Manual FältCom ECII SE Eng Page 1 of 36
Version: 5.2
Updated: 2006-10-25
FältCom ECII SE
Manual and installation instructions
Manual FältCom ECII SE Eng Page 2 of 36
1 Table of contents
1 TABLE OF CONTENTS ................................................................................................... 2
2 NOTES.............................................................................................................................. 4
3 COPYRIGHT..................................................................................................................... 4
3.1 Description of goods................................................................................................. 4
3.2 Warranty................................................................................................................... 4
3.3 Updates.................................................................................................................... 5
3.4 Repair return procedure........................................................................................... 5
3.4.1 Service form......................................................................................................... 6
4 GENERAL.........................................................................................................................6
4.1 Contents of packing.................................................................................................. 6
4.1.1 System components ............................................................................................ 6
5 INTRODUCTION .............................................................................................................. 6
5.1 Foreword.................................................................................................................. 6
5.2 Product description................................................................................................... 6
5.2.1 Design and function............................................................................................. 6
5.2.2 Multiple lift phone connection .............................................................................. 6
5.2.3 Programming and testing..................................................................................... 6
6 INSTALLATION INSTRUCTIONS ................................................................................... 6
6.1 Recessed mounting.................................................................................................. 6
6.2 Frame mounting....................................................................................................... 6
6.3 Mounting behind the car operating panel................................................................. 6
6.4 Connection to alarm button...................................................................................... 6
6.4.1 Closing alarm button function .............................................................................. 6
6.4.2 Separate alarm button(s)..................................................................................... 6
6.5 Connection to telephone line.................................................................................... 6
6.5.1 Connection to telephone exchange and other devices........................................ 6
6.5.2 Connection with separate suspension cable ....................................................... 6
6.5.3 Flat cable ............................................................................................................. 6
6.5.4 Connection via existing cable .............................................................................. 6
6.6 Connection of voltage feed ...................................................................................... 6
6.7 Connection to loop amplifier..................................................................................... 6
6.8 Connection of external pictogram ............................................................................ 6
7 PROGRAMMING.............................................................................................................. 6
7.1 Standard functions ................................................................................................... 6
7.1.1 Activation of programming mode......................................................................... 6
7.1.2 Reset of all settings.............................................................................................. 6
7.1.3 Input of alarm numbers........................................................................................ 6
7.1.4 Closing alarm button function .............................................................................. 6
7.1.5 Test alarm to test the installation......................................................................... 6
7.2 More available functions .......................................................................................... 6
7.2.1 Change of time delay for alarm button................................................................. 6
7.2.2 Connection via telephone exchange.................................................................... 6
7.2.3 Activation of automatic test alarm........................................................................ 6
7.2.4 Answering function............................................................................................... 6
7.2.5 Alarm mode.......................................................................................................... 6
Manual FältCom ECII SE Eng Page 3 of 36
7.2.6 Busy line function................................................................................................. 6
7.2.7 Battery alarm receiver.......................................................................................... 6
7.2.8 Simplified acknowledge ....................................................................................... 6
7.2.9 Disconnection of acknowledgement.................................................................... 6
7.2.10 Change of alarm flashing sequence................................................................ 6
7.2.11 Programmable alarm type............................................................................... 6
7.2.12 Unit ID.............................................................................................................. 6
7.2.13 Info alarm......................................................................................................... 6
7.2.14 End-of-alarm.................................................................................................... 6
7.2.15 P100 alarm protocol ........................................................................................ 6
7.2.16 Dial tone detection........................................................................................... 6
8 ALARM RECEIVING ........................................................................................................ 6
8.1 Alarm call.................................................................................................................. 6
8.1.1 Acknowledging an alarm...................................................................................... 6
8.1.2 Speech exchange................................................................................................ 6
8.1.3 Termination of active alarm mode ....................................................................... 6
8.1.4 Forwarding a call.................................................................................................. 6
8.2 Calls to a lift phone................................................................................................... 6
9 TROUBLESHOOTING ..................................................................................................... 6
9.1 Lift phone cannot be programmed........................................................................... 6
9.2 Lift phone unable to call up...................................................................................... 6
9.3 Lift phone calls up automatically at power on.......................................................... 6
9.4 Whistling sound from loudspeaker (at alarm sequence).......................................... 6
9.5 Disturbance during voice communication ................................................................ 6
9.6 Technical support..................................................................................................... 6
10 TECHNICAL DATA.......................................................................................................... 6
11 PROGRAMMING KEY MAP ............................................................................................ 6
12 CONTACT INFORMATION.............................................................................................. 6
Manual FältCom ECII SE Eng Page 4 of 36
2 Notes
We would like to thank you for placing your confidence in Fält Communications AB and are
convinced about the choice of one of our security products will fulfill your expectations. In
order to operate this FältCom ECII SE correctly we would ask you to read this manual
carefully.
3 Copyright
This document belongs to Fält Communications AB, and may only be reproduced, adapted or
transcribed after written permission from copyright proprietor. Copyright © 2005
3.1 Description of goods
Hereby Fält Communications certifies that this product is in compliance with essential
requirements and with other relevant regulations that is evident of directive 1999/5/EG and
the following standards:
Emission EN50801-1
EN12015
Immunity EN50082-1
EN120016
Telecom TBR21
The equipment has been approved in accordance with Council Decision 98/482/EC (CTR 21)
for pan-European single terminal connection to the public switched telephone network
(PSTN). However, due to differences between the individual PSTN provided in different
countries, the approval does not, in itself, give unconditional assurance of successful
operation on every PSTN network termination point. In the event of problems, please contact
your equipment supplier.
It also complies with requirements according to EN81:1-2, EN81:28 & EN81:70.
Umeå, August 2005
Rolf Sandberg
CEO, Fält Communications AB
3.2 Warranty
There is a 1-year warranty (12 months) for manufacturing failure or material failure
commencing with the delivery date.
Manual FältCom ECII SE Eng Page 5 of 36
Warranty does not include:
- Incorrect or careless usage
- Damages caused by thunderstorms or air pollution.
- Vandalism or damage.
- Normal wear
Fält Communications AB reserves the right to determine if the product will be repaired or
replaced. Warranty ceases to be valid if defects occur due to incorrect use, or other method of
application, or context that has been specified in this manual.
3.3 Updates
Visit our web site to get access to the latest updates for market information and technical
documentation. Following information can be found:
- Product surveys
- Market material
- Updated user manual
- Software and available updates
- Installation and maintenance instructions
- Contact information
www.faltcom.com
3.4 Repair return procedure
Fält Communications AB only accepts returns, which are accompanied by a completed
Service Card, which can be found in the section Service form. This form can also be
downloaded from our web site. If the product is purchased from one of our distributors the
buyer must first contact the distributors for assistance.
