Factory Direct Hardware F4KIT User Manual

Apron Front

Applies to Model Numbers

Fireclay Sinks

• Saber or Keyhole Saw • Ruler & Pencil • Sanding Block • Sealant (not included) •

BF F3KIT, F4KIT, F5KIT

INSTALLATION INSTRUCTIONS

Tools Needed

• Sand Paper • Glasses • New Faucet (optional) •

TILE-IN INSTALLATION

1. This sink is designed for installation

flush with or slightly lower than the surrounding
tile.

2. Measure the sink apron and cabinet opening
to make sure sink apron will fit into cabinet
opening. If necessary, sand opening or add
wood filler strips.

3. Assemble faucet according to manufacturer’s
directions.

4. Placeathin layer of sealant at each corner of
the supporting frame where it will contact the
sink.

5. Gently position the sink within the frame,
placing the sink in the center of the cabinet.

* The cabinet and supporting
framework should be reinforced to
hold up t

o 300 lbs securely once
the sink is installed. Typically this
involvesatimber supporting frame
with 3/4” plywood deck orabrick
plynth.

UNDERCOUNTER INSTALLATION

1. The supporting frame should be positioned so that the top of the

sink rim (when placed inside the cabinet) is level and flush with
the top surface of the cabinet perimeter support or underlayment
at the cut out area.

2. Measure sink apron and cabinet opening to make sure sink
apron will fit into cabinet opening. If necessary, sand opening or
add wood filler strips.

3. Assemble faucet according to manufacturer’s directions.

4. Placeathin layer of sealant at each corner of the supporting

frame where it will contact the sink.

5. Gently position the sink within the frame, placing the sink in the
center of the cabinet.

6. Make sure the sink rim is level and flush with the cabinet
perimeter. Adjust or shim between the sink and the support if
needed to obtain proper fit. The top of the sink rim must be flush
with the top of the cabinet perimeter in order to obtain proper
contact with the underside of the counter top.

7. Assemble the strainer or garbage disposal to the sink according
to the manufacturers directions.

8. Using sealant between the sink and the cabinet is optional and
up to the buyers discretion.

Page1of 2

P 800.947.7000 www.worldimportsdesigns.com3/15/10

Apron Front

Applies to Model Numbers

Fireclay Sinks

BF F3KIT, F4KIT, F5KIT

SOLID SURFACE INSTALLATION

1. Follow steps 1-7 as outlined in the undercounter sink

installation section.

2. Carefully measure the counter top to determine the
exact location of the cut-out.

3. Measure the distance from finished wall to the center
of the sinks faucet holes. This dimension will be used
to locate the faucet hole centerline and back edge of
the cut-out on the counter top. Make sure the sink is
positioned to provide adequate clearance between
the faucet and the backsplash, finished wall, or
support frame. This will ensure full faucet operation
when installed.

4. From back edge of the counter top, locate the
dimension from the finished wall to the center of the
faucet holes and drawacenterline. Subtract 1 1/2”
from the faucet hole centerline to locate the back
edge of the cut-out. Trace the cut-out opening on the
counter top usingasoft lead pencil. Locate the
faucet holes.

5. Cut out the opening in the counter top, carefully
following the pencil line. Use an Orbital sander or
sanding block to smooth the edge of the cut-out area
and remove all saw marks. For laminate type counter
top, all exposed unlaminated surfaces near the
cut-out opening must be adequately finished and
sealed to prevent damage from water absorption.

6. Drill required faucet hole locations and install the
faucet according to the manufacturers directions.

7. Clean the top of the sink rim making sure the surface
is free from any debris. Clean the bottom of the
counter top around the cut-out area making sure the
surface is smooth and free of defects.

8. Applyagenerous bead of sealant around the sink rim
where the sink rim and the counter top meet.

9. Position the counter top over the sink, being careful
the sealant provides a complete seal between the
sink rim and the bottom of the counter top.
Immediately wipe away any excess sealant with a
damp cloth. Fill any voids between the rim and the
counter top with sealant.

10. Sealing the gap between the apron and the cabinet

is optional and up to the buyer’s discretion.

NOTE: The dimensions given for any fire

clay product is nominal. The material is a wet
clay fired in an oven, therefore, there is minimal
control over the finished size. The dimensions
given can vary +/-2%. Because of the dimen­sional variation possibility of fire clay products,
we recommend that the cabinetmaker wait until
the sink is on hand before making any cabinetry
counter top. There is no standard fitting frame­work or supporting brackets.

* These sinks can be installed flush with the
front of the cabinet or extend beyond the front
of the cabinet by approximately 1”.

* Due to the variety of installations possible with
these sinks, installation may require procedures
other than those described in these instruc­tions.

Page2of 2

P 800.947.7000 www.worldimportsdesigns.com3/15/10