Factor PRESENTER ONE, PRESENTER TWO Operation Manual

Download

Page 1

Modulized Wireless Portable Amplifier System

ISO 9001:2008

GREEN PRODUCT

Operation manual

Page 2

-1-

PRESENTER ONE Operation Manual

Congratulations and thank you for purchasing this all-in-one portable sound system. To ensure a trouble-free operation, please read the manual thoroughly to fully understand its controls and functions.

PRESENTER ONE can be installed with up to 4 receiver modules, of which one can be transmitter module. The wireless receiver/transmitter module is UHF PLL synthesized type with 16 preset frequencies.

Configuration

PRESENTER ONE comes equipped with the following:

1. AC power cord.

2. 1~4 or no wireless receiver/transmitter/MP3 module(s).

3. 1~4 transmitters, either handheld or beltpack transmitter (except version with no module installed).

Optional accessories

1. Weather proof dust cover.

2. Tripod stand

3. Companion powered speaker (PRESENTER TWO)

4. Wired microphone.

Remark

Manufacturer reserves the rights to change the above combinations without prior notice.

THIS DEVICE COMPLIES WITH PART 74 OF THE FCC RULES. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment.

This device complies with RSS-310 of Industry Canada. Operation is subject to the condition that this device does not cause harmful interference.

This device complies with Part 15 of the FCC Rules and RSS-123 of Canada. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including interference that may cause undesired operation.

Page 3

ISO 9001 / ISO 14001 / OHSAS 18001

-2-

PRESENTER ONE Parts and functions

A,B,C&D. Receiver or MP3 module C can be Transmitter module

1. Mic volume control

2. Line-in volume control

3. Tape/DVD power+volume control

4. Tone voulme control (BASS)

5. Tone voulme control (TREBLE)

6. Master volume control

7. Mic input (Balanced/Unbalanced)

8. Line input/output (R/L)

9. Voice priority

10. Slave output

11. Battery status indicator

(normal: GREEN; low: RED)

12. Charging indicator

13. Fuse

14. 24~32V DC input

15. AC input

16. Power switch

17. Speaker out

1 2 3 4 5 6

7 8 9 10

12 13 14

15 16

Page 4

-3-

PRESENTER TWO Parts and functions

A,B. Receiver or MP3 module B can be Transmitter

1. Audio link input

2. Audio link output

3. Volume control

4. Speaker out (switched)

5. Speaker out (unswitched)

6. 24~32V DC input

7. Fuse

8. Power status indicator (RED)

9. Power status indicator (GREEN)

10. Charging indicator

11. AC input

12. Power switch

1 2 3

4 5 6 7

8 9

A B

Page 5

ISO 9001 / ISO 14001 / OHSAS 18001

-4-

Operating procedures

After unpacking the unit for the first time, please charge the unit for at least 6 hours before operation. This is absolutely necessary as the built-in rechargeable batteries might have been discharged naturally due to long shipment and storage time, even though it has been fully charged in the factory prior to shipment.

To operate this portable sound unit, switch on the main POWER switch. If the Battery low indicator also glows, it means the batteries are weak and please recharge them.

The main POWER switch does NOT switch on the other devices as each of them has individual Power/Volume control. To operate each of them, you must switch them on accordingly.

Operating the dynamic wired microphone

To use a cable microphone, simply plug it into the MIC IN socket. The mic socket accepts both phone and Cannon jack. Rotate the dedicated volume control knob and master volume control, amplified sound could be heard from the speaker when voice is spoken into the cable microphone.

Operating the wireless microphone system

To operate the wireless system, just switch on the power/volume control on the module panel and the matching transmitter. Please have the channel setting on both the transmitter and receiver module being the same before operation. Please as well make sure that master volume control is set to minimum level before turning the unit on, especially working on a wireless version! Set the Master volume control to the mid position. Rotate the volume control knob on receiver panel clockwise to the desired levels. When voice is spoken into the microphone, amplified sound should be heard over the built-in speaker.

Voice Priority (Ducking) operation

Voice Priority operation is only necessary when Cassette tape or CD is playing. When the Voice Priority switch is put to ON position, the ducking function will be activated. While the music is playing, a voice input from either a Wired or Wireless Microphone will temporary override and turn down the volume of the background music and voice could be heard clearly. Background music will return to its original setting when no audio input is entering the microphone for a certain time. However, if the microphone is not switch off, the reentering of music into the microphone will also activate the voice priority function. So, Voice priority is best operated using microphones with on/off switch.