All returns must be sent well packed with freight paid to the address:
Fält Communications AB
c/o BL Elektronik AB
Furuhedsvägen 1
SE-952 31 KALIX, Sweden
Repaired products are sent to customers as a regular post parcel with freight paid on the
assumption that the product is included by warranty. If the investigation shows that there are
no defects on the returned product the customer is charged with a service fee and freight
charge. The customer can ask for a quotation for repair of product not covered by warranty.
Manual FältCom ECII SE Eng Page 6 of 36
3.4.1 Service form
Manual FältCom ECII SE Eng Page 7 of 36
Manual FältCom ECII SE Eng Page 8 of 36
4 General
4.1 Contents of packing
Packing for FältCom ECII SE contains following parts:
Art No. 2160 - FältCom ECII SE Complete, includes:
- Art No. 2156 FältCom ECII SE
- Art No. 2138 Mounting frame
- Art No. 2019 Mounting Kit ECII
- Art No. 2022 ECII Sticker
- Art No. 2014 SE Programming Guide
Art No 2161 - FältCom ECII SE COP Complete, for mounting behind the car operating panel
includes:
- Art No. 2157 FältCom ECII SE COP
- Art No. 2032 Mounting Kit Behind COP
- Art No. 2022 ECII Sticker
- Art No. 2014 SE Programming Guide
Art No 2163 - FältCom ECII SE ALBU Complete, with integrated alarm button includes:
- Art No. 2159 FältCom ECII SE ALBU
- Art No. 2171 Mounting frame
- Art No. 2019 Mounting Kit ECII
- Art No. 2022 ECII Sticker
- Art No. 2014 SE Programming Guide
4.1.1 System components
There are a large variety of available system components that can be ordered separately from
Fält Communications AB or from our distributors.
For more information about them, please visit our web site www.faltcom.com
5 Introduction
5.1 Foreword
We recommend a carefully reading of this user manual before FältCom ECII SE is put into
operation, to ensure that the product is used safely and effectively.
FältCom ECII SE should only be used in the context for which it is intended. All other form of
usage will be considered as being solely the users own risk. Only qualified persons are
permitted to install, program and start-up this product. Start-up is only allowed after the
product has been properly installed. As a consequence Fält Communications AB disclaims all
Manual FältCom ECII SE Eng Page 9 of 36
responsibility for possible defects, operational disturbance, accidents etc. caused by lack of
knowledge or carelessness from the user. The same principle is valid for all not approved
changes to the product.
Fält Communications AB reserves the right to make changes in the product for functional or
commercial reasons. The company is not forced to immediately update reference manuals.
5.2 Product description
The FältCom ECII SE is alarm equipment for the PSTN network with built in duplex speech
communication designed for installation in lifts.
The FältCom ECII SE is a dialing alarm transmission unit with built-in voice communication
function, intended for installation in passenger lifts. When a lift passenger presses the button
for alarm/emergency signal, the lift phone automatically calls up an alarm centre or some
other predefined alarm receiver and indicates where the alarm comes from. At the same time,
voice communication is established and the person in distress can talk to the staff at the
alarm centre, from where help will be dispatched.
5.2.1 Design and function
The user only sees the lift phone as a discreetly designed panel with perforated screen plate
for the loudspeaker and microphone. The lift phone is activated with the standard alarm
button in the lift or, if required, with a separate alarm button. When someone presses the
alarm button for more than 4 seconds, the alarm calling process is activated in the lift phone.
This time delay can easily be programmed to between 2 and 30 seconds.
The lift phone design also facilitates mounting. Loudspeaker, microphone, all the electronics,
the keys for programming and testing, as well as all connection points are integrated in one
single unit. This means quick and easy installation as well high reliability in operation. The lift
phone speaker sound is easily adjusted with a hidden trim pot.
Lift phone FältCom ECII SE
Manual FältCom ECII SE Eng Page 10 of 36
On the lift phone’s front plate, there are two pictograms and two single colored LED (yellow
and green), which is normally off. The left LED becomes yellow when an alarm call is in
progress and the right LED becomes green when the alarm has been received by an alarm
centre and a speech connection is established. The green LED is also used to indicate
programming mode. The LED can be programmed to other light sequences, see section
Programming for more information. Note that with a separate device, external pictograms can
be activated, se section Connection of external pictogram.
The lift phone can be mounted recessed in the cage ceiling/wall, or mounted in a frame,
which eliminates the need to make other holes than those for the cables.
Depending on the design of the button & display plate, it may also be possible to install the lift
phone in a prepared space behind the plate. There is a version of the lift phone with a
completely flat panel, specially intended for such mounting. Contact your local distributor for
more information.
The connection of the lift phone requires one cable to the alarm button in the lift and one twowire cable to the lift engine room for connection of a standard analogue telephone line. It is
possible to use a separate suspension cable of the type round cable or flat cable. As an
alternative, two unused wires in the existing cage cable can be used. It is very important that
the cable is fastened properly. For the separate suspension cable, there is a special mounting
kit, which includes the necessary mounting parts.
The FältCom ECII SE consumes very little power and can be supplied by the voltage from the
telephone line. Separate power supply is only required if several lift phones are connected to
the same telephone line or if the line voltage is below 32 VDC. See more under section
Technical Data.
100 mm
100 mm
Loudspeaker mesh
LED
Microphone hole
Keypad
Terminal block
23 mm
Adjustment of sound
Manual FältCom ECII SE Eng Page 11 of 36
5.2.2 Multiple lift phone connection
Several lift phones may be connected to the same telephone line. When one of the lift phones
has established a connection, the other ones will not be able to use the line; a busy tone will
instead be heard in the loudspeaker. When the line becomes free, the alarm call will be
connected automatically.
Installation of two or more FältCom ECII SE on the same telephone line requires a separate
power supply to the lift phones. The lift phone outlet marked DC is then connected to the
existing emergency power supply of the lift via a special DC/DC converter. If no power supply
is available a separate emergency power source with a built-in battery can be used. FältCom
ECII SE can then also send information about the battery status to the alarm central. Both
products are described in the product catalogue.
A total of maximum six lift/emergency phones may be connected on the same subscription.
Ordinary telephones, fax machines, modems or other types of alarm transmitters must not be
connected to the same telephone line as FältCom ECII SE because it might disturb the
functionality.
