EYEZONE B1080PW-2 User Manual

B1080PW-2

User Manual

Mar 26, 09

FCC Notices

It’s herewith confirmed to comply with the requirements of FCC Part 15 Rules. Operation
is subject to the following two conditions:

z This device may not cause harmful interference.
z This device must accept any interference received, including interference that may

cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
residential installation. This equipment generated uses and can radiate radio frequency
energy and if not installed and used in accordance with the instruction manual may cause
harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio of television reception, which can be determined by turning the
equipment off or on, the user is encouraged to try to correct the interference by one or
more of the following measures:

z Reorient or relocate the receiving antenna.
z Increase the separation between the equipment and receiver.
z Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.
z Consult the dealer or an experienced radio TV technician for help.

CE Declaration

This device complies with CE class B.
EN55022 IEC 61000-4-4
EN61000-3-2 IEC 61000-4-5
EN61000-3-3 IEC 61000-4-6
EN55024 IEC 61000-4-8
IEC 61000-4-2 IEC 61000-4-11
IEC 61000-4-3

Printed in Taiwan R.O.C.
All contents are subject to change without notice.
All trademarks are the property of their respective owner.

CONTENTS

1. Package Contents…………………………………..………….. 1

2. Introduction……………………………………….……………... 1

3. Features………………………………………………………… 2

4. Hardware Overview…………………………..………………... 3

5. Remote Control…………………………..…………………….. 4

5.1 Entering Text or IP Address………..……………………… 4

6. Start the B1080PW-2…….…………………….………………. 5

7. Setting Up……………………………………………………….. 6

7.1 Network Setup………………………………………………. 6

7.2 FTP Setup…………………………………………………… 8

7.3 Video Setup……………………………..………………….. 10

7.4 Other Setup…………………………..…………………….. 11

8. Using the B1080PW-2…….…………………………………... 13

8.1 Play Media Files on the CF Card……………..…………. 13

8.2 Download Function………………………..……………. 16

8.3 Play the Media Files on the PC…………..……………… 19

8.4 Download/ Upload Media Files…………..……………… 22

8.5 RS-232 Function……………………………..…………….. 25

9. Http Command Function………….…………..……………….. 26

9.1 Player Control………………….………..………………….. 27

9.2 Network Setup…………………………..………………….. 28

9.3 Timer Setup……………………………..………………….. 29

10. Schedule Function………..…..…..…………..……………….. 30

10.1 Install the Schedule Software…….……..……………….. 30

10.2 Start the Schedule Software……..……………..……….. 30

10.3 Apply the Schedule on the B1080PW-2…........……….. 35

11. Optional Auxiliary Equipment……..……..…………..……….. 36

11.1 Play-Button Box………………..………………………….. 36

11.2 IR Cable……………………………..……….…………….. 36

11.3 PIR Sensor………………………..……………………….. 37

11.4 Touch-Sensor Buttons…..…………………….………….. 37

12. Troubleshooting…………………………………..……………. 39

1

1. PACKAGE CONTENTS

1. B1080PW-2

2. Remote Control

3. Audio Cable

4. Y.Pb.Pr Cable

5. S-Video Cable

6. Power Adapter

7. User Manual

8. Schedule Software

2. INTRODUCTION

The B1080PW-2 is a digital media player that plays HD WMV9 and WMA from CF memory

card without a computer.

The B1080PW-2 supports High Definition movie hardware decode acceleration, presents for

you the smoother and clearer picture, it supports high resolution video output such as 1080P /

1080i / 720P for movie theater quality video on a big screen. By connecting to Video, S-Video,

Y.Pb.Pr, VGA (resolution up to 1360 x 768), HDMI (1920 x 1080P) and Audio, you can play picture,

movie and music on any display device.

The B1080PW-2 can connect to a wired or wireless network. The B1080PW-2 features

802.11g / 802.11b wireless technology for data transfer speed up to 54Mbps / 11Mbps on a

wireless network and can connect to a wired network at speed up to 100Mbps. This function

provides you with maximum throughput for sharing and transferring digital media.

