Factory Direct Hardware 8875EO-RH User Manual

INSTALLATION INSTRUCTIONS:

1. Install threshold(s), if used, and fit and hang door(s).

2. Check that device handing matches door handing.

3. Tape full size RHR or LHR lock stile case and hinge

stile case templates to inside face of door (Figure 1).
Be sure center line of device is 39-13/16” from
finished floor. Prepare inside face of door for device
per templates.

4. Prepare lock stile of door for mortise lock (see
mortise lock instructions 941019).

5. Prepare outside face of lock stile for trim (see trim
instructions). Line X-X on trim instructions corresponds
to line X-X on device template.

6. Prepare trim for installation (see trim instructions).

7. Install mortise lock (Figure 2).

8. For 1-3/4” thick doors, cut 3/8” off device lift finger.

9. Attach device cases to door (Figure 3).

10. Push down lock stile lever and check for full retraction

of latch bolt. Release and check for full extension (3/4”).
Adjust lift finger if necessary (Figure 4).

11. Measure dimension “X” (Figure 3) and cut crossbar
tube to dimension “X.” Cut end without hole.

12. Install crossbar tube and wedge assembly (see
instructions 941009) and test crossbar for free action.

13. Prepare frame for strike (Figure 5).

14. Install strike to frame with two #12-12 x 12-24 x 1”

combination screws.

Figure 2. Install Mortise Lock

1. Remove retaining screws, scalp plate, and insert.

Scalp plate

Retaining

screws

Insert

2. For TP and K trims turn NL screw clockwise all the way in.

3. Loosen top and bottom faceplate screws, pivot faceplate to

4. Install mortise lock into door with two #12-12 x 12-24

LHR shown

RHR opposite

C device

L

39-13/16”

to finished

2-3/4”

2-3/4”

backset

Parallel to door edge

C

L

lock

stile

case

Parallel to door edge

C

L

hinge

stile

case

floor

Figure 1. Prepare Door

match door bevel, tighten top and bottom faceplate screws.

combination screws.

Faceplate
Faceplate

screw

NL screw

Bevel on

edge of

door

Faceplate

screw

#12-12 x 12-24 x 1” combination screws

Faceplate

Equal

}

angles

Sex bolts

880 trim

LHR shown

RHR opposite

Latch

bolt

Set

screw

To raise finger, tighten

set screw; to lower

finger, loosen set screw

Lift

finger

Figure 4. Adjust Lift Finger

5. Rotate latch bolt so flat side faces exit direction.

6. Replace insert, scalp plate, and scalp plate

retaining screws.

Flat side of

latch bolt

Exit direction

Top view

DESCRIPTION:

8875 and 8875-F MORTISE LOCK DEVICES

Mounting Fasteners

Surface #10-12 x 10-24 x 2”

880 trim #10-24 machine screws
Sex bolts #10-24 machine screws

“X”

Figure 3. Install Device

15/32”

3/8”

4-1/8”

4-7/8”

2-1/16”

5/8”

31/32”
R 1/16”

2-1/16”

1-13/32”

3/16”

5/8”

1-1/4”

1/2”

3/32”

1/2”

C mortise

L

Figure 5. Prepare Frame for Strike

DIRECTION NUMBER:

911179_00(12) 01-01-03

combination screws
(supplied with device)

911179-00

1-1/8”

“B”

C door and strike

L

575 and 575-2 strikes

LHR shown

RHR opposite

Door thickness

11/32”
C strike

L

C device

L

lock

2-7/16”

576A and 576B strikes

3/32”

3/4”

C strike

C device

L

2-7/16”

4-7/8”

L

SHEET#:

Strike

575

575-2

RHR opposite

3-3/8”

1-17/32”

C door and

L

strike

12/24” tap

2-1/16”

5/8”

1-1/4”

1 of 1Copyright © 2003 Ingersoll-Rand. All rights reserved.

Dim. “B”
1-25/32”

1-1/2”

LHR shown

1-13/16”

2 holes

4-1/8”

3-3/8”

3/8”

3/4”

DATE:

X

C device

L

11/16”

1-3/8”

Surface application (standard)

#25 drill and #10-24 tap, metal door;
pilot hole for #10 wood screw, wood door;
4 places

880 series trim or sex bolts

7/32” drill inside and
13/32” drill outside, metal door;
13/32” drill thru, wood door;
4 places

CUT HERE

2-3/4”

5/32”

6-3/4”

Mortise lock

and edge of door

C

L

3-5/8”

6-3/4”

CUT HERE

2-3/4”

X

C device

L

11/16”

1-3/8”

Surface application (standard)

#25 drill and #10-24 tap, metal door;
pilot hole for #10 wood screw, wood door;
4 places

880 series trim or sex bolts

7/32” drill inside and
13/32” drill outside, metal door;
13/32” drill thru, wood door;
4 places

Measure 2-3/4”

to hinge stile edge

CUT HERECUT HERE

CUT HERE

Hinge

stile

case

RHR LHR

C

L

Measure 2-3/4”

to hinge stile edge

of RHR door

of LHR door

9/16”

1-1/8”

2-1/4”

39-13/16”
to finished

floor

1/4” R

C device

L

1-1/4”

1-3/8”

1-1/2”

3-3/8”

C mortise lock

L

7-1/4”

L

L

Fold here for 1-3/4” RHR door;

for thicker door, cut on this line and

locate C of lock on C of edge of door

locate C of lock on C of edge of door

for thicker door, cut on this line and

Fold here for 1-3/4” LHR door;

1-3/8”

L

3-3/8”

L

1-1/2”

1-1/4”

C device

L

39-13/16”
to finished

floor

1/4” R

39-13/16”
to finished

floor

Surface application (standard)

#25 drill and #10-24 tap, metal door;
pilot hole for #10 wood screw, wood door;
4 places

C hinge stile case

L

C device

L

4-1/2”

3/8”

RHR

X

#16 drill and #12-24 tap for

metal door; pilot hole for #12

combination screw, wood

door; 2 places

Sex bolts

7/32” drill inside and
13/32” drill outside, metal door;
13/32” drill thru, wood door;
4 places

X

LHR