Installation Instructions / Warranty
Interaktiv and Retroaktiv
Centerset Lavatory Faucets
Widespread Lavatory Faucets
Retroaktiv 4”Centerset Lavatory Faucets
06039XXX Tango with Cross Handles
06038XXX Tango with Scroll Handles
06037XXX Tango with Lever Handles
06103XXX Limbo with Cross Handles
06102XXX Limbo with Scroll Handles
06101XXX Limbo with Lever Handles
06302XXX Proaktiv Limbo*
06316XXX Proaktiv Tango*
Interaktiv 4” or 8” Widespread Lavatory Faucet
06633XXX Solaris
06577XXX Stratos
06653XXX Metro
06874XXX Interaktiv S
06633XX5 Aquos
06870XXX Proaktiv*
Retroaktiv 8” Widespread Lavatory Faucet
06122XXX Swing with Cross Handles
06118XXX Swing with Scroll Handles
06117XXX Swing with Lever Handles
06042XXX Tango with Cross handles
06041XXX Tango with Scroll Handles
06040XXX Tango with Lever Handles
06106XXX Limbo with Cross Handles
06105XXX Limbo with Scroll Handles
06104XXX Limbo with Lever Handles
06306XXX Proaktiv Limbo*
06317XXX Proaktiv Tango*
06320XXX Proaktiv Swing*
Retroaktiv 8” widespread faucets cannot be used in a 4” installation
*Requires Proaktiv handle set -- sold separately
Product Specifications
Recommended incoming water pressure 22 - 72 PSI
Recommended incoming hot water temperature 120o - 140oF*
Hole size in mounting surface
Valves 1 1/4”
spout 1 3/8”
Maximum mounting surface thickness 1 1/2”
Flow rate 2.2 gpm max.
This faucet requires 1/2” hot and cold supply lines (not included).
*some municipalities have codes limiting the maximum temperature of the water heater to 120oF or less. Please know and
follow all applicable local codes when setting the temperature on the water heater.
2
Limbo centerset Tango centerset
Limbo widespread Tango widespread
Swing widespread Solaris widespread
Aquos widespread
3
Install the hot and cold valves
Install the mounting nut, metal washer and
the fiber washer to the valve.
Install the o-rings to the grooves on the
mounting plates.
Insert the valve through the hole in the deck
from the below the mounting surface. The
hot valve is marked with a red dot.
From the top, install the stop ring to the
valve. Thread the mounting plate onto the
valve as far as it will go — the stop ring will stop it at the proper height. Place the
valve on the mounting surface. Turn the valves so that the outlet ports point toward
the center.
From below the mounting surface, tighten the mounting nut. Tighten the tensioning
screws.
Install the spout
Swing and Limbo Widespread:
Position the spout deco ring on the mounting
surface. Place the spout in the deco ring.
Interaktiv and Tango Widespread
Place the spout and sealing ring on top of
the mounting surface
4” Centerset models only: Position
the escutcheon on the countertop. Place the
spout on the escutcheon.
All models: From beneath the mounting
surface, install the mounting flange. Thread
the collar onto the stud and tighten.
4
.
:
Install the connecting hoses
Push a compression nut and ferrule over the
end of the connecting hose.
Push the end of the hose into the outlet port
on the valve.
Tighten the compression nut wrench tight.
Do not allow the connecting hose to twist, or
it will become loosened from the spout.
Repeat with the second connection hose.
Install the handles
Retroaktiv widespread
only: Install the deco rings on
the handles.
All models: Hold the lever
or cross part of the handle in the desired
“off” position with one hand. With the
other hand, turn the bell part of the handle
clockwise, so that it threads down over the
valve stem.
Install the pull rod
The Retroaktiv Tango and Limbo pull rods are
straight.
The Interaktiv and Retroaktiv Swing pull rods
are curved. These rods should be installed
with the curve as shown in the diagram.
Install the pop up drain.
Install the supply lines (not included).
Turn on the water and check for leaks.
5
Install the Pop Up Drain
Remove the plunger assembly.
Unscrew the drain outlet flange
from the tee.
Unscrew the tailpiece from the
tee. Wrap the threads with
plumbers’ thread tape and
replace.
Install the flexible sealing gasket
to the flange. Sit it in the sink
outlet.
plunger
flange
sealing gasket
mack gasket
link
From under the sink, install the
black mack gasket, white friction
friction ring
spring clip
ring, and retainer nut to the
flange. Do not tighten the nut
against the bottom of the sink at
retainer nut
nut
this time.
horizontal rod
Thread the tee and tailpiece to
the flange. The pivot must face
the faucet. If necessary, turn the
drain assembly.
pivot
tee
pivot ball
pivot ball seals
Tighten the retainer nut.