2

3. FEATURES

 Supports multiple file formats: HD WMV9 and WMA.
 Supports Video, S-Video, Y.Pb.Pr(1080i), HDMI(1080p), VGA (1360 x 768) and Audio output.
 Supports RS-232 port for computer control with ASCII command (play, stop, pause…etc).
 Connect using an Ethernet network cable at up to 100Mbps.
 Easily connect to your wireless network using 802.11g at up to 54Mbps. 802.11b is compatible

at 11Mbps.

 Wireless Signal Range: Indoors: Up to 20 – 25 meters.

Outdoors: Up to 60 – 80 meters.

 Supports WEP (Wired Equivalent Privacy) encryption technology used by wireless device.
 Schedule Function: The B1080PW-2 will auto play the designated file at the specify date.
 Touch-Sensor Buttons Function (optional)

- Press one of the touch-sensor buttons, the B1080PW-2 will play the corresponding file

automatically.

- The number of touch-sensor buttons can be customized to 12, 24 or 36 for OEM project.

- Used with various operating environment (glass, plastics and acrylic material, except

metal material), the thickness supports 3mm -5mm, and it can be customized to 5cm for

OEM project.

 PIR Sensor Function (optional)

- After sensing approaching subjects, the B1080PW-2 will play the files automatically.

- Sensing distance is up to 3 meters with an angle of 45∘.

 Supports CF memory cards. (Suggest using the high speed (150X) CF card)
 Supports HTTP command function.
 Supports Auto Key Lock function.
 Exports the Configuration Value: You can export the configuration value to the CF card.

The configuration can be modified on your PC, and can be applied to the B1080PW-2 or
others.

 Compatible with Windows Media Player 11: Play media files stored in a network computer.
 Supports FTP Auto Download Function: Connect to Remote FTP server and download

data to the CF card automatically.

 Supports Download Pause / Resume Function: Continue unfinished downloads upon next

session.

 Embedded FTP Server.
 Supports NTP Network (G..M.T) Timer.
 Supports Universal Plug and Play (UPnP) and DHCP.
 Supports SLIDE SHOW Function (interval time with 10/ 15/ 30/ 60 seconds).

3

4. HARDWARE OVERVIEW



Power Switch: Toggle between main power on & off.

 DC Input: For the power adapter. (DC 12V / 1.5A)
 VGA Output: Connects to devices that support VGA input. (LCD、projector)
 Y.Pb.Pr Output: Connects to devices that support Y.Pb.Pr input. (HDTV、projector)
 HDMI Output: Connects to devices that support HDMI input.
 RS-232 Connector: Used for computer control with ASCII command.
 RJ-45 Ethernet Connector: Connects to router or PC by RJ-45 Cable.
 Audio Output: Connects to sound input. (HDTV with amplified speaker)
 S-Video Output: Connects to devices that support S-Video input. (HDTV、projector)
 IR Input: Connects to PIR Sensor (optional) or IR Cable (optional).
 Video Output: Connects to device that support Video input. (HDTV、projector)
 “CF READY” LED: Steady green confirms that the CF card is inserted correctly.
 CF Card Socket: For CF memory card.
 “RESET” Button: To restart the B1080PW-2.

4

5. REMOTE CONTROL

1
2
3
4
5
6
7
8

9
10
11
12
13
14
15
16
17

18
19
20
21
22
23
24

Power on/ off

Select the output mode

Numeric Key

Delete last entry

Select a function or to play the selected file

Open the setup menu Mute sound

OSD display function on/ off

Auto-play function on/ off

Mute sound

Volume up/ down

Move the cursor

Confirm the selection/ entry

Go back one layer

Select the TV type (NTSC/ PAL)

Shuffle on & off

Play the file selected

View the previous/ next file

Play the previous/ next file if in playback

Select the repeat mode

Rewind/ forward movie or music files

Stop playback

Show the information of the file selected

Search video (movie) timeframe

Zoom in/ out on the movie or picture

Pause the playback or play frame by frame

5.1 ENTERING TEXT OR IP ADDRESS

 Keys need to be pressed multiple times to enter the letter correspo nding to that key.

