Fairchild FSA3357 User Manual

Page 1
FSA3357 Low Voltage SP3T Analog Switch
(3:1 Multiplexer/Demultiplexer)
FSA3357 Low Voltage SP3T Analog Switch (3:1 Multiplexer/Demultiplexer)
December 2002 Revised August 2005
General Description
operating range.
CC
, B1, or B2 Ports due to the
0
CC
Features
O
Useful in both analog and digital applications
O
Space saving US8 8-lead surface mount package
O
Low On Resistance; 9: on typ @ 3.3V V
O
Broad VCC operating range; 1.65V to 5.5V
O
Rail-to-Rail signal handling
O
Power down high impedance control input
O
Overvoltage tolerance of control input to 7.0V
O
Break before make enable circuitry
O
250 MHz - 3dB bandwidth
O
Space saving Pb-Free MicroPak¥ packaging
CC
Applications
O
Cell Phone
O
PDA
O
Video
Ordering Code:
Product
Package Description Supplied AsOrder Package Code
Number Number Top Mark
FSA3357K8X MAB08A A357 8-Lead US8, JEDEC MO-187, Variation CA 3.1mm Wide 3k Units on Tape and Reel FSA3357L8X MAC08A FE Pb-Free 8-Lead MicroPak, 1.6 mm Wide 5k Units on Tape and Reel
Pb-Free package per JEDEC J-STD-020B.
MicroPak¥ is a trademark of Fairchild Semiconductor Corporation.
© 2005 Fairchild Semiconductor Corporation DS500805 www.fairchildsemi.com
Page 2
Analog Symbols
Connection Diagram
FSA3357
Pin Assignments for US8
(Top View)
Pin Assignments for MicroPak
(T op Through View)
Pin Descriptions
Pin Names Description
A1, B0, B1, B
S
2
, S
1
2
Function Table
S
1
0 0 No Connection 10B 01B 11B
S
(Top View)
2
Data Ports
Control Input
Function
Connected to A
0
Connected to A
1
Connected to A
2
www.fairchildsemi.com 2
Page 3
FSA3357
Absolute Maximum Ratings(Note 1)
Supply Voltage (VCC) DC Switch Voltage (V
DC Input Voltage (V DC Input Diode Current (I
@ (I
) VIN 0V
IK
DC Output Current (I
or Ground Current (ICC/I
DC V
CC
Storage Temperature Range (T Junction Temperature under Bias (T Junction Lead Temperature (T
) (Note 2)
S
) (Note 2)
IN
)
IK
) 128 mA
OUT
)
GND
)
STG
) 150qC
J
)
L
(Soldering, 10 seconds) 260
Power Dissipation (P
) @ 85qC180 mW
D
0.5V to 7.0V
0.5V to 7.0V
65q
C to 150qC
DC Electrical Characteristics
0.5V to V
50 mA
r
100 mA
CC
0.5V
q
Recommended Operating Conditions
(Note 3)
Supply Voltage Operating (V Control Input Voltage (V Switch Input Voltage (VIN)0V to V Output Voltage (V
)0V to V
OUT
Operating Temperature (TA) Input Rise and Fall Time (t
Control Input V Control Input V
Thermal Resistance (
C
MicroPak 8L Package 224
Note 1: Absolute maximum ratings are DC values beyond which the device may be damaged or have its useful life imp ai red. The dat ashee t speci ficati on s should be m et, without exception, to ensure that the system design is reliable over its power supply, temperature, and output/input loading variables. Fairchild does not recommend oper­ation outside datasheet specifications.
Note 2: The input and output negative voltage ratings may be exceeded if the input and output diode current ratings are observed.
Note 3: Control inputs must be held HIGH or LOW, they must not float.
