Faber Pro Magnum User Manual
Pro Magnum
a professional performer
wall canopy rangehood
°
professional styling
°
3 chimney options
°
600 cfm for 30” & 36”
°
1200 cfm for 48”
°
3 halogen lights for 30” & 36”
°
4 halogen lights for 48”
°
3 speed control
°
integrated control panel
°
stainless steel baffle filters
°
convertible to recirculating*
°
top or direct rear venting
°
built-in mounting system
°
sone range: 4.5 - 7.0
°
3 1/4” x 10” duct for 30” & 36”
°
2 - 3 1/4” x 10” ducts for 48”
°
* it is highly recommended that
professional style cooking always be
vented to the outside.
Size/Color/Model #
30 Stainless
36 Stainless
48 Stainless
6059890
6059891
6059892
Professional Collection
The Pro Magnum offers a
good value in the professional
ventilation category. Top or
direct rear venting and three
chimney options make the Pro
Magnum the most versatile
and easy to install Pro hood on
the market.
30” High Backsplash
a
30” high, mounts to the wall beneath the
c
rangehood for a coordinated look
30 X 30 Stainless
c
36 X 30 Stainless
e
48 X 30 Stainless
s
Duct Transition Kit
For 48” model only, transitions two 3 1/4” x
s
10” openings to one 10” round opening
o
Galvanized Steel 6000002
r
Charcoal Filters
For recirculating installations, high quality, heavy
i
duty filters ensure the removal of smoke and
odors from the kitchen. Some ductwork is
e
required to exhaust the unit out of the cabinet.
For 48” model, you must order two of part
s
#6093034, one kit for each motor
p.o. box 435 • Wayland, MA 01778 • tel: (508) 358-5353 • fax: (508) 358-5730 • e-mail: info@faberonline.com • www.faberonline.com
620000095
620000097
620000098
6093034
.
Note: The Pro Magnum comes standard
WITHOUT A CHIMNEY. A telescopic
chimney kit or full width duct cover is available separately.
Telescopic Chimney Cover
24” wide, extends to accomodate 8 - 9 foot
ceilings
24 Stainless
Full Width Duct Cover
12” high, extends full width of the hood
30 Stainless
36 Stainless
48 Stainless
6097336
6097337
6097338
6097339
25
"
25
"
Dimensional Diagrams
1/2”
3/8”
3
1/2”
1/4”
22
1/4”
23
1/2”
3/8”
4
Rectangular Hole which fits over the two 3 1/4” x 10”
exhaust openings on the rangehood
4”
3/8”
3
1/2”1/2”
14”
5/8”
2
3/4”
9
WITH TELESCOPIC CHIMNEY KIT WITH FULL WIDTH DUCT COVER
Pre-Planning Your Ductwork - Important: Consult the installation instructions before you begin installing this rangehood.
The Pro Magnum can be vented to the top or directly out the back.
Make your ductrun as straight and short as possible. The ductrun
should not exceed 35 equivalent feet if ducted with 3 1/4” by 10”
rectangular duct or 55 equivalent feet if ducted with 10” round
ductwork (when using Duct Transition Kit 6000002 for 48” model
only). Count 45º angles as 3 feet, 90º elbows as 5 feet, and 90º at
elbows as 12 feet.
Hole for Wiring Cable
30” AND 36” MODELS
For best results, use no more than three 90° elbows. Make sure
that there is a minimum of 24” of straight duct between elbows
if more than one is used. Do not install two elbows together. If
you must elbow right away, do it as far away from the hood’s
exhaust opening as possible.
48” MODEL
Hole for Wiring Cable
OPTIONAL DUCT TRANSITION KIT DIMENSIONS (48”MODEL ONLY)
For 48” model, use two 3 1/4” by 10” rectangular duct runs or use the optional Duct Transition Kit shown here. This kit cannot be used
with the Telescopic Chimney Cover because it is too large to fit behind the cover. The Duct Transition Kit will fit behind the Full Width
Duct Cover.
WARNING! Product specifications are subject to change without notification. Consult the installation instructions before you begin installing this rangehood.
Hole for Wiring Cable
Rev.06/08
Loading...