Factory Direct Hardware 52003-DS User Manual

72638

ASME A112.18.1 / CSA B125.1

Models 52001, 52002, 52003 & 52008 Series

Parts and Hardware included:

1 - Wall Slide Bar with adjustable ADA Slide Mechanism 1 - Full Spray Hand Shower with Rub Clean and Dual Check Valves 1 - 60” UltraFlex® Hose or 69” Double Spiral Hose 1 - Set of Mounting Hardware Six (6) #10 x 2-1/2” Wood Screws

WARNING

SLIDE BAR MAY NOT PROVIDE DESIGNED AMOUNT OF SUPPORT UNLESS THESE INSTALLATION INSTRUCTIONS ARE STRICTLY FOLLOWED.

For proper installation, both ends of Slide Bar MUST be installed into a wall stud. For solid support, at least two (2) of the three (3) screws on each end of the Slide Bar MUST go through the wallboard or tile and be tightly secured into the wall stud. Given standard stud sizes, only two (2) of the three (3) screws may screw into the wall stud.

Slide Bar may be installed vertically, horizontally or at an angle, so long as at least two (2) of the three (3) mounting screws on each end of the Slide Bar are secured into a wall stud. Locate the wall studs behind the wall before

beginning installation (a stud finder can be obtained from a hardware store).

WARNING

THE FOLLOWING STEPS REQUIRE DRILLING INTO THE WALL.

When drilling into the wall, exercise care to avoid any electrical wiring or plumbing that may be located behind the wall. Damaged electrical wiring can cause electrical shock and/or fire. Since older homes do not always fall in line with current housing codes and requirements, know where internal wall wiring is located so that no wires will interfere with your installation.

PROPER INSTALLATION IS EXTREMELY IMPORTANT. IF IN DOUBT, INSTALLATION SHOULD BE DONE BY A QUALIFIED PROFESSIONAL.

USING SLIDE BAR:

1. Read, understand and follow the information in the SAFETY WARNINGS

section of this instruction Sheet. Delta Faucet shall have no liability for any damage or injury caused by improper installation or use of this Slide Bar.

2. Grasp the Slide Bar when exiting or entering the bathtub or shower.

3. Use EXTREME caution on wet tub or floor surfaces.

4. DO NOT put entire weight on Slide Bar. Slide Bar is rated for persons weighing up to 300 pounds when properly installed.

5. DO NOT stand, sit or step on Slide Bar. DO NOT use Slide Bar as a step or platform to reach area above the tub. Use the bar for assistance ONLY.

CARE AND MAINTENANCE:

1. Use of mild soap and water or a non-abrasive cleaner is recommended

for cleaning.

2. Periodically inspect the Slide Bar for damage or looseness. DO NOT use if any damage or looseness exists. Contact your authorized dealer for assistance.

3. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.

INSTALLATION INSTRUCTIONS FOR ADA WALL SLIDE BAR & HAND SHOWER SYSTEM

Tools Needed for Installation:

•

Slot-headed screwdriver

•

Electric drill

•

5/32” drill bit

•

Soft cloth

•

Wrench or pliers

BEFORE INSTALLING SLIDE BAR:

1. Remove the Slide Bar and parts from the package. If concealed mount

Slide Bar is used, move cover plates away from mounting holes.

2. Determine where you want to install Slide Bar.

3. Place Slide Bar on wall at desired position. If mounting horizontally or vertically,

check that the Slide Bar is level.

With a pencil, mark the centers of the mounting hole positions on one end.

These are the points where you will later drill pilot holes for putting in the screws.

5. Repeat Step 4 for the other end of the Slide Bar. TO INSTALL INTO WOOD WALL STUDS:

6. Put on safety glasses before starting.

7. Use the 3/8” power drill and 5/32” drill bit to drill all holes into the wall and wood

wall studs at the marked positions. NOTE: If installing Slide Bar over ceramic tiles, the 1/4” carbide tip drill bit will be needed for drilling through the tile, in order to prevent damage to the tiles. Drill pilot holes through the tiles by using a 1/4” carbide tip drill bit. Once a hole has been drilled through the ceramic tiles, use the 5/32” drill bit to drill a pilot hole in the wood wall stud itself.

8. Place Slide Bar on wall, aligning mounting holes with the holes in the wall.

9. Insert the wood screws provided into one end of the Slide Bar. Screw into wall and wall stud (HAND TIGHTEN ONLY).

10. Repeat Step 4 for opposite end of the Slide Bar.

11.

Securely

tighten all mounting wood screws with a screwdriver.

