-33

Fig.2-35

Fig.2-36 Fig.2-37

ArtNo.302-0005 -

6BC Stopping the oven 1

If you are out, do not worry about the beeper going o, it stops after a while. When you return, turn the oven knob to 0 rst, and then press [B] twice to return to manual cooking.

Page 14

Fig.2-38 Fig.2-39

ArtNo.302-0008 Activating the key lock 1

ArtNo.302-0009 - Activating the key lock 2

Fig.2-40

AUTO is Showing, But you Want to Reset to Manual Cooking

To return to manual cooking from any automatic setting, the ‘cook period’ must be cancelled. Press and hold the [E] button and then press the [ –] button until the display reads ( 0.00 ).

Press the [B] button to return to manual cooking.

Key Lock

Activating the key lock will lock the left-hand oven and it will not come on.

Fig.2-41

Fig.2-42

ArtNo.302-0010 Activating the key lock 3

ArtNo.302-0011 - 6BC Deactivating the key lock 1

ArtNo.302-0012 Deactivating the key lock 2

The right-hand oven can be operated as usual.

To activate the key lock

Make sure that the clock is in manual mode and cancel any active programs.

Hold the Minute Minder [C] and Cook period [D] buttons. When ‘On’ appears on the display (Fig.2-38) press the [+] button once. The key symbol [F] and ‘OF’ will now show on the display (Fig.2-39). Release the buttons.

The left-hand oven is now locked, as conrmed by the display showing the time of day alongside the key symbol (Fig.2-40).

To turn o the key lock

Hold the Minute Minder [C] and Cook period [D] buttons. When ‘OF’ appears on the display (Fig.2-41) press the [+] button once. The key symbol [F] will go out and ‘On’ will show on the display (Fig.2-42). Release the buttons.

After a few seconds the display will revert to show the time of day.

The oven can now be used normally.

Page 15

Accessories

ArtNo.320-0012 Removing the shelf 2

Oven Shelves

In addition to the at shelves, your cooker is supplied with a drop shelf (Fig.2-43). The drop shelf increases the possibilities for oven shelf spacing.

The oven shelves can be easily removed and retted.

Pull the shelf forward until the back of the shelf is stopped by the shelf stop bumps in the oven sides (Fig.2-44).

Lift up the front of the shelf so the back of the shelf will pass under the shelf stop and then pull the shelf forward (Fig.2-45).

Flat shelf

Drop shelf

Fig.2-43

Shelf guard

Front

Shelf guard

To ret the shelf, line up the shelf with a groove in the oven side and push the shelf back until the ends hit the shelf stop. Lift up the front so the shelf ends clear the shelf stops, and then lower the front so that the shelf is level and push it fully back (Fig.2-46).

The Handyrack (Left-hand Oven)

The Handyrack (Fig.2-47) ts to the left-hand oven door only. Food cooking on it is easy to attend to, because it is accessible when the door is open.

The maximum weight that can be held by the Handyrack is 5.5 kg (12 lb). It should only be used with the supplied roasting tin, which is designed to t the Handyrack. Any other vessel could be unstable.

It can be tted at two dierent heights. One of the oven shelves must be removed and the other positioned to suit.

When the Handyrack is used in its highest position, other dishes can be cooked on the bottom shelf position or base of the oven.

When the Handyrack is used in its lowest position, other dishes can be cooked on the second shelf position or base of the oven.

To t the Handyrack, locate one side of it on the door bracket (Fig.2-48).

Front

Fig.2-44 Fig.2-45

ArtNo.320-0011 Removing the shelf 1

Fig.2-46

ArtNo.320-0013 Removing the shelf 3

Fig.2-47

Then spring the other side out to clip it onto the other bracket (Fig.2-49).

ArtNo.320-0014 Handyrack on LH door

Fig.2-48 Fig.2-49

ArtNo.320-0015

Fitting the Handyack 1

ArtNo.320-0016

Fitting the handyrack 2

Page 16

Fig.2-50

Oven Lights

Press the button to turn the lights on (Fig.2-50).

Fig.2-51

ArtNo.320-0017 Main oven light

ArtNo.340-0002 110 removing the drawer

If the oven light fails, turn o the power supply before changing the bulb. See the ‘Troubleshooting’ section for details on how to change the bulb.

Storage

The bottom drawer is for storing oven trays and other cooking utensils.

It can get very warm, so do not store anything in it that may melt or catch re.

Never store ammable materials in the drawer. This includes paper, plastic and cloth items, such as cookbooks, plastic ware and towels, as well as ammable liquids.

Do not store explosives, such as aerosol cans, on or near the appliance.

Flammable materials may explode and result in re



or property damage.

The drawer can be removed completely for cleaning, etc. by pulling it right out and up (Fig.2-51).

Page 17

3. Cooking Tips

Tips on Cooking with the Timer

If you want to cook more than one dish, choose dishes that require approximately the same cooking time. However, dishes can be ‘slowed down’ slightly by using small containers and covering them with aluminium foil, or ‘speeded up’ slightly by cooking smaller quantities or placing them in larger containers.

Very perishable foods such as pork or sh should be avoided if a long delay period is planned, especially in hot weather.

DO NOT place warm food in the oven to be timed.



DO NOT use a timed oven that is already warm.



DO NOT use the timed oven if the adjoining oven is



already warm.

Whole poultry must be thoroughly defrosted before being placed in the oven. Check that meat and poultry are fully cooked before serving.

Temperature (Gas Mark) Temperature (°C / °F)

1 140 / 275

2 150 / 300

3 160 / 325

4 175 / 350

5 190 / 375

6 205 / 400

7 220 / 425

8 230 / 450

Table 3-1 Temperature conversion table

General Oven Tips

The wire shelves should always be pushed rmly to the back of the oven.

Baking trays with food cooking on them should be placed level with the front edge of the oven’s wire shelves. Other containers should be placed centrally. Keep all trays and containers away from the back of the oven, as overbrowning of the food may occur.

For even browning, the maximum recommended size of a baking tray is 340 mm (13½”) by 340 mm (13½”).

When the oven is on, do not leave the door open for longer than necessary, otherwise the knobs may get very hot.

• Always leave a “finger’s width” between dishes on the same shelf. This allows the heat to circulate freely around them.

• To reduce fat splashing when you add vegetables to hot fat around a roast, dry them thoroughly or brush lightly with cooking oil.

• Where dishes may boil and spill over during cooking, place them on a baking tray.

• The ‘Cook & Clean’ oven liners (see ‘Cleaning Your Cooker’) work better when fat splashes are avoided.

Cover meat when cooking.

• Sufficient heat rises out of the oven while cooking to warm plates in the grill compartment.

• If you want to brown the base of a pastry dish, preheat the baking tray for 15 minutes before placing the dish in the centre of the tray.

Page 18

4. Cooking Table

DocNo.031-0004 - Cooking table - electric & fan single cavity

The oven control settings and cooking times given in the table below are intended to be used AS A GUIDE ONLY. Individual tastes may require the temperature to be altered to provide a preferred result.

Food is cooked at lower temperature in a fan oven than in a conventional oven. When using recipes, reduce the fan oven temperature by 10 °C and the cooking time by 5-10 minutes. The temperature in the fan oven does not vary with height in the oven so you can use any shelf.

Conventional Oven

Food Meat

Beef (no bone)

Lamb

Pork

Poultry

Chicken

Turkey

Duck

Casserole Yorkshire Pudding Cake

Very rich fruit - Christmas, wedding, etc. Fruit 180 mm tin Fruit 230 mm tin Madeira 180 mm Queen cakes Scones Victoria sandwich 180 mm tin 210 mm tin

Desserts

Shortcrust tarts Fruit pies Tartlets Puff pastry Meringues Baked egg custard Baked sponge pudding Milk pudding

Bread Fish

Fillet Whole Steak

Temperature °C (Shelf Position)

160 (C)

200 (C) 160 (C) 200 (C) 160 (C) 200 (C)

160 (C) 200 (C) 160 (C) 200 (C) 160 (C) 200 (C)

140-150 (C)

220 (C)

140 (C/B)

150 (C/B) 150 (C/B) 160 (C/B) 190 (C/B) 220 (C/B)

180 (C/B) 180 (C/B)

200 (C/B) 200 (C/B) 200 (C/B) 210 (C/B) 100 (C/B) 160 (C/B) 180 (C/B)

140-150 (C/B)

210 (C)

Fanned Grilling

190 (C/B) 190 (C/B) 190 (C/B)

Fan Oven

Temperature

°C

150 190 150 190 150 190

130-140

210

130

140 140 150 180 210

170 170

190 190 190 200

90 150 170

130-140

200

190 (C/B) 190 (C/B) 190 (C/B)

Approximate Cooking Time

ArtNo.050-0001 Gas cooking table

30-35 minutes per 500g +30-35 minutes. 20-25 minutes per 500g +20-25 minutes. 30-35 minutes per 500g +30-35 minutes. 25-30 minutes per 500g +25-30 minutes. 35-40 minutes per 500g +35-40 minutes. 25-30 minutes per 500g +25-30 minutes.

