Fairport FP300, FPC320 Operator's, Spare Parts & Service Manual

OPERATOR'S SPARE PARTS & SERVICE MANUAL
Blagden Street
Sheffield
S2 5QS ENGLAND Tel: +44 (0) 114 276 7921 Fax: +44 (0) 114 272 0965 Email: sales@fairport.uk.com Web: www.fairport.uk.com
!
FAIRPORT
CONSTRUCTION EQUIPMENT LTD
CONTENTS PAGE
1. SAFETY ………………………………………………………………………… 2 SAFETY PICTOGRAMS USED ON FAIRPORT EQUIPMENT ………….. 2
2. TECHNICAL DATA ……………………………………………………………. 3
3. USING THE MACHINE FOR THE FIRST TIME……………………………. 4
4. ROUTINE MAINTENANCE …………………………………………………… 4
5. STARTING THE ENGINE ……………………………………………………. 5
6. OPERATOR INSTRUCTIONS ……………………………………………….. 5
7. VEE BELT ADJUSTMENT ……………………………………………………. 5
8. WARRANTY CONDITIONS AND CLAIMS PROCEDURE ……………….. 5
CONDITIONS …………………………………………………………………... 6 CLAIMS PROCEDURE ………………………………………………………... 6
9. REPAIRS AND ESTIMATES ………………………………………………….. 7
10. ENVIRONMENT…………………………………………………………………. 7
11. PARTS LIST ……………....……………………………………………………. 8
MACHINE …………………………………………………………………8 POLYPAD MAT KIT ……………………………………………………..14 WATER SPRINKLER KIT……………………………………………….15
12. EC Declaration Of Conformity…………………………………………………..17
1
1. SAFETY
Do not operate this machine unless all guards are in position and secure. Do not smoke when refuelling. Do not refuel with engine running. Wipe up spilt fuel. Do not overfill. Dispose of fuel contaminated wipes safely Do not run engine in enclosed areas without adequate ventilation. Do not run engine in an area that has a hazardous or explosive atmosphere. Disconnect H.T. lead from spark plug on petrol engines before carrying out any maintenance. Turn off fuel when not using machine. Wear protective footwear, ear defenders and gloves. Comply with site safety regulations. Check condition and tightness of anti-vibration mounts between engine plate and base plate before lifting.
SAFETY PICTOGRAMS USED ON FAIRPORT EQUIPMENT
2
2. TECHNICAL DATA
ENGINE
MODEL ENGINE
MANUFACTURER
ENGINE MODEL
POWER (HP/kW)
FPC300
Robin EH09 3.0/2.2
FPC320
Honda GX100 3.0/2.2
DIMENSIONS
MODEL HEIGHT- H
(mm)
LENGTH – L (mm)
WIDTH – W (mm)
CONTACT AREA (sq. m)
WEIGHT (kg)
FPL300
614 550.2 300 0.095 54
FPL320
614 550.2 320 0.10 55
PERFORMANCE
MODEL CENTRIFUGAL
FORCE (kN)
COMPACTION RATIO (kg/m²)
VIBRATION LEVELS (m/sec²)
FPL300
10 568 2.87*
FPL320
10 550 3.04*
*Tested in accordance with BS 500-4 on uncompacted granular sub base materials and is the minmum expected level.
NOISE EMMISIONS
MODEL GUARANTEED SOUND
POWER LEVEL dB
FPL300
103
FPL320
108
3
3. USING THE MACHINE FOR THE FIRST TIME
When the machine is delivered from Fairport it will have no oil in the engine. Please refer to the Engine Manufacturers Manual issued with the machine for instructions on filling the engine with the correct type and quantity of oil. When the machine is delivered from Fairport there is oil in the vibrator unit. Refer to Section 4 for advise on checking the oil level and topping up as required.
4. ROUTINE MAINTENANCE
(See Also The Engine Manufacturers Manual issued with the machine)
Daily
: Check engine oil level twice daily.
Check tightness of all fastenings after first days use, thereafter check monthly. Check belt tension after first days use, thereafter check monthly. Clean air filter daily if working in dusty conditions. Clean base plate throroughly if compacting black-top or lean concrete.
Weekly:
Clean air filter (see “daily”).
Check Vibrator Oil level.
Monthly:
Check tightness of fastenings.
Check condition and tightness of anti-vibration mounts. Poor condition of vibration mountings can lead to a deterioration of the product vibration levels. Check belt tension.
