Fairchild Semiconductor FSTU16862 Datasheet
FSTU16862
FSTU16862 20-Bit Bus Switch with
May 2002
Revised May 2002
20-Bit Bus Switch with
General Description
The Fairchild Switc h FSTU16862 provides 20-bi ts of highspeed CMOS TTL-compatible bus switching. The low On
Resistance of the switch allows inputs to be connected to
outputs without adding propagation delay or generating
additional ground bounce noise.
The device is organ ized as a 20 -bi t bus sw itch. When OE
is LOW, the switch is ON and Port A is connected to Port B.
When OE
between the A and B P orts. The A and B Ports a re pro-
tected against undershoo t to su ppo rt an extended range to
2.0V below ground. Fairchild’s integrated Undershoot
Hardened Circuit (UHC
and responds by preventing voltage differentials from
developing and turning the switch on.
is HIGH, a high impedance state exists
X
) senses undershoot at the I/O
−2V Undershoot Protection
Features
■ Undershoot hardened to −2V (A and B Ports)
Ω switch connection between two ports
■ 4
■ Minimal propagation delay through the switch
■ Low l
CC
■ Zero bounce in flow-through mode
X
■ Control inputs compatible with TTL level
■ See Application Note AN-5008 for details on
FSTU - Undershoot Protected Fairchild Switch Family
Ordering Code:
Order Number
FSTU16862QSP MQA48A 48-Lead Quarter Size Very Small Outline Package (QVSOP), JEDEC MO-154, 0.150" Wide
FSTU16862MTD MTD48 48-Lead Thin Shrink Small Outline Package (TSSOP), JEDEC MO-153, 6.1mm Wide
Devices also availab l e in Tape and Reel. Specify by appending th e s uffix let t er “X” to the ordering code.
Package
Number
Package Descript ion
−
2V Undershoot Protection
UHC is a trademark of Fairchild Semiconductor Corporation.
© 2002 Fairchild Semiconductor Corporation DS500703 www.fairchildsemi.com
Logic Diagram
FSTU16862
Pin Descriptions
Pin Name Description
OE
Truth Table
Inputs Inputs/Outputs
OE
H = HIGH Voltage Level
L = LOW Voltage Level
Z = High Impedance
x
ABus A
BBus B
x
LA
HZ
Bus Switch Enables
A, B
= B
Connection Diagram
www.fairchildsemi.com 2
Absolute Maximum Ratings(Note 1) Recommended Operating
Supply Voltage (VCC) −0.5V to +7.0V
DC Switch Voltage (V
DC Input Voltage (V
DC Input Diode Current (l
DC Output Current (I
DC V
/GND Current (ICC/I
CC
Storage Temperature Range (T
) (Note 2) −2.0V to +7.0V
S
) (Note 3) −0.5V to +7.0V
IN
) V
< 0V −50 mA
IK
IN
)128 mA
OUT
) ±100 mA
GND
) −65°C to +150 °C
STG
Conditions
Power Supply Operating (V
Input Voltage (V
Output Voltage (V
Input Rise and Fall Time (t
Switch Control Input 0 ns/V to 5 ns/V
Switch I/O 0 ns/V to DC
Free Air Operating Temperature (T
Note 1: The “Absolute Maximum Ratings” are those value s beyond which
the safety of the d evice cannot b e guaranteed . The device sh ould not be
operated at these limit s. The parametric values defi ned in the Electrical
Characteristics tables are not guaranteed at the absolute maximum rating.
The “Recomm ended O peratin g Cond itions ” table will defin e the condition s
for actual device operation.
is the volt age observed / applied at either the A or B Ports across
Note 2: V
S
the switch.
Note 3: The input and output negative voltage ratings may be exceeded if
the input and ou t put diode curre nt ratings are observed.
Note 4: Unused control inputs must be held HIGH or LOW. They may not
float.
(Note 4)
CC)
) 0V to 5.5V
IN
) 0V to 5.5V
OUT
, tf)
r
)-40 °C to +85 °C
A
4.0V to 5.5V
DC Electrical Characteristics
V
Symbol Parameter
V
IK
V
IH
V
IL
I
I
I
OZ
R
ON
I
CC
∆ I
V
IKU
Note 5: Typical values are at VCC = 5.0V and TA = +25°C
Note 6: Measured by the voltage drop between A and B pins at the indicated c urrent through the switch. On Resistanc e is determined by the lower of the
voltages on the two (A or B) pins.
Note 7: Per TTL driven input, control pins only.
Clamp Diode Voltage 4.5 −1.2 V IIN = −18 mA
HIGH Level Input Voltage 4.0–5.5 2.0 V
LOW Level Input Voltage 4.0–5.5 0.8 V
Input Leakage Current 5.5 ±1.0 µA0 ≤ VIN ≤ 5.5V
OFF-STATE Leakage Current 5.5 ±1.0 µA0 ≤ A, B ≤ V
Switch On Resistance 4.5 4 7 Ω VIN = 0V, IIN = 64 mA
(Note 6) 4.5 4 7 Ω V
Quiescent Supply Current 5.5 3 µAVIN = VCC or GND, I
Increase in I
CC
(Note 7) Other Inputs at VCC or GND
Voltage Undershoot 5.5 −2.0 V 0.0 mA ≥ I
per Input 5.5 2.5 mA One Input at 3.4V
CC
CC
(V) Min Typ
010µAV
4.5 8 14 Ω V
4.0 11 20 Ω VIN = 2.4V, IIN = 15 mA
TA = −40 °C to +85 °C
(Note 5)
Max
Units Conditions
= 5.5V
IN
CC
= 0V, IIN = 30 mA
IN
= 2.4V, IIN = 15 mA
IN
≥ −50 mA
IN
= 5.5V
OE
OUT
FSTU16862
= 0
3 www.fairchildsemi.com
Loading...