Page 1
USER GUIDE &
INSTALLATION INSTRUCTIONS
900 Deluxe Induction G5
Page 2
SLOW BAKED LEG OF LAMB
INGREDIENTS
¥ 2Ð3 large sprigs of rosemary
¥ 4 large garlic cloves cut in half lengthways
¥ 1.8 kg leg of lamb
¥ 8 good quality anchovy fillets, halved
¥ 100 ml olive oil
¥ 250 ml dry red wine
¥ Maldon salt and freshly ground black pepper
METHOD
1. Preheat the oven to 220 ¡C (for a conventional oven), 200 ¡C
(for a fan oven) or gas mark 7.
2. Pull the small sprigs off the rosemary branches and set aside
with the garlic.
2. Using the tip of a paring knife, make up to 20 well-spaced
cuts into the flesh of the lamb, about 2.5 cm inch deep.
Divide the rosemary sprigs, garlic and anchovies and push
down into the cuts. Place the leg on a large roasting tin and
pour over the oil, massaging it all over the joint. Season well
with salt and pepper and pour the wine and 250 ml water
into the tin.
3. Put into the oven and sear for 15 minutes, then turn the
temperature right down to 130 ¡C (conventional oven),
110 ¡C (fan oven) or gas mark 1 and roast for 4Ð5 hours,
basting every 30 minutes or so. Basting frequently helps
to keep the meat moist and encourages the build up of a
good glaze on the outside. Add more liquid (wine or water)
if the tin looks dry Ð there should always be liquid in the tin
throughout this cooking process.
4. The meat is ready when it starts to fall off the bone, at which
point it should have a core temperature of 90 ¡C. Remove
from the oven, transfer to a warmed carving dish, cover
loosely with foil and leave to rest in a warm place for 30Ð45
minutes before carving.
5. Pour the juices from the tin into a tall hi-ball glass and allow
to settle. Spoon the fat from the top of the glass. There
should be enough sticky, reduced juices for an intense gravy
hit Ð if not, pour the juices you have back into the roasting
tin and put it over the heat, pour in a splash of water or wine
and deglaze the tin scraping up all the sticky bits from the
base. Boil fast until syrupy, taste and correct the seasoning.
RASPBERRY SOUFFLă
INGREDIENTS
¥ 400 g raspberries
¥ 1 tbsp lemon juice
¥ 100 g caster sugar
¥ 2 tsp cr�me de framboise
¥ 1 tsp cornflour
¥ 180 g egg whites (about 6)
¥ Pinch of cream of tartar or a squeeze of lemon juice
¥ Icing sugar for dusting
METHOD
1. For the soufflŽ, press the raspberries through a fine
sieve to produce 180 g of purŽe. Put this into a heavybottomed pan, add the lemon juice and reduce down to
a thick jam, stirring from time to time and being careful
not to let it catch and burn.
2. Put 45 g of the sugar in a separate pan. Melt it and then
boil until it becomes a thick syrup (121 ¡C on a sugar
thermometer). To test without a thermometer, dip a
teaspoon into the syrup and then dip quickly into cold
water. You should be able to roll the cooling syrup into
a ball between your fingers. Be careful as the syrup is
extremely hot. When it has reached the right point, stir
the hot syrup into the raspberry jam.
3. Mix the framboise and cornflour together and stir into
the jam over the heat. Turn the jam into a small bowl,
sprinkle the surface with icing sugar and cover with cling
film.
4. Preheat the oven (not grill) to 180 ¡C shelf level 2
(conventional oven), 160 ¡C (fan oven) or gas mark 4
centre shelf.
5. Whisk the egg whites with the cream of tartar until you
can form soft peaks, then fold in the remaining caster
sugar. Lightly fold the whites into the jam, leaving thin
traces of white visible in the mixture.
6. Spoon into four large buttered and sugared ramekins,
place these on a baking tray and bake for 10 minutes.
7. Dust with icing sugar.
Page 3
Contents
1. Before You Start... 1
Installation and Maintenance 1
Peculiar Smells 1
Ventilation 1
Personal Safety 1
Hob Care 3
Cooker Care 3
2. Overview 4
The Hob 4
Operating the Oven 9
Accessories 9
3. Cooking Tips 10
Using Your Induction Cooker 10
General Oven Tips 10
4. Cooking Table 11
5. Cleaning Your Cooker 12
Hob 12
Glide-out Grill 13
Control Panel and Oven Doors 14
Ovens 14
The Tall Oven 14
Cleaning Table 15
6. Troubleshooting 16
7. Installation 18
Dear Installer 18
Safety Requirements and Regulations 18
Provision of Ventilation 18
Location of Cooker 18
Positioning the Cooker 19
Moving the Cooker 19
Fitting the Stability Bracket 20
Repositioning the Cooker Following
Connection
Levelling 20
Electrical Connection 21
Final Checks 21
Fitting the Plinth 21
Customer Care 21
20
8. Circuit Diagrams 22
Circuit Diagram: Hob 22
Circuit Diagram: Oven 23
9. Technical Data 24
10. Warranty/After Sales Service 25
If You Have a Problem 25
Notes 25
Out of Warranty 25
Spare Parts 25
i
U110270-02Falcon 900 Deluxe Induction G5
Page 4
ii
Page 5
1. Before You Start...
Thank you for buying this cooker. It should give you many
years of trouble-free cooking if installed and operated
correctly. It is important that you read this section before you
start, particularly if you have not used an induction cooker
before.
This appliance is designed for domestic cooking
only. Using it for any other purpose could invalidate
any warranty or liability claim. In particular, the
oven should NOT be used for heating the kitchen –
besides invalidating claims this wastes fuel and may
overheat the control knobs.
Installation and Maintenance
All installations must be in accordance with the relevant
instructions in this booklet, with the relevant national
and local regulations, and with the local electricity supply
companies’ requirements.
Make sure that the cooker is correctly wired and switched on.
The hob control display will ash for about 2 seconds
during the rst power setting – this is normal.
Only a qualied service engineer should service the cooker,
and only approved spare parts should be used.
Always allow the cooker to cool and then switch it o at the
mains before cleaning or carrying out any maintenance work,
unless specied otherwise in this guide.
Peculiar Smells
When you rst use your cooker it may give o an odour. This
should stop after use.
Before using your cooker for the rst time, make sure that all
packing materials have been removed and then, to dispel
manufacturing odours, turn all the ovens to 200 °C and run
for at least an hour.
Before using the grill for the rst time you should also turn on
the grill and run for 30 minutes with the grill pan in position,
pushed fully back, and the grill door open.
Make sure the room is well ventilated to the outside air
(see ‘Ventilation’ below). People with respiratory or allergy
problems should vacate the area for this brief period.
Ventilation
CAUTION: The use of a cooking appliance results in
the production of heat and moisture in the room in
which it is installed. Therefore, make sure that the
kitchen is well ventilated: keep natural ventilation
holes open or install a powered cookerhood that
vents outside. If you have several hotplates on, or
use the cooker for a long time, open a window or
turn on an extractor fan.
Personal Safety
Important information for pacemaker and implanted
insulin pump users: The functions of this hob comply with
the applicable European standards on electromagnetic
interference. If you are tted with a pacemaker or
implanted insulin pump and are concerned please consult
your doctor for medical advice.
DO NOT modify this appliance.
This appliance can be used by children aged from
8years and above and persons with reduced
physical, sensory or mental capabilities or lack of
experience and knowledge if they have been given
supervision or instruction concerning use of the
appliance in a safe way and understand the hazards
involved. Children shall not play with the appliance.
Cleaning and user maintenance shall not be made by
children without supervision.
WARNING!
The appliance and its accessible parts become
hot during use and will retain heat even after you
have stopped cooking. Care should be taken to
avoid touching heating elements. Children less
than 8years of age shall be kept away unless
continuously supervised.
When the hob is in use keep magnetic items, such as
credit and debit cards, oppy disk, calculators, etc.
away.
CAUTION: A long term cooking process has to be
supervised from time to time. A short term cooking
process has to be supervised continuously.
Danger of re: DO NOT store items on the cooking
surfaces.