Vibrator Unit Remove the Oil Level Plug to check the oil level. The level should be at the bottom of the thread in the vibrator end face. To top up, remove the filler plug and fill with Total PRESLIA 32 or equivalent.
4
FILLER PLUG
OIL LEVEL PLUG
OIL LEVEL
5. STARTING THE ENGINE
Check oil level. Turn fuel tap on. Put speed control lever to tick-over. If engine is cold, close the choke (petrol engines only). Turn engine switch to ON(1) position. Pull the starter rope toggle lightly until resistance is felt, then pull briskly using quick short pull. Do not pull rope to its full extent or allow toggle to snap back against engine. Return gently to avoid damage.
When the engine is warm, open choke. Position engine speed control lever to give required engine speed (usually full speed). Commence vibration – the compactor is self – travelling. To stop the engine, postion the engine speed control to slow and turn the engine switch to off(0). Turn the fuel valve off.
6. OPERATOR INSTRUCTIONS
Read section (1) - Safety. NOTE: Drive between engine and vibrator is through a centrifugal clutch. Vibration will commence as engine speed is increased. Position the engine speed control lever to give required speed (usually full speed). Commence compaction. The compactor is self-travelling. Its speed of travel and the number of passes required to achieve optimum compaction depends on the type and condition of material being compacted and the layer depth. Uniformly graded granular material compacts far more efficiently than wet cohesive material. When Compacting block paving always use a rubber attachment mat, contact your agent for details. When compacting blacktop always use a water spray, contact your agent for details.
Do not run the machine on solid surfaces, as this is likely to cause damage.
7. VEE BELT ADJUSTMENT
It is important to note that belt tension in this application is much less than is generally accepted as normal. Too high a belt tension may lead to engine damage, excessive vibration in the handle, short belt life and short vibrator shaft bearing life due to excessive transmission of vibration through the belt. Correct adjustment is achieved by moving the engine back to just take the slack out of the belt. With light finger pressure on top of the belt and at the centre of the span, a deflection of between 5mm and 10mm is expected.
5
8. WARRANTY CONDITIONS AND CLAIMS PROCEDURE
All products supplied by Fairport Construction Equipment Ltd (hereafter referred to as FCE) are warranted to be free of defects due to faulty materials or workmanship for a period of 12 months from the date of original despatch from FCE or as specified below:
Hydraulic hoses and hydraulic couplings – 3 months. Hydraulic accumulators – 6 months. Flexible drives – 6 months. All spare parts used in repairs carried out by FCE or an authorised dealer or repairer – 3 months.
If the goods have been purchased through a stockist the above warranty periods also apply from receipt of the goods by the user of the equipment up to a total of a further 6 months from date of despatch from FCE whichever is earlier.
Filter elements, gauges and oils are specifically excluded from this warranty. FCE shall at their option repair or replace during normal working hours goods accepted as faulty free of charge to the user. For proprietary items such as engines, the original manufacturer’s warranty and conditions shall apply.
CONDITIONS The goods shall be returned at the purchaser’s expense to FCE or to a destination
FCE may reasonably direct. Carriage costs will be refunded if warranty is accepted. Warranty claims will not be considered where there is evidence that failure has been caused by carelessness, improper use, negligence, inadequate servicing, incorrect engine speeds, fair wear and tear or non-compliance with instructions issued by the manufacturer. To the extent permitted by law, the liability of FCE under this section is confined only to providing a remedy for defective goods and does not extend to any consequential loss, loss of profit, injury or damage suffered. Warranty will not be accepted on dismantled goods unless dismantling was carried out with the written permission of FCE. No claim shall be considered if other than genuine parts supplied by FCE have been used.
Products are only covered by this warranty in the country to where they were supplied by FCE.
Warranty on products applies only to the original user of the equipment. This warranty shall not apply if the serial number or other identifying numbers or marks applied by FCE have been removed, defaced or are otherwise illegible.
CLAIMS PROCEDURE Check that the goods are still under warranty before returning them to FCE (see
above for warranty periods). Return the goods to FCE with an order number for the work to proceed. If warranty is accepted no charge will be made. If warranty is not accepted a quotation will be
6
given for the repair and the conditions under the section headed REPAIRS AND ESTIMATES will apply. In the customer’s interest, goods must be accompanied by documentation detailing the nature of the fault or its symptoms. Phrases such as ‘Faulty’ are unacceptable and will result in delays and possible charges to defray costs incurred in identifying the fault.