20-25 minutes per 500g +20-25 minutes. 15-20 minutes per 500g +15-20 minutes. 20 minutes per 500g +20 minutes. 15 minutes per 500g +15 minutes. 25-30 minutes per 500g. 20 minutes per 500g. 2-4 hours according to recipe. Large tins 30-35 minutes; individual 10-20 minutes.

45-50 minutes per 500g of mixture.

2-2½ hours. Up to 3½ hours. 80-90 minutes. 15-25 minutes. 10-15 minutes.

20-30 minutes. 30-40 minutes.

20-30 minutes on a preheated tray. 35-45 minutes. 10-20 minutes according to size. 20-40 minutes according to size. 2-3 hours. 45-60 minutes. 40-45 minutes. 2 to 3 hours. 20-30 minutes.

15-20 minutes. 15-20 minutes per 500g. Steaks according to thickness.

Top (T)

Centre (C)

Base (B)

ArtNo.050-0007

Oven shelf positions

Oven Shelf Positions

T - Top; C - Centre; B - Base

Thoroughly thaw frozen joints before cooking. Meat may be roasted at 220°C (210°C for fan oven) and the cooking time adjusted accordingly. For stuffed and rolled meats, add approximately 10 minutes per 500g, or cook at 200°C (190°C) for 20 minutes then 160°C (150°C) for the remainder.

For stuffed poultry, you could cook at 200°C (190°C) for 20 minutes then 160°C (150°C) for remainder. Do not forget to include the weight of the stuffing. For fresh or frozen prepacked poultry, follow instructions on the pack. Thoroughly thaw frozen poultry before cooking.

Using the conventional oven: when two tier cooking leave at least one runner space between shelves. Position the baking tray with the front edge along the front of the oven shelf.

Up to three tiers can be cooked in a fan oven at the same time but make sure to leave at least one runner space between each shelf being cooked on.

Using the conventional oven: for even browning the maximum size of baking tray recommended is 340 mm x 340 mm. This ensures free heat circulation. If cooking a two tier load, the trays should be interchanged approximately halfway though the cooking time.

Page 19

5. Cleaning Your Cooker

Essential Information

Isolate the electricity supply before carrying out any thorough cleaning. Allow the cooker to cool.

Never use paint solvents, washing soda, caustic



cleaners, biological powders, bleach, chlorine based bleach cleaners, coarse abrasives or salt.

Do not mix dierent cleaning products – they may



react together with hazardous results.

All parts of the cooker can be cleaned with hot soapy water – but take care that no surplus water seeps into the

appliance.

Remember to switch on the electricity supply and reset the clock before re-using the cooker.

Hotplate Burners

The burner heads and caps can be removed for cleaning.

DO NOT put the burner heads in a dishwasher.



Make sure they are absolutely dry before replacing them.

The Single Ring Burners

When retting the burner head, make sure that the notch lines up with the electrode or hole in the base. Check that the burner head is level and that the cap is tted centrally on the burner head (Fig.5-1).

The Wok Burner

The wok burner can also be taken apart for cleaning.

When reassembling the wok burner (Fig.5-2), turn over the large base ring and nd the ‘D’ shaped area (Fig.5-3). Turn the head until the ‘D’ matches the one on the burner base. Flip the burner over once again and place it on the burner base.

To t the small inner burner, nd the larger electrode notch in the burner rim. Line this up with the white ignition electrode and place the inner burner on the large base ring (Fig.5-4).

ArtNo.311-0032 Burner layout FSD

A – Cap, B – Head, C – Notch, D – Base, E – Electrode

Fig.5-1

Fig.5-2

ArtNo.311-0033 Wok burner details FSD

A – Inner burner cap, B – Outer burner cap, C – Inner burner head,

D – Outer burner head, E – Wok burner base

Fig.5-3

Now t the two burner caps, making sure that they are seated properly.

Check the burner ports are not blocked. If a blockage occurs, remove stubborn particles using a piece of fuse wire.

The Wok Cradle

Recommended cleaning materials are hot soapy water, a moistened soap pad, cream cleaner or a nylon scourer.

ArtNo.311-0016 Fitting the burner inner head

A – Electrode notch, B – Ignition electrode

Fig.5-4

Page 20

Fig.5-5

Ceramic Hotplate

Daily Care

First of all, make sure that the heat indicator light is o and that the cooking surface is cool.

Apply a small dab of ceramic cleaning cream in the centre of the area to be cleaned. Dampen a clean paper towel and work the cream onto the cooking surface. As a nal step, wipe the cooking surface with a clean, dry paper towel.

Cleaning Spills

For spills and boil-overs that occur while cooking, turn o the unit and wipe the area surrounding the hot zone with a clean paper towel. If a spill (other than a sugary substance) is on the hot zone, do not clean until the unit has completely cooled down, and then follow the instructions below, ‘Cleaning Burned-on Spills’.

If you accidentally melt anything on the surface or if you spill foods with a high sugar content (preserves, tomato sauce, fruit juice, etc.), remove the spill IMMEDIATELY with a razor scraper, while the unit is still hot.

IMPORTANT: Use an oven glove to protect your hand from potential burns.

Scrape the major spill or melted material from the cooking zone and push into a cold area. Then, turn the unit ‘OFF’ and allow to cool before cleaning further. After the cooking surface cools down and the heat indicator lights go o, follow the ‘Daily Care’ procedure outlined above.

Cleaning Burned-on Spills

Make sure that the heat indicator lights are o and that the hob is cool. Remove the excess burned-on substance with a single-edged razor scraper. Hold the scraper at an angle of about 30° to the surface and then scrape o the burned-on matter (Fig.5-5).

Once you have removed as much as possible with the scraper, follow the ‘Daily Care’ procedure outlined above.

To Remove Metal Rub-oﬀ

Sliding pans on the hob – especially aluminium or copper pans – can leave marks on the ceramic surface. These marks often appear like scratches, but can easily be removed (see ‘Cleaning Spills’). If the rub-o marks are especially stubborn, use a cleaning cream together with the razor.

The Griddle

Always clean the griddle after use. Allow it to cool completely before removing. Immerse the griddle plate in hot soapy water. Use a soft cloth or, for stubborn stains, a nylon washing up brush.

Note: If the griddle is washed in a dishwasher then some dishwasher residue may appear on the back. This is normal and will not aect the performance of your griddle.

Page 21

Glide-out Grill

The grill pan and trivet should be washed in hot soapy water. Alternatively, the grill pan can be washed in a dishwasher.

After grilling meats or any foods that soil, leave to soak for a few minutes immediately after use. Stubborn particles may be removed from the trivet using a nylon brush.

Before you remove any of the grill parts for cleaning,



make sure that they are cool, or use oven gloves.

DO NOT use any abrasive substances.



The grill pan can be easily removed for cleaning as follows. Remove the grill pan support frame by pulling the grill pan forward (Fig.5-6).

ArtNo.331-0001Grill pan pulled forwards

ArtNo.331-0003 Grill frame out, no pan

Fig.5-6

Fig.5-7

Lift the grill pan clear of the support frame. is held to the side rails by two clips on each side (Fig.5-7).

For each side, support the side rail with one hand and with the other hand lift the frame up and out of the side clips (Fig.5-8).

For safety, push the side rails back into the grill chamber.

If you need to remove the side rails to allow cleaning of the grill chamber, you can unhook them from the grill chamber sides (Fig.5-9) and wipe the sides clean with a soft cloth and mild detergent.

DO NOT put the side runners in a dishwasher.



Once you have nished, hook the side rails back onto the sides of the chamber. To ret the frame, pull the side rails forward and, for each side in turn, support the side rail and press the frame down into the side rails.

Replace the grill pan. When retting the grill pan, make sure that the wide rim is at the front (Fig.5-10).

