EYECLON HD Driving Image Recorder
L3 POP USER’S MANUAL
www.eyeclon.com
■ Copyright laws prohibit this manual to be copied, modified or translated without the written consent of Eyeclon.
■ The contents in this printed manual may be updated, changed or modified without notice.
For latest L3 POP operating manual updates please see Eyeclon.com.
■ Eyeclon has the right to change or modify the product and manual contents at anytime
without prior notice for improvements.
■ Customer is responsible for obeying all Federal, State, and Local laws concerning the operation of the L3 POP device.
Regulations for use may vary by region.
■ Eyeclon is not responsible for damages that can occur from using unauthorized parts and accessories.
■ The L3 POP device may NOT record videos of all accidents due to device settings and operating environments.
■ The Micro SD card should be checked periodically for errors due to wear and replaced as needed.
■ Properly install the L3 POP so that it does not interfere with the driver’s vision.
< NOTE >
02
Before Using Eyeclon’s L3 POP...
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions :
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and,
if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures :
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC CAUTION :
Any changes or modifications to the equipment not expressly approved by the
party responsible for compliance could void your authority to operate the equipment.
< FCC Statement >
03
Before Using Eyeclon’s L3 POP...
04
1. Warning and Caution .............5
2. Product Features .....................9
3. Product Overview .................12
4. Device Installation ................16
5. Basic Operation ....................21
- Using the Touch Screen
- Device Control
- LED Indicator Light
- File List Management
- Firmware Update
6. PC Viewer .............................41
7. Others ..................................53
- Product Specifications
- Troubleshooting
- Warranty
Table of Contents
01
Warning and Caution
■ Do not disassemble, repair, or remodel the device – this can cause an electric shock.
■ Unplug the power cable if you smell something burning , smoke coming out or anything unusual.
■ Do not spray water or liquid on the device as the device will not function properly.
■ Handle the device with care.
■ Plug the power cable all the way in to make sure it is connected to the device.
■ Do not use damaged power cable.
■ Do not cut, bend, or mishandle the power cable.
■ Place the device and the cables away from heat or expose to high temperature.
■ If the device is not being used for a long period of time disconnect the power cable from the main device.
as this can cause battery discharge in the vehicle.
■ Do not use the device next to flammable liquids or gas.
■ It is dangerous to operate this device while driving.
■ Use only the voltage that is provided for this device.
■ Do not apply extreme force and place heavy items on the device and the power cable.
■ Do not use wet hands when operating this device.
These cautions are provided for user’s safety and prevent damages in the device.
Please take the time to read the manual for proper product usage.
Information to prevent factors that can cause physical damage
Information to prevent service errors or system damage
Warning
Caution
!
!
!
!
Warning
06
Warning and Caution
Warning and Caution
07
Warning and Caution
■ Always keep the camera lens cleaned.
■ Make sure the device is firmly mounted during installation as it has a tendency to shift
when driving over speed bumps or unpaved roads.
■ If the device breaks, call or bring it to a service center.
Do not touch the device as your hands might get hurt from the broken parts.
■ Do not use the device for a long period of time with the vehicle’s engine turned off.
■ Collision incidents while driving are recorded and saved as continuous files.
■ Install the hardwire cable through a professional installer.
■ Use this device only with the original parts provided from the manufacturer.
■ Reception of the GPS signal can be affected by the weather, environment, or road conditions.
■ Install the device where it does not interfere with the driver’s view.
■ Do not apply excessive force on the Micro SD card or insert it in the wrong direction.
■ Store Micro SD card separately when an accident occurs or if the device is not operating properly.
■ Stay away from parking in areas with direct sunlight.
■ The resolution quality of the video can be affected by the environmental conditions.
■ Maintain the device and the power cable in a safe area.
■ Do not use the device in high temperature or humidity.
■ The recommended operating temperature is -20° ~ 60°C / -4° ~ 140°F.
■ Windows of the vehicle should be always cleaned to use the device at best.
■ Contact customer service if you feel the device is not working properly.
!