In the case of hydraulic breakers and power packs, both the breaker and the pack should be returned.
9. REPAIRS AND ESTIMATES
When returning a machine, or an assembly for repair, always include an Advice Note quoting model and serial number of the machine. An official order must also be forwarded to FCE giving detailed instructions. No repair work can be carried out unless covered by an official order. An estimate will be submitted before proceeding with any repair. To partly cover the cost in dismantling, cleaning and inspection, a small charge will be made, this however will be waived upon receipt of your official instructions to proceed with the repair. In the event of the estimate not being accepted, a further charge will be made to defray the rebuilding of the machine.
Estimates must be treated as approximate only as it may be found necessary to use additional parts on further examination.
10. ENVIRONMENT
This machine contains materials that can be recycled. We recommend that when the machine is disposed off it is done safely and in a way that protects the environment.
Part Description Materials Engine Aluminium and steel Baseplate Steel Engine Frame Steel Engine Bedplate Steel Belt Cover High Density Polyethylene Handle Steel and Polyurethane Ant vibration Mounts Steel and rubber Block Paving Kit (if fitted) Steel and Polyurethane Water Bottle Kit (if fitted) Steel and Medium Density Polyethylene Transporter kit (if fitted) Steel and Rubber
7
1. PARTS LIST – MACHINE DRIVE SYSTEM
Parts List
Part Code Description Qty Required
1 W14644 Belt Guard 1 2 W87300 Vee Belt 1 3 W87061 Clutch (FPC320) 1 3 W87060 Clutch (FPC300) 1 4 P80167 1/4 UNF x 1” Setscrew (FPC320) 1 4 W408/5/16 5/16” UNF x 1” Setscrew (FPC300) 1 5 W432/6 M6 Spring Washer (FPC320) 1 5 W432/8 M8 Spring Lock Washer (FPC300) 1 6 W14719 Retaining Washer (FPC320) 1 6 P80120 Retaining Washer (FPC300) 1 7 W14666 Clutch Spacer (FPC300) 1 8 W14689 Belt Guard Back Plate 1 9 W14681 Engine Spacer 1 10 W466/5/12 5/16 UNF x ¾” Csk Setscrew (FPC320) 4 10 W469/8/20 M8 x 20 Csk Setscrew (FPC300) 4 11 W437/8/20 M8 x 20 Setscrew 2 12 W432/8 M8 Spring Lock Washer 2 13 W418/8 M8 Washer 2 14 W14690 Engine Shaft Key 1
8
PARTS LIST – MACHINE
Parts List Part Code Part Description Qty Required
1 W14663 Frame 1 2 W81925 Honda GX100 (FPC320) 1 2 W81800 Robin EH09 (FPC300) 1 3 W14662 Engine Bed Plate 1 4 W14680 Engine Fixing Plate 1 5 W418/8 M8 Washer 4 6 W437/8/30 M8 x 30 Hex Setscrew 4 7 W440/8 M8 Nut 4 8 W432/8 M8 Spring Lock Washer 4 9 W88914 AV Buffer 1 10 W418/10 M10 Washer 1 11 W480/10 M10 Nyloc Nut 1 12 W437/8/25 M8 x 25 Hex Setscrew 4 13 W418/8 M8 Washer 4 14 W480/8 M8 Nyloc Nut 4
Not Ilisttrated
17 W14767 Engine Packer (FPC300) 2
9
PARTS DIAGRAM – MACHINE
10
PARTS LIST – BASEPLATE ASSEMBLY
Parts List
Part Code Description Qty Required