The support frame

Fig.5-8

ArtNo.331-0004 Removing the grill frame

Fig.5-9

ArtNo.331-0005 Removing the grill rail

Fig.5-10

ArtNo.331-0006 Grill pan plan

Page 22

Fig.5-11

Fig.5-12

ArtNo.320-0002a Proplus oven door side screws

Control Panel and Doors

Avoid using any abrasive cleaners, including cream cleaners. For best results, use a liquid detergent.

The same cleaner can also be used on the doors. Alternatively, use a soft cloth wrung out in clean hot soapy water. You can use the same method for cleaning the control panel and knobs. After cleaning, polish with a dry cloth.

Glass Fronted Door Panels

The oven door front panels can be taken o so that the glass panels can be cleaned. Move the cooker forward to gain access to the sides (see the ‘Moving the Cooker’ section under ‘Installation’).

Open the oven door slightly and remove the front panel xing screws from the door sides, two each side (Fig.5-11).

Carefully lift o the outer door panel. The inside face of the glass panels can now be cleaned – take care not to disturb or wet the door insulation.

Note: If the door is triple glazed then the inner two panels are xed together and should not be separated. After cleaning, carefully ret the outer door panel and replace the side xing screws.

DO NOT use harsh abrasive cleaners or sharp metal



scrapers to clean the oven door glass since they can

scratch the surface, which may result in shattering of the glass.

Ovens

'Cook & Clean' Panels

The ovens have side ‘Cook & Clean’ panels which have been coated with a special enamel that partly cleans itself. This does not stop all marks on the lining, but helps to reduce the amount of manual cleaning needed.

These panels work better above 200 °C. If you do most of your cooking below this temperature, occasionally remove the panels and wipe with a lint free cloth and hot soapy water. The panels should then be dried and replaced and the oven heated at 200 °C for about one hour. This will make sure that the panels are working eectively.

Removing the Panels to Clean the Enamel Interior

Some of the lining panels can be removed for cleaning.

If you wish to clean the enamel interior of the oven, you will need to remove the shelves before removing the ‘Cook & Clean’ panels. You do not have to remove the support brackets to remove the panels. Lift each panel upward and slide forward o the support brackets (Fig.5-12).

Once the panels have been removed, the oven enamel interior can be cleaned.

DO NOT use steel wool, oven cleaning pads, or any other materials that will scratch the surface.

Ret in the reverse order.

Page 23

Cleaning Table

Cleaners listed (Table 5-1) are available from supermarkets or electrical retailers as stated.

For enamelled surfaces use a cleaner that is approved for use on vitreous enamel.

Regular cleaning is recommended. For easier cleaning, wipe up any spillages immediately.

Hotplate

Part Finish Recommended Cleaning Method

Hob top (including burner heads and caps)

Ceramic/Induction hob Toughened glass Hot soapy water; cream cleaner/scourer if necessary.

Griddle plate (some models only) Non-stick surface

Warming zone (some models only) Toughened glass Hot soapy water, cream cleaner/scourer if necessary.

Outside of Cooker

Part Finish Recommended Cleaning Method

Door, door surround and storage drawer exterior

Sides and plinth Painted surface Hot soapy water, soft cloth.

Enamel, stainless steel, aluminium

Enamel or paint

Stainless steel

Hot soapy water, soft cloth. Any stubborn stains remove gently with a nylon scourer.

Allow to cool. Wash in hot soapy water. Do not use abrasive cleaners/scourers. Dishwasher.

Hot soapy water, soft cloth. Any stubborn stains, remove gently with a liquid detergent.

E-cloth (electrical retailers) or microbre all-purpose cloth

(supermarket).

Splashback/rear grille Enamel or stainless steel Hot soapy water, soft cloth. Cream cleaner, with care, if necessary.

Control panel Paint, enamel or stainless steel Warm soapy water. Do not use abrasive cleaners on lettering.

Control knobs/handles & trims

Oven door glass/Glass lid (some models only)

Plastic/chrome, copper or lacquered brass

Brass Brass polish.

Toughened glass Hot soapy water, cream cleaner/scourer if necessary.

Warm soapy water, soft cloth.

Oven and Grill

Part Finish Recommended Cleaning Method

Sides, oor & roof of oven NOT ‘COOK & CLEAN’ OVEN PANELS (see

below)

‘Cook & Clean’ oven panels (some models only)

Oven shelves, Handyrack, grill trivet, Handygrill rack (some models only)

Grill pan/meat tin (some models only)

Enamel

Special enamel that partly cleans itself

Chrome

Enamel Hot soapy water. Soap lled pad. Dishwasher.

Any proprietary oven cleaner that is suitable for enamel. CAUTION: CORROSIVE/CAUSTIC OVEN CLEANERS: FOLLOW

MANUFACTURER’S INSTRUCTIONS. Do not allow contact with the oven elements.

This surface cleans itself at 200 °C and above, or the panels can be removed and washed with hot soapy water and a nylon brush.

An oven interior cleaner that is suitable for chrome. Soap lled pad. Dishwasher.

Table 5-1

Page 24

6. Troubleshooting

Hotplate ignition or hotplate burners faulty

Is the power on? Is the clock illuminated?

If not, there maybe something wrong with the power supply.

Are the sparker (ignition electrode) or burner slots blocked by debris?

Are the burner trim and caps correctly located? See the section on ‘Cleaning’.

Hotplate burners will not light

Make sure that the burner parts have been replaced correctly after wiping or removing for cleaning.

Check that there is not a problem with your gas supply. You can do this by making sure that other gas appliances you may have are working.

Do the burners spark when you push the button?

If not, verify that the power is on by checking that the clock is illuminated.

Steam is coming from the oven

When cooking foods with high water content (e.g. oven fries) there may be some steam visible at the rear grille.

Power failure

In the event of a failure in the electrical supply, remember to reset the clock to make sure that the timed oven continues to operate.

Food is cooking too slowly, too quickly, or burning

Cooking times may dier from your previous oven.

Check that you are using the recommended temperatures and shelf positions – see the oven cooking guide. The oven control settings and cooking times are intended to be used only as a guide.

Individual tastes may require the temperature to be altered either way, to get the results you want.

The oven is not cooking evenly

Do not use a baking tray with dimensions larger than those specied in the section on ‘General Oven Tips’.

If you are cooking a large item, be prepared to turn it round during cooking.

If two shelves are used, check that space has been left for the heat to circulate. When a baking tray is put into the oven, make sure that it is placed centrally on the shelf.

Take care when opening the oven door, as there may be a momentary pu of steam when the oven door is opened. Stand well back and allow any steam to disperse.

What cleaning materials are recommended for the cooker?

See the ‘Cleaning’ section for recommended cleaning materials.

Never use caustic or abrasive cleaners as these will



damage the surface.

An oven fan is noisy

The note of the oven fan may change as the oven heats up – this is perfectly normal.

The knobs get hot when I use the oven or the grill. Can I avoid this?

Yes, this is caused by heat rising from the oven or the grill, and heating them up. Do not leave the oven door open.

Make sure that the grill pan is pushed right back to the ‘back stop’ when grilling.

Check that the door seal is not damaged and that the door catch is adjusted so that the door is held rmly against the seal.

A dish of water when placed on the shelf should be the same depth all over. (For example, if it is deeper at the back, then the back of the cooker should be raised up or the front lowered.) If the cooker is not level arrange for your supplier to level it for you.

Oven not coming on

Is the power on? Is the clock illuminated? If not, there may be something wrong with the power supply.

Is the cooker supply on at the isolator switch?

Has the time of day been set?

Is the key symbol [ that the oven is locked? See the ‘Clock’ section of the instructions for more information on the key lock feature.

The timed oven is not coming on when automatic cooking

Has the oven knob been left in the OFF position by mistake?

F] showing in the display to signify

Always grill with the grill compartment door open.

If there is an installation problem and I don’t get my original installer to come back to x it who pays?

You do. Service organizations will charge for their call outs if they are correcting work carried out by your original installer. It is in your interest to track down your original installer.

Is the oven locked (see above)?

Oven temperature getting hotter as the cooker gets older

If turning the temperature down using the oven control knob has not worked, or has only worked for a short time, then you may need a new thermostat. This should be tted by a service person.

Page 25

An oven light is not working

The bulb has probably burnt out. You can buy a replacement bulb (which is not covered under the warranty) from a good electrical shop. Ask for a 15 W – 230 V lamp, FOR OVENS. It must be a special bulb, heat resistant to 300 °C (Fig.6-1).

Turn o the power at the circuit breaker.

Before removing the existing bulb, turn o the power supply and make sure that the oven is cool. Open the oven door and remove the oven shelves.

Unscrew the bulb cover by turning counter-clockwise. It may be very sti (Fig.6-2).