Manual FältCom ECII SE Eng Page 12 of 36
5.2.3 Programming and testing
On the back of the lift phone, there is a keypad used for programming call numbers, function
selection, and testing. All such settings are made during the installation and, normally, no
subsequent changes are required. It is also possible to remotely program the lift phone with a
special Windows program and a modem. Contact your local distributor for more informatio n.
The FältCom ECII SE is capable of calling 6 alarm receivers or standard telephones with tone
selection.
The lift phone can be programmed to send a test alarm to a specific test alarm receiver with
an interval of 1–9 days. This alarm tests the lift-phone electronics and the telephone line.
The lift phone can also be programmed to answer an incoming call automatically after four
ringing signals. In this case, tones are heard in the receiver when the call is connected.
If an emergency power supply is connected, the lift phone automatically can send an alarm if
the battery is bad and need to be replaced. A special telephone number for the battery alarm
can be programmed.
See Programming section for detailed programming instructions.
6 Installation instructions
Only competent and qualified personnel may install the FältCom ECII SE. Knowledge,
technical skill and correct equipment are required for safe and efficient installation.
Mind your own safety when installing FältCom ECII SE. You must never work in an
open lift shaft without a safety harness. Be extremely careful and break current if
you work close to a voltage of 230-400V, e.g. in the lift engine room. Never
disconnect a cable before you have made sure that it is not connected to any
voltage
Start by selecting a suitable place for the lift phone. Usually, you can find an easily accessible
and yet well protected place in the lift cage ceiling. Avoid installing the phone in a corner or
behind anything that may reflect the sound. Such installation might lead to acoustic feedback
instability between the loudspeaker and the microphone. You must be able to access the
existing suspension cable and the alarm button in the lift. Also, keep in mind that you must be
able to access the back of the lift phone in order to connect cables and program different
functions. Normally, this is easier to do inside of the lift, before the lift phone is screwmounted.
Make sure that you will not saw or drill in existing cabling when you make the holes!
6.1 Recessed mounting
1. Select a suitable place according to the instructions above.
2. Drill a hole in the centre of the selected place and then make a hole with a 86-mm
rotary hole saw or drill. See the enclosed drill template.
Manual FältCom ECII SE Eng Page 13 of 36
3. Fasten the lift phone with the 4 enclosed screws. If it will not be possible to access
the lift phone from outside the lift cage, cables must be connected and the lift phone
programmed before it is mounted.
6.2 Frame mounting
1. Mark and pre-bore the holes for the lift phone frame according to the enclosed drill
template. Drill the holes for the cables to the alarm button and telephone connection
according to the drill template.
2. Fasten the frame first and then the lift phone with the enclosed screws, after the
cables have been connected and the lift phone have been programmed.
6.3 Mounting behind the car operating panel
This alternative is only possible if there is
already a prepared space for a lift phone behind
the button & display plate. There is a special
version of the lift phone which is specially
designed for mounting behind a button & display
plate.
Since the design of the display may vary, we are
not able to give exact mounting instructions
here.
Keep in mind that the microphone hole must
be aligned with a hole in the display plate. It
might become necessary to drill a new hole.
For the best sound quality, the distance between
the lift phone front plate and the display plate
should not exceed 1 mm
6.4 Connection to alarm button
1. Draw a two-wire cable (max 10 m) from the lift’s alarm button and screw the wires on
to the lift phone’s terminal block at ”ALARM”.
2. Fasten the cable with cable ties or cable clips on the outside of the lift.
Note that the alarm button in the lift cage is normally double-breaking, i.e. made for two
separate connections, one of them usually connected to a local bell and the other one used
Manual FältCom ECII SE Eng Page 14 of 36
for the lift phone. The connections must be galvanically isolated. If they are not, or if the
existing alarm button only has one connection, the button must be replaced to another type.
Please note that there is a special version of the FältCom ECII SE with an integrated alarm
button which can be used if there is no suitable alarm button available in the lift. That version
has a double breaking alarm button where one part (NC) is used for the lift phone and the
other part (NO) can be used for the alarm bell.
6.4.1 Closing alarm button function
Note that the alarm button may have closing or breaking function. Breaking function is to be
preferred and is the default setting in FältCom ECII SE. If the button has closing function, the
lift phone must be programmed to handle this. See section Programming for more
information.
6.4.2 Separate alarm button(s)
If there is no alarm button in the lift, a separate button must be installed in the cage and
marked accordingly. Note that, in order to avoid misunderstandings, there should never be
two alarm buttons in a lift cage. It is possible to connect extra alarm buttons to the unit, for
instance on top of the lift car where a repair man can be trapped. It is important that all
buttons are of the same type.
6.5 Connection to telephone line
The lift phone must be connected to a standard analogue telephone line. Normally it can also
be connected to an ISDN connection via a terminal adaptor. To minimize disturbances when
more than one FältCom ECII SE is connected to the same telephone line it is recommended
that they are connected in series, not in parallel.
If the lift phone is connected to a standard telephone jack, the jack should be located in the lift
engine room or some other room with no admittance to unauthorized persons. This is
important to make sure that the connection will not be interrupted by mistake.
6.5.1 Connection to telephone exchange and other devices
The FältCom ECII SE can be connected to an extension in a telephone exchange, provided
the connection is analogue. Digital exchanges usually have at least one analogue connection,
since many alarms, faxes and modems require analogue communication. When connecting
to a telephone exchange it must be verified that the exchange also works in case of
power failure. The lift phone has a function, which enables it to dial a zero and then wait two
seconds for the dialing tone before proceeding with the alarm number. See section
Programming for more information.
In some situations the telephone line has a function for Hot-line calling. This means that the
telephone line automatically calls up a pre-programmed number. By programming the
FältCom ECII SE with a suitable time of pause the lift phone accept that the telephone line
manages to call up the pre-programmed number. Afterwards the lift phone uses the telephone
line for intended functions. For more information read Programming.
By connecting the lift phone to a GSM adapter which simulates an analogue telephone line
the lift phone easily can send alarms via the GSM network. Contact your distributor for more
Manual FältCom ECII SE Eng Page 15 of 36
information. For all alarm communication via the GSM network it is very important that it is
investigated if the communication still works in case of power failure.
The lift phone can also be connected to a VoIP system but then a special device must be
mounted close to the lift phone. Sometimes adjustment of the equipment is needed so the
length of the tones (DTMF) from and to the lift phone is not affected by the equipment.
Contact your distributor for more information. When using such devices it is very important
that it is investigated that the telephone line still works in case of power failures.
