How it Works
Fagerhult
Loading...
#
E
Loading...
Loading...
86371
User Manual
23 pgs4.23 Mb0

Fagerhult e-Sense Series, 86370, 86371 User Manual

Download
e-Sense Customised Stand-alone
Lorem ipsum
Subject to change without notice. Version1_20180621
Mechanical cut-o, functions ............................................................................................................................................... 4
Programming for personal settings ..............................................................................................................................9–10
Reduced power, Standby dimming level............................................................................................................................. 11
Delay times, Standby time ..................................................................................................................................................... 12
On/O, Auto Mode ......................................................................................................................................................................13
Lux Threshold ............................................................................................................................................................................. 14
Shift button, Test function, Manual switch-on ...............................................................................................................15
Daylight control ......................................................................................................................................................................... 16
Dual sensor technology ....................................................................................................................................................17–18
Wiring examples ..................................................................................................................................................................19 –21
Technical specication ........................................................................................................................................................... 22
Contents
3
Subject to change without notice. Version1_20180621
86370 and 86371 are sensors for individual installation in ceilings. 86370 is most suitable for surfaces with a ceiling height of max. 6 metres, while 86371 can detect higher heights up to 12 metres. 86371 also has two lenses for the best detection
with the PIR sensor. The sensor has a range of settings in order to optimise all functions:
• Choice of detection PIR or Microwave sensor, or a combination of these.
• Integrated power supply for connecting 20 DALI loads.
• Sync where several sensors can work together e.g. in a corridor.
• Pushbutton connection for manual control of light level.
• Daylight sensor for adjustment according to incident daylight.
• Lux threshold prevents the light from switching on when the lighting conditions have already been met.
• Choice of 16 dierent xed function combinations on the sensor.
• Choice of sensor technology on the sensor.
• Programming with remote control 86368.
• Quick programming of all function selections with 86368.
• Installation in ceiling panel (A-socket) or surface mounted in the accompanying socket.
• Lens for limiting the PIR detection range.
• Setting the sensitivity of the microwave sensor’s detection range.
• For installation with socket in the ceiling panel use accessory 86393.
e-Sense Customised Stand-alone sensors – 86370 and 86371
4
Subject to change without notice. Version1_20180621
Sensor can be placed on a suitable base or surface moun-
ted or recessed. When using the microwave sensor, a
stable base is important.
The sensor is supplied with an installation socket for sur­face mounted installation. Four lead-in throughs.
If you remove the socket, the sensor can be installed re­cessed in standard A-socket for 60 mm holes.
Installation
5
PIR
Photocell
LED indicator
Sensor mode selection
Rotary switch preset
HF Sensor module
Infrared receiver
Subject to change without notice. Version1_20180621
The sensor is also supplied with mechanical cut-o which
can limit the detection range. NOTE! Only if you use the PIR sensor.
e-Sense Stand-alone is a exible sensor that has several
options to optimise the function.
• PIR sensor for detecting reected heat (people).
• Microwave sensor that detects movement even th­rough walls and glass.
• Light sensor for setting the lux threshold and/or
daylight level.
• IR receiver for programming with remote control.
• Mode switch for selection of sensor technology
• Rotary switch for setting the nished functions ac­cording to the table.
Mechanical cut-o
Functions
6
Subject to change without notice. Version1_20180621
The rotary switch on the sensor is for selecting a nished package with presets. The functions are according to the
table below. The functions can always be changed in detail with remote control 86368. If you then use the rotary
switch again, it is that setting that applies. The sensor is
supplied with setting mode 0 which 5 min after the last
presence is detected adjusts to 10%, and 5 min until it switches o.
Preset functions
Settings rotary switch on 86370 and 86371
Selection of preset 1-F Detection Delay time Standby time Standby dimming level Daylight Threshold
0 100 % 5 min 5 min 10 % Disabled
1 100 % 5 sec 10 s 10 % Disabled
2 100 % 5 min 10 min 10 % Disabled
3 100 % 5 min +
∞
10 % Disabled
4 100 % 5 min +
∞
10 % Disabled
5 100 % 5 min +
∞
30 % Disabled
6 100 % 10 min 30 min 10 % Disabled
7 100 % 10 min +
∞
10 % LOW
8 100 % 10 min +
∞
10 % LOW
9 100 % 10 min +
∞
30 % MID
A 100 % 20 min 1 h 10 % Disabled
B 100 % 20 min +
∞
30 % MID
C 100 % 30 min +
∞
10 % Disabled
D 100 % 30 min +
∞
30 % MID
E 100 % 30 min +
∞
50 % HIGH
F 100 % 5 sec 10 s 10 % HIGH
PIR
Photocell
LED indicator
Sensor mode selection
Rotary switch preset
HF Sensor module
Infrared receiver
7
Subject to change without notice. Version1_20180621
Sensors 86370 and 86371 have the option to select two dierent technologies to detect presence. The microwave sensor does not generally just detect movement from
people and it can detect through walls and glass. The PIR
sensor only detects infrared heat radiation (human heat)
in motion. Choosing one of the sensor technologies or a
combination of the sensors provide great opportunities to
easily optimise control functions.