To avoid overheating, DO NOT install the cooker
behind a decorative door.
Accessible parts will become hot during use and will
retain heat even after you have stopped cooking.
Keep babies and children away from the cooker and
never wear loose-tting or hanging clothes when
using the appliance.
DO NOT use a steam cleaner on your cooker.
Always be certain that the controls are in the OFF position
when the oven is not in use, and before attempting to clean
the cooker.
Take care when touching the marked cooking areas
of the hob.
When the oven is on, DO NOT leave the oven door
open for longer than necessary, otherwise the
control knobs may become very hot.
When using the grill, make sure that the grill pan
is in position and pushed fully in, otherwise the
control knobs may become very hot.
1
Page 6
ArtNo.312-0001 Not cooking surface
Fig.1-1
ArtNo.324-0001 Steam burst
Always keep combustible materials, e.g. curtains, and
ammable liquids a safe distance away from your cooker.
DO NOT spray aerosols in the vicinity of the cooker
while it is on.
Cooking high moisture content foods can create a ‘steam
burst’ when an oven door is opened (Fig.1-1). When opening
an oven stand well back and allow any steam to disperse.
Use dry oven gloves when applicable – using damp gloves
might result in steam burns when you touch a hot surface.
Do not use a towel or other bulky cloth in place of a glove – it
might catch re if brought into contact with a hot surface.
Fig.1-2
NEVER operate the cooker with wet hands.
DO NOT use aluminium foil to cover shelves, linings,
the oven roof or the oven base.
NEVER heat unopened food containers. Pressure
build up may make the containers burst and cause
injury.
DO NOT use unstable saucepans. Always make sure
that you position the handles away from the edge of
the hotplate.
Never leave the hotplate unattended at high heat settings.
Pans boiling over can cause smoking, and greasy spills may
catch on re. Use a deep fat thermometer whenever possible
to prevent fat overheating beyond the smoking point.
WARNING!
Unattended cooking on a hob with fat or oil can be
dangerous and may result in re.
NEVER leave a chip pan unattended. Always heat fat
slowly, and watch as it heats. Deep fry pans should
be only one third full of fat. Filling the pan too full
of fat can cause spill over when food is added. If you
use a combination of oils or fats in frying, stir them
together before heating, or as the fats melt.
Foods for frying should be as dry as possible. Frost on frozen
foods or moisture on fresh foods can cause hot fat to bubble
up and over the sides of the pan. Carefully watch for spills or
overheating of foods when frying at high or medium high
temperatures. Never try to move a pan of hot fat, especially a
deep fat fryer. Wait until the fat is cool.
Do not use the top of the ue (the slots along the back of
the cooker) for warming plates, dishes, drying tea towels or
softening butter.
DO NOT use water on grease res and never pick
up a aming pan. Turn o the controls and then
smother a aming pan on a surface unit by covering
the pan completely with a well tting lid or baking
tray. If available, use a multi-purpose dry chemical
or foam-type re extinguisher.
Take care that no water seeps into the appliance.
This appliance is heavy so take care when moving it.
NEVER allow anyone to climb or stand on the hob.
2
Page 7
Hob Care
ArtNo.312-0003 Moving pans
NEVER cook directly on the hob surface (Fig.1-2).
DO NOT use the hob surface as a cutting board.
DO NOT leave utensils, foodstus or combustible items on
the hob when it is not is use (e.g. tea towels, frying pans
containing oil).
DO NOT place plastic or aluminium foil, or plastic
containers, on the hob.
DO NOT leave the hob zones switched on unless
being used for cooking.
DO NOT stand or rest heavy objects on the hob. Although the
ceramic surface is very strong, a sharp blow or sharp falling
object (e.g. a salt cellar) might cause the surface to crack or
break (Fig.1-3).
Should a crack appear in the surface, disconnect the
appliance immediately from the supply and arrange
for its repair.
Always LIFT pans o the hob. Sliding pans may cause marks
and scratches (Fig.1-4). Always turn the control to the OFF
position before removing a pan.
Take care when placing hot lids onto the hob
surface. Lids that have been covering boiling or
steaming foods can ‘stick’ to the ceramic glass.
Should this occur, DO NOT attempt to lift the lid o
the hotplate: this may damage the hob surface.
Fig.1-3
Fig.1-4
Fig.1-5
DO NOT place anything between the base of the pan and the
hob surface (e.g. asbestos mats, aluminium foil, wok stand).
Cooker Care
As steam can condense to water droplets on the cool outer
trim of the oven, it may be necessary during cooking to wipe
away any moisture with a soft cloth. This will also help to
prevent soiling and discolouration of the oven exterior by
cooking vapours (Fig.1-5).
ArtNo.090-0007 90 Ceramic:
oven steam out the back
3
Page 8
A
B
D
C
E
2. Overview
Fig.2-1
Fig.2-2
The Falcon induction cooker (Fig.2-1) has the following
features:
A. 5 induction cooking zones
B. A control panel
C. A glide-out grill
D. Main multi-function oven
E. Tall fan oven
The Hob
Use only pans that are suitable for induction hobs. We
recommend stainless steel, enamelled steel pans or cast iron
pans with enamelled bases. Note that some stainless steel
pans are not suitable for use with an induction hob so please
check carefully before purchasing any cookware.
Pans made of copper, aluminium or ceramic are not suitable
for use on an induction hob. The kind of pan you use and the
quantity of food aects the setting required. Higher settings are
required for larger quantities of food.
Pots and pans should have thick, smooth, at bottoms
(Fig.2-2). This allows the maximum heat transfer from the
hob to the pan, making cooking quick and energy ecient.
4
Page 9
Never use a round-bottomed wok, even with a stand.
The very best pans have bases that are very slightly curved
up when cold (Fig.2-3). If you hold a ruler across the bottom
you will see a small gap in the middle. When they heat up the
metal expands and lies at on the cooking surface.
Make sure that the base of the pan is clean and dry to prevent
any residue burning onto the hob panel. This also helps
prevent scratches and deposits.
Always use pans that are the same size as (or slightly larger
than) the areas marked on the hob. Using a lid will help the
contents boil more quickly.
Always take care before touching the surface, even
when the hob is turned o. It may be hotter than you
think!
The induction hob comprises of ve cooking zones (Fig.2-4)
containing induction elements with dierent ratings and
diameters each with a pan detector and residual heat
indicator, and a hob control display.
The hob control display (Fig.2-5) informs you of the following
induction hob functions:
Pan Detector
H Residual Heat Indicator
A Automatic Heat-up
Child Lock
L1/L2 Low Temperature Setting
P Power Boost Setting
Max: 1.85 kW
Boost: 3.0 kW
Max: 1.4 kW
Boost: 2.2 kW
Max: 2.3 kW
Boost: 3.7 kW
Fig.2-3
Fig.2-4
Max: 1.85 kW
Boost: 3.0 kW
Max: 1.85 kW
Boost: 3.0 kW
Pan Detector,
IMPORTANT: After use, switch o the hob element by its
control and DO NOT RELY on the pan detector.
If a cooking area is switched on and there is no pan in place
or if the pan is too small for the cooking area, then no heat
will be generated. The symbol [ ] will appear on the hob
control display; this is the “pan-missing symbol”. Place a pan
of the correct size on the cooking area and the [ ] symbol
will disappear and cooking can begin. After 10 minutes
without detecting a pan the cooking zone will switch o
automatically.
Table 2-1 shows the minimum pan sizes recommended for
each cooking zone.
Note: Using pans with a base diameter smaller than those
recommended will result in a power reduction.
Residual Heat Indicator, H
After use, a cooking zone will remain hot for a while as heat
dissipates. When a cooking zone is switched o the residual
heat indicator symbol [H ], will appear in the display. This
shows that the cooking zone temperature is above 60 °C and
may still cause burns. Once the temperature has dropped to
below 60 °C the [H ] will go out.