6.5.2 Connection with separate suspension cable
Normally, a separate suspension cable of the type round cable or flat cable is used between
the lift phone and the telephone jack. A separate suspension cable usually gives better sound
quality and less interference. The required length of cable and mounting kit can be ordered
with the lift phone.
Note that the cable brackets included in the mounting kit must be used in order to guarantee
the function. The combined wall and lift-cage brackets comprise bracket, screw, washer and
cable ties.
Check carefully that the cable will not be torn off nor squeezed or rubbed between lift
cage and shaft wall.
6.5.3 Flat cable
1. Check that the cable is long enough,
with a margin, to reach the telephone
jack.
2. Fasten the cable securely until it
reaches the lift shaft wall.
3. Secure the cable with a wall bracket
according to the figure on this page.
4. Fasten the lift-cage bracket under the
lift cage with screws, and attach the
cable to the bracket. Alternatively, the
cable can be attached to some
suitable beam on the lift cage instead
of the lift-cage bracket.
5. Draw the cable to the lift phone and
connect the wires to the terminals
marked ”TELE”.
6. Fasten the cable with cable ties or
cable clips on the outside of the lift
near the lift phone.
7. Connect the two central wires in the enclosed modular connector to the suspension
cable wire, and connect the modular connector to the telephone jack in the engine
room. Mark the connection so that it will not be removed by mistake.
Manual FältCom ECII SE Eng Page 16 of 36
6.5.4 Connection via existing cable
Warning! Make sure there is no 230–400 V in cables that you will have contact with.
Normally, the existing lift cable (usually a big flat conductor cable) goes to a cage cable box,
where you may find unused wires (if any) that can be used for the lift phone. It is important
that the used wires are next to each other in the lift cable to minimize disturbances. In case of
bad sound quality a separate cable must be used.
1. Connect a two-wire cable from the unused pair in the cage cable box and draw the
cable to the terminal strip marked ”TELE”.
2. Fasten the cable with cable ties or cable clips on the outside of the lift near the lift
phone.
3. Connect the suspension cable wire to the telephone jack in the engine room. Mark
the connection so that it will not be removed by mistake.
6.6 Connection of voltage feed
Note that separate voltage feed is only required if more than one lift phone will be connected
to the same telephone line or if single-mounted to a line voltage below 32 VDC, usually an
internal telephone exchange (PABX). This limit is possible to decrease in case of a single
mounted lift phone by mounting the attached jumper marked “J1” next to the green screw
connector. Then the lift phone can be used without a separate power supply down to 22 VDC.
Note that when the jumper is mounted it is not allowed to connect the lift phone to the public
switched telephone network (PSTN) but only to a PABX. See also section Technical Data.
The voltage feed must come from a source that will work even in case of a power failure, e.g.
the lift’s emergency light system, and must go via a special DC/DC converter. This converter
is galvanically separated from ground, which is necessary in order to avoid disturbing the
telecom station. If no existing emergency power supply is available a separate emergency
power source with a built-in battery can be used. Contact your local distributor for more
information.
1. Connect a two-wire cable to the existing suspension cable wire for emergency
lighting. Measure to verify the correct voltage between the pins.
2. Connect the cable to the DC/DC converter’s input.
3. Connect the DC/DC converter to the lift phone outlet marked ”DC”.
4. Screw the DC/DC converter on the outside of the lift and fasten the cable with cable
ties or cable clips.
When connecting two or more lift phones on the same telephone line, each phone shall be
programmed for detection of occupied line:
To deactivate this function, press:
Manual FältCom ECII SE Eng Page 17 of 36
Note: this re-programming must be done while the DC/DC converter is connected.
See more under section Busy line function.
6.7 Connection to loop amplifier
To enable passengers with impaired hearing to communicate with alarm centre there is a
possibility to connect a loop amplifier. Contact your local distributor for information about
approved loop amplifier to be used with FältCom ECII SE.
Connect the output marked “LOOP AMP” to the loop amplifier. The loop amplifier must work
during power failure. Connect it to a power supply that is working during power failures.
6.8 Connection of external pictogram
It is possible to connect external lamps to indicate alarm status on the lift phone according to
EN81:70 with the system component Pictogram Driver. It contains a DC/DC-converter and
drive circuits for external lamps. It is connected to the output marked DC/DC, to 12V
emergency power and to the external lamps. There is also a system component called
Pictogram Board with same functionality as Pictogram Driver but is delivered without the
DC/DC-converter. Contact your distributor for more information.
Manual FältCom ECII SE Eng Page 18 of 36
7 Programming
All programming i.e. alarm numbers, codes to be sent and various function selections is done
with the keypad on the back of the speech unit. For practical and ergonomically reasons it is
recommended that all programming is done at (e.g. at a desk) before the FältCom ECII SE is
mounted in the lift. All programming remains in the lift phone also after it is disconnected from
the telephone line.
The keys on the keyboard have the following functions:
Programming – Starts and end of an all programming sequences.
Sequence receiver – Used when programming more than 2 alarm receivers.
Alarm receiver 1 – Phone number to alarm receiver 1
Alarm receiver 2 – Phone number to alarm receiver 2
Alarm code 1 – Used for alarm receiver 1, 3, 4, 5 and 6
Alarm code 2 – Used for alarm receiver 2
The other keys have the same function as on a standard telephone.
At each time the keys are depressed in programming mode a short tone is heard and after
each programming sequence, there is a 4-tone for successful and a 1-tone for unsuccessful
programming.
The FältCom ECII SE can also be programmed remotely. Contact your local distributor for
more information.
Manual FältCom ECII SE Eng Page 19 of 36
7.1 Standard functions
Below follows a description of the most frequent programming sequences, which will be used
by programming the FältCom ECII SE. A number of special functions are presented below the
next section.
7.1.1 Activation of programming mode
The FältCom ECII SE can be programmed only after it has been set to programming mode.
The unit must be voltage fed from the telephone line for the keys to be activated.
Breaking alarm button is default setting for the FältCom ECII SE. In order to enter
programming mode, when the FältCom ECII SE is connected to a breaking alarm button it is
necessary to press the
key and the alarm button simultaneously. Should the FältCom
ECII SE be connected to a closing alarm button or no alarm button at all, it is sufficient to
press only the key
to enter programming mode. Note that the time delay for activation of
programming mode is the same as the selected time delay for the alarm button.
An alternative way to enter programming mode is to remove the telephone wire and DC/DC
connector, press
and keep it pressed while reconnecting the telephone wire. After about
10 seconds you will automatically enter programming mode.