12. If concealed mount Slide Bar is used, move cover plates over mounting holes and firmly press against the wall.

Exposed Mount Slide Bar

Mounting

Holes

Wood Wall Stud

Wallboard

Slide

Bar

Top View

Horizontal Mount

Concealed Mount Slide Bar

Mounting

Cover Plate

Wood Wall Stud

Top Wood Screw

Cover

Plate

Top Wood Screw

Bottom

Wood Screw

Located Below

In Wall Stud

Holes

Wood Wall

Stud

Wood Screw

Slide

Bar

Wallboard

Side View

Vertical Mount

Prior to snapping the

two cover flanges in place, make certain the Wall Slide Bar is installed securely. Then snap the two cover flanges into place, pressing tightly so the three catches on each wall flange lock into position.

www.deltafaucet.com

72638 Rev A.indd 4 11/15/11 4:33 PM

Install Mount/Slide Bracket. Reference Mount/Slide Bracket instruction installation (separate Sheet).

For installation with an existing shower head, remove the shower

head by turning counter-clockwise with adjustable wrench or pliers. Be careful not to unscrew the shower arm - hold the shower arm secure while unscrewing the shower head. Note: If the existing shower arm has an integral ball connector, replace it with a standard, 1/2” threaded shower arm.

10/20/11 Rev. A

Wrap the shower arm threads with plumber tape before installing into plumbing fitting. Hand tighten hose end to shower arm (or water supply) by turning clockwise. Then fully tighten with an adjustable wrench or pliers. Use a soft cloth between the jaws of the tool and hose connector to protect the finish.

Carefully tighten other end of hose to the hand shower. Place the hose from the hand shower into the holder (or bracket) section of the arm mount and slip down. Do not force. The hose takes a “natural drape” after warm water has been run through it.

The arm mount unit (for the hand shower) of the Wall

A. B.

Slide Bar can be adjusted (7A) by pushing up or down on the extended Paddle to move the unit up or down (on vertical or angled Slide Bar installations) and left or right (on horizontal installation). After positioning as desired, flip the Paddle into the straight (locked in) position. In addition, (7B) the arm mount can be adjusted by lightly tapping on the base of the arm mount unit.

9. 10.

Additional adjustments of the arm mount unit is available with the holder section of the arm mount unit. This holder can be turned clockwise or counter-clockwise for desired mounting of the hand shower.

Note: This “water saver” shower is designed to limit water usage to 2.5 gallons per minute maximum. A flow control disc is pre-installed in the end of the handle where the handle attaches to the hose. The hand shower also contains dual check valves for back-flow protection.

The arm mount unit also can be twisted clockwise or counterclockwise for desired positioning for the hand shower.

Do not force the handle in or out of the arm mount unit. The hand shower is easily removed from the arm mount by lifting the handle upward.

Cleaning Instructions

To clean the hand shower face plate: Remove the shower handle from

the hose. Soak the hand shower in a 50/50 solution of white vinegar

To clean the Wall Slide Bar or Arm Mount Unit: Wipe with soft, damp

cloth - do not use detergent or cleansers that may be harmful to the finish. and water for 30 minutes to dissolve mineral buildup. Reassemble; do not overtighten the handle to the hose. Turn on the shower to wash the impurities out of the hand shower.

LIFETIME FAUCET AND FINISH LIMITED WARRANTY

All parts and finishes of the Delta® faucet are warranted to the original consumer purchaser to be free from defects in material & workmanship for as long as the original consumer purchaser owns their home. Delta Faucet Company recommends using a professional plumber for all installation & repair.

Delta will replace, FREE OF CHARGE, during the warranty period, any part or finish that proves defective in material and/or workmanship under normal installation, use & service. Replacement parts may be obtained by calling 1-800-345-DELTA (in the U.S. and Canada) or by writing to:

In the United States: In Canada: Delta Faucet Company Masco Canada Limited, Plumbing Group Product Service 350 South Edgeware Road, 55 E. 111th Street St. Thomas, Ontario, Canada N5P 4L1 Indianapolis, IN 46280

This warranty is extensive in that it covers replacement of all defective parts and even finish, but these are the only two things that are covered. LABOR CHARGES AND/OR DAMAGE INCURRED IN INSTALLATION, REPAIR, OR REPLACEMENT AS WELL AS ANY OTHER KIND OF LOSS OR

72638 Rev A.indd 5 11/15/11 4:33 PM

DAMAGES ARE EXCLUDED. Proof of purchase (original sales receipt) from the original consumer purchaser must be made available to Delta for all warranty claims. THIS IS THE EXCLUSIVE WARRANTY BY DELTA FAUCET COMPANY, WHICH DOES NOT MAKE ANY OTHER WARRANTY OF ANY KIND, INCLUDING THE IMPLIED WARRANTY OF MERCHANTABILITY.

This warranty excludes all industrial, commercial & business usage, whose purchasers are hereby extended a five year limited warranty from the date of purchase, with all other terms of this warranty applying except the duration of the warranty. This warranty is applicable to Delta® faucets manufactured after January 1, 1995.

Some states/provinces do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. Any damage to this faucet as a result of misuse, abuse, or neglect, or any use of other than genuine Delta® replacement parts WILL VOID THE WARRANTY.

This warranty gives you specific legal rights, and you may also have other rights which vary from state/province to state/province. It applies only for Delta® faucets installed in the United States of America, Canada, and Mexico.

72638 Rev. A