Sit the plunger assembly in the
tailpiece
drain.
Install the horizontal rod through the pivot ball seals and into the tee so that the
end goes through the loop in the bottom of the height adjuster. The two pivot ball
seals should surround the pivot ball.
Slide the link over end of pull rod. Tighten screw.
Slide one end of spring clip over end of horizontal rod. Slide link over end of
horizontal rod. Test motion of drain plunger. Reposition link as necessary. There
are multiple holes in the linkage -- the horizontal rod may go through any of the
holes.
When satisfied with the action of the drain, slide the other end of the spring clip
over the end of the horizontal rod.
6
Replacement Parts
Interaktiv
8
4
7
6
9
1
2
5
3
10 11
12
13
1 spout 88507XXX
2 aerator 13085XXX
3 valve 88503XXX
4 hot cartridge 94009000
5 cold cartridge 94008000
6 valve mounting set 88511000
7 spout mounting set 88508000
8 pull rod 88541XXX
9 connecting hose 88596XXX
10 Solaris handle set 06850XXX
11 Stratos handle set 06852XXX
12 Metro handle set 06853XXX
13 Interaktiv S handle set 06957XXX
7
Retroaktiv Swing
8
4
6
7
9
15 16
2
14
5
3
2 aerator 13085XXX
3 valve 88503XXX
4 hot cartridge 94009000
5 cold cartridge 94008000
6 valve mounting set 88511000
7 spout mounting set 88508000
8 pull rod 88541XXX
9 connecting hose 88596XXX
14 handle deco ring 88600XXX
15 cross handle set 06326XXX
16 scroll handle set 06325XXX
17 lever handle set 06324XXX
XXX = color
000 = chrome
17
8
620 = oil rub bronze
830 = polished nickel
820 = brushed nickel
930 = polished brass
Retroaktiv Tango
8
18
5
3
4
9
7
6
8
14
5
3
4
6
7
9
15 16
17
3 valve 88503XXX
4 hot cartridge 94009000
5 cold cartridge 94008000
6 valve mounting set 88511000
7 spout mounting set 88508000
8 pull rod 88541XXX
9 connecting hose 88596XXX
14 handle deco ring 88600XXX
15 cross handle set 06326XXX
16 scroll handle set 06325XXX
17 lever handle set 06324XXX
18 centerset escutcheon 88510XXX
9
Retroaktiv Limbo
18
5
5
4
6
7
9
20 21
22
3
3 valve 88503XXX
4 hot cartridge 94009000
5 cold cartridge 94008000
6 valve mounting set 88511000
7 spout mounting set 88508000
9 connecting hose 88596XXX
14 handle deco ring 88600XXX
18 centerset escutcheon 88510XXX
20 cross handle set 06305XXX
21 scroll handle set 06304XXX
22 lever handle set 06303XXX
14
4
9
6
7
3
10
Cleaning Recommendation for Hansgrohe Products
Modern faucetry and shower products utilize a combination of materials to comply with the needs of the
market with regard to design and functionality.
To avoid damage, it is necessary to use some caution when cleaning. Damage caused by improper
treatment is not covered under the Hansgrohe warranty.
Cleaning Materials for Faucets and Showers
• To remove lime scale, use only products made specifically for that purpose. Always follow the
manufacturer’s instructions when using.
• Do not use cleaners that contain hydrochloric, formic, acetic, or phosphoric acids, as these will
cause considerable damage to finishes and to plastic components.
• Never mix cleaning materials.
• Never use cleaners containing abrasives. Do not use abrasive cleaning cloths, pads, or sponges.
Cleaning Procedures
• Clean your faucets and shower products as and when required. Regular cleaning will prevent scale
buildup and water spotting.
• Follow the label instructions. Do not allow any cleaner to remain on the product for longer than
necessary.
• When using spray cleaners, spray first onto a sponge or cloth – do not spray directly onto the
product.
• After cleaning, rinse thoroughly with clear water to remove any cleaner residue.
Important
• Soap and shampoo residue can also cause damage to the product. Rinse well with clean water
after use.
• If the surface is already damaged, harsh cleaning materials will cause further damage.