Taking care to protect your ngers with a glove in case the bulb should shatter, unscrew the old bulb.

Screw in the new bulb; screw back the bulb cover. Turn on the circuit breaker and check that the bulb now lights.

The oven door is misaligned

The bottom hinge of either oven door can be adjusted to alter the angle of the door (Fig.6-3). Loosen the bottom hinge xing screws and use the notch and a at bladed screwdriver to move the position of the hinge to set the hinge position (Fig.6-4).

Fig.6-1

ArtNo.324-0005 Oven light bulb

Fig.6-2

ArtNo.324-0007 Unscrewing the bulb cover

Fig.6-3

Retighten the hinge screws.

Eect of hinge adjustment – exaggerated for clarity

Centre line of hinge pin

ArtNo.320-0007 Oven door hinge adjustment 2

Oven door omitted for clarity

Fig.6-4

Page 26

INSTALLATION

Check the appliance is electrically safe and gas sound when you have nished.

7. Installation

Service and Spares

Firstly, please complete the appliance details below and keep them safe for future reference – this information will enable us to accurately identify the particular appliance and help us to help you. Filling this in now will save time and inconvenience if you later have a problem with the appliance. It may also be of benet to keep your purchase receipt with this leaet. You may be required to produce the receipt to validate a warranty eld visit.

Retailer’s Name and Address Andi-Co Appliance Pty Ltd.

1 Stamford Road, Oakleigh, VIC 3166

Tel: (03) 1300 650 020 Fax: (03) 9569 1450 Email: Service@andico.com.au

Name of Appliance Classic Deluxe 110 Dual Fuel

Appliance Serial Number*

Fuel Type Dual Fuel

Date of Purchase

Installer’s Name, Address and Telephone No.

Date of Installation

* This information is on the appliance data badge.

If you Have a Problem

In the unlikely event that you have a problem with your appliance, please refer to rest of this booklet, especially the problem solving section, rst to check that you are using the appliance correctly.

If you are still having diculty, contact you retailer.

Please Note

If your appliance is outside the 12-month warranty period, our service provider may charge for this visit.

If you request an engineer to visit and the fault is not the responsibility of the manufacture, our service provider reserves the right to make a charge.

Appointments not kept by you may be subject to a charge.

Out of Warranty

We recommend that our appliances are serviced regularly throughout their life to maintain the best performance and eciency. The frequency of service will depend on usage – for normal usage once a year should suce.

Service work should only be carried out by a suitably Authorised Person.

Spare Parts

To maintain optimum and safe performance, we recommend that only genuine spare parts are used. Do not use reconditioned or unauthorised controls. Contact your retailer.

Page 27

INSTALLATION

Check the appliance is electrically safe and gas sound when you have nished.

Dear Installer

Before you start your installation, please complete the details below, so that, if your customer has a problem relating to your installation, they will be able to contact you easily.

Installer’s Name

Installer’s Company

ArtNo.050-0011 - Installer information table

Installer’s Telephone Number

Appliance Serial Number

Provision of Ventilation

This appliance is not connected to a combustion products evacuation device. Particular attention shall be given to the relevant requirements regarding ventilation.

The room containing the cooker should have an adequate air supply.

Install the cooker in a location to allow the complete combustion of gas, proper ueing and to maintain ambient temperature of the immediate surroundings at safe limits, under normal condition.

Location of Cooker

The cooker may be installed in a kitchen/kitchen diner but NOT in a room containing a bath or shower.

Note: An appliance for use on Propane must not be installed in a room or internal space below ground level, e.g. in a basement.

Conversion

All models are supplied set for use on Natural gas. A conversion kit for Propane gas is included with the appliance. See the instructions that are supplied with the conversion kit.

You must be aware of the following safety requirements & regulations.

Prior to installation, make sure that the local distribution conditions (nature of the gas and gas pressure) and the adjustment of the appliance are compatible.

The appliance must be installed in accordance with the regulations in force and only in a well ventilated space.

Read the instructions before installing or using this appliance.

The regulations and standards are as follows:

AS 5601 – ‘Gas Installations’

In your own interest and that of safety, it is law that all gas appliances be installed by competent persons.

Failure to install the appliance correctly could



invalidate any warranty or liability claims and lead to prosecution.

The cooker must be installed in accordance with all local gas tting regulations, municipal building codes, electrical wiring regulations and any other relevant statutory regulations.

After converting the appliance, please attach the Gas Conversion sticker over the appropriate area of the data badge – this will identify the gas type for which the appliance is now set.

WARNING!



Where this appliance is installed in a marine craft, caravan or mobile home, it shall NOT be used as a space heater.

Page 28

INSTALLATION

Check the appliance is electrically safe and gas sound when you have nished.

Location of Cooker

The cooker may be installed in a kitchen/kitchen diner but NOT in a room containing a bath or shower.

This appliance is designed for domestic cooking only. Use for any other purpose could invalidate any warranty or liability claim.

Note: An appliance for use on LPG must not be installed

in a room or internal space below ground level, e.g. in a basement.

Conversion

All models are supplied set for use on Natural gas. A conversion kit for Propane gas is included with the appliance.

After converting the appliance, please attach the Gas Conversion sticker over the appropriate area of the data badge – this will identify the gas type for which the appliance is now set.

You will need the following equipment to complete the cooker installation satisfactorily:

• Stability bracket: If the cooker is to be supplied with gas through a flexible hose, a stability bracket or chain MUST be fitted. These are not supplied with the cooker but are available at most builders’ merchants.

• Gas pressure tester/manometer.

• Flexible gas hose: Must be in accordance with the

relevant standards.

• Multimeter: For electrical checks.

Checking the parts:

3 pan supports Wok cradle

ArtNo.000-0009 Wok ring, cast

Griddle Grill pan and trivet

ArtNo.330-0001 - Grill pan

3 at shelves 1 drop shelf

Handyrack Roasting tin

ArtNo.324-0003 Handyrack

ArtNo.324-0004 Roasting tin

You will also need the following tools:

Electric drill

2. Masonry drill bit (only required if tting the cooker on a

stone or concrete oor)

3. Wall plugs (only required if tting the cooker on a stone

or concrete oor)

4. Steel tape measure

5. Cross head screwdriver

6. Flat head screwdriver

7. Spirit level

8. Pencil

9. Adjustable spanner

10. Screws for tting stability bracket

11. 13 mm spanner or socket wrench

2-piece plinth Splashback

ArtNo.350-0012 - splashback

1 large and 4 small handles Stability bracket

ArtNo.210-0014 - Classic handles

Restraining chain & hook

ArtNo.020-0021 - Restraining chain & hook

Page 29

INSTALLATION

ArtNo.110-0073 110 Cooker min spacings

75 mm

min

75 mm

min

650 mm

min

905 mm

min

930 mm

max

Check the appliance is electrically safe and gas sound when you have nished.

Positioning the Cooker

Fig.7-1 shows the minimum recommended distance from the cooker to nearby surfaces.

The cooker should not be placed on a base.

The hotplate surround should be level with, or above, any adjacent work surface. A gap of 75 mm should be left between each side of the cooker ABOVE the hotplate level and any adjacent vertical surface.

For non-combustible surfaces (such as unpainted metal or ceramic tiles), this can be reduced to 25 mm.

A minimum space of 650 mm is required between the top of the hob and a horizontal combustible surface.

Fig.7-2 shows the suggested clearances above the cooker.

*Any cookerhood should be installed in accordance with the hood manufacturer’s instructions.

** Any splashback must be tted in accordance with the manufacturers instructions. Allowance should be made for the additional height of the ue trim, which is tted to the cooker hob.

Surfaces of furniture and walls at the sides and rear of the appliance should be heat, splash and steam resistant. Certain types of vinyl or laminate kitchen furniture are particularly prone to heat damage and discolouration. We cannot accept responsibility for damage caused by normal use of the cooker to any material that de-laminates or discolours at temperatures less than 65 °C above room temperature.

410 mm

min

1100 mm min*

Fig.7-1

Fig.7-2

Fig.7-3

We recommend a gap of 1110 mm between units to allow for moving the cooker. Do not box the cooker in – it must be possible to move the cooker in and out for cleaning and servicing.

If the cooker is near a corner of the kitchen, a clearance of 130 mm is required to allow the oven doors to open (Fig.7-3). The actual opening of the doors is slightly less, but this allows for some protection of your hand as you open the door.

Moving the Cooker

On no account try and move the cooker while it is



plugged into the electricity supply.

The cooker is very heavy, so take great care.



