Fairchild QTLP610CIR service manual
)
)
)
)
)
)
)
)
)
K
T
OP
CK
)
)
)
)
Y
RIGHT ANGLE SURFACE
MOUNT INFRARED
EMITTING DIODE
QTLP610CIR
PACKAGE DIMENSIONS
0.126 (3.2
0.110 (2.8
0.043 (1.1
0.035 (0.9
FRON
0.020 (0.50
0.087 (2.2
0.071 (1.8
0.039 (1.0
T
0.035 (0.9
POLARITY MAR
BA
0.016 (0.4
POLARIT
NOTE:
1. Cathode
2. Anode
3. Dimensions for all drawings are in inches (mm).
FEATURES
0.087 (2.2
0.071 (1.8
R0.017 (0.4
• Right Angle Surface Mount Package
• Available in 0.315” (8mm) width tape on 7” (178mm) diameter reel; 2,000 units per reel
• Wide Viewing Angle 160°
• Wavelength = 940 nm, GaAs
• Water Clear Lens
• Matched Photosensor: QTLP610CPD
© 2003 Fairchild Semiconductor Corporation
Page 1 of 6
1/5/04
λ
Θ
RIGHT ANGLE SURFACE
MOUNT INFRARED
EMITTING DIODE
QTLP610CIR
(T
ABSOLUTE MAXIMUM RATINGS
Parameter Symbol Rating Unit
= 25°C unless otherwise specified)
A
Operating Temperature T
Storage Temperature T
Soldering Temperature (Iron)
Soldering Temperature (Flow)
(1,2,3)
(1,2)
Continuous Forward Current I
Reverse Voltage V
Power Dissipation
(4)
Peak Forward Current (Pulse width = 100µs, Duty Cycle=1%) I
Notes:
1. RMA flux is recommended.
2. Methanol or isopropyl alcohols are recommended as cleaning agents.
3. Soldering iron tip at 1/16" (1.6mm) from housing
4. At 25°C or below
ELECTRICAL / OPTICAL CHARACTERISTICS
(T
A
=25°C)
PARAMETER TEST CONDITIONS SYMBOL MIN. TYP. MAX. UNITS
Peak Emission Wavelength I
Emission Angle I
Forward Voltage
Reverse Current V
Radiant Intensity
Rise Time I
Fall Time t
= 20 mA
F
= 20 mA
F
I
= 20 mA
F
= 100 mA, t
F
I
= 1 A, t
F
= 5 V I
R
I
= 20 mA
F
= 100 mA, t
F
I
= 1 A, t
F
= 100 mA t
F
= 20 ms t
P
= 100 µs, Duty Cycle = 0.01 — 1.4 1.85
P
= 100 µs, Duty Cycle = 0.01 — 2.6 4.0
P
= 100 µs, Duty Cycle = 0.01 — 4.0 —
P
= 100 µs, Duty Cycle = 0.01 — 40 —
P
T
SOL-I
T
SOL-F
OPR
STG
-40 to +85 °C
-40 to +90 °C
240 for 5 sec °C
260 for 10 sec °C
F
R
P
D
FD
65 mA
5V
100 mW
1.0 A
P — 940 — nm
— ±80 — Deg.
— 1.2 1.5
V
F
R
——10 µA
0.5 0.8 —
Ee
r
f
— 1 — µs
— 1 — µs
VI
mW/srI
© 2003 Fairchild Semiconductor Corporation
Page 2 of 6
1/5/04
Loading...