Cooking Zone
Front left
Rear left
Centre
Rear right
ArtNo.051-0002 - Min pan diameter
Front right
Fig.2-5
Minimum Pan Diameter
(Pan Base) mm
140
180
180
180
140
Table 2-1
5
Page 10
Fig.2-6
ArtNo.051-0002 - Min pan diameter
Power Level
Maximum Operating Time
2 hours
6 hours
6 hours
5 hours
5 hours
4 hours
1.5 hours
1.5 hours
1.5 hours
1.5 hours
10 minutes
L1 and L2
1
2
3
4
5
6
7
8
9
Power Boost
Power Level
Automatic Heat-up Time at
1 0:48
2 2:24
3 3:50
4 5:12
5 6:48
6 2:00
7 2:48
8 3:36
9
Table 2-2
100% (min:sec)
Automatic Heat-up, A
This function is available on all of the cooking areas. It
allows rapid heating up of the element to bring the selected
cooking zone up to temperature. Once the zone is at the
required cooking temperature the power level will reduce
automatically to the preset level.
The function is selected by turning the control knob to the
‘A’ position. This can be selected by either turning the control
knob momentarily counter-clockwise from the zero position
or clockwise past the ‘9’ until the symbol [A ] is shown on
the hob control display. Once the [A ] is displayed, turn the
control knob to the level of your choice (1 to 9). The pan will
heat up at 100% power for a specied time before the power
is reduced to the level selected.
When the Automatic Heat-up function is activated, the hob
control display will alternately ash between the [A ] setting
and the chosen power level.
Once the Automatic Heat-up time has ended the hob control
display will stop ashing and will display the chosen power
level. The Automatic Heat-up function can be stopped by
either turning the control knob back to the ‘0’ power setting
or turning the control knob to the ‘9’ power setting. For your
guidance Table 2-2 shows the time available at 100% power
depending on the power level selected in the Automatic
Heat-up mode.
Fig.2-7
Table 2-3
Child Lock,
IMPORTANT: The child lock can only be activated when all
the cooking zones are switched o.
To prevent the unwanted use by children, the hob can be
locked.
To lock the hob, simultaneously turn the two left-hand hob
controls counter-clockwise (Fig.2-6) and hold until the
symbol appears in the centre of the hob control display
(Fig.2-7).
Note: [A ] will ash when locking the hob – this is normal.
Locking the hob will NOT aect the oven; it can still be used.
To unlock the hob, simultaneously turn the two left-hand hob
controls counter-clockwise and hold until the
symbol
disappears from the centre of the hob control display.
Low Temperature Setting, L1/L2
Each cooking area is equipped with 2 low temperature
settings:
• L1 will maintain a temperature of about 40 °C – ideal for
gently melting butter or chocolate.
• L2 will maintain a temperature of about 90 °C – ideal for
simmering (bring the pan to the boil and then select L2
to keep soups, sauces, stews, etc at an optimal simmer).
The maximum time this setting can be used is 2 hours, after
which the hob will switch o automatically. If required, you
can immediately restart the Low Temperature function by
reactivating L1 or L2. To increase the heat, just turn the control
knob to the required level. The maximum times for all other
power levels are shown in Table 2-3.
6
Page 11
Power Boost Setting, P
All of the induction cooking zones have Power Boost
available, activated by turning the control knob clockwise
until [P ] is shown on the hob control display.
Power Boost allows additional power to be made available for
each of the cooking zones. This is useful to bring a large pan
of water to the boil quickly.
The Power Boost function operates for a maximum of 10
minutes on each zone, after which the power is automatically
reduced to setting 9.
When using the Power Boost function, the cooking zones are
linked.
Fig.2-8 shows the hob layout. Zones A and B are linked
together as are zones D and E.
This means that when using zone A on Power Boost and then
switching zone B to Power Boost , the power to zone A will
reduce slightly. The last zone switched to Power Boost always
takes priority. Zones D and E work in the same way.
This is a built-in safety device.
Deactivate the Power Boost function by turning the control
knob to a lower setting.
Overheat Function
This function identies when the temperature of the pan rises
rapidly and works to maintain a safe level of pan temperature.
It should not interfere with normal cooking.
Please remember not to leave the hob unattended.
Care should be taken to not allow your cookware to
boil dry.
A & B linked D & E linked
A D
B
Function Use
Defrost
Fan oven
Fanned grilling
Fan assisted
Conventional oven
Browning element
Base heat
To thaw small items in the oven without
heat
A full cooking function, even heat
throughout, great for baking
Grilling meat and fish with the door
closed
A full cooking function good for roasting
and baking
A full cooking function for roasting and
baking in the lower half of the oven
To brown and crisp cheese topped
dishes
To crisp up the bases of quiche, pizza or
pastry
Fig.2-8
C
E
Table 2-4
The Multi-function Oven
Multi-function ovens have an oven fan and oven fan element,
as well as two extra heating elements. One element is in
the top of the oven and the second is under the oven base.
Take care to avoid touching the top element and element
deector when placing or removing items from the oven.
The multi-function oven has 3 main cooking functions: fan,
fan assisted and conventional cooking. These functions
should be used to complete most of your cooking.
The browning element and base heat can be used in the
latter part of the cooking process to ne tune the results to
your particular requirements.
Use fanned grilling for all your grilling needs and defrost to
safely thaw small items of frozen food.
Table 2-4 gives a summary of the multi-function modes.
The multi-function oven has many varied uses. We suggest
you keep a careful eye on your cooking until you are familiar
with each function. Remember, not all functions will be
suitable for all food types.
7
Page 12
Multi-function Oven Functions
Fan Oven
This function operates the fan and the heating
element around it. An even heat is produced
throughout the oven, allowing you to cook large
amounts quickly.
Fan oven cooking is particularly suitable for baking on several
shelves at one time and is a good ‘all-round’ function. It may
be necessary to reduce the temperature by approximately
10 °C for recipes previously cooked in a conventional oven.
If you wish to preheat the oven, wait until the indicator light
has gone out before inserting the food.
Fanned Grilling
This function operates the fan while the top element
is on. It produces a more even, less erce heat than a
conventional grill. For best results, place the food to
be grilled, on a trivet over a roasting tin, which should be
smaller than a conventional grill pan. This allows greater air
circulation. Thick pieces of meat or sh are ideal for grilling in
this way, as the circulated air reduces the erceness of the
heat from the grill.
The oven door should be kept closed while grilling is in
progress, so saving energy.
You will also nd that the food needs to be watched and
turned less than for normal grilling. Preheat this function
before cooking.
For best results we recommend that the grill pan is not
located on the uppermost shelf.
Fan Assisted Oven
This function operates the fan, circulating air heated
by the elements at the top and the base of the oven.
The combination of fan and conventional cooking
(top and base heat) makes this function ideal for cooking
large items that need thorough cooking, such as a large meat
roast.
It is also possible to bake on two shelves at one time,
although they will need to be swapped over during the
cooking time, as the heat at the top of the oven is greater
than at the base, when using this function.
This is a fast intensive form of cooking; keep an eye on the
food cooking until you have become accustomed to this
function.
Conventional Oven (Top and Base Heat)
This function combines the heat from the top and
base elements. It is particularly suitable for roasting
and baking pastry, cakes and biscuits.
Food cooked on the top shelf will brown and crisp faster than
on the lower shelf, because the heat is greater at the top of
the oven than at the base, as in ‘Fan Assisted Oven’ function.
Similar items being cooked will need to be swapped around
for even cooking. This means that foods requiring dierent
temperatures can be cooked together, using the cooler zone
in the lower half of the oven and hotter area to the top.
The exposed top element may cook some foods too quickly,
so we recommend that the food be positioned in the lower
half of the oven to cook. The oven temperature may also need
to be lowered.
Similar items being cooked will need to be swapped around
for even cooking.
Browning Element
This function uses the element in the top of the oven
only. It is a useful function for the browning or
nishing of pasta dishes, vegetables in sauce,
shepherds pie and lasagne, the item to be browned being
already hot before switching to the top element.
Base Heat
This function uses the base element only. It will crisp
up your pizza or quiche base or nish o cooking the
base of a pastry case on a lower shelf. It is also a
gentle heat, good for slow cooking of casseroles in the
middle of the oven or for plate warming.