We recommend that two people manoeuvre the cooker. Make sure that the oor covering is rmly xed, or removed, to prevent it being disturbed when moving the cooker around.

To help you, there are two levelling rollers at the back, and two screw-down levelling feet at the front.

Remove the polystyrene base pack. From the front, tilt the cooker backwards and remove the front half of the polystyrene base (Fig.7-4).

130 mm min

Fig.7-4

Repeat from the back and remove the rear half of the polystyrene base.

Page 30

INSTALLATION

Check the appliance is electrically safe and gas sound when you have nished.

Fig.7-5

Fig.7-6

Fig.7-7

ArtNo.010-0004 Moving the cooker

Stability bracket

ArtNo.070-0014 - Stability bracket - Wall fitting

3 mm min

Cooker

Floor

Lowering the Two Rear Rollers

To adjust the height of the rear of the cooker, rst t a 13 mm spanner or socket wrench onto the hexagonal adjusting nut (Fig.7-5). Rotate the nut – clockwise to raise – counterclockwise to lower.

Make 10 complete (360°) turns clockwise.

Make sure you lower BOTH REAR ROLLERS.

Completing the Move

Unfold the rear edge of the cardboard base tray. Open the oven doors so that you can get a good grip on the bottom of the fascia panel as you move the oven (Fig.7-6).

Carefully push the cooker backwards o the base tray. Remove the base tray.

Position the cooker close to its nal position, leaving just enough space to get behind it.

DO NOT use the door handles or control knobs to



manoeuvre the cooker.

Fitting the Stability Bracket and Chain

A stability bracket and chain MUST be tted when



the cooker is connected to a exible gas supply.

Unless properly installed, the cooker could be tipped by leaning on the door. Injury might result from spilled hot liquids or from the cooker itself.

IMPORTANT: The cooker must be set to the correct height and levelled before the stability bracket is installed.

Fig.7-8

Fig.7-9

Typical oor mounting

Outer stability

bracket

3 mm min

Wall

Typical wall mounting

Restraining

chain

ArtNo.011-0007 - Restraining chain (AUS)

Cooker

Floor

Fitting a Stability Bracket

When tting a stability bracket please refer to the instructions supplied with the bracket for further details on tting.

When tting a stability bracket (Fig.7-7 and Fig.7-8) adjust the bracket to give the smallest practicable clearance between the bracket and the engagement slot in the rear of the cooker.

Fit the bracket so that it engages as far as possible over the chassis of the cooker.

Fitting the Restraining Chain

The restraining chain MUST be tted.

The length of chain between the appliance and the wall xing should prevent strain on the gas and electricity connections, but still allow access to unhook the chain when the cooker is pull forward.

Measure the length of chain required. Use the clamp supplied to clamp onto the gas pipe (Fig.7-9). Fix the supplied hook securely to the wall.

Page 31

INSTALLATION

ArtNo.215-0026 - Handle gaskets fixed

ArtNo.210-0006 - Classic fitting the handles 2

Art No 215-0028 - Handrail fascia fixings

Check the appliance is electrically safe and gas sound when you have nished.

Repositioning the Cooker Following Connection

If you need to move the cooker once it has been connected then you need to unplug it and, having gripped under the fascia panel and lifted the front of the cooker slightly (Fig.7-6), you need to check behind the cooker to make sure that the gas hose is not caught.

As you progress, make sure that both the electricity cable and gas hose always have sucient slack to allow the cooker to move.

With a stability chain tted, release it as you ease the cooker out. Do not forget to ret it when you replace the cooker.

When you replace the cooker, again check behind to make sure that the electricity cable and gas hose are not caught or trapped.

Conversion to Another Gas

If the appliance is to be converted to another gas do the conversion at this point. See the conversion section of these instructions and see the instructions in the conversion kit.

Fitting the Handles and Handrail

Remove the 4 mm Allen screws from the doors (Fig.7-10). Fit the door handles and secure using the 4 mm screws

(Fig.7-11).

Fig.7-10

Fig.7-11

Fig.7-12

The handles should be above the xings.



Remove the 4 mm Allen screws from the top corners of the fascia (Fig.7-12). Fit the front handrail in position and secure using the 4 mm screws.

Levelling

You are recommended to use a spirit level on a shelf in one of the ovens to check for level.

Place the cooker in its intended position taking care not to twist it within the gap between the kitchen units as damage may occur to the cooker or the units.

The front feet and rear rollers can be adjusted to level the cooker.

To adjust the height of the rear of the cooker use a 13 mm spanner or socket wrench to turn the adjusting nuts at the front bottom corners of the cooker.

To set the front, turn the feet bases to raise or lower.

Page 32

INSTALLATION

Check the appliance is electrically safe and gas sound when you have nished.

Fig.7-13

600

350

100

250

Gas inlet block

All dimensions in millimetres

Position for gas supply connector

Gas Connection

This must be in accordance with the relevant standards.

The exible hose (not supplied with the cooker) must be in accordance with the relevant standards. Hoses may be purchased at most builders’ merchants.

The gas supply needs to terminate with a down-facing bayonet.

The connector is located just below the hotplate level at the rear of the cooker. If in doubt contact your supplier.

The rear cover boxes limit the position of the supply point.

Because the height of the cooker can be adjusted and each connection is dierent, it is dicult to give precise dimensions.

Although a 900 mm hose can be used, a 1250 mm hose will allow slightly more exibility in the positioning of the bayonet and make moving the cooker easier.

The hose should be tted so that both inlet and outlet connections are vertical so that the hose hangs downwards in a ‘U’ shape.

Ideally the hose supply connection should be within the shaded area (Fig.7-13).

For Natural Gas, the exible hose must be in accordance with BS 669. For LP Gas, it should be capable of 50 mbar pressure, 70 °C temperature rise, and carry a red stripe, band or label. If in doubt contact, your supplier.

Screw connect the threaded end of the hose into the gas inlet.

After completing the gas connection, make sure that the cooker is gas sound with a pressure test.When checking for gas leaks do not use washing up liquid – this can corrode. Use a product specically manufactured for leak detection.

Natural Gas

The adjustable spring loaded gas pressure regulator is preset to give a nominal pressure of 1 kPa on Natural gas. Connect to the Rp½ inlet on the underside of the pressure regulator.

Propane

This cooker is supplied ready for use on Natural gas. A conversion kit for Propane gas is supplied with the cooker – see the ‘Conversion to Propane Gas’ section.

Pressure Testing

The pressure test point is accessible on the inlet pipe at the rear. Remove the test nipple screw and t a pressure gauge to the test point. Turn on and light two of the hotplate burners.

For Natural Gas cookers the pressure should be between

0.95kPa and 1.0kPa.

For Propane X cookers the pressure should be 2.54 kPa.

Page 33

INSTALLATION

Check the appliance is electrically safe and gas sound when you have nished.

Electrical Connection

This appliance must be installed by a qualied electrician to comply with the relevant regulations (AS/NZS 60335.2.6) and also the local electricity supply company requirements.

Make sure that the mains characteristics (voltage, nominal, power, etc.) match the ratings indicated on the cooker data plate.

Current Operated Earth Leakage Breakers

The combined use of your cooker and other domestic

appliances may cause nuisance tripping, so we

recommend that the cooker is protected on an individual

RCD (Residual Current Device) or RCBO (Residual Current

Breaker with Overload).

IF IN DOUBT, PLEASE CONSULT A SUITABLY QUALIFIED

ELECTRICIAN.

The cooker is preset for a single-phase earthed electrical connection. It is essential to install a multi-pole circuit breaker that completely disconnects the appliance from the mains, with a minimum contact break distance of 3 mm.

WARNING: THIS APPLIANCE MUST BE EARTHED.



The appliance must be connected to an ecient earthing circuit. If the electricity network is not equipped with an earth connection, then it must be installed separately in compliance with local regulations.

Earthing is a safety measure required by law, and must be performed with particular care by a qualied technician, who must also check that the electricity supply characteristics are correct.

Fig.7-14

ArtNo.132-0001 - 1 phase 240Vac 50Hz

1-phase 220-240 VAC 50 Hz

Fig.7-15

ArtNo.132-0003 - Single-phase connections (AUS)

A N

Fig.7-16

The total electrical load of the appliance is approximately

10.8 kW. The cable size used should be suitable for this load

and comply with all local requirements (i.e. PVC Insulated cable IEC 60227 – code 53 for ordinary cables).

Please note the maximum cable sizes are 6 mm² for the screw terminals and 10 mm² for the 3-pronged links.