For Example: To enter the letter “a”. you would press the “2” button twice.

 Enter The IP Address

For Example: To enter the IP address”192.168.100.100”,.
Step 1: Press “1” once, then “1” is displayed, and the color of “1” is orange.
Step 2: When the color of “1”turns white, press “9” once, then “9” is displayed.
Step 3: Repeat steps 1 and 2 to enter and complete the IP address.

5

6. START THE B1080PW-2

 Power On

z Insert the CF memory card that has Picture, Music, Movie or WMV9 files.

z Press the “POWER” button to power on the B1080PW-2, then press the “TV MODE” button to

select the output mode.

 Status After Power On

z Status 1: If the “AUTOPLAY (Movie or Picture)” function is enabled and there are m ovie or

picture files on the CF card, the B1080PW-2 will auto play movie or picture files on the CF

card after power on.

z Status 2: If the “AUTOPLAY” function is disabled, after power on the main menu will appear

as shown in the following figure. There are two groups in the main menu (“/mnt/CF” and

“SETUP”).

NOTE：

1. The pop-up window that shows the state of wireless will appear later, if the wireless network is

enabled when the B1080PW-2 is turned on.

2. The pop-up window that shows the IP address will appear later, if DHCP mode is selected when

the B1080PW-2 is turned on.

 Power Off: Press the “POWER” button again to power off.

6

7. SETTING UP

 In the main menu, using the “▼” button on remote control to select the “SETUP” item, then

press the “ENTER” button. You will be presented with the B1080PW-2 settings screen.

 You can also press the “SETUP” button on remote control to directly open the settings screen.

(If there is file that is being play, please stop first.)

 There are four groups of sub-menu in the main menu (“Network Setup”, “FTP Setup”, “Video

Setup” and “Other Setup”).

 In the settings screen, you can use the “▲、▼、

▲、▼

” buttons to select an item, and press the

“ENTER” button to confirm the selection.

 Press the “SETUP” button on remote control to save and quit the settings screen.

7.1 NETWORK SETUP

 Network with: Select your network connection Disable/ RJ45/ Wi-Fi.
 IP Assigned by DHCP: If you have a DHCP-enabled router, please select “On”, then the router

will automatically assigns an IP address to the B1080PW-2. If you don’t have a DHCP –enabled
router, select “Off” and type the network information in “Assign IP Address”.

7

7.1 NETWORK SETUP (continued)

 Assign IP Address: If the B1080PW-2 is connected to a network without a DHCP server or you

want to use Local FTP Server function, enter the fixed IP address, Mask, Gateway and DNS for
the B1080PW-2.

PS. Refer to 5.1 for how to enter IP address by remote control.

NOTE: Before setting the IP address, Mask, Gateway and DNS, check the network information of

your PC. Please follow the steps below to get the network information of your PC.

Step 1: Click on “Start” → “Run” and type in “command”, then press “ENTER”.

The MS-DOS window will appear, type in “ipconfig” and then press “ENTER”

to get the network information.

Step 2: Assign IP Address, Mask (Subnet Mask) and Gateway (Default Gateway)

for the B1080PW-2.

Enter the same values of the Subnet Mask and Gateway, and be careful not to enter

the values of IP address that are already used by other devices on the network.

 Media Player 11 Server: Enable/ disable the Media Player 11 server.
 Wi-Fi SSID: Select the SSID that is being used by your wireless network.

NOTE: If your router does not list its SSID, then it is a hidden network, and the B1080PW-2
cannot detect it. You must manually enter your wireless settings in “Wi-Fi Encryption Setup”.

 Encryption Mode: Disable/ enable the encryption function. The B1080PW-2 supports WEP

(Wired Equivalent Privacy) encryption technology used by wireless device.