The Browning and Base Heat functions are useful additions
to your oven, giving you exibility to nish o items to
perfection.
Defrost
This function operates the fan to circulate cold air
only. Make sure the temperature control is at 0°C and
that no heat is applied. This enables small items such
as desserts, cream cakes and pieces of meat, sh and poultry
to be defrosted.
Defrosting in this way speeds up the process and protects
the food from ies. Pieces of meat, sh and poultry should
be placed on a shelf, over a tray to catch any drips. Be sure to
wash the shelf and tray after defrosting.
Defrost with the oven door closed.
Large items, such as whole chickens and joints should not be
defrosted in this way. We recommend this be carried out in a
refrigerator.
Defrosting should not be carried out in a warm oven or when
an adjoining oven is in use or still warm. Make sure that dairy
foods, meat and poultry are completely defrosted before
cooking.
8
Page 13
Operating the Oven
The multi-function oven has two controls: a function selector
and a temperature setting knob (Fig.2-9).
Turn the function selector control to a cooking function. This
is the fan oven setting (Fig.2-10).
Turn the oven temperature knob to the temperature you
need. The oven heating light will glow until the oven has
reached the temperature you selected. It will then cycle on
and o during cooking as the oven maintains the selected
temperature (Fig.2-11).
Your oven has many varied uses. We suggest you keep a
careful eye on your cooking until you are familiar with each
function. Remember, not all functions will be suitable for all
food types.
Accessories
Oven Shelves – Left-hand (Main) Oven
In addition to the at shelves, your cooker is supplied with a
drop shelf (Fig.2-12). The drop shelf increases the possibilities
for oven shelf spacing.
Removing and Retting the Oven Shelves
The shelf has a small kink on either side (Fig.2-13). To remove
the shelf, line these up with the stops in the shelf support
(Fig.2-14). Lift the shelf upwards so that it will pass over the
shelf stop (Fig.2-15) and then pull it forwards (Fig.2-16).
220°
ArtNo.061-0001 - 90 induction - 900S MF oven controls
Function selector Temperature selector
180°
Fig.2-10
220°
Fig.2-9
140°
Fig.2-11
180°
Fig.2-12
100°
100°
140°
Ret in the reverse order, making sure to push it fully back.
Oven Shelves – Right-hand (Tall) Oven
The tall oven is supplied with four at cooking shelves
(Fig.2-17), and a plate-warming shelf (Fig.2-18).
When using the tall oven, you can cook on all four shelves at
the same time, but make sure that they are well spaced out to
allow the hot air to circulate.
Fig.2-13 Fig.2-14
Fig.2-15 Fig.2-16
Fig.2-17 Fig.2-18
ArtNo.324-0009 Tall oven shelf
ArtNo.324-0010 Plate warming shelf
9
Page 14
3. Cooking Tips
Using Your Induction Cooker
If you have not used an induction cooker before please be
aware of the following:
• Make sure that the pans you have or buy are suitable
for use on the induction hob. Stainless steel, enamelled
steel or cast iron is ideal. Double check before you
buy pans – they must have bases that would attract a
magnet.
• Allow time to get used to induction cooking; it is fast
and powerful as well as being gentle. When simmering,
you may notice that liquids appear to stop bubbling and
then start again almost immediately. This is perfectly
normal.
• You may notice a faint vibrating sound coming from
the pans when using the induction hob. Again, this is
perfectly normal and will depend upon the type and
style of pans you are using.
• The induction heating elements will phase on and off
when cooking. Although an active cooking zone may
appear to switch on and off, a constant heat is still being
supplied to the base of the pan – this is completely
normal.
General Oven Tips
The wire shelves should always be pushed rmly to the back
of the oven.
Baking trays with food cooking on them should be placed
level with the front edge of the oven’s wire shelves. Other
containers should be placed centrally. Keep all trays and
containers away from the back of the oven, as overbrowning
of the food may occur.
For even browning, the maximum recommended size of a
baking tray is 340 mm (13½”) by 340 mm (13½”) in the main
oven and 210 mm (9
When the oven is on, do not leave the door open for
longer than necessary, otherwise the knobs may get very
hot.
• Always leave a “finger’s width” between dishes on
the same shelf. This allows the heat to circulate freely
around them.
• To reduce fat splashing when you add vegetables to hot
fat around a roast, dry them thoroughly or brush lightly
with cooking oil.
• Where dishes may boil and spill over during cooking,
place them on a baking tray.
• The ‘Cook & Clean’ oven liners (see ‘Cleaning Your
Cooker’) work better when fat splashes are avoided.
Cover meat when cooking.
• Sufficient heat rises out of the oven while cooking to
warm plates in the grill compartment.
• If you want to brown the base of a pastry dish, preheat
the baking tray for 15 minutes before placing the dish in
the centre of the tray.
1
/8”) and 285 mm (125/8”) in the tall oven.
10
Page 15
4. Cooking Table
DocNo.031-0004 - Cooking table - electric & fan single cavity
The oven control settings and cooking times given in the table below are intended to be used
AS A GUIDE ON LY. Individual tastes may require the temperature to be altered to provide a
preferred result.
Food is cooked at lower temperature in a fan oven than in a conventional oven. When using
recipes, reduce the fan oven temperature by 10 °C and the cooking time by 5-10 minutes. The
temperature in the fan oven does not vary with height in the oven so you can use any shelf.
Conventional Oven
Food
Meat
Beef (no bone)
Lamb
Pork
Poultry
Chicken
Turkey
Duck
Casserole
Yorkshire Pudding
Cake
Very rich fruit - Christmas,
wedding, etc.
Fruit 180 mm tin
Fruit 230 mm tin
Madeira 180 mm
Queen cakes
Scones
Victoria sandwich
180 mm tin
210 mm tin
Desserts
Shortcrust tarts
Fruit pies
Tartlets
Puff pastry
Meringues
Baked egg custard
Baked sponge pudding
Milk pudding
Bread
Fish
Fillet
Whole
Steak
Temperature °C
(Shelf Position)
160 (C)
200 (C)
160 (C)
200 (C)
160 (C)
200 (C)
160 (C)
200 (C)
160 (C)
200 (C)
160 (C)
200 (C)
140-150 (C)
220 (C)
140 (C/B)
150 (C/B)
150 (C/B)
160 (C/B)
190 (C/B)
220 (C/B)
180 (C/B)
180 (C/B)
200 (C/B)
200 (C/B)
200 (C/B)
210 (C/B)
100 (C/B)
160 (C/B)
180 (C/B)
140-150 (C/B)
210 (C)
Fanned Grilling
190 (C/B)
190 (C/B)
190 (C/B)
Fan Oven
Temperature
°C
150
190
150
190
150
190
150
190
150
190
150
190
130-140
210
130
140
140
150
180
210
170
170
190
190
190
200
90
150
170
130-140
200
190 (C/B)
190 (C/B)
190 (C/B)
Approximate Cooking Time
ArtNo.050-0001 Gas cooking table
30-35 minutes per 500g +30-35 minutes.
20-25 minutes per 500g +20-25 minutes.
30-35 minutes per 500g +30-35 minutes.
25-30 minutes per 500g +25-30 minutes.
35-40 minutes per 500g +35-40 minutes.
25-30 minutes per 500g +25-30 minutes.
20-25 minutes per 500g +20-25 minutes.
15-20 minutes per 500g +15-20 minutes.
20 minutes per 500g +20 minutes.
15 minutes per 500g +15 minutes.
25-30 minutes per 500g.
20 minutes per 500g.
2-4 hours according to recipe.
Large tins 30-35 minutes; individual 10-20 minutes.
45-50 minutes per 500g of mixture.
2-2½ hours.
Up to 3½ hours.
80-90 minutes.
15-25 minutes.
10-15 minutes.
20-30 minutes.
30-40 minutes.
20-30 minutes on a preheated tray.
35-45 minutes.
10-20 minutes according to size.
20-40 minutes according to size.
2-3 hours.
45-60 minutes.
40-45 minutes.
2 to 3 hours.
20-30 minutes.
15-20 minutes.