Using the red mode switch on the sensor, you can select the sensor technology function – PIR sensor or Microwave
sensor. It is also possible to perform two combinations of
both technologies. If you use the remote control, you can
use it to change the settings.
I Both of the switches in the ON position:
Microwave sensor
II Switch 2 in ON position: Only PIR sensor
III Switch 1 in ON position: Microwave sensor + PIR
sensor (both of the sensors must detect in order for
the light to switch on). IV Both of the switches in the OFF position: Microwave
sensor/PIR sensor (either of the sensors switches the
light on).
Choice of sensor technology
8
Shift
ON
OFF
AUTO MODE
DEFAULT
Start
LOW MID
Save
Apply
10% 50% 75%
POWER
100%
POWER
80%
100%
Disable
20 min
HIGH
MANUAL ON MODE
MANUAL SETTING
10 min1 min
Test
2 S
30 min15 min5 min30 s
1 min
20% 30% 50%10%
10 min
RX
STBY%
MW/PIR
RX
100%
MW+PIR
Send
PIR
Learn/
Erase
MW
5 min10 s30 min1 h
Delay Time
Brightness
Standby Time
Standby Dimming Level
Dual Sensor Tech. & RF Mode
Detection Range Microwave Sensor
Daylight Threshold
Scene prog.
DEFAULT
Subject to change without notice. Version1_20180621
Simple programming functions
Sensors 86370 and 86371 can be programmed remotely using a remote control without needing to set any fun-
ction in the sensor. This makes it easy to perform quick
changes in all functions.
The following pages describe the dierent procedures to
complete an installation.
Certain functions on the remote control have no function in this system, and cannot aect the end result of the
programming.
A dierence between 86370 and 86371 is that 86371 indi­cates with a ashing light source when a signal is received
from the remote control. This is due to installation at a high height. 86370 has an integrated red LED that indica­tes the same thing.
Programming with remote control 86368
On delivery, the sensor has a standard setting that is also very easy to use as start for the installation. The default
settings are:
Delay time: 5 min. Standby time: 5 min.
Standby dimming level: 10%
Daylight Threshold: Disabled
Sensor active: PIR and Microwave  Regardless of which settings are made, it is always easy to reset the presets using the DEFAULT button. On delivery the rotary switch on the sensor is set to 0 which gives the settings above. If the switch is changed to another position, that will be the standard setting.
Default setting of the sensor
9
Shift
ON OFF
AUTO MODE
DEFAULT
Start
LOW MID
Save
Apply
10% 50% 75%
POWER
100%
POWER
80%
100%
Disable
20 min
HIGH
MANUAL ON MODE
MANUAL SETTING
10 min1 min
Test
2 S
30 min15 min5 min30 s
1 min
20% 30% 50%10%
10 min
RX
STBY%
MW/PIR
RX
100%
MW+PIR
Send
PIR
Learn/
Erase
MW
5 min10 s30 min1 h
Delay Time
Brightness
Standby Time
Standby Dimming Level
Dual Sensor Tech. & RF Mode
Detection Range Microwave Sensor
Daylight Threshold
Scene prog.
Shift
ON
OFF
AUTO MODE
DEFAULT
Start
Save
Apply
POWER
100%
POWER
80%
MANUAL ON MODE
Brightness
Scene prog.
Shift
ON
OFF
AUTO MODE
DEFAULT
Start
Save
Apply
10% 50% 75%
POWER
100%
POWER
80%
100%
MANUAL ON MODE
Brightness
Detection Range Microwave Sensor
Scene prog.
Shift
ON
OFF
AUTO MODE
DEFAULT
Start
LOW MID
Save
Apply
10% 50% 75%
POWER
100%
POWER
80%
100%
Disable
HIGH
MANUAL ON MODE
MANUAL SETTING
Brightness
Detection Range Microwave Sensor
Daylight Threshold
Scene prog.