Limited Lifetime Consumer Warranty
This product has been manufactured and tested to the highest quality standards by Hansgrohe, Inc. (“Hansgrohe”). This
warranty is limited to Hansgrohe products which are purchased by a consumer in the United States after March 1, 1996,
and installed in either the United States or Canada.
WHO IS COVERED BY THE WARRANTY
This warranty extends to the original consumer purchaser only.
WHAT IS COVERED BY THE WARRANTY
This warranty covers only your Hansgrohe manufactured product. Hansgrohe warrants this product against defects in
material or workmanship as follows: Hansgrohe will repair at no charge for parts only or, at its option, replace any product
or part of the product which proves defective because of improper workmanship and/or material, under normal installation,
use, service and maintenance. If Hansgrohe is unable to provide a replacement and repair is not practical or cannot be
timely made, Hansgrohe may elect to refund the purchase price in exchange for the return of the product.
LENGTH OF WARRANTY
Replacement or repaired parts of products will be covered for the term of this warranty as stated in the following two
sentences. If you are a consumer who purchased the product for use primarily for personal, family, or household purposes,
this warranty extends for as long as you own the product and the home in which the product is installed. If you purchased
the product for use primarily for any other purpose, including, without limitation, a commercial purpose, this warranty
extends only (i) for 1 year, with respect to Interaktiv and Retroaktiv products, and (ii) for 5 years, with respect to AXOR,
ShowerPower and Pharo products.
THIS WARRANTY DOES NOT COVER, AND HANSGROHE WILL NOT PAY FOR:
A. Conditions, malfunctions or damage not resulting from defects in material or workmanship.
B. Conditions, malfunctions or damage resulting from (1) improper installation, improper maintenance, misuse, abuse,
negligence, accident or alteration, or (2) the use of abrasive or caustic cleaning agents or “no rinse” cleaning
products, or the use of the product in any manner contrary to the product instructions.
11
C. Labor or other expenses for the disconnection or return of the product for warranty service, or for installation or
reinstallation of the product.
D. Accessories or related products not manufactured by Hansgrohe.
TO OBTAIN WARRANTY SERVICE
Contact your Hansgrohe retailer, or write to Technical Service at:
Hansgrohe Inc.
1492 Bluegrass Lakes Parkway
Alpharetta GA 30004
Or, call Hansgrohe toll-free at (800) 334-0455.
In requesting warranty service, you will need to provide
1. The sales receipt or other evidence of the date and place of purchase.
2. A description of the problem.
3. Delivery of the product or the defective part, postage prepaid and carefully packed and insured, to Hansgrohe Inc.
1492 Bluegrass Lakes Parkway, Alpharetta, Georgia 30004, Attention: Technical Service, if required by Hansgrohe.
When warranty service is completed, any repaired or replacement product or part will be returned to you postage prepaid.
EXCLUSIONS AND LIMITATIONS
REPAIR OR REPLACEMENT (OR, IN LIMITED CIRCUMSTANCES, REFUND OF THE PURCHASE PRICE) AS PROVIDED
UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE PURCHASER. HANSGROHE NEITHER ASSUMES
NOR AUTHORIZES ANY PERSON TO CREATE FOR IT ANY OBLIGATION OR LIABILITY IN CONNECTION WITH THIS
PRODUCT.
HANSGROHE SHALL NOT BE LIABLE TO PURCHASER OR ANY PERSON FOR ANY INCIDENTAL, SPECIAL, OR
CONSEQUENTIAL DAMAGES, ARISING OUT OF BREACH OF THIS WARRANTY OR ANY IMPLIED WARRANTY
(INCLUDING MERCHANTABILITY).
Some States do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or
exclusion may not apply to you.
This warranty gives you specific legal rights, and you may have other rights which vary from State to State.
You may be required by law to give us a reasonable opportunity to correct or cure any failure to comply before you can
bring any action in court against us under the Magnuson-Moss Warranty Act.
PRODUCT INSTRUCTIONS AND QUESTIONS
Upon purchase or prior to installation, please carefully inspect your Hansgrohe product for any damage or visible defect.
Prior to installing, always carefully study the enclosed instructions on the proper installation and the care and maintenance
of the product. If you have questions at any time about the use, installation, or performance of your Hansgrohe product, or
this warranty, please call or write to us at the toll-free number and address printed above.
Hansgrohe, Inc. • 1490 Bluegrass Lakes Parkway • Alpharetta, GA 30004
Tel. 770 360-9880 • Fax 770 360 9887
www.hansgrohe-USA.com
US - Installation Instructions • Part No. 90964501-03 • Revised 11/2006
Loading...