= 2.3V - 3.6V 0 ns/V to 10 ns/V
CC
= 4.5V - 5.5V 0 ns/V to 5 ns/V
CC
T
) 1.65V to 5.5V
CC
)0V to V
IN
, tf)
r
) 250qC/W
JA
40q
CC CC CC
C to 85qC
q
C/W
Symbol Parameter
V
IH
V
IL
I
IN
I
OFF
R
ON
I
CC
ASR Analog Signal Range V
'
R
R
flat
HIGH Level 1.65 1.95 0.75 V Input Voltage 2.3 5.5 0.7 V LOW Level 1.65 1.95 0.25 V Input Voltage 2.3 5.5 0.3 V Input Leakage Current 0 5.5 OFF State Leakage Current 1.65 5.5 Switch On Resistance 4.5 5.0 7.0 7.0 (Note 4) 6.0 12.0 12.0 VIN = 2.4V, IO = 30 mA
Quiescent Supply Current All Channels ON or OFF I
On Resistance Match 4.5 0.15
ON
Between Channels 3.0 0.22 IA = 24 mA, VBn = 2.1 (Note 4)(Note 5)(Note 6) 2.3 0.31 IA = 8 mA, VBn = 1.6
On Resistance Flatness 5.0 6.0 (Note 4)(Note 5)(Note 7) 3.3 12.0 IA = 24 mA, 0 d V
V
CC
(V) Min Typ Max Min Max
3.0 6.5 9.0 9.0 VIN = 0V, IO = 24 mA
2.3 8.0 12.0 12.0 VIN = 0V, IO = 8 mA
1.65 10.0 20.0 20.0 VIN = 0V, IO = 4 mA
5.5 1.0 10.0
CC
1.65 0.62 IA = 4 mA, VBn = 1.15
2.5 40.0 IA = 8 mA, 0 d V
1.8 140.0 IA = 4 mA, 0 d V
TA = 25qCT
CC
CC
CC
CC
r
0.1
r
0.1
7.0 15.0 15.0 VIN = 4.5V, IO = 30 mA
9.0 20.0 20.0 VIN = 3V, IO = 24 mA
11.0 30.0 30.0 VIN = 2.3V, IO = 8 mA
17.0 50.0 50.0 VIN = 1.65V, IO = 4 mA
0.0 V
CC
= 40qC to 85qC
A
0.75 V
CC
0.7 V
CC
0.0 V
0.25 V
0.3 V
r
r
1.0
1.0
Units Conditions
V
CC
V
CC
P
A0 d VIN d 5.5V
P
A0 d A, Bn d V
:
P
A
CC
V
:
:
CC
VIN = 0V, IO = 30 mA
VIN = VCC or GND
= 0
OUT
IA = 30 mA, VBn = 3.15
IA = 30 mA, 0 d V
Bn
Bn
Bn
Bn
d
V
CC
d
V
CC
d
V
CC
d
V
CC
3 www.fairchildsemi.com
Page 4
DC Electrical Characteristics (Continued)
Note 4: Measured by the voltage drop between A and Bn pins at the indicated current through the switch. On Resistance is determined by the lower of the voltages on the two (A
Ports).
or B
FSA3357
n
Note 5: Parameter is characterized but not tested in production. Note 6: 'R
= RON max RON min measured at identical VCC, temperature and voltage levels.
ON
Note 7: Flatness is defined as the difference between the maximum and minimum value of On Resistance over the specified range of conditions.
AC Electrical Characteristics
Symbol Parameter
t t
PHL
PLH
Propagation Delay 1.65 1.95 2.0 Bus to Bus 2.3 2.7 1.1
V
CC
(V) Min Typ Max Min Max Number
TA = 25qCT
(Note 8) 3.0 3.6 0.7
4.5 5.5 0.4 t t
PZL
PZH
Output Enable Time 1.65 1.95 5.0 32.0 5.0 34.0 Turn on Time 2.3 2.7 3.0 15.0 3.0 16.5 VI = 2 x VCC for t (A to Bn)3.0
3.6 2.0 9.5 2.0 11.0 VI = 0V for t
4.5 5.5 1.5 6.5 1.5 7.0 t t
PLZ
PHZ
Output Disable Time 1.65 1.95 3.0 14.0 3.0 14.5 Turn Off Time 2.3 2.7 2.0 7.2 2.0 7.8 VI = 2 x V (A Port to Bn Port) 3.0 3.6 1.5 5.1 1.5 5.5 VI = 0V for t
4.5 5.5 0.8 3.7 0.8 4.0 t
B-M
Break Before Make Time 1.65 1.95 0.5 0.5 (Note 9) 2.3 2.7 0.5 0.5
3.0 3.6 0.5 0.5
4.5 5.5 0.5 0.5 Q Charge Injection (Note 9) 5.0 3.0
3.3 2.0 R
OIRR Off Isolation (Note 10) 1.65 5.5
Xtalk Crosstalk 1.65 5.5
BW
3dB Bandwidth 1.65 5.5 250.0 MHz RL = 50
58.0
60.0
THD Total Harmonic Distortion
(Note 9) 0.5 V
5.0 .01 %
= 40qC to 85qC
A
PZL
Figure
Figures
Figures
Figures
Units Conditions
ns VI = OPEN
ns
ns
CC
PZH
for t
PHZ
PLZ
ns Figure 3
pC
dB
dB
CL = 0.1 nF, V
= 0
GEN
RL = 50 f = 10MHz RL = 50 f = 10MHz
RL = 600
P-P
= 0V
GEN
:
:
:
:
Figure 4
Figure 5
Figure 6
Figure 9
:
f = 600 Hz to 20 KHz
1, 2
1, 2
1, 2
Note 8: This parameter is guaranteed by design but not tested. The bus switch contributes no propagation delay other than the RC delay of the On Resistance of the switch and the 50 pF load capacitance, when driven by an ideal voltage source (zero output impedance).
