Facom E.506-340S, E.506-200S, E.506-135S User guide

Dear User,

Thank you for purchasing this digital torque-angle adaptor. This manual will help you to use the many features of your new digital torque-angle adaptor. Before operating the torque adaptor, please read this manual completely, and keep it nearby for future reference.

MAIN FEATURES

• Digital torque-angle value readout

• +/-2° ( rotating 90° at speed of 30°/sec) for angle accuracy

• +/- 3% or +/- 4% for torque accuracy

• CW and CCW operation

•

Buzzer and LED indicator for the 9 pre-settable target torques or angles

• Five Units Selectable (N.m, ft-lb, in.lb, kg.cm, degree)

• 50 data memory for recall and joint torque-angle auditing

• Auto Sleep after about 2 minutes idle

• Both AAA and rechargeable batteries are compatible

NAMES AND FUNCTIONS OF PARTS A

1. LED Indicator 7. Memory Number

2. Buzzer 8. Buttons

3. LCD Display 9. Communication Port

4. Torque/Angle Value 10. Extension bar

5. Units 11. Battery cover

6. Peak/Track Mode

SPECIFICATIONS

Torque Accuracy *1 CN / CW :±3% CCW :±4%

Angle Accuracy *2 +/- 2° ( rotating 90° at speed of 30°/sec)

Measured Angle Range

Data memory size 50

PC Connectivity *3 No

Pre-setting No 9 sets

Bright LED 12 LED / 2 Red+10 Green

Torque Operation Mode Peak Hold / Track

Unit selection N.m, ft-lb, in-lb, kg.cm, degree

Button 5

Battery AAA x 2

Battery Life *4 (Continuous operation) 24 hrs.

Battery Life *4 (Standby) 1 Year

Operating Temperature

Storage Temperature

Humidity Up to 90% non-condensing

Drop Test 1 m

Vibration Test *5 10 G

Life time *6 10000 cycle

Environmental test *7 Pass

Electromagnetic compatibility test *8 Pass

E.506-135S - E.506-200S - E.506-340S

1° ➞ 999.0°

-10°C ➜ 60°C

-20°C ➜ 70°C

Note: *1: The accuracy of the readout is guaranteed from 20% to 100% of maximum range +/- 1 increment. For maintaining accuracy, calibrate the adaptor at regular intervals (1 year recommended).

*2: The angle accuracy is guaranteed at ±2° when rotating adaptor

to 90° at speed of 30°/sec.

*3:

Use a special designed cable (accessory) to upload record data to PC.

*4:

Use two AAA batteries (Tested condition: Toshiba carbon-zinc battery) *5: Horizontal and vertical test. *6: One cycle means turning the torque adaptor from 0 N.m to

maximum torque and back to 0 N.m.

*7: Environmental test: a. Dry heat e. Impact (shock) b. Cold f. Vibration

c. Damp heat g. Drop

d. Change of temperature *8: Electromagnetic compatibility test: a. Electrostatic discharge immunity (ESD) b. Radiated susceptibility c. Radiated emission

BEFORE USING THE ADAPTOR

BATTERY INSTALLATION B

• Loosen the screw of the battery cover.

• Insert two AAA batteries matching the -/+ polarities of the battery to

the battery compartment.

•

Put on the battery cap and rotate it tightly according to the following ﬁ gures.

POWER ON AND AUTO ZERO RESET

• Let the adaptor be sat without touching it

• Gentlely press

to power on.

• Auto zero-reset will be processed ﬁ rst.

• The adaptor will be started in torque or angle mode.Which mode will be

started depends on in which mode the adaptor is powered-off last time.

• In torque mode, ﬁ rst is torque zero-reset and then a target torque screen

will show.

• In angle mode, it ﬁ rst do several seconds of angle- zero-reset and then a target angle screen will show.(Very important issue: See attention)

• If it takes too long in angle reset, press

Press

Torque zero reset

will perform reset again.

N.m

Current target torque

Current target angle

ATTENTION:

1. If

is appeared, refer to “ERROR MESSAGE”.

2. IMPORTANT! During angle reset, keep the adaptor still and never shake, vibrate or even

touching the adaptor.

If the adaptor is moving again and again, the zero reset will not stop.

Finally,

will be shown.( Refer to “ERROR MESSAGE”)

AUTO POWER OFF

The adaptor will auto power off after about 2 minutes idle for power saving.

CAUTIONS:

During communication period (

appears), the auto power-

off function is disabled.

• Press for zero reset.

• Usually press

to zero reset

Press

the digital torque-angle adaptor before using the adaptor. It will guarantee a better accuracy.

• In angle mode, please keep the adaptor steady without any disturbance

and press to do zero-reset.

• In torque mode, if an external force is applied to the torque adaptor

during zero-reset period, an initial torque offset error will occur.

HARDWARE RESET

• To do haraware reset, remove battery and re-install it.

• If the adaptor does not function normally or

appeares,

please go through the reset process to reset the adaptor.

ERROR MESSAGE

LOW VOLTAGE INDICATOR

If the battery voltage is too low, the adaptor will display a battery symbol and then turn off. Replace batteries.

