Factory Direct Hardware HDR110 SS User Manual

INSTALLATION MANUAL Clean Dry™

High Speed Concealed Hand Dryer

Warranty Registration and Inquiry For product warranty registration, TOTO U.S.A. Inc. recommends online Warranty Registration. Please visit our web site http://www.totousa.com. If you have questions regarding warranty policy or coverage, please contact TOTO U.S.A. Inc., Customer Service Department, 1155 Southern Road, Morrow, GA 30260 (888) 295 8134 or (678)466-1300 when calling from outside of U.S.A.

Important Safeguards

(For your safety, please follow the instructions below.)

In this Instruction Manual, the following symbols are shown for safe and proper use of the product and to alert you of the possibility of personal injury and damage to your property. The symbols and their meanings are as follows:

Warning

Caution

*Some models may have different components from the ones illustrated below.

Do not install the unit in the places where corrosive or combustible gas can be present.

Do not

disassemble

Do not use in

humid area

This may cause product failure or damage.

Never attempt to disassemble for repair or modification.

This may cause electric shock, fire, injury or failure

Do not install outdoors or where it is exposed to water.

This may cause current leakage, electric shock, fire, or failure.

Ignoring these symbols may cause personal injury and/or property damage.

Ignoring these symbols may cause severe injury and/or property damage.

Warning

It is necessary to install a circuit-breaker in the power supply

Important

Failure to do this may cause electric shock during overload or short circuit.

Caution

The chassis assembly must be installed on a smooth and even

Important

wall surface which has enough strength.

Failure to do this may cause damage or personal injury if it falls down.

Specification

Product HDR110#SS

Power Rating 120V AC, 4.25 Amps, 60 Hz, 510 W

Power Connection

Power Saving Function Automatically turns OFF after 60 seconds of use

Decibel Rating

Air Speed

Dry Time

Drain Tray Capacity

Ambient temperature 32° - 104°F (0° - 40°C)

Size

Weight

Hardwiring

58 dB

224 mph (100 meters/second)

12 seconds

0.27 gal (950 ml)

9-5/8" x 18-1/2" x 6-5/16"

22.2 lbs (10kg)

0GU3049E 2009.04

Before Installing

Set-up Drawing

Precautions

Confirm the rough-in, major dimensions and wiring diagram before installation in order to properly install the hand dryer and electrical wiring.

All electrical wiring should be installed in accordance with national/local codes and regulations with assistance from a certified electrician.

Mounting surface should be even and smooth.

Confirmation must be made that the wall has enough strength for hand dryer installation and be sure to use all the mounting hardware provided to securely install the hand dryer.

It is necessary to install circuit breaker for the power supply.

2. Others

Pay special attention so that both the top cover and the sensor surface are not flawed or scratched.

Do not place other devices using inverter or infrared sensor near the hand dryer, this may cause malfunction.

Some models may have different components as illustrated below.

3-9/16″ (90mm)

1-9/16″ (40mm)

2-3/4″ (70mm)

3-1/8″ (80mm)

2-3/8″ (60mm) 2-3/8″ (60mm)

FINISHED WALL

Junction box location

2″ (50mm)

1-3/16″ (30mm)

1-5/16″

(34mm)

5-1/8″

(130mm)

11-13/16″ (300mm)

26-5/16″ (668mm)

Recommended mounting bracket heights from floor are as follow:

- Male/Female: 29-1/2” (750 mm)

- Children: 23-1/2” (598 mm)

- Handicapped: 21-1/2” (547 mm)

Meets the American Disabilities Act Guidelines, ANSI A117.1 and CSA B651 requirements when mounted in a recessed wall where the front surface is not more than 4” (102mm) from finished wall and max. height of air blower outlet from finished floor is 47-1/4” (1200mm).

28-3/4″

(730mm)

12-5/8″

(320mm)

1-9/16″ (40mm)

6-7/16″

(164mm)

9-15/16″ (252mm)

2″ (50mm)

5-1/8″ (130mm)

OPEN WALL

26-5/16″ (668mm)

27-9/16″ - 27-5/8″ (700±2 mm)

FLOOR

+ 4 hidden pages