The green LED will flash as long as the FältCom ECII SE is in programming mode.
Programming mode is deactivated automatically after 30 ”idle” seconds (no key pressing).
Note that some exchanges (mainly ISDN) sometimes disconnect the lift phone after a shorter
time. All programming must then be done at a different location. Normal alarms are not
affected by this.
You may also deactivate it manually by pressing:
7.1.2 Reset of all settings
If the lift phone is moved to another building or if the alarm numbers are changed or if the lift
phone has been incorrectly programmed, the best thing to do may be to simply delete all the
old settings.
Reset (delete) all settings by pressing (in programming mode):
7.1.3 Input of alarm numbers
For connection to an alarm centre, the phone numbers and ID numbers specified by that
alarm centre must be used. The ID number tells the alarm centre which lift and which building
the alarm comes from. Note that if the alarm receiver is not a twenty-four-hour manned alarm
centre, it is important to enter more numbers!
The lift phone is programmed in the same way independently if it will call to an alarm central
or a telephone/mobile. An ID number must be programmed independently if the alarm
call should be made to an alarm central or to a telephone.
Manual FältCom ECII SE Eng Page 20 of 36
1. If required, reset all old settings:
2. Enter phone number for alarm receiver 1:
<Area code + telephone number (max 20 digits)>
3. Enter ID number for alarm receiver 1:
<ID-number (max 10 digits)>
4. Enter phone number for alarm receiver 2:
<Area code + telephone number (max 20 digits)>
5. Enter ID number for alarm receiver 2:
<ID-number (max 10 digits)>
For alarm receivers 3 to 6, use the keys:
, ,
and
instead
of under item 4 above.
These numbers automatically get the same ID number as alarm receiver 1.
NB! Do not forget to test the function by sending a test alarm.
If no ID number and/or telephone number have been programmed, a short signal only
will be heard in the loudspeaker when an attempt is made to send a test alarm.
7.1.4 Closing alarm button function
Breaking function is default. If the lift phone version with integrated alarm button is used it is
already connected to the lift phone alarm input. If the alarm button has closing function, the lift
phone must be programmed accordingly by programming:
Reset to breaking function by pressing:
7.1.5 Test alarm to test the installation
After completed installation, the lift phone must be tested with a test alarm. With the keypad
on the back of the phone, you may check that the alarm reaches secondary receivers, too.
1. Press the alarm button in the lift cage and check that the alarm reaches alarm
receiver 1.
2. Check that the alarm reach es alarm receiver 2 by pressing (in programming mode):
3. If there are more alarm receivers, test them by substituting
in the sequence
above by
,
etc.
Manual FältCom ECII SE Eng Page 21 of 36
Note that the alarm is transmitted 1 minute after completion of programming mode.
7.2 More available functions
7.2.1 Change of time delay for alarm button
You can change the time that the alarm button must be pressed down before an alarm is
activated. The default time is 4 seconds, but this time may be changed to between 2 and 30
seconds. Note that the selected time must always be shorter than the time posted next to the
alarm button in the lift.
<Time in seconds (02–30)>
Note that the time always must be entered with two digits. Also note that it is the delay before
activating that is programmed which means it will take additionally about two seconds before
the actual call is made.
7.2.2 Connection via telephone exchange
If the lift phone is connected to an extension in a telephone exchange, the exchange must
issue a dialing tone before it will be possible to dial the alarm number. This is usually
achieved by dialing a zero from the telephone and then waiting for the dialing tone. FältCom
ECII SE handles this by having the alarm number start with a zero and an asterisk. The
asterisk after the zero makes the lift phone wait two seconds for a dialing tone. The waiting
time is increased if you press
two or more times. Every pressing increases the waiting
time by 2 seconds.
The primary alarm number, for example, is programmed as follows:
<Area code + subscriber number>
7.2.3 Connections to telephone line with Hot-Line functions.
If the lift phone is connected to a telephone line with Hot-line function an adequate pause time
must be added so that the pre-programmed telephone number is called up. The length of the
pause might be different in different telephone exchange solutions. The time which is needed
to make the Hot-Line call has to be known. Afterwards must a sufficient number of
symbols be programmed to achieve correct time of pause.
Observe that each one of the
- symbols represents a pause time of two seconds. There is
no need to program any telephone number since the Hot-Line function takes care of that.
< + the number of
-symbols to reach adequate waiting time >
Example: Connect a standard telephone and lift up the receiver. Measure the waiting time for
Hot-Line function before the call is made. Divide the number of seconds with two. The answer
will be the number of
-symbols which must be programmed. To be sure choose one extra
-symbol.
7.2.4 Activation of automatic test alarm
This function calls a test alarm receiver to check the connection. Note that test alarm shall
only be programmed if the function has been ordered at the alarm receiver. When the test
Manual FältCom ECII SE Eng Page 22 of 36
alarm function is active the first test alarm is sent 2 minutes after exiting programming mode.
After that the test alarms is sent every N x 24 hours where N is the test alarm interval in days.
Note that the lift phone counter is reset at every time programming mode is entered and when
the power is disconnected from the lift phone.
1. Select the required test interval: 1 to 9 days. (Use a digit between 1 and 9.)
<Days (1 – 9)>
2. Enter the telephone number of the test alarm receiver
<Area code + telephone number (max 20 digits)>
3. Enter alarm code for the test alarm:
<Code (max 10 digits)>
4. To check the test alarm function:
When testing a test alarm all communication tones (DTMF) are played out in the lift phone
speaker which makes it possible to hear that the test alarm is being transmitted. Note that the
test alarm is dialed out 1 minute after exiting of programming mode.
Press the following sequence to delete the function automatic test alarm:
If a test alarm is failed the next attempt is done after 10 minutes. Totally 10 attempts are
done.
7.2.5 Answering function
It is possible to make a telephone call the lift and have a conversation with the trapped
person. Normally this function is on but it can be deactivated.
1. Press the following sequence to deactivate the function:
2. Press the following sequence to activate the function:
With two or more FältCom ECII SE on the same telephone line, one of them is programmed
as the master with ID number ”1”. The others are coded with their individual number (2-6) by
replacing the digit
with the corresponding digit.
Example:
for lift phone 2 in the chain.
For best sound quality all lift phones should be connected in series, not in parallel. The last lift
phone in the series is given identity ”1”. A total of maximum six lift/emergency phones may be
connected on the same telephone line.
See also section Calls to a lift phone for more information about call the FältCom ECII SE.