Shift
ON
OFF
AUTO MODE
DEFAULT
Start
LOW MID
Save
Apply
10% 50% 75%
POWER
100%
POWER
80%
100%
Disable
20 min
HIGH
MANUAL ON MODE
MANUAL SETTING
10 min1 min
Test
2 S
30 min15 min5 min30 s
Delay Time
Brightness
Detection Range Microwave Sensor
Daylight Threshold
Scene prog.
Shift
ON
OFF
AUTO MODE
DEFAULT
Start
LOW MID
Save
Apply
10% 50% 75%
POWER
100%
POWER
80%
100%
Disable
20 min
HIGH
MANUAL ON MODE
MANUAL SETTING
10 min1 min
Test
2 S
30 min15 min5 min30 s
1 min
10 min
5 min10
s3
0 mi
n1
h
Delay Time
Brightness
Standby Time
Detection Range Microwave Sensor
Daylight Threshold
Scene prog.
Shift
ON
OFF
AUTO MODE
DEFAULT
Start
LOW MID
Save
Apply
10% 50% 75%
POWER
100%
POWER
80%
100%
Disable
20 min
HIGH
MANUAL ON MODE
MANUAL SETTING
10 min1 min
Test
2 S
30 min15 min5 min30 s
1 min
20% 30% 50%10%
10 min
5 min10 s30 min1 h
Delay Time
Brightness
Standby Time
Standby Dimming Level
Detection Range Microwave Sensor
Daylight Threshold
Scene prog.
AUTO MODE
DEFAULT
Save
Apply
POWER
100%
POWER
80%
MANUAL ON MODE
Brightness
Scene prog.
DEFAULT
Apply
POWER
80%
Brightness
Subject to change without notice. Version1_20180621
It is possible to download all settings in the remote before
transmitting the package to a sensor. Go through the steps
as described below.
The settings that can be part of a package is:
Detection range (micro wave Sensor only)
Daylight Threshold
Delay time (after last movement detected) Standby Time (time at dimmed low level)
Standby dimming level (Low level before OFF)
Pre-set Scenes
Select Detection Range (If Microwave sensor is used).
Select Daylight Threshold or Disable the function
Select Delay Time (use Shift Button to alternate to BLUE
functions).
Select Standby Time (use Shift Button to alternate to Blue
functions).
Select Standby Dimming Level.
Memory for saving settings. And use Apply to sensing
information to sensor (The luminare will blink to conrm
the received information.).
Press Start.
Shift
ON
OFF
AUTO MODE
DEFAULT
POWER
100%
POWER
80%
MANUAL ON MODE
Shift
ON
OFF
AUTO MODE
DEFAULT
POWER
100%
POWER
80%
MANUAL ON MODE
10
Närvaro
Närvaro Frånvaro
100 %
0 %
Hålltid Standby tid
Standbydimningsnivå %
20 %
Subject to change without notice. Version1_20180621
Delay Time
Time after last presence detected. After time has elapsed, light will dim to Standby Dimming level.
Standby Time
How long light will remain on low level before turning o. The o function can be avoided by selecting +∞ (innity button).
Standby Dimming Level
How bright the light will be during the Standby Period. 10, 20, 30 or 50 % light level can be selected.
Daylight Threshold
If daylight is brighter than the set value, light will not turn
on when presence is detected.
Detection Range for Microwave Sensor
Depending on height and setting, the detection range can
be seen on pages 17–18. PIR sensor can be restricted by
covering part of the lens.
Programming of personal settings
11
Shift
ON OFF
AUTO MODE
DEFAULT
Start
LOW MID
Save
Apply
10% 50% 75%
POWER
100%
POWER
80%
100%
Disable
20 min
HIGH
MANUAL ON MODE
MANUAL SETTING
10 min1 min
Test
2 S
30 min15 min5 min30 s
1 min
20% 30% 50%10%
10 min
RX
STBY%
MW/PIR
RX
100%
MW+PIR
Send
PIR
Learn/
Erase
MW
5 min10 s30 min1 h
Delay Time
Brightness
Standby Time
Standby Dimming Level
Dual Sensor Tech. & RF Mode
Detection Range Microwave Sensor
Daylight Threshold
Scene prog.