15-20 minutes per 500g.
Steaks according to thickness.
Top (T)
Centre (C)
Base (B)
ArtNo.050-0007
Oven shelf positions
Oven Shelf Positions
T - Top; C - Centre; B - Base
Thoroughly thaw frozen joints before
cooking. Meat may be roasted at
220°C (210°C for fan oven) and the
cooking time adjusted accordingly.
For stuffed and rolled meats, add
approximately 10 minutes per 500g,
or cook at 200°C (190°C) for 20
minutes then 160°C (150°C) for the
remainder.
For stuffed poultry, you could cook
at 200°C (190°C) for 20 minutes
then 160°C (150°C) for remainder.
Do not forget to include the weight
of the stuffing.
For fresh or frozen prepacked
poultry, follow instructions on the
pack. Thoroughly thaw frozen
poultry before cooking.
Using the conventional oven: when
two tier cooking leave at least one
runner space between shelves.
Position the baking tray with the
front edge along the front of the
oven shelf.
Up to three tiers can be cooked in a
fan oven at the same time but make
sure to leave at least one runner
space between each shelf being
cooked on.
Using the conventional oven: for
even browning the maximum size of
baking tray recommended is 340 mm
x 340 mm. This ensures free heat
circulation.
If cooking a two tier load, the trays
should be interchanged
approximately halfway though the
cooking time.
11
Page 16
ArtNo.312-0010 Cleaning; scraping the ceramic hob
5. Cleaning Your Cooker
Fig.5-1
Isolate the electricity supply before carrying out any major
cleaning. Allow the cooker to cool.
NEVER use paint solvents, washing soda, caustic
cleaners, biological powders, bleach, chlorine based
bleach cleaners, coarse abrasives or salt.
DO NOT mix dierent cleaning products – they may
react together with hazardous results.
Avoid using any abrasive cleaners including cream
cleaners. For best results, use a liquid detergent.
All parts of the cooker can be cleaned with hot soapy
water – but take care that no surplus water seeps
into the appliance.
Remember to switch the electricity supply back on before
reusing the cooker.
Hob
Daily Care
First of all make sure that all heat indicator lights are o and
that the cooking surface is cool. Apply a small dab of ceramic
cleaning cream in the centre of each area to be cleaned.
Dampen a clean paper towel and work the cream onto the
cooking surface. As a nal step, wipe the cooking surface with
a clean, dry paper towel.
Cleaning Spills
For spills and boil-overs that occur while cooking, turn the
unit o and wipe the area surrounding the hot zone with a
clean paper towel. If a spill (other than a sugary substance) is
on the hot zone, do not clean until the unit has completely
cooled down, and then follow the instructions below
(‘Cleaning Burned-on Spills’).
If you accidentally melt anything on the surface, or if you spill
foods with a high sugar content (preserves, tomato sauce,
fruit juice, etc.), remove the spill IMMEDIATELY with a razor
scraper, while the unit is still hot.
IMPORTANT: Use an oven glove to protect your hand from
potential burns.
Scrape the major spill or melted material from the cooking
zone and push into a cold area. Then, turn the unit ‘OFF’ and
allow it to cool before cleaning further. After the cooking
surface cools down and the heat indicator lights go o, follow
the ‘Daily Care’ procedure outlined above.
Cleaning Burned-on Spills
Make sure that the heat indicator lights are o and that the
hob is cool. Remove the excess burned-on substance with a
single-edged razor scraper. Hold the scraper at an angle of
about 30° to the surface and then scrape o the burned-on
matter (Fig.5-1).
12
Page 17
Glide-out Grill
Before you remove any of the grill parts for cleaning,
make sure that they are cool, or use oven gloves.
Wash the grill pan and trivet washed in hot soapy water.
Alternatively, wash the grill pan in a dishwasher.
After grilling meats or any foods that soil, leave to soak for
a few minutes in the sink immediately after use. Stubborn
particles may be removed from the trivet by using a nylon
brush.
Removing and Refitting the Grill Pan and
Support Frame
Pull the grill pan forwards (Fig.5-2) and lift it clear of the
support frame.
The support frame is held to the side rails by two clips on
each side (Fig.5-3). For each side, support the side rail with
one hand and with the other hand lift the frame up and out
of the side clips (Fig.5-4).
For safety, push the grill tray back into the grill chamber.
If you need to remove the side rails to allow cleaning of the
grill chamber, you can unhook them from the grill chamber
sides (Fig.5-5) and wipe the sides clean with a soft cloth and
mild detergent.
Fig.5-2
Fig.5-3
DO NOT put the side runners in a dishwasher.
Once you have nished, hook the side rails back onto the
sides of the chamber. To ret the frame, pull the side rails
forwards and for each side in turn, support the side rail while
pressing the frame down into the side clips.
Replace the grill pan.
Fig.5-4
Fig.5-5
13
ArtNo.331-0005 Removing the grill rail
Page 18
Fig.5-6
Fig.5-7
12 3
Control Panel and Oven Doors
The control panel and control knobs should only be cleaned
with a soft cloth wrung out in clean hot soapy water – but
take care that no surplus water seeps into the appliance. Wipe
with a clean dampened cloth then polish with a dry cloth.
The oven doors should only be cleaned with a soft cloth
wrung out in clean hot soapy water.
Ovens
‘Cook & Clean’ Panels
The ovens have side ‘Cook & Clean’ panels which have been
coated with a special enamel that partly cleans itself. This
does not stop all marks on the lining, but helps to reduce the
amount of manual cleaning needed.
These panels work better above 200 °C. If you do most of your
cooking below this temperature, occasionally remove the
panels and wipe with a lint free cloth and hot soapy water.
The panels should then be dried and replaced and the oven
heated at 200 °C for about one hour. This will ensure that the
panels are working eectively.
DO NOT use steel wool (or any other materials that
will scratch the surface).
Fig.5-8
ArtNo.320-0022 Tall oven side support
DO NOT use oven cleaning pads.
The Oven Shelf Supports
The shelf supports on the oven sides can be removed for
cleaning.
Removing the Oven Shelf Supports
Remove the oven shelves. Pull the top of the shelf support up
and away from the oven side and then lift the support away
from the locating bracket at the bottom of the oven side
(Fig.5-6).
Retting the Oven Shelf Supports
To ret the side support. Locate the tag at the bottom of the
support into the slot in the locating bracket in the oven side
(Fig.5-7). Now locate the tops of the side arms in the holes at
the top and gently push down.
The Tall Oven
To clean the oven sides, slide out the shelves, unhook the
supports from the oven sides and lift out (Fig.5-8).
14
Page 19
Cleaning Table
Cleaners listed (Table 5-1) are available from supermarkets or
electrical retailers as stated.
For enamelled surfaces use a cleaner that is approved for use
on vitreous enamel.
Regular cleaning is recommended. For easier cleaning, wipe
up any spillages immediately.
Hotplate
Part Finish Recommended Cleaning Method
Hob top Enamel or stainless steel
Ceramic/Induction hob Toughened glass Hot soapy water; cream cleaner/scourer if necessary.
Griddle plate (some models only) Non-stick surface
Warming zone (some models only) Toughened glass Hot soapy water, cream cleaner/scourer if necessary.
Outside of Cooker
Part Finish Recommended Cleaning Method
Door, door surround and storage
drawer exterior
Enamel or paint
Stainless steel E-cloth or microbre all-purpose cloth (supermarket).
Hot soapy water, soft cloth. Any stubborn stains remove gently with
a nylon scourer.
Allow to cool. Wash in hot soapy water. Do not use abrasive
cleaners/scourers. Dishwasher.
Hot soapy water, soft cloth.
Any stubborn stains, remove gently with a liquid detergent.
Sides and plinth Painted surface Hot soapy water, soft cloth.
Splashback/rear grille Enamel or stainless steel Hot soapy water, soft cloth. Cream cleaner, with care, if necessary.
Control panel Paint, enamel or stainless steel Warm soapy water. Do not use abrasive cleaners on lettering.