Manual FältCom ECII SE Eng Page 23 of 36
7.2.6 Alarm mode
If the alarm mode function is active the FältCom ECII SE can only receive incoming calls for 6
hours after the alarm was called out. After this time the lift phone will be closed for incoming
calls until a new alarm is triggered. To activate the alarm mode the following conditions must
be fulfilled:
• Alarm mode function is programmed
• A lift alarm has been called out
The active alarm mode can only be disabled by the phone, which receives the lift alarm, or
from the phone, which calls to FältCom ECII SE. See section Alarm receiving.
Alarm mode function is programmed with:
Manual FältCom ECII SE Eng Page 24 of 36
Where “1” is the identity of the lift from 1 - 6. Alarm mode function is disabled with:
The active alarm mode is automatically disconnected after 6 hours but will be extended with 6
hours if a new speech connecting alarm is made or if a call is made to FältCom ECII SE
during this interval.
7.2.7 Busy line function
Busy line function means that if many FältCom ECII SE is sharing the same telephone line a
busy tone is played out in the speaker if the line already is in use. A new dial out attempt is
done automatically after 60 seconds. If more than one lift phone is connected to the same
telephone line they all must be connected to external power. Press the following sequence to
activate the function:
And the following to deactivate the function:
The function needs a line voltage of minimum 20 VDC to work. If the line voltage is below this
a separate telephone line for each FältCom ECII SE is needed.
7.2.8 Battery alarm receiver
In normal cases the 1st. alarm receiver is used as battery alarm receiver together with alarm
code 1. It is possible to choose to send all battery alarms to a dedicated battery alarm
receiver with
<Area code + telephone number (max 20 digits)>
Enter ID-number for battery alarm with:
<ID-number (max 10 digits)>
Push following sequence to finish sending all battery alarms to a dedicated battery alarm
receiver.
Test the battery alarm receiver by programming:
After exiting programming mode the lift phone automatically makes a battery alarm call.
Manual FältCom ECII SE Eng Page 25 of 36
7.2.9 Simplified acknowledge
With this function it is possible to simplify the alarm receiving procedure when using a
standard telephone as an alarm receiver. The function is activated with:
and deactivated with
When the function is active, all numeric buttons (0-9) on the phone will acknowledge the
alarm and the button
disconnect the alarm call. Each time any of the buttons 0-9 is
pressed on the telephone the time until time-disconnect is reset to 180 seconds. The button
has no function at all. There will be no possibility to change to simplex mode.
7.2.10 Disconnection of acknowledgement
It is possible to completely disconnect the acknowledgement function. It means that receiving
phone only have to lift the receiver. Disconnection will be made when the receiving phone
pushes
or replaces the receiver. Each time any of the buttons 0-9 is pressed on the
telephone the time until time-disconnect is reset to 180 seconds. The button
has no
function at all. There will be no possibility to change to simplex mode.
Note! The lift phone will only make one attempt and it will only call the first alarm receiver. If
the telephone line is occupied a new alarm must be made after the call has timed out after
about 180 seconds. The function is activated with:
The function is disabled with:
7.2.10.1 Detection of occupied alarm receiver
It is possible to make the lift phone to call the next programmed telephone number if the first
telephone number is occupied without activating the acknowledgement function. A second
function must be activated which learns the FältCom ECII SE how a correct busy tone sounds
like. Since this differs between countries one has to adapt the programming depending on
country. The function is activated with:
<Country code (1-6)>
Where the country code is changed to any of the following numbers:
1. Sweden, Denmark, Iceland
2. Belgium, France, Germany, Italy, Luxemburg, Norway, Poland, Portugal, Turkey,
Netherlands, Croatia, Israel, Slovenia, Thailand
3. Austria, Finland, Greece, Hungary
4. Great Britain, Ireland
5. Spain
6. Singapore
Manual FältCom ECII SE Eng Page 26 of 36
The busy tone for the different groups looks like the following:
The function is deactivated with:
Please note that not all telephone lines in all countries follow this pattern. Some internal
switches may have a different busy tone and therefore this function must be carefully tested.
If problems occur, please contact your local telecom operator for information about your busy
tone.
The function Detection of occupied tone can also be activated without using the function
Disconnection of acknowledgement, for instance if a faster call procedure for alarm receiver 2
when alarm receiver 1 is occupied. This is done with the following programming sequence:
<Country code (1-6)>
The function is disconnected with:
7.2.10.2 Automatic disconnection
Normally a telephone line shifts polarity when the telephone is lifted and at hang up and the
lift phone FältCom ECII SE can detect this. Because of this the lift phone can disconnect a
call faster when the function Disconnection of acknowledgement is activated and the trapped
passenger does not need to listen to an occupied tone in the lift phone speaker until the call is
terminated after maximum 3 minutes. However, should a problem occur this function is
possible to disconnect with the following programming sequence:
The polarity detection is activated with:
Manual FältCom ECII SE Eng Page 27 of 36
7.2.11 Change of alarm flashing sequence
When the alarm button has been activated and an alarm is registered by the lift phone, the
LED in the FältCom ECII SE become yellow. When the alarm is acknowledge the LED
becomes green. This flashing sequence is according to EN81:70.
There is an option to change to a flashing sequence which indicates a registered alarm with
flashing green light and acknowledged alarm with fixed green light. This is done with the
following programming sequence:
Return to the yellow/green flashing sequence by programming:
7.2.12 Programmable alarm type
The normal alarm type 10 (0Ah) may be mapped to another alarm type. The function is
activated with the keyboard sequence:
<XX>
where XX represents an alarm type between 00 and 99. To restore the alarm type to the
default value, enter:
Note that FältCom ECII SE always assumes that the programmed alarm type is speechconnecting.
7.2.13 Unit ID
When a standard telephone is used as alarm receiver FältCom ECII SE can simplify the
identification of the lift phone by sending out beeps. It can be useful when many FältCom ECII
SE are sharing the telephone line and number presentation is used for identification. It is then
impossible to know from which of the up to 6 lift phones the alarm came from. The function is
activated with:
and deactivated with:
When the function is active, the FältCom ECII SE will replace the normal beep sequence with
a start beep, followed by sequence of beeps with another frequency. The number of beeps in
the sequence is controlled by the first digit in the alarm code. If the alarm code is 345678 the
lift phone will start with a beep and the play out 3 beeps with a different frequency. If the first
digit is zero, 10 beeps will be played.