Caution
Warning and Caution
08
Warning and Caution
■ Do not use a pin or a nail to push the LCD.
■ Do not use excessive force when using the control buttons.
■ Do not use chemicals to clean the device.
■ Keep the product away from children and pets.
!
Caution
Warning and Caution
02
Product Features
■ 3.5” TFT LCD
Provides clean and clear video quality.
■ Format Free Technology
Provides automatic memory format and maximizes the stability and minimizes file errors of Micro SD Card.
Automatically overwrites files when storage capacity is needed.
■ PIP Multi Screen
Multi Screen feature allows you to view front / rear view screens simultaneously.
■ Audio / Voice Guide
Provides voice guide and alert sounds / messages.
■ Micro SD Card Format
Automatic Micro SD card format.
■ Front / Rear LED
Notifies the driver recording mode while driving, or parking.
■ 3 Axis Acceleration Sensor
Embedded G-Sensor senses the collisions and records them.
■ Various Recording
Continuous, Incident-Continuous, Incident-Parking, Parking, Manual Recording types.
■ Battery Discharge
Measures the voltage (battery) real time and prevents the vehicle from being discharged.
10
Product Features
Product Features
11
Product Features
■ Operation Temperature Sensor
Automatically senses over heating and high temperature of the devices and shuts off the power for protection.
■ PC Viewer
PC Viewer for Windows/MAC is used to watch recorded videos.
■ Location and Speed Limit Sensor
Provides information about the vehicle’s location and speed.
Compatible with Google Map and allows to check travel routes.
■ Lane Departure Warning System (LDWS)
Alerts the driver if the vehicle is outside of its lane.
■ Front Vehicle Start Alarm (FVSA)
Alerts the driver when the front vehicle starts to move from a complete stop.
Product Features
03
Product Overview
13
Product Overview
※ Check to see if any components are missing.
※ The product and manual contents can be changed or modified at anytime without prior notice
for improvements or customization.
※ Optional parts and accessories are sold separately.
■ Option
Adhesive MountMain Unit
Quick Start
Guide
Car Charger
Micro SD Card
Hardwire Cable
Rear Camera
Rear Camera
Cable
GPS Module
1. Package Components
14
Product Overview
■ Main Unit (Front Camera)
2. Product Overview
15
Product Overview
■ Main Unit (Front Camera)
Camera Lens
R-CAM
GPS Port
DC-IN
Speaker
Front LED
Microphone
Power Button
Micro SD Card
LED
LCD Screen
Power cable port
GPS module port
Rear camera port
Front camera for video recording
Voice guidance
Indicates vehicle is equipped with dash cam
Voice and audio record
Live view, playback, menu operation
Feature operation indicator light
ON/OFF button
Memory card slot (please check for insert/remove direction)
2. Product Overview
04
Device Installation
17
Product Overview
< Caution >
- It is dangerous to operate this device while driving.
- Please check if the Micro SD card is inserted correctly before connecting to power.
- Make sure the installation area is clean.
- Disconnect the power cable if you are not using the device for a long period of time.
- Handle the device with care. Do not drop the product as it may not function properly.
- Please make sure that the device is maintained in the suggested operating temperatures between -4°~ 140°F.
During extreme high temperatures or hot weathers, parking indoors is suggested.
Device Installation
18
Product Overview
< Caution >
- Push the Micro SD card until you here a click sound or recording will not start.
- Make sure there are no particles on the Micro SD card.
- It is recommended to use the Micro SD card with this device only.
- Do not remove the Micro SD card when the device is operating.
1) Insert / Remove Micro SD Card
- Refer to the above image and check the direction before inserting the Micro SD card into the slot.
- Push the Micro SD card all the way.
- When the power is, you will hear a voice guide informing Micro SD card has been inserted correctly.
Insert
Do not apply excessive force on the
Micro SD card or insert it in the
wrong direction.
Remove
Device Installation
19
Product Overview
2) Main Unit Installation
① Installation Location
Before installation, make sure the
engine is turned off. Clean the area
where the product will be installed.
※ Do not install the device where it
interferes with the driver’s vision.