1 W14653 End Cap 1 2 W14679 Gasket 2 3 W81090 Bearing 2 4 W14661-2 Eccentric Weight 1 5 W14660 Base (FPC320) 1 5 W14678 Base (FPC300) 1 5 W14764 Base (FPC350) 1 5 W14765 Base (FPC400) 1 6 W87301 Key 8 x 7 x 15 1 7 W81270 Oil Seal (Up To Serial No. 58427) 1 7 W81271 Oil Seal (From Serial No. 58428) 1 8 W14655 End Cap (Up To Serial No. 58427) 1 8 W14707 End Cap (From Serial No. 58428) 1 9 W14656 Pulley 1 10 W435/10/40 Hex Bolt M10 x 40 1 11 W68574 Filler Cap 1 12 W418/10 M10 Washer 1 13 W535/10 M10 Nordlock Washer 1 14 W455/10/30 M10 x 30 Socket Head Cap Screw 2 15 W14661-1 Eccentric Shaft (Up To Serial No. 58427)1 15 W14705 Eccentric Shaft (From Serial No. 58428) 1 16 P85034 Dowty Washer 1 17 W432/10 M10 Spring Lock Washer 1 18 W455/6/18 M6 x 18 Socket Head Cap Screw 8 19 W432/6 M6 Spring Lock Washer 7 20 P70282 Dowty Washer 1 21 W437/10/18 M10 x 18 Hex Setscrew 4 22 W432/10 M10 Spring Lock Washer 8 23 W88911 AV Mount AVM 2312s/38 4 24 W418/10 M10 Washer 4 25 W440/10 M10 Nut 4
11
PARTS DIAGRAM – BASEPLATE ASSEMBLY
5
2
2
3
6
1
3
4
5
7
8
9
10
11
17
13
14
15
16
18
19 20
21
22
22
23
24
25
24
12
PARTS LIST – HANDLE ASSEMBLY
Parts List Part Code Part Description Qty Required
1 W14667 Handle 1 2 W88913 AV Mount 4 3 W437/8/16 M8 x 16 Hex Setscrew 4 4 W480/8 M8 Nyloc Nut 4 5 W432/8 M8 Spring Lock Washer 4 6 W14668 Top Plate 1 7 W14683 Handle Pivot Bolt 2 8 W88912 Handle Bush 2 9 W418/8 M8 Washer 4
12
PARTS DIAGRAM – HANDLE ASSEMBLY
13
PARTS LIST – PAVING MAT MIT
Model Parts List Part Code Part Description Qty FPC300 1 W14724 Polypad 1 2 W14728 Clamp bracket 1 FPC320 1 W14725 Polypad 1 2 W14729 Clamp Bracket 1 Common 3 M10 X 40 Coach Bolts 4 4 W480/10 M10 Nyloc Nut 4 5 W418/10 M10 Washer 4
The paving mat kits have been designed to allow the machine to be used for compacting hard paving. To fit the mat, insert the lugs on the mat into the slots in the base plate. Fold under the machine. Ensure that the correct size paving mat is selected to match the baseplate width.
14
PARTS LIST – WATER SPRINKLER KIT
Model
Parts List Part Code Part Description Qty Required
FPC300 ------------- W14693 Spray Bar Comp 1 W14692 Spray Bar 1 2 W80566 Insert 2 FPC320 ------------- W14692 Spray Bar Comp 1 W14685 Spray Bar 1 2 W80566 Insert 2 Common 3 W14670 Water Bottle 1 4 W88460 ¼ BSP M/F Elbow 1 5 W87864 ¼ BSP M/F Ball 1 Valve 6 W88046 Hose Tail ¼ X ¼ 1 7 W14713 Hose 1 8 W84189 O Clip 2
15
PARTS DIAGRAM – WATER SPRINKLER KIT
16
EC DECLERATION OF CONFORMITY
WE, FAIRPORT CONSTRUCTION EQUIPMENT LTD, BLAGDEN ST, SHEFFIELD, SOUTH YORKSHIRE, S2 5QS
DECLARES THAT THE PRODUCT:
FPC320; FITTED WITH A HONDA GX100 ENGINE ENGINE POWER; 3.0HP/2.2kW at 3600RPM
SERIAL No. ………………………………
CONFORMS TO THE FOLLOWING DIRECTIVE:
89/336/EEC, 89/392/EEC, 91/368/EEC, 2000/14/EC
NOTIFIED BODY; AV Technology Ltd, AVTECH House, Birdhall Lane, Cheadle Heath, Stockport, Cheshire. SK3 0XU. GB.
USES THE FOLLOWING STANDARDS:
BS EN 292-1, BS EN 292-2, BS EN 294, BS EN 500-4
CONFORMS TO THE FOLLOWING STATUTORY INSTRUMENTS
THE SUPPLY OF MACHINERY (SAFETY) REGULATIONS 1992 & AMMENDMENTS
COMPLIES WITH THE RELEVANT ESSENTIAL HEALTH & SAFETY REQUIREMENTS OF THE MACHINERY DIRECTIVE
DECLARATION
I certify that on completion of manufacture of the machine detailed above that a full conformity has been completed and relevant Health and Safety Requirements complied with.
NAME: IAN MORRIS
STATUS WITHIN COMPANY: TECHNICAL MANAGER
SIGNATURE:
17
Loading...