www.eyerisdigital.com
Page 1
Installation and Operating
Instruction Manual
PIN HOLE LENS CAMERA
ERM-L3360P
ERM-L3360N
Thank you for your purchase of this product.
Before attempting to connect or operate this product, please read these
instructions carefully.
Product specifications and its contents subject to change without any prior
notice.
The picture is for reference, the object as the standard.
Page 2
CONTENTS
1. General Information
- Safety Precaution
- Package contents
2. Installation of Camera
- Camera Connection
- Installation of Camera
- Tips for Camera Location
- Dimension
3. Operation Guide
- Menu structure
4. Technical Specification
5. Troubleshooting
6. Cleaning and Care
7. Maintenance and Support
Page 3
1. General Information
>Safety Precaution
1.Read these instructions carefully before commissioning the camera in order to avoid
damages caused by improper installation or use.
2.Do not harm the camera and avoid striking, shaking, etc. The camera could be
damaged by improper handling or storage.
3.Use a dry cloth to clean the camera dome cover when dirty. When the dirt is hard to
remove, use a mild detergent and wipe gently. Then wipe off the remaining detergent
with a dry cloth.
4.Do not aim the camera at bright objects. Whether the camera is in use or not, never aim
it at the sun or other extremely bright objects. Otherwise, blooming or smears may be
caused.
5.In case of outdoor use, you have to install the camera in a suitable weather protection
case incl. heating element.
6.Operate the camera with the designated voltage only.
7.Use the camera at temperatures within -10 C to +50 C and humidity below 90%.
>Package Contents
1.Indoor Color Pin Hole Lens Camera
2.Operating Instructions
3.Mounting Template Sticker
Caution
To Reduce the risk of electric shock, do not remove cover. No
user serviceable parts inside. Refer servicing to qualified
service personnel.
2. Installation of Camera
>Camera Connections
12V DC Power Supply
Use standard 12V DC output power supply with 2.1mm
standard DC power female pin. Before connect power
check power supply polarity (+ and -).
Video Output Connection
Use standard 75 Male BNC pin terminate with Co-axial
video cable then connect to camera video out BNC Female
pin.
>Installation of Camera
Mounting Template Sticker: The mentioned technical drawing is for reference only.
Actual size of Mounting Template Sticker is matched with Dome Base. Stick Mounting
Template Sticker supplied for drilling the mounting hole on the mounting surface.
>Tips for Camera Location
1.Never expose the camera to direct sunlight without additional camera housing. Keep
sufficient distance to direct heat sources.
2.Never install the camera at humid, oily or dusty locations without using an additional
housing. (Without additional housing the camera is not suitable for outdoor use)
3.Do not aim the camera towards indoor lighting, the windows, the sunlight or the sky.
(To get good pictures, camera and light should be aimed towards the object)
4.Avoid peak light as background (Also caused by reflection)
?
Page 4
>Dimension
Page 5
37 mm
37 mm
45 mm
Page 6
>Menu Structure
3. Operation Guide :
AWB
LENS
OSD MENU
AGC MAX
DAY NIGHT
BLC
FUNCTIONS
RESET
EXIT
FACTORY
SETUP
FLC
DCL
HIGH
LOW
MID
1 - 15
ON
ON
ON
OFF
OFF
OFF
OFF
TRACK
MANUAL
LOCK
AUTO
6 TO 40
OFF
BLC
DWDR
HLC
AUTO
EXT
COLOR
BW
DNR
CAM ID 0 - 255
MIRROR
CAM TITLE ON - OFF
PRIVACY
MOTION
PROTOCOL PELCO -D
BAUDRATE
2400/4800/9600/19200
LANGUAGE ENG / CHINA
RETURN
COLOR GAIN
COLOR HUE
RETURN
APERTURE
DISPLAY ON - OFF
0 - 255
0 - 255
ON - OFF
AREA
DISPLAY
SENSITIVITY
TOP
BOTTOM
LEFT
RIGHT
RETURN
ON - OFF
AREA
TOP
BOTTOM
LEFT
RIGHT
RETURN
ON - OFF
1 - 15
ON - OFF
0 - 15
0 - 60
1 - 127
1 - 96
5 - 127
ON - OFF
0 - 6
0
1 - 255
0
1 - 255
Page 9
4. Technical Specification
Video
ERM-L3360N
NTSC
ERM-L3360P
PAL
Model Number
CCD
Signal System
1/3" Sharp Color CCD
Lens
3.7mm Fixed Pinhole Lens
Effective Pixel
Horizontal Resolution
600 TVL
768 x 494
15.734KHz
59.94KHz
752 x 582
15.625KHz
50Hz
Min Illumination@ Night
Min Illumination@ Day
0.01Lux
0.2 Lux Color / F2.0
Gamma
Scanning Frequency (V)
Scanning Frequency (H)
0.45 Adjustable
S/N Ratio
More than 48db
Video Output
1V p-p, 75?
Operational
Sync System
2:1 Internal
Exposure Mode
Lens
Anti-Flicker/Manual/Fixed
DC / ELCl
AUTO
AUTO
FLK
FLK
Fixed 1/60~1/100,000sec
Fixed 1/50~1/100,000sec
Adjustable
AGC
Shutter Speed
Privacy Masking
Motion Detection
Mirror
Day/Night Mode
Digital WDR
DNR ( 2 DNR )
BLC
On /Off, Adjustable Zone
On /Off, Adjustable Zone
ON/OFF
Auto / BW / Color / EXT
Adjustable
Low / Mid / High
Off/ D-WDR / BLC / HLC
Yes, A to Z, 0 to 9, & etc
Camera Name
Color Control
White Balance
Brightness, Contrast, Sharpness, Hue & Saturation
Auto / Lock / Manual / Track
Page 10
Electrical
Current Consumption
Power Supply
100mA
12V DC Standard ±10%
Environmental
Operating Temperature
-10°C ~ 50°C
Metal
70g
Dimensional
Humidity
95%
Dimension
Weight
Housing
37 mm x 37 mm x 15 mm
5. Troubleshooting
Error Cause
No Picture Check supply voltage, check power cable and video cable
The picture is noisy Insufficient light (Properly adjusted to the camera)
The picture is too bright Too much peak light, change camera location or active back
light function of the camera
The picture is not sharp Lens focus not adjusted properly
The picture is distorted Different GND potentials between camera and monitor
(Bad connection)
Ghost Image Wrong 75 termination, shield of video cable interrupted.
6.Cleaning and Care
-Before you start to clean the camera body, disconnect the unit from power supply.
-For reasons of electrical safety never clean the camera with water or other liquid
matters and never put the camera under water.
-To clean use a soft dry cloth. Cleaning the camera inside is strictly forbidden and may
only be done by your authorized dealer.
-Since all camera functions are self adjusting and the camera does not contain any
parts or components that are subject to wear. We advice you not to open the camera
(except for the flap for settings), unless the camera appears to be defective.
Page 11
7. Maintenance and Support
1. How to request after-sale service?
When ever you want to send repairing material back to us kindly use
the same Channel where u purchased the material must with Return Material
Authorization (RMA) Form download from our website.
http://www.eyerisdigital.com/RMA%20Form.pdf
2. Following cases should be paid even within the warranty period.
A)When defects are caused by the careless handling of the user.
B)When improper or unauthorized repairs are done or when the inside is modified or
damaged.
C)Defects caused by natural disaster or power problem.
Technical Support: For any type of product operating, Function, Installation related
queries or want to know more about our product details specification or function,
contact our website or E-mail to us.
http://www.eyerisdigital.com/support.html
www.eyerisdigital.com
Loading...