② Connecting the Device and Mount
Align and attach the device to the
bottom holes of the mount.
④ Connecting the Cables
Connect all the related cables (rear
camera, GPS, power) and adjust the
camera angle accordingly.
※ Make sure the cables of different
devices (navigation, GPS, and others)
do not overlap with each other.
⑤ Inserting the Micro SD Card
Insert the Micro SD card into the
Micro SD card slot in the direction as
shown in the left image.
※Do not apply excessive force on the
Micro SD card or insert it in the wrong
direction.
③ Attaching the Device
Remove the double-sided tape and
attach the device.
① Rear Camera Cable
② GPS Cable
③ Car Charger or Hardwire Cable
①
② ③
Device Installation
20
Product Overview
3) Rear Camera Installation(optional)
Connecting to power (using car charger)
※Dash cam’s power can be still supplied with the ignition turned
off based on the model and make of the car. This can cause
battery discharge in the vehicle.
① Installation Location
Before installation, make sure the
engine is turned off. Clean the area
where the product will be installed.
② Attaching the Device
Remove the double-sided tape and
attach the device.
③ Connecting the Cable
Connect rear camera and the cable and
adjust the camera angle accordingly.
※ Make sure the installation area doesn’t interfere with the window’s
infrared rays.
Device Installation
05
Basic Operation
22
Basic Operation
■ Main Screen
LCD OFF
LCD screen OFF menu
SD Card Format
SD Card format menu
Manual Record
Manual record menu
File List
List of recorded files (recording will stop in menu mode)
Settings
Main menu settings (recording will stop in menu mode)
Front and rear live view (2CH)
Switch to front / rear view
Front / Rear View
1. Using the Touch Screen
23
Basic Operation
▶ Touch Live View screen to go back to Main Menu.
Current Date and Time
GPS Status
Voice & Audio Record
Recording Status
Settings → System Settings → Time Settings
* Will set automatically if GPS is connected
Settings → Audio Settings
MIC ON : recording / MIC OFF : not recording
REC : continuous record
EVENT : incident, manual record
GPS ON / OFF
1) Live View
1. Using the Touch Screen
24
Basic Operation
Recording Status
▶ Turn OFF Screen Saver Mode → Screen Saver Settings → OFF
▶ Touch screen to go back to Live View Screen
REC: continuous record
EVENT: incident / manual record
Voice & Audio Recording Status
MIC ON : recording / MIC OFF : not recording
GPS Signal Status
GPS ON / OFF
Current Time and Date
Shows current time and date
1-1) Screen Saver Mode
1. Using the Touch Screen
25
Basic Operation
▶ Micro SD Card Format
▶ Saved files will be deleted. Backup the files before formatting.
2) Micro SD Card Format
1. Using the Touch Screen
26
Basic Operation
Front / Rear Camera File List
Sorts the file list according to front / rear recordings
File List : Up
Moves file list up
File List : Down
Moves file list down
File List
Select the file to play from the list
HOME
Moves to Live View Screen
BACK
Moves to previous screen
3) File List
1. Using the Touch Screen
27
Basic Operation
3-1) Video Playback Screen
Video Play Time
ex) 10/60 : current play time (sec) / total play time (sec)
Number of Files
ex) 4/200 : 4th file out of 200 files
Previous
Play previous file
Play / Pause
Play or pause
Next
Play next file
BACK
Moves to file list
1. Using the Touch Screen
28
Basic Operation
4) Settings → ADAS Settings
Front Vehicle Start Alarm (FVSA)
※ To use the ADAS features, GPS needs to be connected and the
vehicle needs to be moving at a normal driving speed. ADAS
features’ accuracy can be affected by the road or weather
conditions (such as driving at night, driving through tunnels,
heavy rain and snow, road and environmental conditions).
Lane Departure Warning System (LDWS)
A voice or a tone alerts the driver if the vehicle is
outside of lane.
Alerts the driver when front vehicle starts to move from
a complete stop.