Access to the mains terminal is gained by removing the electrical terminal cover box on the back panel. Connect the mains cable to the correct terminals for your electrical supply type (Fig.7-14 and Fig.7-15). tted and that the terminal screws are tight. Secure the mains cable using the cable clamp.

Check that the links are correctly

Fixed Wiring

For connection to xed wiring, i.e. exible conduit, remove the electrical terminal cover box on the back panel. Using the two screws, x the strain relief bracket in position.

Fix the conduit-to-conduit mounting bracket onto the strain relief bracket. Connect the mains cable to the correct terminals for your electrical supply type (Fig.7-16 and Fig.7-17). Check that the links are correctly tted and that the terminal screws are tight.

Replace the electric terminal cover box; make sure that the conduit is clear of the bottom ange.

ArtNo.132-0002 - 3 phase 240/415Vac 50Hz

3-phase 400-415 VAC 50 Hz

Mains terminal

Fixing bracket for

conduit connection

Cable clamp

ArtNo.132-0005 - Fixed wiring connection 2 (AUS)

Conduit

Fig.7-17

Page 34

INSTALLATION

ArtNo.350-0011 - Fitting the plinth 2 (Kitchener)

Outer plinth

Outer plinth xing screw

Inner plinth

Check the appliance is electrically safe and gas sound when you have nished.

Fig.7-18

Fig.7-19

ArtNo.350-0010 - Fitting the plinth 1 (Kitchener)

Final Checks

Hob Check

Check each cooking zone in turn. Be sure to use pans of the correct size and material.

Grill Check

Turn on the grill control and check that the grill heats up.

Oven Check

Set the clock as described earlier, and then turn on the ovens. Check the oven fan start to turn and that the ovens heat up.

Final Fitting

Fitting the Plinth

Fit the inner plinth to the bottom front of the cooker using the 4 screws provided (Fig.7-18).

Fit the outer plinth (2 screws, 1 each end) to the inner plinth. The height of the outer plinth can be adjusted by sliding it up or down via the slotted hole (Fig.7-19).

Fitting the Splashback (optional)

Position the splashback on the rear of the hotplate and secure with the screws supplied.

Customer Care

Installer: Please complete your details in this guide, inform the user how to operate the cooker and hand over the instructions.

Thank you.

Page 35

WARNING – SERVICING TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON

Art No 215-0028 - Handrail fascia fixings

Disconnect from electricity and gas before servicing. Check appliance is safe when you have nished.

8. Conversion to LP Gas

Conversion from Natural Gas (1.0 kPa) to LPG X Propane (2.54 kPa)

This conversion must be performed by a competent



person, in accordance with these instructions and with the local supply company requirements. Read the instructions before converting this appliance.

Failure to convert the appliance correctly could



invalidate any warranty or liability claims and lead to prosecution.

The conversion instructions must be used in



conjunction with the rest of the appliance instruction, in particular for information on Standards, cooker positioning, connection, hose suitability, etc.

When servicing or replacing gas-carrying



components, disconnect from the gas before starting, and check that the appliance is gas sound after completion.

DO NOT use reconditioned or unauthorised gas



controls.

Disconnect from the electricity supply before



conversion. Before electrical reconnection, check that the appliance is electrically safe.

ArtNo.311-0010 Injectors

A – Jet, B – Internal injector, C – External injector

Fig.8-1

Fig.8-2

Fig.8-3

Injectors

Remove the burner caps and heads. Remove the old jets. Fit the new jets: see ‘Technical Data’ section for correct jets. Reassemble in the reverse order (Fig.8-1).

Tap Adjustment

Removing the Handrail

Remove the handrail. Now remove the 2 cross-headed screws hidden behind the handrail end brackets (Fig.8-2).

Removing the Control Panel

Pull o all the control knobs and remove the 3 xing screws underneath the control panel (Fig.8-3).

The control panel will drop down slightly. It is held at the top by two holes in the top edge, one at each end, that locate on the tags on the inner panel. Lift the control panel clear of the tags and pull forwards, taking care not to damage or strain the wiring.

Bypass Screw Adjustment

Turn the bypass screw on each control clockwise to the stop (Fig.8-4). Ret the control panel.

ArtNo.270-0032 - 90 Prof+ FX - Removing the control panel

Control panel may dier from that shown

Fig.8-4

ArtNo.0102-0011 - Screwing

the control valve bypass screw

Page 36

WARNING – SERVICING TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON

ArtNo.103-0006 - Maxitrol cap & converter

Nut

Snap-in converter device

Disconnect from electricity and gas before servicing. Check appliance is safe when you have nished.

Fig.8-5

Fig.8-6

ArtNo.102-0007 - Maxitrol converter device positions

Set the Governor

Unscrew the governor’s brass top. In the base of the brass top is a plastic snap-in converter device (Fig.8-5). To convert the governor, snap the device out of the top and ret it the other way round. The snap-in converter device is marked to show the gas for which it is set (Fig.8-6).

Make sure the device is secure in the top cap and ret the cap to the governor.

Pressure Testing

The pressure test point is accessible on the inlet pipe at the rear. Remove the test nipple screw and t a pressure gauge to the test point. Turn on and light two of the hotplate burners.

For Propane X cookers the pressure should be 2.54 kPa.

Make sure that the appliance is gas sound.



Check the operation of all the burners.



Affix Label

Stick the appropriate gas label over the natural gas part of the appliance data label.

Page 37

WARNING – SERVICING TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON

Art No 215-0028 - Handrail fascia fixings

ArtNo.210-0009 - Classic removing the handles

Disconnect from electricity and gas supplies before servicing. Check appliance is safe when you have nished.

9. Servicing

BEFORE SERVICING ANY GAS CARRYING



COMPONENTS TURN OFF THE GAS SUPPLY

Check the appliance is gas sound after completion



of service. When checking for gas leaks DO NOT use washing up liquid – this can corrode. Use a product specically manufactured for leak detection.

DO NOT use reconditioned or unauthorised gas



controls.

Disconnect from the electricity supply before



servicing, particularly before removing any of the following: control panel, side panels, hotplate tray or any electrical components or covers.

Before electrical reconnection, check that the



appliance is electrically safe.

1 Panels & Handrails

1.1 To Remove the Handrail

Remove the plastic blanking plugs (Fig.9-1) and remove the 2 end bracket xing screws.

Fig.9-1

Fig.9-2

1.2 To Remove the Control Panel

DISCONNECT FROM THE ELECTRICITY SUPPLY.

Remove the control knobs. Remove the handrail (see

1.1). Now remove the 2 cross-headed screws hidden behind

the handrail end brackets (Fig.9-2). Pull o all the control knobs and remove the xing

screws underneath the control panel. Lift the control panel and pull forwards, taking care not

to damage or strain the wiring.

1.3 To Remove a Side Panel

DISCONNECT FROM THE ELECTRICITY SUPPLY.

Remove the control panel (see 1.2). Pull the cooker forward. Remove the 4 retaining screws from each panel (2 at the front and 2 at the rear). The lower front retaining screws (one each side) are situated beneath the lower edge at the front corners of the side panels

Reassemble in reverse order.

Page 38

WARNING – SERVICING TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON

Disconnect from electricity and gas supplies before servicing. Check appliance is safe when you have nished.

Fig.9-3

Fig.9-4

Standard burner

ArtNo.311-0010 Injectors

A – Injector, B – Internal injector, C – External injector

2 Hotplate

2.1 To Remove the Hotplate Top

DISCONNECT FROM THE ELECTRICITY SUPPLY.

Caution

The ceramic hob material is much more sensitive to scratches on the underside than the top.

Take care not to touch or scratch the underside of the ceramic as this will weaken the material and cause the top to shatter.

Remove the pan supports, hotplate burner caps and tops. Remove the screws holding the hotplate burners to the hotplate (Fig.9-3).

Taking care not to damage the burner electrodes, carefully lift the hotplate, from underneath disconnect the earth lead at the right hand rear from the rear cross member and withdraw the hotplate.

Reassemble in reverse order ensuring that the leads are reconnected. Take care not to damage the ignition electrodes of the burners.

It is important that the rear earthing leads are replaced when the xing screws are retted as they from part of the cooker earthing.

Check for correct burner operation.

2.2 To Change a Hotplate Tap

DISCONNECT FROM THE ELECTRICITY SUPPLY.

Remove the control panel and hotplate (see 1.2 & 2.1). Unplug the FSD lead from the rear of the tap. Undo

compression tting at the rear of the tap. Remove the xings that secure the tap to the gas rail. Disconnect the ignition switch wiring.

