Eye Lighting H573D, H573S Installation & Maintenance

Installation & Maintenance

H573D / H573S

CLASS I, IP65

Installation

The Eye Lighting H573 series’ are floodlights for outdoor
(permanent) use, designed to be operated in conjunction with
remote control gear appropriate for the lamp type and wattage
in use.

The floodlight is designed to be securely mounted on a suitably
solid horizontal surface using 2x M16 bolts.

Attach the lamp carrier to the main body by snapping its hinge
pin into the cradle on the body.

Screw the lamp in to its full extent, ensuring that it’s secure,
but not over tightened.

Ensuring the gasket and joining surfaces are clean, secure the
lamp carrier to the main body by pivoting the three screws and
tightening the wing nuts evenly.

Incoming supply cables from the control gear are terminated in
the termination box via the 20mm threaded entry.

To maintain the integrity of the enclosure’s protection against
dust and moisture ingress, cable glands or conduit fittings
rated at least IP65 must be used.

Check that the cable glands are tightened correctly.
Floodlights must be installed within the maximum

recommended distance to the control gear, as applicable to
the type used.

These instructions should be retained by the floodlight owner
for reference, and made available as necessary, to ensure
future maintenance is carried out correctly.

EL-IM003.00 Page 1 of 2

Aiming

Adjust the horizontal aiming of the floodlight by loosening the
anchor and swivel screws (not supplied) fixing the base to the
mounting surface. Using the markings on the base plate as a
guide, adjust to the required angle and tighten the screws.

Adjust the tilt by loosening the screws at the pivot point and
releasing the locking lever. Using the markings on the pivot
plate, adjust the floodlight to the required tilt angle and hold in
place by tightening the lever. Check the tilt angle is correct
and tighten the screws.

General Operation and Maintenance

Failed lamps are to be replaced promptly, or the circuit
isolated, to avoid possible control gear damage. Continual
operation on supply voltage above that nominated on the
control gear will reduce expected lamp and component life.

Clean excessive build up of foreign material from outer
surfaces of the body. Clean the lens as required with warm
water and mild detergent.

Screws requiring loosening for future service and lamp
replacement should be greased for ease of maintenance. Use
silicone base grease only, as oil base grease may damage
some components.

Luminaires with damaged or cracked glass shall be removed
from service immediately.

Continuously operated lamps should be turned off at least
once a week for 1 hour.

Lamp Replacement

The floodlight is to be wiped clean of all dust and debris prior
to disassembly.

Loosen the three wing nuts and pivot the fixing screws away
from the lamp carrier and swing the carrier away from the
body.

Replace the lamp only with a type and wattage suitable for the
control gear in use. Screw the lamp in to its full extent,
ensuring that it’s secure, but not over tightened.

Ensure gasket and joining surfaces are clean, return the lamp
carrier to its position and evenly tighten the wing nuts.

H573D/H573S

Max weight = 8.7 kg

Projected Area = 0.22 m

LAMP TABLE

Type Wattage Lamp

M1000LE/BUH

Metal
Halide

High

1000W

940W

Pressure
Sodium

1000W

Mercury 1000W HF1000PD

MF1000LE/BUH
M1000B X/U

MF1000B X/U
NH940LX

NH940FLX
NH1000

NH1000F

2

For further enquiries, please contact:

Eye Lighting
15 Industrial Ave, Wacol QLD Australia 4076
Tel: [phone] Fax: [phone]
Email: [e-mail]

EL-IM003.00 Page 2 of 2

Before carrying out any servicing on this luminaire, ensure
that the mains supply is fully isolated. High voltages,
greater than mains voltage, can be present during

Important – Safety