AUTO MODE
DEFAULT
POWER
100%
POWER
80%
MANUAL ON MODE
Shift
ON
OFF
AUTO MODE
DEFAULT
Start
LOW MID
Save
Apply
10% 50% 75%
POWER
100%
POWER
80%
100%
Disable
20 min
HIGH
MANUAL ON MODE
MANUAL SETTING
10 min1 min
Test
2 S
30 min15 min5 min30 s
1 min
20% 30% 50%10%
10 min
5 min10 s30 min1 h
Delay Time
Brightness
Standby Time
Standby Dimming Level
Detection Range Microwave Sensor
Daylight Threshold
Scene prog.
Presence
PresenceAbsence
100 %
0 %
Hold Time Standby Time
Standby Dimming Level %
50 %
30 %
20 %
10 %
Subject to change without notice. Version1_20180621
Default and normal use will give full light output 100 % at presence. But it is possible to reduce power by 20 %.
This can be useful during a light xtures rst years of
use, where the light output can be more than the estima­ted value. Return to 100 % by pressing Power 100 % but­ton. This has to be made manually, no clock or calendar
function is used.
Standby Dimming Level is setting the light output during
Standby Time. This means that light can be set to a fun-
ctional level during absence, with enough light for the surrounding area. More light can be used close to exists,
stairwells, lifts etc.
Reduced power
Standby dimming level
12
Presence
Presence Absence
100 %
0 %
Hold Time
Hold Time: 30 s
1 min
5 min 10 min 30 min
StandbyTime
Standby Dimming Level %
Shift
ON OFF
AUTO MODE
DEFAULT
Start
LOW MID
Save
Apply
10% 50% 75%
POWER
100%
POWER
80%
100%
Disable
20 min
HIGH
MANUAL ON MODE
MANUAL SETTING
10 min1 min
Test
2 S
30 min15 min5 min30 s
1 min
20% 30% 50%10%
10 min
RX
STBY%
MW/PIR
RX
100%
MW+PIR
Send
PIR
Learn/ Erase
MW
5 min10 s30 min1 h
Delay Time
Brightness
Standby Time
Standby Dimming Level
Dual Sensor Tech. & RF Mode
Detection Range Microwave Sensor
Daylight Threshold
Scene prog.
Shift
ON
OFF
AUTO MODE
DEFAULT
Start
LOW MID
Save
Apply
10% 50% 75%
POWER
100%
POWER
80%
100%
Disable
20 min
HIGH
MANUAL ON MODE
MANUAL SETTING
10 min1 min
Test 2 S
30 min15 min5 min30 s
1 min
20% 30% 50%10%
10 min
RX
STBY%
MW/PIR
RX
100%
MW+PIR
Send
PIR
Learn/
Erase
MW
5 min10 s30 min1 h
Delay Time
Brightness
Standby Time
Standby Dimming Level
Dual Sensor Tech. & RF Mode
Detection Range Microwave Sensor
Daylight Threshold
Scene prog.
Shift
ON
OFF
AUTO MODE
DEFAULT
Start
LOW MID
Save
Apply
10% 50% 75%
POWER
100%
POWER
80%
100%
Disable
20 min
HIGH
MANUAL ON MODE
MANUAL SETTING
10 min1 min
Test
2 S
30 min15 min5 min30 s
Delay Time
Brightness
Detection Range Microwave Sensor
Daylight Threshold
Scene prog.
Närvaro
Närvaro Frånvaro
100 %
0 %
Hålltid Standby tid
Standbydimningsnivå %
20 %
Shift
ON
OFF
AUTO MODE
DEFAULT
Start
LOW MID
Save
Apply
10% 50% 75%
POWER
100%
POWER
80%
100%
Disable
20 min
HIGH
MANUAL ON MODE
MANUAL SETTING
10 min1 min
Test
2 S
30 min15 min5 min30 s
1 min
10 min
5 min10 s30 mi
n1
h
Delay Time
Brightness
Standby Time
Detection Range Microwave Sensor
Daylight Threshold
Scene prog.
Shift
ON
OFF
AUTO MODE
DEFAULT
POWER
100%
POWER
80%
MANUAL ON MODE
Shift
ON
OFF
AUTO MODE
DEFAULT
POWER
100%
POWER
80%
MANUAL ON MODE
Subject to change without notice. Version1_20180621
Delay Time sets the time period that light should remain on 100 % after last presence detection. Depen-
ding on the light source, and location, the time can be set to very short (LED’s) or longer for uorescent tubes. A longer time can be used to avoid rapid on/o sequences, which can be irritating. Select values in blue by pressing the Shift button rst. The TEST function is
explained later in this document.