Plastic/chrome, aluminium,
Control knobs/handles & trims
Oven door glass/glass lid Toughened glass Hot soapy water, cream cleaner/scourer if necessary.
copper or lacquered brass
Brass Brass polish.
Warm soapy water, soft cloth.
Oven and Grill
Part Finish Recommended Cleaning Method
Sides, oor & roof of oven NOT
‘COOK & CLEAN’ OVEN PANELS (see
below)
‘Cook & Clean’ oven panels (some
models only)
Oven shelves, Handyrack, grill
trivet, Handygrill rack
Grill pan/meat tin (some models
only)
Enamel
Special enamel that partly
cleans itself
Chrome
Enamel Hot soapy water. Soap lled pad. Dishwasher.
Any proprietary oven cleaner that is suitable for enamel.
CAUTION: CORROSIVE/CAUSTIC OVEN CLEANERS: FOLLOW
MANUFACTURER’S INSTRUCTIONS.
Do not allow contact with the oven elements.
This surface cleans itself at 200 °C and above, or the panels can be
removed and washed with hot soapy water and a nylon brush.
An oven interior cleaner that is suitable for chrome. Soap lled pad.
Dishwasher.
Table 5-1
15
Page 20
6. Troubleshooting
Interference with and repairs to the hob MUST NOT
be carried out by unqualied persons. Do not try
to repair the hob as this may result in injury and
damage to the hob. Please arrange for repair by a
suitably competent person.
Note: The induction hob is able to self-diagnose a
number of problems and can show this information to
the user via the hob control display. Error codes may be
displayed if your hob has developed a fault.
If your appliance reports an error or is not working,
you may be able to correct the fault by consulting the
following.
Error code E2 is displayed
The electronic unit is too hot. Please check the
installation of the cooker, making sure that there is
sucient ventilation. In extreme cases, if a cooking
utensil has been allowed to boil dry this error code
may also be displayed. If in doubt please contact your
installer or a qualied repair engineer.
No display operation
Over voltage or loss of supply voltage to the cooker. If in
doubt please contact your installer or a qualied repair
engineer.
Error code U400 is displayed
The cooker has been incorrectly connected. The control
will switch o after approximately 1 second and the
error code will be permanently displayed.
The cooling fan
The induction hob incorporates a cooling fan. This
cooling fan is active when either the grill or ovens
are on. Under certain conditions, the cooling fan may
remain active when the grill or ovens are switched o.
This is normal and the fan will switch o automatically.
A crack has appeared in the hob surface
Disconnect the cooker immediately from the power
supply and arrange for its repair. Do not use the cooker
until after the repair.
My hob is scratched
Always use the cleaning methods recommended in this
guide, and make sure that the pan bottoms are smooth
and clean.
Marks from mineral deposits from water or food can be
removed with a cleaning cream. However, tiny scratches
are not removable but will become less visible in time as
a result of cleaning.
The oven fan is noisy
The sound of the oven fan may change as the oven
heats up – this is perfectly normal.
Grill not cooking properly
Are you using the pan and trivet supplied with the
cooker? Is the pan being used on the runners, not the
oor of the compartment? Is the grill tray pushed back
fully to the ‘back stop’ position?
Consult your installer or a qualied repair engineer.
Error code Er followed by a number is displayed
The appliance has developed an internal technical fault
that cannot be rectied by the user.
Consult your installer or a qualied repair engineer.
The fuse blows or the RCD trips regularly
Please contact your installer or a qualied repair
engineer.
The hob will not switch on
Has the wiring system in the house blown a fuse or
tripped an RCD?
Has the hob been correctly connected to the mains
supply?
Has the child lock been activated? Please refer to the
child lock section for details of this function.
The induction hob is noisy
When using the induction hob there may be some
‘noise’ emitted from the pan. This is normal and may be
most noticeable when cooking on high power settings
or if 5 pans are used simultaneously. The type of pan
may also contribute to induction ‘noise’.
The knobs get hot when I use the oven or grill. Can I avoid
this?
Yes, this is caused by heat rising from the oven or the
grill, and heating them up. Do not leave the oven door
open. Make sure that the grill pan is pushed right back
to the ‘back stop’ when grilling.
Always grill with the grill compartment door open.
If there is an installation problem and I don’t get my
original installer to come back to x it, who pays?
You do. Service organisations will charge for their callouts if they are correcting work carried out by your
original installer. Therefore, it’s in your own interest to
keep track of this installer so that you can contact them
as required.
Food is cooking too slowly, too quickly, or burning
Cooking times may dier from your previous oven.
Check that you are using the recommended
temperatures and shelf positions – see the oven
cooking guide.
You can then adjust the settings according to your own
individual tastes.
16
Page 21
The oven is not cooking evenly
Do not use a baking tray with dimensions larger than
those specied in the section on ‘General Oven Tips’.
If you are cooking a large item, be prepared to turn it
round during cooking.
Fig.6-1
If two shelves are used, check that space has been left
for the heat to circulate. When a baking tray is put into
the oven, make sure that it is placed centrally on the
shelf.
Check that the door seal is not damaged and that the
door catch is adjusted so that the door is held rmly
against the seal.
A dish of water when placed on the shelf should be the
same depth all over. (For example, if it is deeper at the
back, then the back of the cooker should be raised up or
the front lowered.) If the cooker is not level, arrange for
your supplier to level it for you.
Oven temperature getting hotter as the cooker gets older
If turning the temperature down using the oven control
knob has not worked, or has only worked for a short
time, then you may need a new thermostat. This should
be tted by a service person.
The oven door is misaligned
The bottom hinge of the left-hand oven door can be
adjusted to alter the angle of the door (Fig.6-1). Loosen
the bottom hinge xing screws and use the notch and
a at bladed screwdriver to move the position of the
hinge to set the hinge position (Fig.6-2).
ArtNo.320-0006 Oven door hinge adjustment 1
Eect of hinge adjustment – exagerrated for clarity
Centreline of hinge pin
ArtNo.320-0007 Oven door hinge adjustment 2
Oven door omitted for clarity
Fig.6-2
Retighten the hinge screws.
17
Page 22
7. Installation
ArtNo.350-0008 - 90 SC plinth
INSTALLATION
Check the appliance is electrically safe when you have nished.
Dear Installer
Before you start your installation, please complete the details
below, so that, if your customer has a problem relating to
your installation, they will be able to contact you easily.
Installer’s Name
Installer’s Company
ArtNo.050-0011 - Installer information table
Installer’s Telephone Number
Appliance Serial Number
You will need the following equipment to complete the
cooker installation satisfactorily:
• Multimeter (for electrical checks).
• Allen keys (provided in pack).
You will also need the following tools:
Steel tape measure
1.
2. Cross-head screwdriver
3. Flat head screwdriver
4. Spirit level
5. 13mm spanner or socket wrench
Checking the Parts:
Grill pan and trivet 2 at shelves
1 drop shelf
Tall oven shelves and shelf
supports
Safety Requirements and Regulations
You must be aware of the following safety requirements &
regulations.
This cooker must be installed in accordance with
the relevant instructions in this booklet, with the
relevant national and local regulations, and with the
local electricity supply companies’ requirements.
The appliance must be installed in accordance with
the regulations in force and only in a well-ventilated
space.
Read the instructions before installing or using this
appliance.
This appliance is designed for domestic cooking
only. Use for any other purpose could invalidate any
warranty or liability claim.
Provision of Ventilation
This appliance is not connected to a combustion products
evacuation device. Therefore, particular attention must be
given to the relevant requirements regarding ventilation.
All rooms require a window that can be opened, or
equivalent, while some rooms require a permanent vent in
addition to the window.
ArtNo.000-0010 Tall oven shelves
1-piece plinth
Location of Cooker
The cooker may be installed in a kitchen/kitchen diner but
NOT in a room containing a bath or shower.
18
Page 23
INSTALLATION
130 mm min
75 mm
min
75 mm
min
800 mm
min
912 mm min
937 mm max
900 mm minimum*
(check cookerhood instructions for actual dimensions)
410 mm
minimum
800 mm
minimum
5 mm 5 mm
**
Check the appliance is electrically safe when you have nished.