Low battery indicator

When

shows during power-on process, it means this

adaptor has ever been applied more than 110% of torque of the

spec.The accuracy of torque may be lost.

In angle mode, if the adaptor does not reset successfully for a period of time,

will be shown. Press to do zero-reset

again. Notice that during resetting process, never vibrate or shake

the adaptor. Keep it rest.

shows that the adaptor does not work functionally,

please do hardware reset. Refer to “HARDWARE RESET”.

In angle mode, iff the adaptor rotates too fast, shown.Do press

to zero reset the adaptor.

will be

OPERATION

FAST GETTED START

➜ Press

➜ Target torque or angle will be shown.

➜

and then press

➜

➜ ➜ Start to rotate adaptor. ➜ Watch out the warning LED, sounds and LCD to stop rotation.

T-mode torque operation

➜ In T-mode, LCD displays the current torque value. ➜ After release force, the LCD value will return to O.

P-mode torque operation

➜ In P-mode, LCD displays the maximum torque value. ➜ After release force, the LCD shows the catched maximum value. (ﬂ ashing) ➜ Now press

Angle operation

➜ In angle mode, LCD displays the angle rotated after the reaching over 5% of

➜ Now press

1- INSTALL THE ADAPTOR AND POWER ON

● Press to power on the adaptor.

2- NO APPLING FORCES ON ADADAPTOR

to power on. No appling forces on adaptor.

Press

to select the torque unit or “ ° ” (angle mode)

to set target value

Or press

to select the pre-set target values

Press

to reset adaptor.(suggested)

to record maximum torque value, or press to clear it.

the rated maximum torque.

to record angle value, or press to clear it.

E.506-135S

E.506-200S

E.506-340S

www.facom.com

E.506-135S

903605

(N.m) (‘‘)

0,1 1/2

Instruction manual

E.506-200S

903613

Min. ➞ Max.

6,8➞135

10➞200

17➞340

E.506-340S

903621

(N.m) (mm)

NUen-E.506/0811

3- TARGET TORQUE OR ANGLE WILL BE SHOWN

N.m

Without

appling force

Target torque or angle

4- SET TARGET TORQUE OR ANGLE

●

Press to select the torque unit (torque mode) or ‘‘°’’ (angle mode).

● Then press or to set targuet value.

● Note that the target value will be saved automatically with the

current M number discarding torque or angle.

●

Another way is to press to select the pre-set target value (M1~ M9)

EX. Select units

N.m

in.lb

In.lb

ft.lb

Ft.lb

kg.cm

Kg.cm

° (angle)

● if is shown as press or .It indicates

that the key is locked.

Please refer to “Key Lock/Unlock” to un-lock keypad.

EX. Set targets

N.m

EX. Using the pre-set targets

N.m

5- ZERO-RESET ADAPTOR

● Press to zero-reset the adaptor. (suggested)

● Refer to ‘‘POWER ON AND AUTO ZERO RESET’’

and ‘‘ZERO RESET’’.

Press

TORQUE ONLY 6- CHEK P/T MODE OF TORQUE

●

Refer to ‘‘P/T MODE SELECTION’’ to set P or T-mode operation of torque.

Deﬁ nition T-mode torque view

1. In T-mode, if a force is applied on adaptor, LCD displays and tracks the current torque value.

2. After releasing force, the LCD value will return to target setting view.

P-mode torque view

N.m

1. In P-mode, LCD displays the maximum torque value.

2. After releasing force, the LCD shows the catched maximum value. (ﬂ ashing)

N.m

7- START TO ROTATE ADAPTOR

●

Rotate the adaptor clockwise or counter-clockwise

WATCH OUT THE WARNING LED, SOUNDS AND LCD TO STOP ROTATION

● There are 12 LEDs to indicate the current torque or angle reaching 80%,

85%, 90%, 95%, 97.5% and 99.5% of target torque/angle.

Red Green

99.5% 97.5% 95% 90% 85% 80%

Angle-mode

●

In angle-mode, after releasing force, the LCD shows the maximum angle and

the maximum torque (alternatively).

●

Pressing will clear the maximum angle and go back to show the target angle.

●

Pressing will record the maximum angle, then clear it and go back to show the target tangle.

Maximum angle

and torque

(alternatively)

11- BACK TO STEP 2 FOR NEXT OPERATION

● There is also a buzzer to indicate the reaching level of target value.

Interval sound means it reaches over 80% and long sound means it reaches over 99.5% of target value.

((..((..((..  ..))..))..))..))

(((((((((..  ..))))))))))

➜ over 80 %

➜ over 99.5 %

VISIT SETUP MENU

●

From the target torque/angle screen, long press to go into setup

menu. Continuously press

angle-operation menu,key lock menu, record menu, record clear-all menu, operation count menu and communication menu. Finally press

TORQUE / ANGLE VALUE WHEN ROTATES

skip out the setup menu and go back to the target torque/angle screen.

T-mode Torque value

● In T-mode, if a force is applied on adaptor, LCD displays and tracks the

current torque value.