Delay Time
Standby time sets the time for how long light should
remain ON at Standby Dimming Level. After Delay Time, light can go directly to OFF (0 s), 10 s, 1 min, 5min, 10 min, 30 min, or remain ON without turning OFF at all +∞ (in­nity button). Select values in blue by pressing the Shift button rst.
Standby time
13
Shift
ON OFF
AUTO MODE
DEFAULT
Start
LOW MID
Save
Apply
10% 50% 75%
POWER
100%
POWER
80%
100%
Disable
20 min
HIGH
MANUAL ON MODE
MANUAL SETTING
10 min1 min
Test
2 S
30 min15 min5 min30 s
1 min
20% 30% 50%10%
10 min
RX
STBY%
MW/PIR
RX
100%
MW+PIR
Send
PIR
Learn/
Erase
MW
5 min10 s30 min1 h
Delay Time
Brightness
Standby Time
Standby Dimming Level
Dual Sensor Tech. & RF Mode
Detection Range Microwave Sensor
Daylight Threshold
Scene prog.
Shift
ON OFF
AUTO MODE
DEFAULT
Start
LOW MID
Save
Apply
10% 50% 75%
POWER
100%
POWER
80%
100%
Disable
20 min
HIGH
MANUAL ON MODE
MANUAL SETTING
10 min1 min
Test
2 S
30 min15 min5 min30 s
1 min
20% 30% 50%10%
10 min
RX
STBY%
MW/PIR
RX
100%
MW+PIR
Send
PIR
Learn/
Erase
MW
5 min10 s30 min1 h
Delay Time
Brightness
Standby Time
Standby Dimming Level
Dual Sensor Tech. & RF Mode
Detection Range Microwave Sensor
Daylight Threshold
Scene prog.
Shift
ON OFF
AUTO MODE
DEFAULT
Start
LOW MID
Save
Apply
10% 50% 75%
POWER
100%
POWER
80%
100%
Disable
20 min
HIGH
MANUAL ON MODE
MANUAL SETTING
10 min1 min
Test
2 S
30 min15 min5 min30 s
1 min
20% 30% 50%10%
10 min
RX
STBY%
MW/PIR
RX
100%
MW+PIR
Send
PIR
Learn/
Erase
MW
5 min10 s30 min1 h
Delay Time
Brightness
Standby Time
Standby Dimming Level
Dual Sensor Tech. & RF Mode
Detection Range Microwave Sensor
Daylight Threshold
Scene prog.
ON
OFF
AUTO MODE
DEFAULT
MANUAL ON MODE
AUTO MODE
DEFAULT
MANUAL ON MODE
ON
OFF
AUTO MODE
DEFAULT
MANUAL ON MODE
Subject to change without notice. Version1_20180621
Press once, and light will remain ON until other action is taken. This will leave light constantly ON at 100 %. Pre­sence is muted. To leave this mode, press Auto Mode or DEFAULT button. Auto Mode will make the setting go back to previous programming. DEFAULT will return all set-
tings to default.
NOTE: A power failure will remove this function to previous setting (Auto Mode).
Press once more, and light will remain OFF until other action is taken. This will leave light constantly in OFF position. Presence is muted. To leave this mode, press Auto Mode or DEFAULT button. Auto Mode will make the setting go back to previous programming. DEFAULT will
return all settings to default.
NOTE: A power failure will remove this function to previous setting (Auto Mode)
Press this button once to leave any state of the ON/OFF function. This will return the sensor to previous settings.
Note: Manual on mode is disabled.
ON/OFF Function Constant ON
ON/OFF Function Constant OFF
Auto Mode
14
Shift
ON OFF
AUTO MODE
DEFAULT
Start
LOW MID
Save
Apply
10% 50% 75%
POWER
100%
POWER
80%
100%
Disable
20 min
HIGH
MANUAL ON MODE
MANUAL SETTING
10 min1 min
Test
2 S
30 min15 min5 min30 s
1 min
20% 30% 50%10%
10 min
RX
STBY%
MW/PIR
RX
100%
MW+PIR
Send
PIR
Learn/
Erase
MW
5 min10 s30 min1 h
Delay Time
Brightness
Standby Time
Standby Dimming Level
Dual Sensor Tech. & RF Mode
Detection Range Microwave Sensor
Daylight Threshold
Scene prog.
Shift
ON
OFF
AUTO MODE
DEFAULT
Start
LOW MID
Save
Apply
10% 50% 75%
POWER
100%
POWER
80%
100%
Disable
HIGH
MANUAL ON MODE
MANUAL SETTING
Brightness
Detection Range Microwave Sensor
Daylight Threshold
Scene prog.