Note 9: Guaranteed by Design. Note 10: Off Isolation = 20 log10 [VA / VBn]
Capacitance (Note 11)
Symbol Parameter Typ Max Units Conditions
C
IN
C
IO-B
C
IOA-ON
Note 11: TA = 25qC, f = 1 MHz, Capacitance is characterized but not tested in production.
www.fairchildsemi.com 4
Control Pin Input Capacitance 2.0 pF VCC = 0V B Port Off Capacitance 3.6 pF VCC = 5.0V Figure 7 A Port Capacitance When Switch Is Enabled 14.5 pF VCC = 5.0V Figure 8
Figure
Number
Page 5
AC Loading and Waveforms
FSA3357
Note: Input driven by 50: source terminated in 50 Note: C
includes load and stray capacitance
L
Note: Input PRR = 1.0 MHz; t
= 500 ns
W
:
FIGURE 1. AC Test Circuit
FIGURE 2. AC Waveforms
FIGURE 3. Break Before Make Interval Timing
5 www.fairchildsemi.com
Page 6
AC Loading and Waveforms (Continued)
FSA3357
FIGURE 4. Charge Injection Test
FIGURE 5. Off Isolation
FIGURE 7. Channel Off Capacitance
FIGURE 6. Crosstalk
FIGURE 8. Channel On Capacitance
FIGURE 9. Bandwidth
www.fairchildsemi.com 6
Page 7
Tape and Reel Specification
TAPE FORMAT for US8
Package Tape Number Cavity Cover Tape
Designator Section Cavities Status Status
Leader (Start End) 125 (typ) Empty Sealed
K8X Carrier 250 Filled Sealed
Trailer (Hub End) 75 (typ) Empty Sealed
TAPE DIMENSIONS inches (millimeters)
FSA3357
REEL DIMENSIONS inches (millimeters)
Tape
ABCDN W1 W2 W3
Size
7.0 0.059 0.512 0.795 2.165 0.331
8 mm
(177.8) (1.50) (13.00) (20.20) (55.00) (8.40
0.059/
0.000
1.50/0.00) (14.40) (W1 2.00/1.00)
0.567 W1
0.078/0.039
7 www.fairchildsemi.com
Page 8
TAPE FORMAT for MicroPak
FSA3357
Package Tape Number Cavity Cover Tape
Designator Section Cavities Status Status
Leader (Start End) 125 (typ) Empty Sealed
L8X Carrier 5000 Filled Sealed
Trailer (Hub End) 75 (typ) Empty Sealed
REEL DIMENSIONS inches (millimeters)
Tape SizeABCDN W1 W2 W3
8 mm
www.fairchildsemi.com 8
7.0 0.059 0.512 0.795 2.165 0.331
(177.8) (1.50) (13.00) (20.20) (55.00) (8.40
0.059/0.000 0. 567 W1 0.078/0.039
1.50/0.00) (14.40) (W1 2.00/1.00)
Page 9
Physical Dimensions inches (millimeters) unless otherwise noted
FSA3357
8-Lead US8, JEDEC MO-187, Variation CA 3.1mm Wide
Package Number MAB08A
9 www.fairchildsemi.com
Page 10
Physical Dimensions inches (millimeters) unless otherwise noted (Continued)
FSA3357
Pb-Free 8-Lead MicroPak, 1.6 mm Wide
Package Number MAC08A
www.fairchildsemi.com 10
Page 11
FSA3357 Low Voltage SP3T Analog Switch (3:1 Multiplexer/Demultiplexer)
DISCLAIMER
FAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO ANY PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTI ON OR DESIGN. FAIRCHILD DOES NOT ASSUME ANY LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCT OR CIRCUIT DESCRIBED HEREIN; NEITHER DOES IT CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS.
LIFE SUPPORT POLICY
FAIRCHILD’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF FAIRCHILD SEMICONDUCTOR CORPORATION
As used herein:
1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, or (c) whose failure to perform when properly used in accordance with instructions for use
provided in the labeling, can be reasonably expected to result in significant injury to the user.
2. A critical component is any component of a life support device or system whose failure to perform can be reason­ably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness.
PRODUCT STATUS DEFINITIONS
Definition of terms
Datasheet Identification Product Status Definition
Advance Information F orm ativ e or In Design This datasheet contains the design specifications for product develop-
Preliminary First Produc tion This datasheet contains preliminary data, and supplementary data will
No Identification Needed Full Production This datasheet contains final specifications. Fairchild Semiconductor
Obsolete Not In Production T his datasheet contains specifications on a product that has been dis-
ment. Specifications may change in any manner without notice.
be published at a later date. Fairchild Semiconductor reserves the right to make changes at any time without notice in order to improve design.
reserves the right to make changes at any time without notice in order to improve design.
continued by Fairchild Semiconductor. The datasheet is printed for ref­erence information only.
11 www.fairchildsemi.com
Loading...