FAAC 1506-080 User Manual
Owner’s Manual
Models 1506 and 1504
Programmable Stand Alone Digital Keypad Entry Devices
DoorKing, Inc.
120 Glasgow Avenue
Inglewood, California 90301
U.S.A.
Phone: 310-645-0023
Fax: 310-641-1586
www.doorking.com
P/N 1506-065 REV C, 9/01
Copyright 2001 DoorKing, Inc. All rights reserved.
Page 2
Use this manual with the following models
1506-080, 1506-081, 1506-082, 1506-083, 1506-084, 1506-085, 1506-086, 1506-090, 1506-091,
1506-092, 1506-093, 1506-094, 1506-095, 1506-096, 1504-080, 1504-082, 1504-083, 1504-084,
1504-085 and 1504-086 Digital Keypad Entry Devices with circuit board 1506-010, Rev G and
Higher.
DoorKing, Inc. reserves the right to make changes in the products described in this manual
without notice and without obligation of DoorKing, Inc. to notify any persons of any such revisions
or changes. Additionally, DoorKing, Inc. makes no representations or warranties with respect to
this manual. This manual is copyrighted, all rights reserved. No portion of this manual may be
copied, reproduced, translated, or reduced to any electronic medium without prior written consent
from DoorKing, Inc.
Permission is granted to reproduce pages 24 and 25 in this manual.
Page 3
Page 4
Table of Contents
IMPORTANT NOTICES............................................................................................................................................6
SECTION 1 – INSTALLATION
1.1 Mounting Dimensions...............................................................................................................................7
1.2 Wiring .......................................................................................................................................................9
1.3 Wire Diagram............................................................................................................................................10
1.4 Terminal Identification ..............................................................................................................................11
1.5 Aiphone Intercom Station Connections....................................................................................................12
1.6 Slave Keypad Wiring................................................................................................................................13
SECTION 2 – PROGRAMMING
2.1 Master Code.............................................................................................................................................15
2.2 Relay Strike Time.....................................................................................................................................15
2.3 X-Strikes Programming ............................................................................................................................15
2.4 Programming Four-digit Entry Codes.......................................................................................................16
2.5 Erasing Individual Four-digit Entry Codes................................................................................................16
2.6 Erasing ALL Four-digit Entry Codes.........................................................................................................16
2.7 Four-digit entry Code Divide Number.......................................................................................................16
2.8 Programming Five-digit Entry Codes .......................................................................................................17
2.9 Erasing Individual Five-digit Entry Codes.................................................................................................17
2.10 Erasing ALL Five-digit Entry Codes .........................................................................................................17
2.11 Five-digit Entry Code Divide Number.......................................................................................................17
2.12 Hold Boundary Programming...................................................................................................................18
2.13 Time Zone 1 Boundary Programming ......................................................................................................18
2.14 Time Zone 2 Boundary Programming ......................................................................................................18
SECTION 3 – OPERATING INSTRUCTIONS
3.1 Four-digit Entry Codes..............................................................................................................................19
3.2 Five-digit Entry Codes..............................................................................................................................19
3.3 Request to Exit Input................................................................................................................................19
3.4 Door Open Input.......................................................................................................................................19
3.5 Hold Feature Operation............................................................................................................................20
3.6 Time Zone Operation ...............................................................................................................................21
SECTION 4 – APPENDIX
4.1 Troubleshooting........................................................................................................................................23
4.2 Data Tables..............................................................................................................................................24
Log Sheet .................................................................................................................................................................25
Page 5
2.15
IMPORTANT NOTICES
• Prior to starting the installation, become familiar with the instructions, illustrations and wiring
diagrams in this manual.
• Never mount this device to a moving gate or gate panel, or next to a gate that causes
vibration to the fence, such as a spring-loaded pedestrian gate. Continuous vibration from
moving or slamming gates can cause damage to the unit in time.
• WARNING! If this entry system is used to control a vehicular gate with
an automatic gate operator, the entry system must be mounted a
minimum of ten (10) feet away from the gate and gate operator, or in
such a way that a person cannot operate the entry system and touch
the gate or gate operator at the same time.
• Always disconnect power when performing service on the system.
• If the unit is mounted outdoors, be sure that the wiring to the unit is designed for direct under-
ground burial, even if the wire is run inside a conduit.
• Surge suppression is recommended on the low voltage input power line.
• Instruct the end user on the safe and proper operation of this device.
• Instruct the end user to read and follow these instructions. Instruct the end user to
never let children play with or operate any access control device. This Owner’s
Manual is the property of the end user and must be left with them when installation is
complete.
Page 6
SECTION 1 - INSTALLATION
1.1 Mounting
Surface mount units can be mounted directly to a wall or pilaster, or they can be mounted using a
gooseneck mounting post (p/n 1200-045 or 1200-046).
5.25
4.375
2.5
1 2 3
654
6.25
2.5
.875
987
#0
*
.25
3.375
1506 Surface Mount
10.0 5.25
2.5
2.5
1
7 8 9
32
654
#0*
6.125
.875
3.0
2.875
.875 Dia
1.31
1.25
5.0
Model 1504 Surface Mount
Page 7
The flush mount keypad consist of two parts, the keypad and the rough-in box. Mount the rough-in
box and wiring first, and then install the keypad into the rough-in box.
.25
1 2 3
*
7.125
8.375
654
987
#0
4.0
6.625
4.375
.875
4.25
.875
.875
5.375
4.25
10-24 STUD
2.56
.75
1.25
4.375
FLUSH
MOUNT
KEYPAD
2.0
.25
7.0
2.252.251.25
4.05.625
.875
.25
2.875
3.875
1.875
.75
2.125
ROUGH
IN
BOX
ROUGH-IN BOXFLUSH KEYPAD
Page 8
Loading...