Shift
ON
OFF
AUTO MODE
DEFAULT
POWER
100%
POWER
80%
MANUAL ON MODE
Subject to change without notice. Version1_20180621
A Lux Threshold will save energy when there is no need for articial light. The Lux sensor is reading through the xture cover when light is o. If the set value of lux is already full­led with daylight, the presence detection is muted, and light will remain o. The RF-signal will still be sent out to other sensor that might be under their individual Lux Threshold setting. This will make the system very exible.
The detection of presence can be muted if there is alreadysuf-
cient amount of daylight in the area. The settings are Manual, Low, Mid, High and Lux Disable.
Lux Threshold
This setting must be done on site at the actual moment when light should mute the sensor.
Manual Setting of Lux Threshold
With this level activated, the presence detection of the sensor will only work if the surrounding light level is more or less completely dark. Any light will mute the sensor.
Low Lux Threshold
With this level activated, the presence detection of the sensor will be muted during full eect of daylight. For a more
exact dusk or dawn setting, use the manual setting.
High Lux Threshold
If surrounding light is HIGHER than the threshold setting. Presence will not turn lights on.
If surrounding light is LOWER than the threshold setting. Presence will turn lights on.
With this level activated, the presence detection of the
sensor will be muted during daytime. For a more exact
dusk or dawn setting, use the manual setting
Medium Lux Threshold
Press the “eye” button (press Shift button rst). The sequence will start by turning the light o. During this pe­riod, the lux sensor will read and memorize the light level.
This will then be used as a threshold for when the sensor shall act or be muted when detecting presence. More light
then the set level; light will not turn ON. Less light, light
will turn ON.
Manual learning Sequence
This setting lets the sensor work without any eect of
surrounding daylight. The light will always turn on when presence is detected.
Lux Disable
15
Shift
ON OFF
AUTO MODE
DEFAULT
Start
LOW MID
Save
Apply
10% 50% 75%
POWER
100%
POWER
80%
100%
Disable
20 min
HIGH
MANUAL ON MODE
MANUAL SETTING
10 min1 min
Test
2 S
30 min15 min5 min30 s
1 min
20% 30% 50%10%
10 min
RX
STBY%
MW/PIR
RX
100%
MW+PIR
Send
PIR
Learn/
Erase
MW
5 min10 s30 min1 h
Delay Time
Brightness
Standby Time
Standby Dimming Level
Dual Sensor Tech. & RF Mode
Detection Range Microwave Sensor
Daylight Threshold
Scene prog.
Shift
ON OFF
AUTO MODE
DEFAULT
Start
LOW MID
Save
Apply
10% 50% 75%
POWER
100%
POWER
80%
100%
Disable
20 min
HIGH
MANUAL ON MODE
MANUAL SETTING
10 min1 min
Test
2 S
30 min15 min5 min30 s
1 min
20% 30% 50%10%
10 min
RX
STBY%
MW/PIR
RX
100%
MW+PIR
Send
PIR
Learn/
Erase
MW
5 min10 s30 min1 h
Delay Time
Brightness
Standby Time
Standby Dimming Level
Dual Sensor Tech. & RF Mode
Detection Range Microwave Sensor
Daylight Threshold
Scene prog.
Subject to change without notice. Version1_20180621
Shift
ON
OFF
AUTO MODE
DEFAULT
POWER
100%
POWER
80%
MANUAL ON MODE
AUTO MODE
DEFAULT
MANUAL ON MODE
Shift
ON
OFF
AUTO MODE
DEFAULT
Start
LOW MID
Save
Apply
10% 50% 75%
POWER
100%
POWER
80%
100%
Disable
20 min
HIGH
MANUAL ON MODE
MANUAL SETTING
10 min1 min
Test
2 S
30 min15 min5 min
30 s
Delay Time
Brightness
Detection Range Microwave Sensor
Daylight Threshold
Scene prog.
The Shift Button will activate all functions in blue. When the shift function is active, the selected value can be sent directly to a sensor, or part of the Save/Apply procedure. The Shift function is active for 20 seconds after last se­lected value is pressed. The the remote will return back to
normal status.
You can prevent the sensor switching on automatically in the event of movement, so called manual switch-on (the sensor will switch o as normal), which is common in classrooms. This requires that you have an impulse push­button installed on the sensor, see the wiring diagram.