Remove the tap. Remove and discard the gasket seal. Fit new gasket seal to replacement tap. Re-assemble in reverse order. Check the appliance is gas sound. Check hotplate ignition.

2.3 To Replace a Hotplate Burner Injector

DISCONNECT FROM THE ELECTRICITY SUPPLY.

Remove the burner cap and head (Fig.9-4). Remove the old injector. Fit the new injector.

Note: The wok burner has 2 injectors. Reassemble in reverse order. Check that the appliance is

gas sound.

2.4 To Change a Hotplate Burner Electrode

DISCONNECT FROM THE ELECTRICITY SUPPLY.

Lift o the pan supports and remove the burner cap. Remove the screw holding the electrode. Pull the electrode vertically up suciently to grip the lead between thumb and forenger. Pull o the electrode, but keep hold of the lead.

Fit the new electrode to the lead. Fix the electrode in the burner with the screw.

Page 39

WARNING – SERVICING TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON

Disconnect from electricity and gas supplies before servicing. Check appliance is safe when you have nished.

Replace the burner cap. Check the burner ignition. Replace the pan supports.

2.5 To Change a Hotplate Burner Thermocouple

DISCONNECT FROM THE ELECTRICITY SUPPLY.

Remove the control panel and hotplate (see 1.2 & 2.1). Unplug the FSD lead from the rear of the tap. The thermocouple sits in a hole that has a slot at one

side. Ensure that the thermocouple is cool. Turn the thermocouple so that the earth lead (no sleeve) is in line with the slot. Lift the thermocouple clear of the hole.

Reassemble in reverse order.

2.6 To Remove or Change a Hotplate Burner

DISCONNECT FROM THE ELECTRICITY SUPPLY.

Remove the hotplate top (see 2.1). Remove the control panel (see 1.2).

The burners except the right hand wok burner are mounted on support struts. For these burners, disconnect the burner feed pipes at the burner. Remove the screws at the front and rear holding the support struts. Lift the strut and burners clear. The burners are xed to the support struts with 2 screws. Remove the appropriate burner and t the new one. Reassemble in reverse order. Check burner operation is satisfactory.

Right hand Wok burner

Disconnect the burner feed pipes at the burner. Fit the new one and reassemble in reverse order. Check burner operation is satisfactory.

3 Control

3.1 To Change the Ignition Generator

DISCONNECT FROM THE ELECTRICITY SUPPLY.

Change the hotplate tap as detailed in 2.2

3.2 To Replace the Light Switch

DISCONNECT FROM THE ELECTRICITY SUPPLY.

Remove the control panel (see 1.2). Note: The old switch may be destroyed during removal. Remove the old switch from its bezel by gripping the

switch body behind the control panel and twisting sharply. Remove the switch bezel by folding back its locking wings and pushing forward.

Fit the new bezel to the control panel by rst lining up the raised key on its body with the cut-out in the control panel and pushing it in from the front.

Assemble the new switch to the bezel by lining up the key sections and pushing home. Fit the new button by pushing in from the front.

Replace the control panel in reverse order and test for correct operation.

3.3 To Remove the Electronic Timer

DISCONNECT FROM THE ELECTRICITY SUPPLY.

Pull o the timer control button(s) and remove the control panel (see 1.2).

Remove the timer/mounting bracket assembly from the control panel by removing the xing screws.

Remove the timer from its mounting bracket by depressing the plastic lugs on the timer case, at the same time pulling the unit forward.

Reassemble in reverse order. When replacing the leads, refer to the wiring diagram in this manual. Check the operation of the timer.

4 Grill

4.1 To Replace the Grill or Ceramic Hob Controller

DISCONNECT FROM THE ELECTRICITY SUPPLY.

Remove the control panel (see 1.2) and hotplate top (see 2.1). Disconnect the wiring from the controller. Remove the 2 screws holding the controller to the mounting panel.

Fit the new controller and reassemble in reverse order. Check for correct operation.

4.2 To Remove the Grill Element

DISCONNECT FROM THE ELECTRICITY SUPPLY.

Remove grill pan from inside the grill compartment; remove the enamelled front shield from the grill roof, by removing the 2 screws and washers.

Remove the 2 screws and washers securing the grill element front support. Remove the screws from the grill element.

Lift the element out carefully, disconnecting the leads from the element terminals (noting their position).

If it is not possible to disconnect the leads in this way, pull the cooker forward to gain access to the rear, remove the screws securing the electric cover to the back sheet, remove the cover and disconnect the terminals from the rear.

Fit the new element and reassemble in reverse order. Check the operation of the grill.

Page 40

WARNING – SERVICING TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON

Disconnect from electricity and gas supplies before servicing. Check appliance is safe when you have nished.

Fig.9-5

Fig.9-6

ArtNo.320-0020 Oven back fixing screws

Thermostat capilary

Earthing plate

5 Ovens

5.1 To Replace an Oven Thermostat

DISCONNECT FROM THE ELECTRICITY SUPPLY.

Remove the handrail (see 1.1), control panel (see 1.2) and hotplate top (see 2.1). Open the oven doors and remove the oven furniture.

Left-hand oven

From inside the oven remove the two screws holding the thermostat phial to the oven fan cover at the rear of the oven.

Remove the four screws that secure the fan cover (Fig.9-5) then remove the fan cover.

Pull cooker forward to gain access to the cover box at the rear of the cooker. Remove the screws securing the cover and lift clear. The oven thermostat capillary is clamped to the oven back sheet with an earthing plate. Remove the screws and plate (Fig.9-6).

Remove the two screws securing the thermostat body to the control panel at the front of the cooker. Remove the assembly.

Fit new thermostat. Reassemble in reverse order.

Ensure that the phial is clipped to the oven back with the phial centrally positioned between the clips.

Ensure that the thermostat capillary is clamped to the oven back sheet with an earthing plate.

Check operation of thermostat.

Right-hand oven

From inside the oven remove the two screws holding the thermostat phial to the oven fan cover at the rear of the oven.

Remove the four screws that secure the fan cover (Fig.9-5) then remove the fan cover.

The oven thermostat capillary is clamped to the right hand rear upright with an earthing plate (Fig.9-6). Remove the screws and plate.

Feed the thermostat capillary out of the oven. Disconnect wiring from thermostat. Remove the two screws holding thermostat to mounting panel. Fit new thermostat and reassemble in reverse order.

Ensure that the phial is clipped to the oven back with the phial centrally positioned between the clips.

Ensure that the thermostat capillary is clamped to the right hand rear upright with an earthing plate.

Check operation of thermostat.

Page 41

WARNING – SERVICING TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON

Disconnect from electricity and gas supplies before servicing. Check appliance is safe when you have nished.

5.2 To Remove an Oven Element Thermal Cut-out

DISCONNECT FROM THE ELECTRICITY SUPPLY.

Pull the cooker forward to gain access to the cover box. Undo the cover screws and lift clear. The cut-out is located on the earth plate beside the oven element connections. Disconnect the cut-out wiring. Undo the xings that secure the cut-out to the earth plate and remove.

Fit the replacement control and reassemble in reverse order.

5.3 To Remove an Oven Inner Back

DISCONNECT FROM THE ELECTRICITY SUPPLY.

Open the door and remove the shelves. Remove the screws and washers securing the inner back to the back of the oven (Fig.9-5). Carefully lift away the inner back.

Reassemble in reverse order making sure that the screws and washers are fully tightened.

5.4 To Remove an Oven Element

DISCONNECT FROM THE ELECTRICITY SUPPLY.

Remove the oven inner back (see 5.3). Remove the 2 screws from the top of the element and the one from the bottom of the element inside the oven (Fig.9-7).

Lift the element out carefully, disconnecting the terminals connected to the element (noting their positions).

If it is not possible to disconnect the leads in this way, pull the cooker forward to gain access to the rear.

Remove the screws securing the electric cover to the back sheet, remove the cover and disconnect the terminals from the rear.

Fig.9-7

Element xing screws

ArtNo.321-0005 Fan oven element

5.5 To Replace an Oven Fan

DISCONNECT FROM THE ELECTRICITY SUPPLY.

Pull the cooker forward to gain access to the rear. Remove the screws securing the electric cover to the back sheet and remove the cover.

Disconnect the 3 terminals connected to the fan noting their position. Remove the oven inner back (see 5.3). Hold the fan blade and remove the centre nut (left-hand thread) 2 brass washers, fan blade and circlip. Unscrew the fan retaining nuts and washers (3 o each) and lift the fan away from the rear of the cooker.

