Fairchild Semiconductor FM24C64FLZ Datasheet

1

www.fairchildsemi.com

FM24C64 Rev. C

FM24C64 – 64K-Bit Standard 2-Wire Bus Interface Serial EEPROM

December 2001

© 2001 Fairchild Semiconductor Corporation

FM24C64 – 64K-Bit Standard 2-Wire Bus
Interface Serial EEPROM

General Description

FM24C64 is a 64Kbit CMOS non-volatile serial EEPROM orga­nized as 8K x 8 bit memory. This device confirms to Extended IIC
2-wire protocol that allows accessing of memory in excess of
16Kbit on an IIC bus. This serial communication protocol uses a
Clock signal (SCL) and a Data signal (SDA) to synchronously
clock data between a master (e.g. a microcontroller) and a slave
(EEPROM). FM24C64 is designed to minimize pin count and
simplify PC board layout requirements.

FM24C64 offers hardware write protection where by the entire
memory array can be write protected by connecting WP pin to VCC.
This section of memory then becomes unalterable until the WP pin
is switched to VSS.

“LZ” and “L” versions of FM24C64 offer very low standby current
making them suitable for low power applications. This device is
offered in SO, TSSOP and DIP packages.

Fairchild EEPROMs are designed and tested for applications
requiring high endurance, high reliability and low power consump­tion.

Block Diagram

Features

■ Extended operating voltage: 2.5V to 5.5V

■ Up to 400 KHz clock frequency at 2.5V to 5.5V

■ Low power consumption

— 0.5mA active current typical
—10µA standby current typical
—1µA standby current typical (L version)
— 0.1µA standby current typical (LZ version)

■ Schmitt trigger inputs

■ 32 byte page write mode

■ Self timed write cycle (6ms typical)

■ Hardware Write Protection for the entire array

■ Endurance: up to 100K data changes

■ Data Retention: Greater than 40 years

■ Packages: 8-Pin DIP, 8-Pin SO and 8-Pin TSSOP

■ Temperature range

— Commercial: 0°C to +70°C
— Industrial (E): -40°C to +85°C
— Automotive (V): -40°C to +125°C

H.V. GENERATION

TIMING &CONTROL

E2PROM

ARRAY

YDEC

DATA REGISTER

XDEC

CONTROL

LOGIC

WORD
ADDRESS
COUNTER

SLAVE ADDRESS

REGISTER &

COMPARATOR

START

STOP

LOGIC

WRITE

LOCKOUT

CK

D

IN

R/W

SDA

SCL

WP

V

CC

V

SS

D

OUT

A2
A1
A0

2

www.fairchildsemi.com

FM24C64 Rev. C

FM24C64 – 64K-Bit Standard 2-Wire Bus Interface Serial EEPROM

A0

A1

A2

V

SS

V

CC

WP

SCL

SDA

8

7

6

5

1

2

3

4

FM24C64

Connection Diagram

Dual-in-Line Package (N), SO Package (M8) and TSSOP Package (MT8)

See Package Number N08E, M08A and MTC08

Pin Names

V

SS

Ground

SDA Serial Data I/O

SCL Serial Clock Input

WP Write Protect

V

CC

Power Supply

A0, A1, A2 Device Address Inputs

3

www.fairchildsemi.com

FM24C64 Rev. C

FM24C64 – 64K-Bit Standard 2-Wire Bus Interface Serial EEPROM

Ordering Information

FM 24 C XX F LZ E YY X Letter Description

Blank Tube
X Tape and Reel

Package N 8-pin DIP

M8 8-pin SOIC
MT8 8-pin TSSOP

Temp. Range Blank 0 to 70°C

E -40 to +85°C
V -40 to +125°C

Voltage Operating Range Blank 4.5V to 5.5V

L 2.5V to 5.5V
LZ 2.5V to 5.5V and

<1µA Standby Current

SCL Clock Frequency Blank 100KHz

F 400KHz

Density 64 64K with write protect

C CMOS

Interface 24 IIC - 2 Wire

FM Fairchild Non-Volatile

Memory

4

www.fairchildsemi.com

FM24C64 Rev. C

FM24C64 – 64K-Bit Standard 2-Wire Bus Interface Serial EEPROM

Product Specifications

Absolute Maximum Ratings

Ambient Storage Temperature –65°C to +150°C

All Input or Output Voltages

with Respect to Ground 6.5V to –0.3V

Lead Temperature

(Soldering, 10 seconds) +300°C

ESD Rating 2000V min.

Operating Conditions

Ambient Operating Temperature

FM24C64 0°C to +70°C
FM24C64E -40°C to +85°C
FM24C64V -40°C to +125°C

Positive Power Supply

FM24C64 4.5V to 5.5V
FM24C64L 2.5V to 5.5V
FM24C64LZ 2.5V to 5.5V

Standard VCC (4.5V to 5.5V) DC Electrical Characteristics

Symbol Parameter Test Conditions Limits Units

Min Typ Max

(Note 1)

I

CCA

Active Power Supply Current f

SCL

= 400 KHz 0.5 1.0 mA

f

SCL

= 100 KHz

I

SB

Standby Current VIN = GND or V

CC

10 50 µA

I

LI

Input Leakage Current VIN = GND to V

CC

0.1 1 µA

I

LO

Output Leakage Current V

OUT

= GND to V

CC

0.1 1 µA

V

IL

Input Low Voltage –0.3 VCC x 0.3 V

V

IH

Input High Voltage VCC x 0.7 VCC + 0.5 V

V

OL

Output Low Voltage I

OL

= 2.1 mA 0.4 V

Low VCC (2.5V to 5 .5V) DC Electrical Characteristics

Symbol Parameter Test Conditions Limits Units

Min Typ Max

(Note 1)

I

CCA

Active Power Supply Current f

SCL

= 400 KHz 0.5 1.0 mA

f

SCL

= 100 KHz

I

SB

Standby Current VIN = GND VCC = 2.5V - 4.5V (L) 1 10 µA

(Note 3) or V

CC

VCC = 2.5V - 4.5V (LZ) 0.1 1 µA
VCC = 4.5V - 5.5V 10 50 µA

I

LI

Input Leakage Current VIN = GND to V

CC

0.1 1 µA

I

LO

Output Leakage Current V

OUT

= GND to V

CC

0.1 1 µA

V

IL

Input Low Voltage –0.3 V

CC

x 0.3 V

V

IH

Input High Voltage VCC x 0.7 VCC + 0.5 V

V

OL

Output Low Voltage IOL = 2.1 mA 0.4 V

Capacitance T

A

= +25°C, f = 100/400 KHz, VCC = 5V (Note 2)

Symbol Test Conditions Max Units

C

I/O

Input/Output Capacitance (SDA) V

I/O

= 0V 8 pF

C

IN

Input Capacitance (A0, A1, A2, SCL) VIN = 0V 6 pF

Note 1: Typical values are TA = 25°C and nominal supply voltage (5V).

Note 2: This parameter is periodically sampled and not 100% tested.

Note 3: The "L" and "LZ" versions can be operated in the 2.5V to 5.5V VCC range. However the ISB values for L and LZ are applicable only when VCC is in the 2.5V to 4.5V range.