Battery Charging

Internally, the PRESENTER ONE contains 2 pcs of 12V/5AH maintenance free lead acid battery, which has no memory effect. When the batteries are weak, the battery low indicator LED will stay RED. To charge the batteries, simply plug in the AC power supply, the charging process will start automatically. While charging, the charging indicator will flash RED. When batteries are fully charged, the charging indicator will stay GREEN.

Page 6

-5-

Wired Audio Link

The PRESENTER ONE could be operated as MASTER as well as SLAVE. This depends on the setting of Master/Slave selector switch. However, the Challenger Slave can only be operated as SLAVE.

In order to operate Audio Link, you must have a PRESENTER ONE unit that operates as a MASTER. Only one unit is allowed to act as MASTER and the other(s) MUST operate as SLAVE(s). A MASTER unit is capable of connecting up to about 20 SLAVE units.

For the MASTER unit, the MASTER/SLAVE selector switch must be set to MASTER mode. The Challenger SLAVE unit does not have this selector. If you have two units of PRESENTER ONE/TWO, you could use one as Master and the other PRESENTER ONE as slave. To do that, just put the MASTER/SLAVE selector switch of the second PRESENTER ONE to SLAVE mode. For the MASTER unit, Audio Link IN jack should NOT be connected. To operate Audio Link, connect the Output jack of the MASTER to the Audio Link IN jack of the 1st SLAVE unit. The Output jack of this SLAVE should be connected to the Input jack of the 2nd SLAVE unit. Similar connection shall continue as such for the following SLAVE units.

Volume Control for MASTER or SLAVE When used on the MASTER, it controls the MASTER as well as all the SLAVE units. When used on the SLAVE unit, it only controls that particular SLAVE unit volume. Maximum number of SLAVE units to be connected with a MASTER is about 20.

Remark

There should NOT be a connection between the last SLAVE unit output and the input of the MASTER unit.

Page 7

ISO 9001 / ISO 14001 / OHSAS 18001

-6-

Wireless Audio Link

Different from Wired Audio Link, with new SLAVE's capability of installation of receiver and transmitter modules it eliminates all cable connection and largely extends the number limit of SLAVEs.

Application: For crowds of 1000 to 2000, e.g. speeches or forums. Configuration: One Master + several SLAVEs (with receiver module built in)

Application: For crowds of over 3000, e.g. stadiums. Configuration: One Master + several SLAVEs (with receiver and transmitter module built in)

T: Transmitter R: Receiver Channel: 1,2,3,... T1 matches R1, T2 matches R2, T3 matches R3, T4...

Page 8

-7-

SDR-6216m receiver module

6 7

1. Channel indicator

2. Power switch/volume control

3. Channel Selector

4. Microphone battery weak indicator

5. Diversity A/B indicator

6. Channel Scanner

7. Squelch control

First turn on the Power of the main unit. Then turn on the individual power of the receiver module. Select a channel that corresponds to the transmitter. When transmitter is turned on, either A or B diversity indicator will flash to indicate that signal has been received.

CHANNEL scanning

It is the automatic scan function key. To perform the scan function, the transmitter must be switched off. Once the key is being pressed, the unit will do an auto scan and the next clean channel will be displayed. Change the transmitter channel setting to this setting for an interference- free operation.

SQUELCH (SQ) setting

When a channel is in use and undesired interference signal is received, turn the SQ in clockwise direction to make the receiver less sensitive and thus less susceptible to interference. If this still does not solve the problem, it means this frequency is not applicable at current position. Please switch over to the next channel.

Page 9

ISO 9001 / ISO 14001 / OHSAS 18001

-8-

RP-6016m transmitter module

5 6

1. Channel indicator

2. Antenna socket(TNC type)

3. Channel selectors: Press ▲(up)▼(down) to increase/decrease channel number. Please select a non-interfering frequency channel to those used in the receiver modules.

4. Power switch

5. Audio sensitivity: Clockwise to increase its sensitivity level and anticlockwise to reduce.

6. Output power setting: LOW (left) for Low output power and HI (right) for high output power. Low output power will reduce the RF transmission distance and High output power will extend the possible RF transmission distance. However, if the module is installed on batterypowered amplifiers, HIGH output power would reduce more operation time than LOW output power since it requires more power for longer RF transmission.

Page 10

-9-

Operating the CD player Parts and functions

2 3 4 5

6 7 8 9 10

1. LCD display

2. Play/pause

3. Stop

4. Rev-Skip-Cue

5. Eject

6. CD/USB selector

7. Repeat

8. Folder skip

9. Infrared receiving LED

10. USB input

11. Power/volume control

Keys

Functions

Panel

Remote

PLAY/PAUSE

When this key is pushed during CD stop, play will start after track search. When this key is pushed during CD is playing, it will be changed to pause. When this key is pushed during CD is pausing, it will be changed to play.