Manual FältCom ECII SE Eng Page 28 of 36
7.2.14 Info alarm
A simple info alarm function can be activated by programming:
and deactivated with
When the info alarm function is active, the last sequence alarm receiver is converted to an
info alarm receiver. 60 seconds after an acknowledged alarm FältCom ECII SE will call alarm
receiver 6 and send an operating alarm of type 89 (59h) together with the first alarm code.
Observe that if the main alarm was never acknowledged, no info-alarm will be sent out. Also
this function will not dial out an info-alarm after battery alarms or test alarms.
7.2.15 End-of-alarm
To secure that a trapped passenger is released from the lift there is a function that sends a
end-of-alarm message to an automatic alarm receiver. This can only be done after an alarm
has been sent from the lift phone. To do this programming mode is entered and a special
function is activated. One minute after termination of programming mode the lift phone will
make a speech alarm with the alarm type 28d. The function is activated with the following
programming sequence:
If the alarm receiver prefers another alarm type than 28d it can be replaced with the following
sequence:
<alarm type>
where the alarm type can be between 00 and 99.
7.2.16 P100 alarm protocol
In most cases the preprogrammed alarm protocol CPC is enough to send alarms to most
types of alarm receivers. However, it is possible to change to the less usual P100 alarm
protocol with the following sequence:
To return to the CPC protocol the following sequence is programmed:
7.2.17 Dial tone detection
FältCom ECII SE has a function which makes it possible to first wait for dial tone before the
call out sequence starts. Default this function is deactivated but can be activated with:
The function is deactivated with the following programming sequence:
Manual FältCom ECII SE Eng Page 29 of 36
8 Alarm receiving
Note that the lift phone should be connected to an alarm centre. EN 81:1–2 stipulates
connection to a twenty-four-hour manned telephone. By way of exception, it is possible to use
an ordinary telephone or a mobile phone as alarm receiver. The instructions below refer to
alarm receiving with an ordinary telephone. In an alarm centre, the line is usually connected
to a computer, which automatically registers the alarm source, on the basis of the codes
transmitted by the lift phone.
All tone selection telephones (units with the keys * and #) can function as simple alarm
receivers. The telephone keypad is then used to control the alarm receiving and acknowledge
the alarm.
Note that telephones used for alarm receiving should be marked in a way that makes
everyone aware of the possibility of alarm calls. In addition, special functions for
specific telephone keys should be clearly marked.
You cannot be sure that a manual will be readily available in case of an alarm. The most
important key to learn is 4, used to acknowledge the alarm and set up the call.
8.1 Alarm call
An incoming alarm call is characterized by an oscillating tone (”chirp”) heard in the receiver.
First tone is heard after 3 seconds and next every 3:rd second. It is important that everybody
is aware of this. Therefore, note that all alarm receivers should practice the alarm handling
procedure. If the alarm receiver has not answered within 60 seconds the FältCom ECII SE will
automatically switch to the next alarm number. The lift phone waits 60 seconds before next
alarm number is dialed.
8.1.1 Acknowledging an alarm
Acknowledge the alarm with 4, ACKNOWLEDGE. A voice communication call is then set up;
speech exchange is automatic, as in a normal telephone call.
Manual FältCom ECII SE Eng Page 30 of 36
A call will be disconnected automatically three minutes after the last key pressing. With thirty
seconds to disconnection, a warning tone will be heard. To prolong the call, press 4,
ACKNOWLEDGE.
End the alarm call by pressing 0, END. If the alarm is ended with time disconnection, replaced
receiver, or lost contact and either Simple phone acknowledge or Disconnection of
acknowledgement is programmed the FältCom ECII SE will make a new alarm call to the next
programmed alarm receiver.
8.1.2 Speech exchange
If the automatic speech exchange is not satisfactory, you can change to manual speech
exchange 8, TALK and 7, LISTEN. Revert to automatic speech exchange by pressing 4,
ACKNOWLEDGE.
8.1.3 Termination of active alarm mode
If the function alarm mode activated and the product is in active alarm mode, you can finish it
by pressing the key 5, TERMINATE ALARM MODE. The call is automatically disconnected.
8.1.4 Forwarding a call
If you want to forward the alarm to the next alarm receiver, press 2, FORWARD. The alarm is
then closed, and the lift phone will call the next programmed alarm receiver.
8.2 Calls to a lift phone
If answering function is activated, or if alarm mode function is programmed, and FältCom ECII
SE is in active alarm mode, it is possible make a call to FältCom ECII SE from a tone dialing
phone or a mobile according to the following:
1. Dial the number to the lift phone.
2. After four ring signals the first FältCom ECII SE answers and sends a 3-tone.
3. Press # and ID-number to the wanted lift phone (1-6). For instance #2 for lift phone 2
in the chain. Note that #1 must be pressed by the caller even if only one lift phone is
mounted.
4. Press 4 to activate voice connection.
5. Press 5 to terminate a possible active alarm mode. Then the call is disconnected.
6. Press 7 to listen.
7. Press 8 to speak.
8. Press 0 to disconnect the call
Manual FältCom ECII SE Eng Page 31 of 36
9 Troubleshooting
9.1 Lift phone cannot be programmed
No power to the lift phone. For programming to be possible, the terminal strip marked ”TELE”
must be connected or external voltage connected via the DC/DC converter.
9.2 Lift phone unable to call up
1. Note that both alarm receivers and alarm code must have been entered. Otherwise,
the lift phone will emit a tone burst when an attempt is made to connect an alarm.
2. Check the telephone line. Measure the line voltage on the terminal strip connections
marked ”TELE” and that it shows minimum 32 VDC. See more under section Technical
Data.
3. If the Busy line function
is programmed but the lift phone is
not connected to external power the lift phone will be locked. To enter programming
mode the telephone line is first disconnected, keep
pressed on the keypad at the
same time as the telephone line is reconnected. After about 10 seconds programming
mode is activated when the Busy line function can be deactivated. The alternative is to
connect external power to the lift phone.
4. If it takes long time before the dial tone is heard, the lift phone might start to early
dialing out the telephone number and thereby causing problems. Try to activate the dial
tone detection function with:
9.3 Lift phone calls up automatically at power on
The lift phone’s alarm button has closing function but the FältCom ECII SE is set for an alarm
button with breaking function (or vice versa). See Programming section.
9.4 Whistling sound from loudspeaker (at alarm sequence)
If there is a whistling sound, when voice communication is set up during an alarm, this may be
due to acoustic feedback. Acoustic feedback may appear if the microphone and the
loudspeaker are installed too close to a flat surface, causing the sound to rebound between
them. See section Installation instructions.
9.5 Disturbance during voice communication
Install a separate suspension cable. In extreme cases, a screened suspension cable may be
required.
