EZ-ACCESS TRANSITION MODULAR ENTRY MAT User Manual

Instructions

TRANSITIONS® Modular Entry Mat

Available in 2½” height (optional Risers also offered)

10270 REV 12-15-14

CE Technical Files kept at: Enable Access, Marshmoor Works Great North Road, North Mymms Hatfield, AL9 5SD, UK

© Homecare Products, Inc. All rights reserved.

All text and images contained in this document are proprietary and may not be shared, modified, distributed, reproduced, or reused

without the express written permission of EZ-ACCESS®.

MPORTANT INFORMATION

Rated load is 850 pounds. Never exceed rated load.
Read and follow all labels, instructions, safety and maintenance

information before use.

For additional care, use or safety information, or to obtain

replacement copies, please call 1-800-451-1903 or visit

www.ezaccess.com.
Do not use if ramp is damaged or unstable.
For wheelchairs and scooters only (not intended for commercial

use).
Ramp may be slippery when wet or icy.
Use only if sufficient maneuvering room is available at both ends of

the ramp to assure safe travel when entering and exiting the ramp.
Use ramp only with a qualified helper and always use your lap belt.
It is important that you refer to your equipment's (wheelchair or

scooter) User Guide for the proper degree of incline or decline and

chair direction before attempting ramp use. Never exceed its

recommendations.

FITTING A MODULAR ENTRY MAT

The mat can be easily trimmed to accommodate lower heights and narrower
widths and, if necessary, notched to suit the doorjamb configuration.
Alternately, mat can be combined with an additional Modular Entry Mat and
one set of Risers to create a maximum height of 4¾”.

1. If door threshold is equal to the height of the Modular Entry Mat (2½”

high), use mat as is (FIG. 2, section A).

2. If door threshold is less than the height of the Modular Entry Mat (2½”

high), trim mat to the desired height, depth and/or width using a

reciprocating saw, razor knife, or hand saw (FIG. 1).

Use caution when operating any non-manual saw as serious

injury may result due to unexpected binding or pinching of
rubber mat material. Always follow tool manufacturer’s safety
guidelines.

3. If door threshold is greater than the height of the Modular Entry Mat (2½”

high), two Modular Entry Mats (shown in FIG. 2, sections A & B) along

with one pair of Risers (FIG. 2, section C) can be combined to

accommodate a rise up to 4¾” high.

With this configuration, section A must remain at its original

height (ok to trim width only).

a. FIG. 2, section B, can be trimmed to the desired height, depth

and/or width. If section B is trimmed, section C, which is used to
increase overall height, needs to be trimmed to match the depth
and/or width of section B.

b. Secure section B to section C using supplied Phillips Head

Screws.

FASTENING THE MAT

It is recommended that the mat be securely fastened.

1. ATTACHING TO WOOD
a. Place mat in desired location and ensure that

surface is free of dirt and debris.

b. Secure mat using supplied Phillips head screws

(2 each). Space screws evenly (see FIG. 2 for
placement) and drive until head is ¼” below the
mat surface.

2. ATTACHING TO CONCRETE
a. Place mat in desired location and ensure that

surface is free of dirt and debris.

b. Using a ¼” diameter masonry bit, drill a hole 2”

deep 1” from the corner edges at the taper
(FIG. 2).

Ensure the holes are free of any

residue.

c. Drive the supplied ¼” diameter mushroom

head pin anchors (two each) into the holes
with a hammer until the head is seated.

SAFETY AND MAINTENANCE

1. At all times, keep mat clear of snow, ice, dirt,

leaves, and other debris that may accumulate on
the surface.

2. Clean mat with mild soap and warm water. Rinse

well and use extra caution when mat surface is wet.

WARRANTY

Three-year limited warranty. See reverse side of
document for details.

FIG. 1

FIG. 2

Instructions

TRANSITIONS® Modular Entry Mat

Available in 2½” height (optional Risers also offered)

10270 REV 12-15-14

CE Technical Files kept at: Enable Access, Marshmoor Works Great North Road, North Mymms Hatfield, AL9 5SD, UK

© Homecare Products, Inc. All rights reserved.

All text and images contained in this document are proprietary and may not be shared, modified, distributed, reproduced, or reused

without the express written permission of EZ-ACCESS®.