Positioning the Cooker
Fig.7-1 and Fig.7-2 show the minimum recommended
distance from the cooker to nearby surfaces.
The cooker should not be placed on a base.
Above hotplate surround should be level with, or above, any
adjacent work surface.
A gap of 75 mm should be left between each side of the
cooker ABOVE the hotplate level and any adjacent vertical
surface.
For non-combustible surfaces (such as unpainted metal or
ceramic tiles), this can be reduced to 25 mm.
A minimum space of 800 mm is required between the top of
the hotplate and a horizontal combustible surface.
* Any cookerhood should be installed in accordance with the
hood manufacturer’s instructions.
**Any splashback must be tted in accordance with the
manufacturers instructions. Allowance should be made for the
ue trim, which is tted to the cooker hob.
Surfaces of furniture and walls at the sides and rear of the
appliance should be heat, splash and steam resistant. Certain
types of vinyl or laminate kitchen furniture are particularly
prone to heat damage and discolouration.
Fig.7-1
*
Fig.7-2
We cannot accept responsibility for damage caused by
normal use of the cooker to any material that de-laminates
or discolours at temperatures less than 65 °C above room
temperature.
We recommend a gap of 910 mm between units to allow
for moving the cooker. Do not box the cooker in – it must
be possible to move the cooker in and out for cleaning and
servicing.
If the cooker is near a corner of the kitchen, a clearance of
130 mm is required to allow the oven doors to open (Fig.7-3).
The actual opening of the doors is slightly less but this allows
for some protection of your hand as you open the door.
Moving the Cooker
On no account try and move the cooker while it is
plugged into the electricity supply.
The cooker is very heavy, so take great care.
We recommend that two people manoeuvre the cooker.
Make sure that the oor covering is rmly xed, or removed,
to prevent it being disturbed when moving the cooker
around.
To help you, there are two levelling rollers at the back, and
two screw-down levelling feet at the front.
Remove the polystyrene base pack. From the front, tilt the
cooker forward and remove the front half of the polystyrene
base (Fig.7-4). Repeat from the back and remove the rear half
of the polystyrene base.
Fig.7-3
Fig.7-4
19
Page 24
INSTALLATION
Check the appliance is electrically safe when you have nished.
Fig.7-5
Fig.7-6
Stability bracket
ArtNo.010-0004 Moving the cooker
Cooker
3 mm min
ArtNo.070-0014 - Stability bracket - Wall fitting
Floor
Lowering the Two Rear Rollers
To adjust the height of the rear of the cooker, rst t a 13 mm
spanner or socket wrench onto the hexagonal adjusting
nut (Fig.7-5). Rotate the nut – clockwise to raise – counterclockwise to lower.
Make 10 complete (360°) turns clockwise.
Make sure you lower BOTH REAR ROLLERS.
Completing the Move
Unfold the rear edge of the pack base tray. Open the grill
door and right-hand oven door so that you can get a good
grip on the bottom of the fascia panel as you move the oven
(Fig.7-6).
Carefully push the cooker backwards o the pack base.
Remove the pack base tray.
Position the cooker close to its nal position, leaving just
enough space to get behind it.
DO NOT use the door handles or control knobs to
manoeuvre the cooker.
Fitting the Stability Bracket
Suitable stability devices are shown in Fig.7-7 and Fig.7-8.
If you are using a stability bracket (Fig.7-7 and Fig.7-8), then
adjust the bracket to give the smallest practicable clearance
between the bracket and the engagement slot in the rear of
the cooker.
Fit the bracket so that it engages as far as possible over the
chassis of the cooker.
Fig.7-7
Fig.7-8
Typical oor mounting
Typical oor mounting
Outer stability
bracket
3 mm min
Wall
Typical wall mounting
Typical wall mounting
Cooker
Floor
Repositioning the Cooker Following
Connection
If you need to move the cooker once it has been connected
then you need to unplug it and, having gripped under the
fascia panel and lifted the front of the cooker slightly
(Fig.7-6), you need to check behind the cooker to make sure
that the electricity cable is not caught.
As you progress, make sure that the electricity cable always
has sucient slack to allow the cooker to move.
When you replace the cooker, again check behind to make
sure that the electricity cable is not caught or trapped.
Levelling
You are recommended to use a spirit level on a shelf in one of
the ovens to check for level. Place the cooker in its intended
position taking care not to twist it within the gap between
the kitchen units as damage may occur to the cooker or the
units. The front feet and rear rollers can be adjusted to level
the cooker. To adjust the height of the rear of the cooker, use
a 13 mm spanner or socket wrench to turn the adjusting nuts
at the front bottom corners of the cooker.
To set the front turn the feet bases to raise or lower.
20
Page 25
INSTALLATION
Check the appliance is electrically safe when you have nished.
Electrical Connection
The cooker must be installed by a qualied electrician, in
accordance with all relevant British Standards/Codes of
Practice (in particular BS 7671), or with the relevant national
and local regulations.
Current Operated Earth Leakage Breakers
The combined use of your cooker and other domestic
appliances may cause nuisance tripping, so we
recommend that the cooker is protected on an individual
RCD (Residual Current Device) or RCBO (Residual Current
Breaker with Overload).
IF IN DOUBT, PLEASE CONSULT A SUITABLY QUALIFIED
ELECTRICIAN.
Note: The cooker must be connected to the correct electrical
supply as stated on the voltage label on the cooker, through
a suitable cooker control unit incorporating a double pole
switch, having a contact separation of at least 3 mm in all
poles.
The cooker MUST NOT be connected to an ordinary
domestic power point.
Access to the mains terminal is gained by removing the
electrical terminal cover box on the back panel. Connect the
mains cable to the correct terminals for your electrical supply
type (Fig.7-9 and Fig.7-10). Check that the links are correctly
tted and that the terminal screws are tight.
L
N
10 mm² max
ArtNo.130-0010 Electrical connections single-phase
230 V ac 50 Hz
L1
N
L3
L2
6 mm² max
3N ac
230/400 V 50 Hz
Fig.7-9
6 mm² max
Fig.7-10
6 mm² max
10 mm² max
Secure the mains cable using the cable clamp.
Final Checks
Hotplate Check
Check each cooking zone in turn. Be sure to use pans of the
correct size and material.
Grill Check
Turn on the grill control and check that the grill heats up.
Oven Check
Turn on the ovens – check that the oven fans start to turn and
that the ovens start to heat up.
Fitting the Plinth
Remove the 3 screws along the bottom edge of the cooker.
Hold the plinth in place and ret the 3 screws.
Customer Care
Installer: Please complete your details in this guide, inform
the user how to operate the cooker and hand over the
instructions.
Thank you.
21
Page 26
8. Circuit Diagrams
Induction Hob Circuit Diagram
Circuit Diagram: Hob
1
Left Front
br
Left Rear
2
br
5
Centre
x1
Interface
x6
Hob Display
Induction unit
board
x2
x5
x3x4
br br
br
br
3
Right Rear
4
Right Front
br
5431 2 E
br
gbbbrbr
6 way connector
6 way connector
Code Colour
g Green
b Blue
br Brown
E
22
Page 27
Circuit Diagram: Oven
br
F
v
2
P2
A1
P1
r
1
bk
P095199
br
A2
(H6)
br
v
v
bk
A4
A3
C
br
F
br
br
r
b
1
2
B2
v
br
br
br
b
v
br
8 P8
w
B3
7 P7
6
5 P5
4
3 P3
2
1 P1
B4
gr
w
y
or
b
v
B5
B6
B7
r
B8
Hob1
P6
P2
P4
Hob2
w
br
E
b
b
E
b
Hob3
Hob4
Hob5
w
or
b
F
2
P2
D1
1
P1
P095199
v
1
2
D2
w
b
b
D3
E
D4
b
b
E
Key
The connections shown in the circuit diagram are for single-phase. The ratings are for 230 V 50 Hz.