STOP

When CD is not stop, if this key is pushed then CD will stop.

FUNC

When press this key will change between CD and USB mode.

UP/CUE

In stop mode: Change the starting play track (file) during stop mode, cyclic to the first track, if it is in the last track. In program entry mode: Change to the next track(file) for program select . In play mode, pause mode, program play mode, random play mode: Single pressed, skip the playing track (file) to next track (file) for normal play/pause mode, to next program index track(file) for program play/pause mode, to next random track(file) for random play /pause mode. Continue pressed, fast forward during play/pause when pressed more than 0.7sec.

DONW/REV

In stop mode: Change the starting play track (file) during stop mode, cyclic to the last track, if it is in the first track. In program Entry mode: Change to the previous track (file) for program select. In play mode, pause mode, program play mode: Single pressed, skip the playing track (file) to precious track (file) for normal play/pause mode, to previous program index track (file) for program play/pause mode. Continue pressed, fast reverse during play/pause when pressed more than 0.7sec.

Page 11

ISO 9001 / ISO 14001 / OHSAS 18001

-10-

FOLDER-UP

In stop mode: Skip the starting play folder to next folder during stop mode, cyclic to the first folder if it is in the last folder. In program entry mode: Change the file for program select to next folder’s first file, cyclic to the first folder if it is in the last folder. In normal play mode: Skip the playing file to the next folder’s first file.

FOLDER-DOWN

In stop mode: Skip the starting play folder to previous folder during stop mode, cyclic to the last folder if it is in the first folder. In program entry mode:

Change the file for program select to previous folder’s first file, cyclic to

the last folder if it is in the first folder. In normal play mode: Skip the playing file to the previous folder’s first file.

REPEAT

In mp3 mode and in USB mode . If this key is pushed, PLAY mode is changed cyclically shown below.

PLAY ALL RANDOM→REPEAT TRACK→REPEAT

FOLDER→REPEAT ALL→RANDOM REPEAT→PLAY ALL

IN CD mode If this key is pushed, PLAY mode is changed cyclically shown below.

PLAY ALL RANDOM→REPEAT TRACK→REPEAT ALL→RANDOM

REPEAT→PLAY ALL.

EJECT

When this key is pushed, door is moved out.

PROG

Set to programming mode.

When programming mode, “stop” key is pushed then program is all

cleared.

MUTE

When this key is pushed during CD is playing, the set will mute the output. Pushing again can recovery the output.

POWER

Power SW of the set.

ESP

In CDDA mode, Press ”ESP” key, The ESP display lighted and the set

is in electronic anti-shock state. The electronic anti-shock time is about 40 seconds. Press “ESP” key again, cancel the ESP function.

ID3

When this key is pressed , the“ID3”in the LCD display will flash, and the

ID3 TAG is displayed pressing this key again will cancel the ID3 function

0~10

You can use these keys to select the track you want directly.

VOL.-

When this key is pushed, the volume will decrease by 1dB per step, the min. volume is 0dB.

VOL.+

When this key is pushed, the volume will increase by 1dB per step, the max. volume is 30dB.

Caution: This player does not accept 8-cm diameter CD. User is advised to have the USB 2.0 formatted in “FAT” or “FAT 32”. The built-in USB 2.0 player can not be able to read the MP3 files stored in your USB if it is not formatted by either “FAT” or “FAT-32”. To avoid damage to the USB, remember to detach it only after switching off the player.

Page 12

-11-

UHF handheld microphone（SQ-5016）

Parts and functions

2 3 4 5 6

7 8

1. Cartridge

2. Battery weak/power LED

3. Power switch

4. LCD

5. Battery compartment

6. Bottom cap

7. Locking button

8. Setting button

9. Up button

10. Charging port

11. Down button

Battery installation

Insert or replace the batteries according to the correct polarity after opening the compartment. Many batteries are known to have leakage problem of conductive and corrosive liquid. So please remove the batteries if they are not to be used for a long period.

Other settings

1. Channel setting

Use UP or DOWN button to go to the CHANNEL/ FREQUENCY page. The cursor will flash to allow changes to be made. Pressing UP or DOWN button will increase or decrease the channel number. The corresponding frequency will change accordingly. When a desired channel is selected, it will be automatically saved and stored in the memory.

2. Making changes to Battery selection

Use UP or DOWN button to go to the Battery selection page.