● After releasing force, the LCD value will return to target setting view.

Apply 13.5 N.m

Release force

N.m

Current torque value

N.m

Current target

torque or angle

P-mode Torque value

● In P-mode, LCD displays the maximum torque value.

● After releasing force, the LCD shows the maximum value. (ﬂ ashing).

Apply 13.5 N.m

12.0 N.m 24.48 N.m

N.m

Release force

N.m

Angle value

●

In angle mode, LCD displays the angle rotated. The angle is counted after the

rotation torque has been reaching over 5% of the rated maximum torque.

● After releasing force, the LCD shows the maximum angle and the

maximum torque.(alternatively)

EX. For a 30.00 N.m adaptor, 5% is 1.5 N.m

No force Release force1.5 N.m

10- SAVE

TORQUE / ANGLE VALUE OR CLEAR MAXIMUM VALUE

P-mode

●

In P-mode, after releasing force, the LCD shows the maximum value. (ﬂ ashing).

●

Pressing will clear the maximum torque and go back to show the target torque.

●

Pressing will record the maximum torque, then clear it and go back to show the target torque.

N.m

Maximum torque

Show rec (record) and its number

Continuously

applying force

Maximum angle and torque

N.m

P/T MODE SELECTION

● Visit the P/T mode menu, press or to select the Peak-

hold or Track mode of torque operation.

● Continuously pressing will skip out the setup menu and go back

to the target torque/angle screen.

Target torque

N.m

Show rec (record) and its number

N.m

Target angle

can visit the P/T mode menu, torque-unit-in-

Long Press

P/T mode menu

Torque-unit-in-angle

operation menu

Key lock menu

Re-cord menu

Record clear-all menu

Operation count menu

Communication menu

again to

N.m

SELECT TORQUE UNIT IN ANGLE OPERATION

● Visit the torque-unit-in-angle-operation menu,

press or to select the torque unit during angle rotation.

● Continuously pressing will skip out the setup menu and go back

to the target torque/angle screen.

N.m

in.lb

ft.lb

kg.cm

KEY LOCK/UN-LOCK

● Visit the key lock menu, press or to select the key lock on

or off.

● Continuously pressing will skip out the setup menu and go back

to the target torque/angle screen.

Auto change

Lock on / off selection

VIEW DATA RECORD

● Visit the record menu, press or to select the data number

and view it.

● If no record exists, will be shown.

N.m

● Continuously pressing will skip out the setup menu and go back

to the target torque/angle screen.

Press or to select data

CLEAR A SINGLE RECORD

● Visit the record menu

● Press or to select the data number you want to delete.

● Press twice to delete the current data.

(

will be shown)

● If press once, will be shown. If you want to

abandon, just press to skip out this menu.

● Continuously pressing will skip out the setup menu and go back

to the target torque/angle screen.

Press or to select data

Press

Abandon

CLEAR ALL RECORDS

● Visit the record clean-all menu

●

Press twice to delete the all record data. ( will be shown)

● If press once, will be shown. If you want to

abandon, just press

to skip out this menu.

● Continuously pressing will skip out the setup menu and go back

to the current target angle screen.

Press

Abandon

VIEW OPERATION COUNTS

● Visit the operation counts, the operation counts will be shown.

● Operation counting record counts every time the adaptor has been

used over 60% of maximum torque.

This record is not erasable until re-calibration.

● The feature will count up to 65,000 measurements.

● The following ﬁ gure means the recorded count is 10025.

● Continuously pressing will skip out the setup menu and go back to

the target torque/angle screen.

EX. 10025 times

MAINTENANCE AND STORAGE

ATTENTION:

One-year periodic recalibration is necessary to maintain accuracy.

Please contact your local dealer for calibrations.

CAUTION:

1- Over-torquing (110% of Max. torque range) could cause breakage or lose of accuracy.

2- Do not shake violently or drop adaptor.

Do not expose this adaptor to dust or sand as this could cause serious damage.

Keep a spare battery on hand when going on a long trip or to cold areas.

Sweat, oil and water can prevent a battery’s terminal from making

Press

3- Do not leave this adaptor in any place exposed to excessive heat,

humidity, or direct sunlight. 4- Do not use this apparatus in water.(it is not waterproof) 5- If the adaptor gets wet, wipe it with a dry towel as soon as possible. The salt in seawater can be especially damaging.

6- Do not use organic solvents, such as alcohol or paint thinner when

cleaning the adaptor. 7- Keep this adaptor away from magnets. 8-

9- Do not apply excessive force to the LCD panel.

BATTERY MAINTENANCE

1- When the adaptor is not going to be used for an extended period of time, remove the batteries.

23- Do not mix battery types or combine used batteries with new ones. 4-

electrical contact. To avoid this, wipe both terminals before loading a battery.

5- Dispose of batteries in a designated disposal area.

Do not throw batteries into a ﬁ re.

Facom E.506-340S, E.506-200S, E.506-135S User guide

Specifications and Main Features

Frequently Asked Questions

User Manual