Code Description
A1 Grill front switch
A2 Grill control
A3 Grill left-hand element
A4 Grill right-hand element
B2 Multi-function oven thermostat
B3 Multi-function oven function switch
B4 Multi-function oven top element
B5 Multi-function oven browning element
B6 Multi-function oven fan element
B7 Multi-function oven base element
Code Description
B8 Multi-function oven fan
C Cooling fan
D1 Right-hand oven front switch
D2 Right-hand oven thermostat
D3 Right-hand oven fan element
D4 Right-hand oven fan
E Thermal cut-out
F Neons
Code Colour
b Blue
br Brown
bl Black
or Orange
r Red
v Violet
w White
y Yellow
g/y Green/yellow
gr Grey
23
Page 28
9. Technical Data
INSTALLER: Please leave these instructions with the user.
DATA BADGE LOCATION: Cooker back, serial number repeater badge below door opening.
COUNTRIES OF DESTINATION: GB, IE, FR, DE, NL, SE, BE, AT, CH.
Connections
Electric 230 / 400 V 50 Hz
Dimensions
Total height Min 912 mm Max 937 mm
Total width 900 mm
Total depth 600 mm (to fascia); 670 mm (over handles)
Minimum height above cooker 800 mm
Refer to ‘Positioning the Cooker’.
Ratings
Max: 1.85 kW
Boost: 3.0 kW
Max: 2.3 kW
Boost: 3.7 kW
Max: 1.85 kW
Boost: 3.0 kW
Max: 1.4 kW
Boost: 2.2 kW
Ovens
Maximum power output @ 230 v 50 Hz 2.5 kW 2.5 kW
Energy eciency class on a scale of A (more ecient) to G (less ecient) A A
Energy consumption based on standard load 0.95 kWh 0.99 kWh
Usable volume (litres) 78 66
Size Large Large
Time to cook standard load 41 minutes 48 minutes
Surface area of the grid 1400 cm
Grill 2.3 kW
Maximum total electric load at 230 V 50 Hz
Max: 1.85 kW
Boost: 3.0 kW
(approximate total including oven lights, oven fan, etc.): 18.4 kW.
Left-hand Oven Right-hand Oven
Multi-function Forced Air Convection
2
1056 cm
2
24
Page 29
10. Warranty/After Sales Service
If consultation or technical assistance is needed, please
provide the local authorised service agent with the purchase
invoice and the product code/serial number.
This information is on the appliance data badge. This is
located inside the drawer cavity base. For removal of the
drawer see the ‘Overview / Storage’ section.
The 3 years free maintenance for the operation of the
appliance started from the date of purchase of this product.
Any cosmetic damage to the appliance must be reported
within 90 days of delivery.
For in-warranty service please call: 0845 6035312.
For general enquiries please call: 0870 7895107.
If You Have a Problem
In the unlikely event that you have a problem with your
appliance, please refer to the rest of this booklet, especially
the ’Troubleshooting’ section, rst to check that you are using
the appliance correctly.
If you are still having diculty, contact your retailer.
Notes
If your appliance is outside the 3 year warranty period, our
service provider may charge for this visit.
If you request an engineer to visit and the fault is not the
responsibility of the manufacturer, our service provider
reserves the right to make a charge.
Appointments not kept by you may be subject to a charge.
Out of Warranty
We recommend that our appliances are serviced regularly
throughout their life to maintain the best performance and
eciency.
Any servicing work should only be carried out by technically
competent and suitably qualied personnel.
Spare Parts
To maintain optimum and safe performance, only use
genuine parts. Do not use reconditioned or unauthorised
controls. Contact your retailer.
25
Page 30
26
Page 31
Name of Appliance & Colour*
Appliance Serial Number*
Natural Gas
Fuel Type*
Dual Fuel Electric
Retailer's Name & Address
Date of Purchase
LP Gas
For warranty compliance, the requirements are that the
appliance:
¥ Has been correctly installed in accordance with current
legislation, relevant British and European Standards
and Codes of Practice, by a suitably competent person
registered with Gas Safe or equivalent body and, where
applicable, a qualified electrician.
¥ Has been used solely for domestic cooking purposes.
¥ Is in use in the UK*, has not been taken abroad as a
personal export. (In the Republic of Ireland conditions
may vary, so consult your retailer.)
¥ Is not second-hand or a refurbished appliance. The
manufacturer's warranty is not transferable.
¥ Has not been subject to misuse, accidental damage or
modification, and has not deteriorated due to normal
domestic wear and tear, and the manufacturer's
recommendations concerning cleaning materials have
been followed.
¥ Has not been repaired by persons or organisations
other than those authorised to act on behalf of AGA
Rangemaster.
Installer's Name & Address
Installer's Telephone Number
Date of Installation
* This information is on the appliance data badge Ð look in the
appliance instructions to find out where the data badge is located.
CONSUMER SERVICE
If you have any product enquiries, or in the event of a problem
with your appliance once it has been installed, please
telephone 0870 789 5107.
CONSUMER SERVICE LINES OPEN:
Monday to Thursday 8amÐ6pm
Friday 8amÐ5pm
Saturday 9amÐ1pm
Exceptions:
¥ Items not included under the free 3 year guarantee
include pan supports, griddles, wok rings, baking
trays, grill pans, trivets, filters, light bulbs and other
consumable accessories.
¥ Any damage caused other than through normal use.
¥ Breakdowns associated with cooking spillage.
¥ Cosmetic deterioration deemed to be normal wear and
tear.
This warranty is in addition to your Statutory Rights.
* Only certain models can be adapted for use with Mains Gas
supplied in the Channel Islands and Isle of Man.
OUT OF WARRANTY
We recommend that Falcon appliances are serviced regularly
throughout their life to maintain optimum performance
and efficiency. Service work should only be carried out by
technically competent and suitably qualified personnel.
For your own safety, always make sure that work is carried
out by a Gas Safe registered engineer for gas appliances or an
approved electrician for electrical models.
For a competitive quote and to arrange for a Falcon approved
engineer to attend, call Consumer Services on: 0870 789 5107.
WARRANTY
Your manufacturer warranty covers goods of our own brand
for defective workmanship and materials for a period of 3 year
from the date of purchase. This warranty covers mechanical
breakdown and proven cosmetic and manufacturing defects.
To register for this guarantee simply fill in and return the
FREEPOST registration form provided. Alternatively call free on
0800 694 4170, quoting reference FAGX91AN or register
online at www.falconappliances.co.uk
Any damage, blemishes or chips identified upon receipt of the
product must be reported within 90 days – proof of purchase
may be required to establish validity. Scratches on the surface
of ceramic hobs must be reported within 14 days. Scratches
caused by usage are not covered. Accidental damage is not
covered by the manufacturer's warranty.
SPARE PARTS
To maintain optimum and safe performance, we recommend
that only genuine Falcon spare parts are used. These are
available from most major spares stockists, including ourselves.
Contact Consumer Services on 0870 789 5107, who will be
happy to help.
STANDARDS
Falcon cookers are designed and manufactured to a recognised
international quality standard, which meets the requirements
of BS EN ISO 9001, BS EN ISO 14001 and OHSAS 18001 for
continually improving environmental procedures.
Falcon cookers comply with the essential requirements of the
appropriate European Directives, and carry the CE mark.
Page 32
For over 45 years
Divertimenti, Falcon’s
sister company, has
been the ultimate destination
for food lovers and serious
chefs alike. With its vast array
of cookware, tableware and
kitchenware, Divertimenti
caters to all your culinary needs.
With over 4500 items on the
Divertimenti
website www.divertimenti.co.uk
Falcon Appliances
Clarence Street
Royal Leamington Spa
Warwickshire
CV31 2AD
Tel 0870 755 6490
Fax 0192 631 1032
Email consumers@falconappliances.co.uk
www.falconappliances.co.uk
Trade Enquiries 0115 946 6143
Email sales@falconappliances.co.uk
Registered in England and Wales. Registration No. 354715 Registered Office: Juno Drive, Leamington Spa, Warwickshire, CV31
3RG
Falcon continuously seeks improvements in specification, design and production of products and thus, alterations take place
periodically. Whilst every effort is made to produce up-to-date literature, this booklet should not be regarded as an infallible
guide to current specification, nor does it constitute an offer for the sale of any particular appliance.
Loading...