Page 13

ISO 9001 / ISO 14001 / OHSAS 18001

-12-

Press UP or DOWN button to move the cursor to either NiMH (rechargeable battery) or AKLN (Alkaline battery) position. When the desired battery has been selected, it will be automatically saved and stored in the memory. Remark: NiMH battery must be selected when rechargeable battery is being used. Never select AKLN (Alkaline) when microphone is intended for charging as Alkaline battery can not be charged ! Wrong selection of battery will result in battery sensing electronics to display wrong and misleading status information.

3. Making changes to Sensitivity Level

Use UP or DOWN button to go to the SENS SET page. Press UP or DOWN button to increase or decrease the Sensitivity Level of the microphone. The MAX level is 4 and the MIN level is 1.When a desired sensitivity level has been selected for your application, it will be automatically saved and stored in the Memory. Remark: When selecting Sensitivity level, please bear in mind that Level 1 is for close proximity singing purposes whereas Level 4 is for use of microphone on tripod mount for speech purposes. When Level 4 setting is used for close proximity singing, high SPL input will result in undesirable distortion in the output.

After performing setting changes, you could turn the protective cover 180° in either direction to block the buttons from being accidentally adjusted.

Page 14

-13-

UHF beltpack transmitter（SM-5016）

Parts and functions

1. Antenna

2. Battery weak/audio mute indicator

3. Audio mute switch

4. (Lavalier microphone) Mini XLR connector

5. LCD

6. Charging port

7. Cover release button

8. Power switch

9. Gain control (GT, high impedance)

10. Gain control (MT, low impedance)

11. SETTING button

12. UP button

13. DOWN button

14. Battery compartment

15. Charging contacts

Battery installation

Other settings (SM-5016)

1. Channel setting

15 15

Page 15

ISO 9001 / ISO 14001 / OHSAS 18001

-14-

2. Making changes to Battery selection

Use UP or DOWN button to go to the Battery selection page. Press UP or DOWN button to move the cursor to either NiMH (rechargeable battery) or AKLN (Alkaline battery) position. When the desired battery has been selected, it will be automatically saved and stored in the memory. Remark: NiMH battery must be selected when rechargeable battery is being used. Never select AKLN (Alkaline) when microphone is intended for charging as Alkaline battery cannot be charged! Wrong selection of battery will result in battery sensing electronics to display wrong and misleading status information.

Page 16

-15-

Maintenance-free Lead Acid battery

Guidelines for maintenance-free Batteries:

1. Battery should operate at temperatures between 15°C ~ 50°C. To ensure a longer life span, it should be kept between 5°C ~ 35°C. For optimum result, 20°C ~ 25°C will be ideal. When temperature falls 15 degrees below zero, battery will undergo some changes in its chemical contents and therefore cannot be recharged. Operating the battery at higher temperature will result in higher capacity but shorter lifespan, whereas lower temperatures operation has a longer lifespan but less capacity.

2. If the battery is not recharged 72 hrs after it is completely used, it will be permanently damaged.

3. When the battery is being charged, the internal gases will be electrolyzed into water at the negative charge, maintaining the battery’s storage abilities with no water added. However, erosion at the charged ends of the battery will cause poor performance.

4. The battery’s cycle lifespan (no. of charge and discharge cycle) is determined by the degree at which power is dissipated, especially the degree of discharged each time it is used and the recovery charging method. For normal use, the battery can be used for longer hours when less power is dissipated each time and vice versa. At 25°C, maintenance-free batteries could be charged 150 ~ 200 times at 100% discharge each time.

5. Decrease in capacity, internal short circuit, deformation in appearance, erosion of charged ends and decrease in open circuit voltage are symbols indicating battery is approaching the end of its life cycle.

6. When two batteries are used in parallel connection, the resistance of the cables should be kept equal.

Properties of the Lead Acid Battery:

1. Has no memory effect. Can be charged anytime, even when the recharge indication light is off.

2. Performance and efficiency are affected by changes in the environment, especially temperature and humidity. (Best operated between 20°C ~ 25°C)

3. Battery discharge naturally according to a certain pattern even not in use. For best performance and a prolonged lifespan, it should be recharged every month even when not in use.

4. Under normal circumstances, battery could last for about a year.

5. When the battery’s life expires, possible indicators include internal short-circuit, decrease in capacity, deformation in appearance, erosion of charged ends and decrease in operating voltage.

User’s Precautions:

1. For first-time use, charge the battery for 10 hrs until it is fully charged.

2. To maintain performance and lifespan, if product has not been used for 3 months after the initial shipment, please fully charge the battery.

3. Before each use, it’s advisable to charge the battery to its full capacity.

4. The average lifespan of the battery is one year. The user is advised to change the battery after one year of use.

5. The current consumption is in direct ratio with load current. The more current consumption, the

less the operation time.

12I2226