Press Manual On Mode to activate the function. An impulse pushbutton also gives the option to manually adjust the light level temporarily.
The TEST function is used for checking the sensors detec­tion range. All other functions are temporarily muted. Light will dim down after 2 s. of absence, and go to 100% when presence is detected. For return to normal mode, select Auto Mode button or Default button.
Shi button
Manual switch-on
Test function
Shift
ON OFF
AUTO MODE
DEFAULT
Start
LOW MID
Save
Apply
10% 50% 75%
POWER
100%
POWER
80%
100%
Disable
20 min
HIGH
MANUAL ON MODE
MANUAL SETTING
10 min1 min
Test
2 S
30 min15 min5 min30 s
1 min
20% 30% 50%10%
10 min
RX
STBY%
MW/PIR
RX
100%
MW+PIR
Send
PIR
Learn/
Erase
MW
5 min10 s30 min1 h
Delay Time
Brightness
Standby Time
Standby Dimming Level
Dual Sensor Tech. & RF Mode
Detection Range Microwave Sensor
Daylight Threshold
Scene prog.
16
Shift
ON
OFF
AUTO MODE
DEFAULT
Start
LOW MID
Save
Apply
10% 50% 75%
POWER
100%
POWER
80%
100%
Disable
20 min
HIGH
MANUAL ON MODE
MANUAL SETTING
10 min1 min
Test
2 S
30 min15 min5 min30 s
1 min
20% 30% 50%10%
10 min
RX
STBY%
MW/PIR
RX
100%
MW+PIR
Send
PIR
Learn/
Erase
MW
5 min10 s30 min1 h
Delay Time
Brightness
Standby Time
Standby Dimming Level
Dual Sensor Tech. & RF Mode
Detection Range Microwave Sensor
Daylight Threshold
Scene prog.
DEFAULT
100%
Disable
MANUAL SETTING
Brightness
DEFAULT
Brightness
Light level
0
h 24 h
Normal electrical light
Daylight controlled light
Natural light
Stand-by time
Energy Saving Zone
Subject to change without notice. Version1_20180621
The integrated daylight sensor measures the incident light
and calculates how much electrical light is required for the desired lux level. The sensor communicates with the drive unit via DALI to provide the correct amount of light.
Daylight control
The sensor has an integrated lux sensor which can be used
to use less light when there is sucient incident daylight.
The setting should be made with as little daylight as pos-
sible. Using a lux meter is also useful for nding the right value. Remember that the lux sensor is located below the PIR lens and therefore measures a summarised value.
Adjust the light using the Brightness buttons to the desi­red level and the setting is saved. You can change this at any time. If you want to remove the function, press the Disable button (any lux threshold will also be removed).
17
Shift
ON
OFF
AUTO MODE
DEFAULT
Start
LOW MID
Save
Apply
10% 50% 75%
POWER
100%
POWER
80%
100%
Disable
20 min
HIGH
MANUAL ON MODE
MANUAL SETTING
10 min1 min
Test
2 S
30 min15 min5 min30 s
1 min
20% 30% 50%10%
10 min
RX
STBY%
MW/PIR
RX
100%
MW+PIR
Send
PIR
Learn/
Erase
MW
5 min10 s30 min1 h
Delay Time
Brightness
Standby Time
Standby Dimming Level
Dual Sensor Tech. & RF Mode
Detection Range Microwave Sensor
Daylight Threshold
Scene prog.
Shift
ON
OFF
AUTO MODE
DEFAULT
Start
LOW MID
Save
Apply
10% 50% 75%
POWER
100%
POWER
80%
100%
Disable
20 min
HIGH
MANUAL ON MODE
MANUAL SETTING
10 min1 min
Test
2 S
30 min15 min5 min30 s
1 min
20% 30% 50%10%
10 min
RX
STBY%
MW/PIR
RX
100%
MW+PIR
Send
PIR
Learn/
Erase
MW
5 min10 s30 min1 h
Delay Time
Brightness
Standby Time
Standby Dimming Level
Dual Sensor Tech. & RF Mode
Detection Range Microwave Sensor
Daylight Threshold
Scene prog.
Shift
ON
OFF
AUTO MODE
DEFAULT
POWER
100%
POWER
80%
MANUAL ON MODE
Subject to change without notice. Version1_20180621
The sensors can be used one at a time or in combination.
PIR+MW: The light is on when both of the sensors are activated PIR/MW: The light is on when PIR or MW is activated
PIR: Only PIR
MW: Only microwave. The range can be adjusted.
