Fairchild Semiconductor NM24C09EN, NM24C09FDICE, NM24C09LEM8, NM24C09LEM8X, NM24C09N Datasheet

1

www.fairchildsemi.com

NM24C08/09 Rev. G

NM24C08/09 – 8K-Bit Standard 2-Wire Bus Interface Serial EEPROM

February 2000

© 1998 Fairchild Semiconductor Corporation

NM24C08/09 – 8K-Bit Standard 2-Wire Bus
Interface Serial EEPROM

General Description

The NM24C08/09 devices are 8192 bits of CMOS non-volatile
electrically erasable memory. These devices conform to all speci­fications in the Standard IIC 2-wire protocol and are designed to
minimize device pin count, and simplify PC board layout require­ments.

The upper half (upper 4Kbit) of the memory of the NM24C09 can be
write protected by connecting the WP pin to VCC. This section of
memory then becomes unalterable unless WP is switched to VSS.

This communications protocol uses CLOCK (SCL) and DATA
I/O (SDA) lines to synchronously clock data between the master
(for example a microprocessor) and the slave EEPROM device(s).
The Standard IIC protocol allows for a maximum of 16K of
EEPROM memory which is supported by the Fairchild family in
2K, 4K, 8K, and 16K devices, allowing the user to configure the
memory as the application requires with any combination of
EEPROMs. In order to implement higher EEPROM memory
densities on the IIC bus, the Extended IIC protocol must be used.
(Refer to the NM24C32 or NM24C65 datasheets for more infor­mation.)

Fairchild EEPROMs are designed and tested for applications requir­ing high endurance, high reliability and low power consumption.

Block Diagram

Features

■ Extended operating voltage 2.7V – 5.5V

■ 400 KHz clock frequency (F) at 2.7V - 5.5V

■ 200µA active current typical

10µA standby current typical
1µA standby current typical (L)

0.1µA standby current typical (LZ)

■ IIC compatible interface
– Provides bi-directional data transfer protocol

■ Schmitt trigger inputs

■ Sixteen byte page write mode

– Minimizes total write time per byte

■ Self timed write cycle
Typical write cycle time of 6ms

■ Hardware Write Protect for upper half (NM24C09 only)

■ Endurance: 1,000,000 data changes

■ Data retention greater than 40 years

■ Packages available: 8-pin DIP, 8-pin SO, and 8-pin TSSOP

■ Available in three temperature ranges

- Commercial: 0° to +70°C

- Extended (E): -40° to +85C

- Automotive (V): -40° to +125°C

H.V. GENERATION

TIMING &CONTROL

E2PROM

ARRAY

YDEC

DATA REGISTER

XDEC

CONTROL

LOGIC

WORD
ADDRESS
COUNTER

SLAVE ADDRESS

REGISTER &

COMPARATOR

START

STOP

LOGIC

CK

D

IN

R/W

SDA

SCL

V

SS

WP

V

CC

D

OUT

A2

DS500071-1

2

www.fairchildsemi.com

NM24C08/09 Rev. G

NM24C08/09 – 8K-Bit Standard 2-Wire Bus Interface Serial EEPROM

NC

NC

A2

V

SS

V

CC

NC

SCL

SDA

8

7

6

5

1

2

3

4

NM24C08

Connection Diagrams

Dual-in-Line Package (N), SO Package (M8) and TSSOP Package (MT8)

See Package Number N08E, M08A and MTC08

Pin Names

A2 Device Address Input

V

SS

Ground

SDA Serial Data I/O

SCL Serial Clock Input

NC No Connection

V

CC

Power Supply

Dual-in-Line Package (N), SO Package (M8) and TSSOP Package (MT8)

See Package Number N08E, M08A and MTC08

Pin Names

A2 Device Address Input

V

SS

Ground

SDA Serial Data I/O

SCL Serial Clock input

WP Write Protect

V

CC

Power Supply

NC No Connection

NC

NC

A2

V

SS

V

CC

WP

SCL

SDA

8

7

6

5

1

2

3

4

NM24C09

DS500071-2

DS500071-3

NOTE: Pins designated as "NC" are typically unbonded pins. However some of them are bonded for special testing purposes. Hence if a signal is applied to these pins, care
should be taken that the voltage applied on these pins does not exceed the VCC applied to the device. This will ensure proper operation.

3

www.fairchildsemi.com

NM24C08/09 Rev. G

NM24C08/09 – 8K-Bit Standard 2-Wire Bus Interface Serial EEPROM

Ordering Information

NM 24 C XX F LZ E XXX Letter Description

Package N 8-pin DIP

M8 8-pin SOIC
MT8 8-pin TSSOP

Temp. Range None 0 to 70°C

V -40 to +125°C
E -40 to +85°C

Voltage Operating Range Blank 4.5V to 5.5V

L 2.7V to 5.5V
LZ 2.7V to 5.5V and

<1µA Standby Current

SCL Clock Frequency Blank 100KHz

F 400KHz

Density 08 8K

09 8K with Write Protect

C CMOS Technology

Interface 24 IIC

NM Fairchild Non-Volatile

Memory

4

www.fairchildsemi.com

NM24C08/09 Rev. G

NM24C08/09 – 8K-Bit Standard 2-Wire Bus Interface Serial EEPROM

Product Specifications

Absolute Maximum Ratings

Ambient Storage Temperature –65°C to +150°C

All Input or Output Voltages

with Respect to Ground 6.5V to –0.3V

Lead Temperature

(Soldering, 10 seconds) +300°C

ESD Rating 2000V min.