 Wi-Fi Encryption Setup

- SSID: The SSID name selected in “Wi-Fi SSID” appears here. You can also enter SSID

name manually here.

- Password: To connect to an encrypted wireless device, the password you enter here must

match the password of the device exactly. (The B1080PW-2 can use

16bit Hex WEP protection)

NOTE: The SSID and password are case-sensitive.

 Wi-Fi Connection Status: Shows the Wi-Fi information (SSID Name/ Quality/ Channel/

Connection Speed).

8

7.2 FTP SETUP

 Local FTP Server: Turn on/ off the B1080PW-2 server.

(If you use the B1080PW-2 server, please disable the DHCP function and input a fixed IP

address, Mask, Gateway and DNS of the B1080PW-2)

 Local FTP Server Setup: Set the “Port ”, “User ID” and “Password” of the B1080PW-2.

(The Default Port: 21, User ID: root, Password: admin)

 FTP Auto Download: Enable/ Disable the FTP auto download function.
 Remote FTP Download Setup

- Server IP: Enter the domain name or IP address of the FTP as was given to you by
your Web hosting provider.

- Port: The default port for FTP is 21. In most cases you should not change this number.
If the FTP site uses a port other than 21, you should enter the correct port.

- User ID: Enter the user name of the Remote FTP server.

- Password: Enter the Password of the Remote FTP server.

- FTP Path: Enter the folder path that you want to share.

 NTP Server: Enable/ Disable the NTP server function. (if the B1080PW-2 isn’t connect to

internet, please disable the NTP Server function)

 Time Setup: Set the NTP Server, Local Time and Auto Download Time here.

① NTP Server (the B1080PW-2 must be already connected to the network)

- NTP Server: Enter the NTP server IP address like: 204.152.184.72.

- G.M.T: After B1080PW-2 get the time from NTP server, it will update the G.M.T field.

- Time Zone: Use the Volume +, - and Numeric Key to set the time zone of your location.

(time zone must be set properly for the Auto-Download and Schedule

functions)

9

NOTE: GMT and applied regions

Time Zone Region Time Zone Region

(GMT-12:00) Eniwetok, Quazalen (GMT+02:00) Helsinki, Riga, Tallinn
(GMT-11:00) Midway, Ireland, Samoa (GMT+03:00) Nairobi

(GMT-10:00) Hawaii

(GMT+03:00)

Moscow, Saint Petersburg,
Volgograd

(GMT-09:00) Alaska (GMT+03:00) Baghdad

(GMT-08:00)

Pacific GMT (U.S. & Canada);
Tijuana

(GMT+03:00) Kuwait, Raid

(GMT-07:00)

Continental GMT (U.S. &
Canada)

(GMT+03:30) Tehran

(GMT-07:00) Arizona (GMT+04:00) Baku, Tbilisi, Ere van
(GMT-06:00) Mexico city (GMT+04:00) Abu Dhabi, Muscat
(GMT-06:00) Saskatchewan (GMT+04:30) Kabul

(GMT-06:00)

Eastern Coast GMT (U.S. &
Canada)

(GMT+05:00) Yekaterinburg

(GMT-06:00) Indiana (Eastern Coast) (GMT+05:00) Islamabad, Karachi, Tashkent

(GMT-04:00) Atlantic GMT (Canada)

(GMT+05:30)

Calcutta, Chennai, Mumbai, New
Delhi

(GMT-04:00) Santiago (GMT+05:45) Katmandu
(GMT-04:00) Caracas, La Paz (GMT+06:00) Sri Jayewardenepura Kotte
(GMT-04:00) Newfoundland (GMT+06:00) Astana, Dakar
(GMT-03:00) Greenland (GMT+08:00) Irkutsk, Ulan Bator
(GMT-03:00) Buenos Aires, Georgetown (GMT+08:00) Kuala Lumpur, Singapore
(GMT-03:00) Brasilia (GMT+08:00) Taipei
(GMT-02:00) Mid-Atlantic (GMT+08:00) Perth
(GMT-01:00) Capo Verde Is. (GMT+09:00) Seoul
(GMT-01:00) Azores (GMT+09:00) Yakutsk