9.6 Technical support
Further technical supports for lift phone FältCom ECII SE is available from your local
distributor, see section Contact information.
Manual FältCom ECII SE Eng Page 32 of 36
10 Technical data
Supply voltage:
(Single mounted) None, if line voltage is higher than 32 VDC. If line voltage is
between 20 VDC and 32 VDC an external power supply is
required. This level can be even lower if the lift phone is
mounted on an internal exchange (PABX). By mounting the
attached jumper FältCom ECII SE will work without external
power supply down to 22 VDC. If also an external power
supply is connected together with the jumper the lift phone
will work down to 12 VDC. When the jumper is mounted
FältCom ECII SE is not allowed to be connected to the public
switched telephone network (PSTN).
Supply voltage:
(2-6 units on the same line) If several lift phones are connected to the same telephone
line an external power supply always is required for each
unit. The line voltage must also be higher than 20 VDC
because of the line detection function of occupied line. See
more under section Busy line function
Current consumption: At rest: 25-45 uA
Nominal: 12-60 mA
Ext. power supply: 4-16 mA
Indications: Yellow and green LED during alarm
Sound and light indication when programming
Test alarm: 1 time/day up to once every 9 days (selectable on/off)
Alarm receiver types: Contact your local distributor for information about alarm
centrals that can handle CPC protocol.
All tone selection telephones, including mobile phones, can
also be used as alarm receivers
Protocol: CPC & P100
Speech exchange: Duplex or simplex
Signaling: DTMF
Calling: Tone selection
Answering function: Automatic (selectable on/off)
Casing: Stainless sheet steel 1.5 mm. Vandal proof.
Dimensions HxWxD: 100 x 100 x 23 mm (with frame)
105 x 90 x 26 mm (behind COP)
180 x 125 x 25 mm (with frame and alarm button = ALBU)
Weight: 235 gram (with frame)
187 gram (behind COP)
310 gram (with frame and alarm button = ALBU)
Manual FältCom ECII SE Eng Page 33 of 36
11 Programming Key Map
In order for the emergency telephone to be programmed it has to be:
1) connected to the telephone line
2) be connected to the alarm button, and
3) be set to programming mode. It is assumed that an alarm button with breaking
function is used.
Programming can be initiated approximately 20 sec. after the telephone has been connected
to the telephone line. Upon completion of each programming sequence a 4-tone confirms that
the telephone has accepted the programming. If no button is pushed during a time lapse of 30
sec. programming mode is automatically deactivated.
Below follows an overview of all programmable functions in FältCom ECII SE. In the column
to the right are the possible normal values marked with “X” or shown with the actual value.
The only programming sequence that is an absolute must to make it possible to make an
alarm is marked with a gray color in the table below.
No. Programming sequence Function Def
1.
< Phone No. >
Programming of phone number to
primary alarm receiver. Max 20 digits
2.
< Phone No. >
Programming of phone number to
secondary alarm receiver. Max 20
digits
3.
Test of secondary alarm receiver
4.
< Alarm code 1 > Programming of alarm code 1. Max
10 digits
5.
< Alarm code 2 > Programming of alarm code 2. Max
10 digits.
6.
< 3-6 >
< Phone No. > Programming of phone numbers to
alarm receiver 3 to 6. Max 20 digits
7.
< 3-6 >
Test of alarm receiver 3 to 6.
8.
Sets alarm button input to Normally
Open
9.
Sets alarm button input to Normally
Close
X
10.
Activation of dial tone detection
11.
Deactivation of dial tone detection X
Manual FältCom ECII SE Eng Page 34 of 36
No. Programming sequence Function Def
12.
< 1-30 >
Delay time to activate alarm button.
Unit in seconds.
4
13.
Activation of P100 protocol
14.
Activation of CPC protocol X
15.
< 1-9 >
Time between test alarms. Unit in
days.
16.
Deactivation of test alarm function X
17.
< Lift 1-6 >
Activation of answering function 1
18.
Deactivation of answering function
19.
< Lift 1-6 >
Activation of active alarm mode
20.
Deactivation of active alarm mode X
21.
Activation of busy line function
22.
Deactivation of busy line function X
23.
<Phone No >
Phone number to test alarm receiver.
Max 20 digits
24.
Test of test alarm
25.
Deactivation of test alarm function X
26.
< Code >
Alarm code to test alarm receiver.
Max 10 digits
27.
< Phone No >
Phone number to battery alarm
receivers. Max 20 digits.
28.
Deactivation of battery alarm receiver X
29.
Test of battery alarm
30.
< Code >
Alarm code to battery alarm receiver.
Max 10 digits
31.
Activation of simple phone
acknowledge
32.
Reset of normal acknowledge
sequence
X
Manual FältCom ECII SE Eng Page 35 of 36
No. Programming sequence Function Def
33.
Disconnection of acknowledgement
function
34.
< 1 - 6 >
Disconnection of acknowledgement
function and detection of busy tone
35.
Reset to normal acknowledge
sequence
X
36.
Activation of yellow/green LED
sequence at alarms
X
37.
Activation of flashing and fixed green
LED sequence
38.
<Alarm type>
Activation of programmable alarm
type for lift alarm. Can be from 00d to
99d
10d
39.
Reset of alarm type for lift alarm to
10d
X
40.
Activation of end-of-alarm
41.
< larmtyp >
Change of alarm type for end-ofalarm
28d
42.
Activation of unit ID
43.
Deactivation of unit ID X
44.
<1 - 6 >
Activation of busy line detection. Can
be from 1-6 depending on country
45.
Deactivation of busy line detection X
46.
Activation of automatic disconnection X
47.
Deactivation of automatic
disconnection
48.
Activation of info alarm
49.
Deactivation of info alarm X
50.
Reset all settings to factory mode X
51.
Deactivation of programming mode
Manual FältCom ECII SE Eng Page 36 of 36
12 Contact information
Fält Communications AB
Kylgränd 6A
SE-906 20 UMEÅ, Sweden
Support: + 46 (0)90 18 39 27 or via e-mail: ec2.support@faltcom.se
Phone: + 46 (0)90 18 39 00 (exchange)
Fax: + 46 (0)90 18 39 29
Homepage: www.faltcom.com
Service address:
Fält Communications AB
c/o BL Elektronik AB
Furuhedsvägen 1
SE-952 31 KALIX, Sweden
Phone: + 46 (0)923 667 20
Fax: + 46 (0)923 125 40
Homepage: www.bl-elektronik.com
Loading...