Press the Shift button rst, then select the sensor function that that will be in use. After a sensor is selected, it can take up 30 sec for it to “warm up” and operate normally.
The diagram shows the two sensors’ various detection
ranges at a ceiling height of 3 metres. 86370 will be used at a max. ceiling height of 6 metres. For a higher installation
height, use 86371.
Detection takes place in two dierent patterns via the PIR sensor’s two lenses. The PIR sensor cannot be set for larger detection areas, but it is possible to limit the range by covering part of the lens.
The microwave sensor works in a dierent way. The de-
tection range can be changed here by reducing the output
power. The output power can be set at 100%, 75%, 50% and 10%. At an installation height of 12 metres, the sensor will not work with the 10% setting. The dome-shaped
detection area will simply be too small.
Dual Sensor Technology
86370 Microwave and PIR sensor in combination (max 6 m)
Microwave sensor Ø 10 m
PIR sensor Ø 8 m
18
Subject to change without notice. Version1_20180621
The diagram shows the two sensors’ various detection
ranges at a ceiling height of 12 metres. 86371 is also supplied with a replaceable lens that is suitable for storage aisles and corridors with high ceilings. NOTE!
Only aects the PIR sensor’s detection. Rectangular lens is included in the packaging.
86371 Microwave and PIR sensor in combination (max 12 m)
Ø 16 m
H x D: 12 x 16 m (max)
12 m
16 m
MW: H x D: 12 x 16 m (max)
PIR: L x W x H: 16 x 6 x 12 m (max)
12 m
6 m
86371 with spherical lens
86371 with rectangular lens
19
L
N
LED Driver
Luminaire with DALI driver
L N Push SYNC SYNC
FIM14 FIM54
DA+ DA-
LED Driver
DA+ DA-
Luminaire with DALI driver
Max. 20 DALI loads
DA+ DA-
Subject to change without notice. Version1_20180621
Standalone with DALI Broadcast communication. 86370 or 86371 work as a standalone device that communicates with DALI.
Wiring example 1
One sensor
20
Subject to change without notice. Version1_20180621
L
N
Max. 20 DALI loads
L N Push SYNC SYNC
FIM14 FIM54
DA+ DA-
L N Push SYNC SYNC
FIM14 FIM54
DA+ DA-
LED Driver
DA+ DA-
Luminaire with DALI driver
LED Driver
DA+ DA-
Luminaire with DALI driver
Wiring example 2
86370 or 86371 with sync function connected between sensors for a larger detection range. In the ex-
ample, the DALI load is connected to a sensor but DALI loads can be connected to several sensors. A total
of 5 sensors can be synchronised.
Two sensors, where one is connected to the control system
21
Subject to change without notice. Version1_20180621
L
N
Max. 20 DALI loads
L N Push SYNC SYNC
FIM14 FIM54
DA+ DA-
L N Push SYNC SYNC
FIM14 FIM54
DA+ DA-
LED Driver
DA+ DA-
Luminaire with DALI driver
LED Driver
DA+ DA-
Luminaire with DALI driver
Wiring example 3
86370 or 86371 with sync function connected between sensors for a larger detection range. In the example, the DALI load is connected to a sensor but DALI loads can be connected to several sensors. A total of 5 sensors can be synch­ronised. A momentary pushbutton is connected to the sensors for manual dimming.
Two sensors, where one is connected to the control system and one manual pushbutton
22
Subject to change without notice. Version1_20180621
Technical specication
Product 86370 and 86371 Supply voltage 120 -227 VAC 50/60Hz DALI power supply 40 mA, max 20 loads Power consumption < 1 W Detection range 360° Detection area(DxH) 86370 12 m x 6 m (maximum) Detection area (DxH) 86371 16 m x 12 m (maximum) with spherical lens Detection area (DxWxH) 86371 16 m x 6 m x 12 m (maximum) with quadratic “corridor” lens
e-Sense Customised Stand-alone
Lorem ipsum
Fagerhult develops, manufactures and markets professional
lighting systems for public environments. Our operations are
run with a constant focus on design, function, flexibility and
energy saving solutions.
Fagerhult is part of the Fagerhult Group, one of Europe’s
leading lighting groups with operations in more than 15 dif-
ferent countries. AB Fagerhult is listed on the NASDAQ OMX
Nordic Exchange in Stockholm.
   Fagerhults Belysning AB SE-566 80 Habo, Sweden Tel +46 36 10 85 00 Fax +46 36 10 86 99 www.fagerhult.se
Loading...
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use