FIG. 3

FIG. 4

FIG. 5

3-YEAR LIMITED WARRANTY

1. EZ-ACCESS, a division of Homecare Products, Inc., (herein referred to as Manufacturer), warrants that the equipment shall be free from defects in material and

workmanship under normal use and service for a period of 3-years from the date of original purchase. This limited warranty applies to the original purchaser only
and is non-transferable. This limited warranty is applicable to defective metal structure components only (excludes powder coated finish, applied non-skid tread,
etc.) No part of this warranty will apply to any equipment which has been subject to misuse, vandalism, negligence, alteration, improper loads, accident, improper
installation, or which has been repaired outside Manufacturer’s place of business in any way as in the reasonable judgment of Manufacturer, to adversely affect its
performance and reliability, nor to normal deterioration due to wear, tear and exposure, corrosion, or damage caused by rain, fire, earthquake or other natural
causes or acts of nature.

2. Manufacturer’s obligation and purchaser’s sole remedy under this warranty is limited to, at Manufacturer’s option, repairing or replacing equipment which is

returned to its place of business and which, upon examination, shall disclose to Manufacturer’s reasonable satisfaction to have been defective. Manufacturer will
make the repair or replacement of defective components at its own expense. If Purchaser discovers a defect, he/she must call Manufacturer at 253-249-1101 to
request a Return Authorization (RA) to return the merchandise to Manufacturer.

3. If Manufacturer determines, in its sole discretion, to replace the equipment with either a new or repaired unit, purchaser shall be responsible for a charge prorated

on the following basis: The purchaser will be allowed a credit against the purchase price of equivalent equipment at the time of return to Manufacturer, in
proportion to the percentage of the warranted service life remaining at the time of such return. Purchaser will be responsible to pay the balance of the purchase
price of equivalent equipment. Manufacturer reserves the right to require payment prior to delivery of the repaired/replaced equipment. In calculating available
credit, the remaining warranted service life will be rounded up or down to the nearest whole year. YEARS 0-1: Unit repaired or replaced; YEARS 1-2: Repair or
50% $ credit (current purchase price multiplied by credit percentage); YEARS 2-3: Repair or 25% $ credit (current purchase price multiplied by credit percentage).
This limited warranty does not cover removal or reinstallation. Manufacturer reserves the right to require Purchaser to pay for all shipping charges (Government
purchases exempt).

4. DISCLAIMER: THE WARRANTIES AND REMEDIES CONTAINED HEREIN ARE EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES, WHETHER

EXPRESS, IMPLIED OR STATUTORY, INCLUDING ANY LIABILITY ARISING UNDER ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE, STATUTORY OR OTHERWISE. HOWEVER, THAT IF ANY IMPLIED WARRANTY CANNOT BE DISCLAIMED IN ANY TERRITORY
WHERE A PRODUCT IS SOLD, THE DURATION OF SUCH IMPLIED WARRANTY IS LIMITED TO THE DURATION OF THE LIMITED WARRANTY
DESCRIBED IN THE FIRST PARAGRAPH.

5. MANUFACTURER SHALL NOT BE LIABLE UNDER ANY CONTRACT, NEGLIGENCE, STRICT LIABILITY OR OTHER LEGAL OR EQUITABLE THEORY FOR

ANY DIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES, RESULTING FROM THE USE, MISUSE OR INABILITY TO USE THE EQUIPMENT,
OR ARISING OUT OF ANY BREACH OF THIS LIMITED WARRANTY, EVEN IF MANUFACTURER HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH
DAMAGES. THE SOLE REMEDY FOR A BREACH OF THE FOREGOING LIMITED WARRANTY IS REPLACEMENT OF THE DEFECTIVE OR NON­CONFORMING EQUIPMENT OR PART. THE MAXIMUM LIABILITY OF MANUFACTURER UNDER THIS WARRANTY IS LIMITED TO THE PURCHASE PRICE
OF THE EQUIPMENT COVERED BY THE WARRANTY.

6. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This

warranty gives you specific legal rights, and you may also have other rights which may vary from State to State. Manufacturer reserves the right to change or
improve its products without any obligation to change or improve any Product previously manufactured by it.

FITTING THE MODULAR ENTRY MAT FOR USE AS A CARGO WEDGE

This versatile Modular Entry Mat also adapts to your vehicle. Many vehicles have a 1 – 3” drop from entrance to cargo floor. The
Modular Entry Mat can easily be trimmed to the contours of the vehicle’s cargo area, filling the void and providing a smooth transition
for mobility equipment access.

1. Measure height, width, and length of area to be fitted.

It is recommended that you create a cardboard template of the area before cutting.

2. Place template on top of mat and mark areas (FIG. 3).

3. Using a reciprocating saw, razor knife, or hand saw, trim as needed (FIG. 4).

Use caution when operating any non-manual saw as serious injury may result due to unexpected binding or pinching of

rubber mat material. Always follow tool manufacturer’s safety guidelines.

4. Place Modular Entry Mat in recessed area of vehicle (FIG. 5).