1. Using the Touch Screen
29
Basic Operation
Driving Speed
Set driving speed
* mph : 40mph, 45mph, 50mph
* km/h : 60km/h, 70km/h, 80km/h
Start LDWS
Enable the LDWS feature by ON / OFF
LDWS Installation Guide
Calibrate the ADAS settings guide
LDWS Sensitivity Settings
Use the right / left key to set the lane departure area
according to the driver’s preference
4-1) LDWS(Lane Departure Warning System)
1. Using the Touch Screen
30
Basic Operation
Red Horizon Line
Adjust device angle parallel to red horizontal line.
Blue Hood Line
Use the up/down key to align the hood with the blue line
＊If you are not able to see the hood, align against the bottom line.
▶ Align the red horizontal line first and then the blue hood line.
▶ If you touch HOME / BACK button the current screen will disappear
▶ If you cannot see the blue hood line due to the HOME / BACK buttons,
touch the screen for full screen view.
▶ Use the HOME or BACK button to save the settings.
※ Caution : it is dangerous to operate menu controls while driving.
▶ Select the vehicle type : Sedan / SUV / Truck
4-1) LDWS Installation Guide
ADAS Calibration
Blue Hood Line
Red Horizontal Line
Adjust device angle parallel to red horizontal line.
Align blue line with the front edge of the hood using the top / down keys.
If the front edge of the hood is not shown on the screen, align blue line to the lowest level.
1. Using the Touch Screen
31
Basic Operation
① / ④ : Low → High
② / ③ : High → Low
Lane Departure sensitivity level settings
▶ Set the timing of the lane departure notification alert by using the
left / right buttons. (the wider tire icons are, faster reaction to
sensitivity)
4-1) LDWS Sensitivity Settings
1. Using the Touch Screen
Lane Departure Warning System
(LDWS) Sensitivity Settings
32
Basic Operation
▶ Front Vehicle Start Alarm (FVSA) alerts the driver when the front
vehicle starts to move from a complete stop.
▶ Enable the FVSA feature by selecting ON / OFF.
▶ FVSA feature operates in front camera view mode.
※ GPS needs to be connected for this feature to operate.
4-1) FVSA(Front Vehicle Start Alarm)
1. Using the Touch Screen
33
Basic Operation
Touch Calibration
System will restart after calibration is completed
PIP
Multi Screen view – front / rear view simultaneously
Screen Saver
Settings for LCD auto OFF and screen saver
LCD Auto ON / OFF
LCD screen will turn OFF automatically
Screen Saver
Enable screen saver – 1mins / 3mins / 5mins / OFF
4-2) Display Settings
1. Using the Touch Screen
34
Basic Operation
Audio / Voice Record
Audio / voice record using the microphone
Audio / Voice Guide
Set the volume control in 3 levels (3 being the loudest)
▶ Use the HOME or BACK button to save the settings.
4-3) Audio Settings
1. Using the Touch Screen
35
Basic Operation
Memory Partition
Allocate storage capacity on memory card for recording
modes (OFF / 25% / 50%)
OFF : disable in parking mode
Collision Sensitivity
Enable the sensitivity levels (low / mid / high) of collisions
while driving or during parking
※ higher the level, more sensitive on collision
Battery Discharge Settings
▶ Use the HOME or BACK button to save the settings.
4-4) System Settings
1. Using the Touch Screen
Time Settings
System’s time settings
Enable battery discharge duration and voltage
(12v / 24v / duration)
36
Basic Operation
- Main power ON button
- Once the device is connected it will automatically turn ON / OFF by vehicle’s ignition.
Green LED light means the device will start to record.
A voice guide will alert the driver “continuous recording mode”.
- The device is set at continuous recording mode when the power is connected.
- TFT Touch LCD is used to control the menus, record collision incidents while driving or parked,
and analyze accidents.
- Incident Record during continuous recording mode when the device senses an impact or a collision.
- After the event has been recorded, Continuous Record will start again.
- Record during Parking.
- Battery Discharge features are enabled to prevent the vehicle’s battery from being discharged.
The device will automatically turn off based on the Battery Discharge Settings’ duration.
- Event (incident) and Motion Record during Parking.