(GMT-00:00)

Greenwich GMT; Dublin,
Edinburgh, Lisbon, London

(GMT+09:00) Osaka, Sapporo, Tokyo

(GMT-00:00) Casablanca, Monrovia (GMT+09:30) Darwin

(GMT+01:00)

Beograd, Bratislava, Budapest,
Ljubljana, Prague

(GMT+09:30) Adelaide

(GMT+01:00)

Brussels, Copenhagen, Madrid,
Paris

(GMT+10:00) Guam, Port Moresby

(GMT+01:00)

Sarajevo, Skopje, Sofia, Vilnius,
Warsaw, Zagreb

(GMT+10:00) Brisbane

(GMT+01:00) Midwest Africa (GMT+10:00) Vladivostok

(GMT+01:00)

Amsterdam, Berlin, Bern, Rome,
Stockholm, Vienna

(GMT+10:00) Canberra, Melbourne, Sydney

(GMT+02:00) Bucharest (GMT+10:00) Hobart

(GMT+02:00) Athens, Istanbul, Minsk

(GMT+11:00)

Magadan, Solomon Is., New
Caledonia

(GMT+02:00) Jerusalem (GMT+12:00) Auckland, Wellington

(GMT+02:00) Cairo

(GMT+12:00)

Fiji, Kamchatka Pen., Marshall
Is.

(GMT+02:00) Harare, Pretoria (GMT+13:00) Nuku'alofa

10

② Local Time: Set the system time manually.

NOTE: If the NTP Server and Local Time have been set, the NTP Server will be the first

priority (the B1080PW-2 is already connected to the network).

③ Download Time: Set the FTP auto-download time.

 Local HTTP Server: Enable/ Disable the HTTP command function.
 Local HTTP Server Setup: To set the “Port”, “User ID” and “Password” of t he B1080PW-2.

(The Default Port: 80, User ID: root, Password: admin)

NOTE: Press the “SETUP” button on the remote control to save the settings, and it
will auto exit the settings screen, then restart the B1080PW-2.

7.3 VIDEO SETUP

 TV Standard: Select the output TV video format (NTSC / PAL).
 NTSC Active Output: Select the output mode. (HDMI/ SD Video/ VGA/ HD Y.Pb.Pr)

You can also press directly the “TV MODE” button on the remote

control to select output mode.

 Aspecl-ratio: Se lect TV mode 4:3 or 16:9.
 HDMI: Select the HDMI output res olution among 480i / 480p/ 720p / 1080i/ 1080p.

Select the “Auto EDID”, the B1080PW-2 will scan the display device connected

and set the correct resolution automatically.

 SD Video: Select the SD output mode. (“Video/ S-Video” or “Y.Cb.Cr”)
 VGA 60Hz: Select the VGA output resolution.

(640*480 / 800*600/ 1024*768/ 1280*1024/ 1360*768)

 HD Y.Pb.Pr 60Hz: Select the Y.P b.Pr output resolution among 480p / 720p / 1080i.
 Scrolling text color: Select the text color (white/ yellow/ green/ rotation)
 Scrolling text background: Turn on/ off the text background.
 Scrolling text: Select the language of scrolling text: Latin (English)/ Japanese.

11

7.4 OTHER SETUP

 Play OSD Display: Enable or disable the OSD display.
 Auto Play

- Movies: Auto play movie files on the CF card after power on.

- Pictures: Auto play picture files on the CF card after power on. (slideshow function)

- Off: Turn off the Auto Play function.

 SlideShow Interval: Set the time each photo is shown to 10, 15, 30 or 60 seconds.
 Lock Remote Contr oller: Enable/ disable the auto ke y lock function. (The B1080PW-2 will

auto lock when there is no further input for 1 minute.)

 Lock Password Setup: Press the “Enter” button to open the “Set Password” window. Enter the

password with numeric buttons and press the “Enter” button to save the new password (The

default password: 123).