Operating Conditions

Ambient Operating Temperature

NM24C08/09 0°C to +70°C
NM24C08E/09E -40°C to +85°C
NM24C08V/09V -40°C to +125°C

Positive Power Supply

NM24C08/09 4.5V to 5.5V
NM24C08L/09L 2.7V to 5.5V
NM24C08LZ/09LZ 2.7V to 5.5V

DC Electrical Characteristics (2.7V to 5.5V)

Symbol Parameter Test Conditions Limits Units

Min Typ Max

(Note 1)

I

CCA

Active Power Supply Current f

SCL

= 400 KHz 0.2 1.0 mA

f

SCL

= 100 KHz

I

SB

Standby Current VIN = GND VCC = 2.7V - 5.5V 10 50 µA

or V

CC

VCC = 2.7V - 5.5V (L) 1 10 µA
VCC = 2.7V - 4.5V (LZ) 0.1 1 µA

I

LI

Input Leakage Current VIN = GND to V

CC

0.1 1 µA

I

LO

Output Leakage Current V

OUT

= GND to V

CC

0.1 1 µA

V

IL

Input Low Voltage –0.3 V

CC

x 0.3 V

V

IH

Input High Voltage VCC x 0.7 VCC + 0.5 V

V

OL

Output Low Voltage IOL = 3 mA 0.4 V

Capacitance T

A

= +25°C, f = 100/400 KHz, VCC = 5V (Note 2)

Symbol Test Conditions Max Units

C

I/O

Input/Output Capacitance (SDA) V

I/O

= 0V 8 pF

C

IN

Input Capacitance (A0, A1, A2, SCL) VIN = 0V 6 pF

Note 1: Typical values are TA = 25°C and nominal supply voltage of 5V for 4.5V-5.5V operation and at 3V for 2.7V-4.5V operation.

Note 2: This parameter is periodically sampled and not 100% tested.

5

www.fairchildsemi.com

NM24C08/09 Rev. G

NM24C08/09 – 8K-Bit Standard 2-Wire Bus Interface Serial EEPROM

AC Test Conditions

Input Pulse Levels VCC x 0.1 to VCC x 0.9

Input Rise and Fall Times 10 ns

Input & Output Timing Levels VCC x 0.3 to VCC x 0.7

Output Load 1 TTL Gate and C

L

= 100 pF

Bus Timing

DS500071-5

SCL

SDA

IN

SDA

OUT

t

F

t

LOW

t

HIGH

t

R

t

LOW

t

AA

t

DH

t

BUF

t

SU:STA

t

HD:DAT

t

HD:STA

t

SU:DAT

t

SU:STO

0.9VCC

0.1VCC

0.7VCC

0.3VCC

Read and Write Cycle Limits (Standard and Low VCC Range 2.7V - 5.5V)

Symbol Parameter 100 KHz 400 KHz Units

Min Max Min Max

f

SCL

SCL Clock Frequency 100 400 KHz

T

I

Noise Suppression Time Constant at
SCL, SDA Inputs (Minimum V

IN

100 50 ns

Pulse width)

t

AA

SCL Low to SDA Data Out Valid 0.3 3.5 0.1 0.9 µs

t

BUF

Time the Bus Must Be Free before 4.7 1.3 µs
a New Transmission Can Start

t

HD:STA

Start Condition Hold Time 4.0 0.6 µs

t

LOW

Clock Low Period 4.7 1.5 µs

t

HIGH

Clock High Period 4.0 0.6 µs

t

SU:STA

Start Condition Setup Time 4.7 0.6 µs
(for a Repeated Start Condition)

t

HD:DAT

Data in Hold Time 20 20 ns

t

SU:DAT

Data in Setup Time 250 100 ns

t

R

SDA and SCL Rise Time 1 0.3 µs

t

F

SDA and SCL Fall Time 300 300 ns

t

SU:STO

Stop Condition Setup Time 4.7 0.6 µs

t

DH

Data Out Hold Time 300 50 ns

t

WR

Write Cycle Time - NM24C08/09 10 10 ms

(Note 3) - NM24C08/09L, NM24C08/09LZ 15 15

Note 3: The write cycle time (tWR) is the time from a valid stop condition of a write sequence to the end of the internal erase/program cycle. During the write cycle, the
NM24C08/09 bus interface circuits are disabled, SDA is allowed to remain high per the bus-level pull-up resistor, and the device does not respond to its slave address. Refer
"Write Cycle Timing" diagram.

AC Testing Input/Output Waveforms

DS500071-4