Fit the new fan and reassemble in reverse order. Check the operation of the oven.

Page 42

WARNING – SERVICING TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON

ArtNo.320-0001 Door hinges



ArtNo.320-0001 Door hinges



ArtNo.322-0002 Oven bottom element access

B B

Disconnect from electricity and gas supplies before servicing. Check appliance is safe when you have nished.

Fig.9-8

Fig.9-9 Fig.9-10

Fig.9-11

Centreline of hinge pin

5.6 To Remove the Left-hand Oven Bottom and Top Elements

DISCONNECT FROM THE ELECTRICITY SUPPLY.

Bottom Element

Pull the cooker forward to access the cover boxes at the rear of the unit. Remove the xings that secure the cover and lift it clear.

Remove the 2 screws ‘A’ and allow the plate to drop down (Fig.9-8). Remove the 2 screws ‘B’ lower the upper plate and remove through the slot in the range back (Fig.9-8). Undo the terminal connections, noting their positions. Withdraw the element.

Remove the element screws and withdraw element. Replace the element and re-assemble parts in reverse order.

Top Element

Open the left-hand oven door and undo the xings that secure the heat shield. Remove the top element bracket xings and withdraw the element.

Replace the element and reassemble parts in reverse order. Check that the oven operates satisfactorily.

ArtNo.320-0007 Oven door hinge adjustment 2

Oven door omitted for clarity

Fig.9-12

ArtNo.320-0006 Oven door hinge adjustment 1

Eect of hinge adjustment – exagerrated for clarity

6 Doors

6.1 To Remove the Grill Door

Remove the left-hand side panel (see 1.3). Remove the plinth (4 screws) and the central vertical cover (5screws). Remove the 2 countersunk screws (1 each side) securing the grill hinge arms to the front of the grill chamber.

Note: The arms are spring tensioned. Carefully remove the grill door. Retain the gaskets.

Reassemble in the reverse order, making sure that the gasket is tted between the hinge arm and the front of the grill chamber.

6.2 To Replace the Main Oven Door

Open the oven door. Support the door and loosen the 2 screws securing the upper hinge and gasket to the cooker front (Fig.9-9).

The door is heavy, so take care.



Support the door and remove the screw nearest the hinge pin (Fig.9-10). Swing the hinge up and away from the door hinge pin. Lift the door away from the lower hinge and remove.

Reassemble in reverse order.

6.3 To Adjust the Main Oven Door Angle

The bottom hinge of either oven door can be adjusted to alter the angle of the door (Fig.9-11). Loosen the bottom hinge xing screws and use the notch and a at bladed screwdriver to move the position of the hinge to set the hinge position (Fig.9-12).

Retighten the hinge screws.

Page 43

WARNING – SERVICING TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON

Disconnect from electricity and gas supplies before servicing. Check appliance is safe when you have nished.

6.4 To Replace the Main Oven Door Outer Panel

Move the cooker forwards to gain access to the sides. Open the oven door slightly and remove the 4 front

panel xing screws from the door sides (2 each side), (Fig.9-13). Carefully lift o the outer door panel.

Remove the door handle from the panel by unscrewing the 2 retaining nuts.

Fit the door handle to the new panel. Fit the panel to the door. Reassemble in reverse order.

6.5 To Change the Oven Door Latch

Remove the main oven door outer panel (see 6.4). Remove screws ‘B’, which hold the latch assembly to the inner door panel (Fig.9-14). Fit the new catch and reassemble in reverse order. Check the door operation.

6.6 To Adjust the Oven Door Catch Keep

Open the oven door, slacken o the locknut at the base of the keep, and screw in or out as required until the required t is obtained. Retighten the locking nut

(Fig.9-15).

6.7 To Change an Oven Door Seal

Open the oven door. The seal is held in place by small hooks on the rear face. At the corner, pull the seal diagonally away from the door centre until that hook is released (Fig.9-16). Proceed to the next hook and release it in a similar way, and so on. Use force if the hooks are sti, as the old seal will be discarded.

When tting the new seal, position the seal join at the bottom. Hook the new seal in one of the corner holes of the door, and proceed round the door, snapping in each hook in turn.

Fig.9-14

ArtNo.320-0003 Oven door latch

Fig.9-13

ArtNo.320-0002c

- Oven door side screws (Elan)

Fig.9-15

ArtNo.320-0004 Oven door keep

Fig.9-16

6.8 Oven Door Glass

The glass on the oven doors is not replaceable.

Page 44

10. Circuit Diagram

P095199

b a

P038434

bbbb

1.1kW

P095199

B1a

B4 B5

Key

The connections shown in the circuit diagram are for single-phase. The ratings are for 230 V 50 Hz.

Code Description

A1 Grill front switch A2 Grill control A3 Grill element left-hand side A4 Grill element right-hand side B1 Left-hand oven thermostat

B1a Left-hand thermostat switch

B2 Left-hand oven control B3 Left-hand oven base element B4 Left-hand oven top element B5 Left-hand oven browning element B6 Left-hand fan element B7 Left-hand oven fan

C Clock

Code Description

D1 Right-hand fan oven thermostat D2 Right-hand fan oven control D3 Right-hand fan oven element D4 Right-hand fan oven fan F1 Ignition switch F2 Ignition spark generator G1 Ceramic hob control G2 Ceramic element G3 Ceramic element H1 Light switch H2 Oven light

I Thermal cut-out J Neon

K Cooling fan

Code Colour

b Blue

br Brown

bk Black

or Orange

r Red v Violet w White

y Yellow

g/y Green/yellow

gr Grey

Page 45

11. Technical Data

DocNo.107-0023 - Technical data - 110DF - Classic DL

This cooker is designed for use on Natural gas, although a

conversion for LP (

LPG X Propane (2.54 kPa)

) gas is packed with the

cooker.

INSTALLER: Please leave these instructions with the user.

DATA BADGE LOCATION: Cooker back. The serial number is repeated on the badge below the left-hand oven door opening.

COUNTRY OF DESTINATION: Australia.

Connection & Test Pressures

Gas (Rp ½ at rear right-hand side) Electric

Natural gas 1 kPa Propane 2.54 kPa

220-240 V 50 Hz

See the appliance badge for test pressures.

Dimensions Refer to ‘Positioning the Cooker’.

Overall height minimum 905 mm maximum 930 mm Overall width 1100 mm Overall depth 611 mm to fascia; 668 mm over handles Minimum space above hotplate 650 mm

Ratings

Hotplate

Bypass Screw*

Input

Wok burner 55 15.2 MJh

Large burner 41 12.3 MJh Medium burner 33 6.2 MJh Small burner 25 3.7 MJh

Natural Gas 1.0 kPa Propane 2.54 kPa

Injector

Marking Size Ø Marking Size Ø

internal 88 0.88 mm

-1

external 168 1.68 mm external 98 0.98 mm

-1

165 1.65 mm 12.0 MJh 115 1.15 mm 6.2 MJh

92 0.92 mm 3.3 MJh

Input

15.0 MJh

internal 57 0.57 mm

-1

Injector

89 0.96 mm 67 0.68 mm 48 0.50 mm

Ceramic Hob Front element Rear element

Power rating 1.1 kW 1.1 kW

* The valves in this cooker are fitted with adjustable bypass screws. The cooker is supplied with the bypass screws set for Natural gas. For LPG conversion the bypass screws must be screwed all the way down.

Oven Efficiencies

Ovens

Maximum power output @ 230 V 50 Hz 3.7 kW 2.5 kW Energy eciency class on a scale of A (more ecient) to G (less ecient) A A Energy consumption based on standard load 0.95kWh 0.90kWh

Usable volume (litres) 69 69 Size Large Large Time to cook standard load 41 minutes 41 minutes Surface area of the grid 1400cm

Grill 2.3 kW

Maximum total electrical load at 230 V (approximate total including oven lights, oven fan, etc.): 10.8 kW.

Left-hand Oven Right-hand Oven

Multi-function Forced Air Convection

1400cm

Page 46

Notes

Page 47

Notes

Page 48

Clarence Street, Royal Leamington Spa,

Warwickshire, CV31 2AD, England.

Tel: +44 (0) 1926 457400 Fax: +44 (0) 1926 450526

E-mail: consumers@falconappliances.co.uk

Falcon CDL110DFCY-CHLPG, CDL110DFBL-CHLPG, CDL110DFBL-CH, CDL110DFBL-BR, CDL110DFCR-CH Installation and Operation Guide

Specifications and Main Features

Frequently Asked Questions

User Manual