Eye Lighting FGY-30L-408-W-UNV-DB, FGY-50L-408-W-UNV-DB Installation Instructions Manual

FG SERIES

FLOODLIGHT LUMINAIRE

1

Eqs3325
Rev: A

INSTALLATION INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTIONS: This equipment is intended to be installed by qualified personnel. The installation must

be made in accordance with the current edition of the National Electric Code, and all applicable state and local building codes. The

final installation must be approved by the appropriate, qualified, electrical/building inspector(s). Improper Installation may result in

a risk of fire or electrical shock hazard. The instructions provided herein are made available for reference when installing the FG

Floodlight Luminaire and do not claim to represent all possible installation variations. If any portion of these installation instructions

is unclear then do not proceed with the installation and contact an EYE Lighting Representative at 1-888-665-2677.

Item

Catalog No.

Input Voltage

Watt

Input

Current

Weight

(@120 Vac)

A

FGY-30L-408-W-UNV-xx

120-277Vac

30W

0.38A

5.5lb /2.5kg

B

FGK-30L-408-W-UNV-xx

30W

0.38A

5.5lb /2.5kg

C

FGY-50L-408-W-UNV-xx

50W

0.52A

6.6lb /3kg

D

FGK-50L-408-W-UNV-xx

50W

0.52A

6.6lb/3Kg

xx= finish options

READ AND FOLLOW ALL SAFETY INSTRUCTIONS BEFORE STARTING INSTALLATION

CAUTION

 DANGER – RISK OF SHOCK- DISCONNECT POWER BEFORE INSTALLING or SERVICING LUMINAIRE.
 Luminaire installation and servicing shall only be performed by qualified personnel.
 This product uses an input 120-277VAC driver with universal wide range voltage.
 Make sure the supply voltage is the same as the rated luminaire voltage.
 Mounting surface must be specified to properly support the weight of the luminaire
 Do not install in hazardous environment.
 Do not operate in ambient temperatures above those indicated on the luminaire label.
 Use UL listed wire rated for at least 90

°

C for supply connections.

 Allow sufficient cool-down time prior to handling and/or servicing luminaire.
 Failure to provide proper luminaire grounding may result in serious personal injury.

DO NOT OPERATE IF CRACKED OR BROKEN

Introduction

This LED Flood light luminaire uses the latest in solid state lighting technology for long life, low maintenance, and high efficiency.

These FG Floodlight models can replace traditional HID lighting for area lighting.

 An internal power-factor-corrected switch mode

supply, allows for use from any nominal 120V-

277V, 60Hz AC supply without any variation in light

output.

 30W or 50W options.

 Suitable for Wet Locations, and Ambient

Temperatures from -20°C to 35°C for 50 watt

models, and -20°C to 40°C, for 30 Watt models.

 Yoke or Knuckle Mount options with adjustable

light angle.

2

Tools and Materials required: (not provided)

Installation is completed using ordinary tools including:

 #2 Phillips Screwdriver or Socket head Screwdriver
 Socket or wrench
 Mounting Hardware (provided by others)

Install Instructions:

Notes: Inspect luminaire for defects prior to installation. If defects are noticed then do not install and contact the manufacture

immediately.

STEP 1: Starting Installation

[Yoke Mount] Models FGY-30L-408-W-UNV-XX and FGY-50L-408-W-UNV-XX

Ensure supply power is turned off. Refer to Fig. 1 (for 30W) or Fig 2 (for 50W) hole pattern dimensions.

FGY-30L-408-W-UNV-DB

Use chosen hardware, level and secure luminaire to the mounting surface. Leave enough wire length to ensure that you can adjust
the fixture angle unhindered. See Fig 3
Adjust the fixture to desired angle using the adjustment screws on the side of the fixture yoke mount. See Fig 4

FIG 1 Fig 2

Fig 3 Fig 4

EQS3325