Factory Direct Hardware 04066LF User Manual [en, es, fr]
Installation Instructions / Warranty
Allegro E
06461XX0
Allegro E
04067XX0
Allegro E Gourmet
06460XX0
Allegro E Gourmet
04066XX0
Allegro E Kitchen & Prep Faucets
06461XX0 04067XX0
06460XX0
22
04066XX0
Technical
Données techniques Datos tecnicos
Information
Recommended
water pressure
Max. water pressure Pression d’eau maxi-
Recommended hot
water temp.
Pression d’eau
recommandée
mum
Température recommandée d'eau chaude
Presión recomendada en servicio
Presión en servicio
max.
Temperatura recomendada del agua
14.7 - 72.5 psi
147 psi
120� - 140� F*
caliente
Max. hot water
temp
Température maximum
d'eau chaude
Temperatura del
agua caliente max.
176�F*
Flow rate Capacité nominale Caudal máximo 2.2 gpm
Hole size in mounting surface
Dimension du trou dans
la surface de montage
Tamaño del orificio
en la superficie de
1 1/2"
montaje
Max. depth of
mounting surface
Profondeur maximale de
la surface de montage
Profundidad máxima
de la superficie de
2 3/8"
montaje
*Please know and follow all applicable local plumbing codes when setting the temperature on the water heater.
* Vous devez connaître et respecter tous les codes de plomberie locaux applicables pour le réglage de la température
du chauffe-eau.
*Debe conocer y cumplir todos los códigos locales aplicables para ajustar la temperatura del calentador de agua.
English – see page 4
Français – voir p. 7
Español – ver p. 10
3
English
Allegro E Kitchen & Prep Faucets
Installation Considerations
For best results, Hansgrohe recommends that this unit be installed by a licensed, profes-
•
sional plumber.
Please read over these instructions thoroughly before beginning installation. Make sure
•
that you have all tools and supplies needed to complete the installation.
Protection against backflow provided by check valve.
•
The supply hoses connect to the stops with 3/8" compression fittings (not included).
•
Installation
Remove the mounting nut, metal washer, fiber
washer and spacer from the faucet.
Place the faucet with sealing ring on the mounting
surface.
If the mounting surface is less than 1 3/8” thick,
install the gray plastic spacer. If the mounting
surface is greater than 1 3/8”, or if there is
insufficient space, omit the spacer.
Install the fiber washer, metal washer and
mounting nut.
Tighten the mounting nut and screws.
4
4
Install the handspray hose
Slide the nut, cone washer, brass washer and black
rubber washer over the end of the connecting hose.
Hold the handspray hose steady while tightening the
nut. Finish tightening the nut with a wrench.
Do not allow either hose to twist.
Twisting the supply hose may cause
it to loosen from the faucet, which
may cause water damage.
Twisting the handspray hose may
cause reduced water flow to the
handspray.
Connect the supply hoses
Connect the supply hoses to the stops. Use two
wrenches, as shown in the diagram, to keep the supply hose from twisting.
Do not allow either hose to twist.
English
Twisting the supply hose may cause
it to loosen from the faucet, which
may cause water damage.
Install the hose weight
Proper positioning of the hose weight insures that
the hose will retract smoothly.
Install the hose weight on the handspray hose.
Pull the hose out and guide it back into position. If
it does not retract smoothly, or the sprayhead does
not stay in place when resting in the spout, reposi-
tion the weight.
Turn on the water and check all connections for
leaks.
5
5
Loading...