- The device either senses an impact or a collision and detects a motion while the car is parked and
records the event or the motion.
2. Device Control
Power ON
Touch LCD
Event Record
Parking Mode Record
Event Record during
Parking
Control Function Description
37
Basic Operation
Continuous
Motion Detection
Parking
ON
ON
OFF
Blinks every 1 sec
Blinks every 0.5 sec
Blinks every 1 sec
Continuous Record
Motion Detection / Incident Record
Record during Parking
3. LED Indicator Light
Recording Type Rear Green LED
Front Blue LED Meaning
38
Basic Operation
Hour-Minute-Second
Year-Month-Date
Front View Recording_Recording Type
Normal
Motion
Evnet
Parking
Continuous Record
Record during Parking (motion detection)
Incident Record during driving, Manual Record
Incident Record during Parking
Dashcam
Parking
Event
ParkingIncident
▶ Recorded files are saved in Micro SD card by date and hour.
▶ Files are saved in the following format below.
4. File List Management
Recording Type Description Saved Folder
39
Basic Operation
4. File List Management
▶ Recording Time by Memory Size
Chart below is maximized recording time by storage capacity.
[ Car Charger ]
: HD+VGA 2CH / Memory Partition : 0%
▶ Storage partition can be modified manually : Settings → System Settings → Memory Partition
※ Reference numbers may vary depending on recording environment and image quality (also after firmware update).
※ Recording time is doubled when 1CH is installed.
[ Hardwire Cable ] : HD+VGA 2CH / Memory Partition : 50%
(Parking mode is available with hardwire cable connection.)
Continuous
Parking
Continuous(89%)
Incident Manual(10%)
Motion(0%)
Incident(0%)
13.4GB / 98mins
1.5GB / 10mins
0GB / 0min
0GB / 0min
16GB
Maximum Storage / Time
32GB
Maximum Storage / Time
Continuous
Parking
Continuous(40%)
Incident Manual(10%)
Motion(44%)
Incident(5%)
16GB
Maximum Storage / Time
32GB
Maximum Storage / Time
Memory Partition : 0% Percent
Memory Partition : 50% Percent
26.8GB / 196mins
3GB / 20mins
0GB / 0min
0GB / 0min
6GB / 44mins
1.5GB / 10mins
6.6GB / 48mins
0.75GB / 5mins
12GB / 88mins
3GB / 20mins
13.2GB / 96mins
1.5GB / 10mins
40
Basic Operation
5. Firmware Update
1) Select Micro SD Card
Select Micro SD Card (EYECLON) in My Computer
Right click and select “Format”
2) Micro SD Card Format
In the Disc Format Window, select the :
▶ File System : FAT32
▶ File Size : 32KB
▶ Unclick “quick format”
3) Copy the Update File to Micro SD Card
Place the file L3-POP-V1.00-000.img file into the
Micro SD card that has been already formatted and delete it.
※ file version can change based on each update.
06
PC Viewer
42
PC Viewer
1) Installation
Download the Setup.exe file at eyeclon.com or use the pre-installed file in Micro SD Card and follow the steps like below.
PC Viewer
Select English (United States) if you are located in USA.
Or select English if you are located in other countries
other than USA.
English(United States)
English
43
PC Viewer
1) Installation
PC Viewer
⑦
⑧
Download the Setup.exe file at eyeclon.com or use the pre-installed file in Micro SD Card and follow the steps like below.
44
PC Viewer
2) Main Screen / Control Keys
Functions and images of the PC Viewer can change without notice due to version update.
① Configuration / Minimize / Exit
② Main Screen
③ Control Keys
④ Acceleration Sensor Information
⑤ Navigation Map (if GPS is not connected, logo will appear)
① Open
② Previous file
③ Play / Pause
④ Stop
⑤ Next Frame
⑥ Next file
⑦ Capture
⑧ Speedmeter(mph,km/h)
⑨ Sensor
⑩ Defog
⑪ Map
PC Viewer
45
PC Viewer
3) File List
① Add File
- Click on add file button( ) and select the directory
- Drag and drop to add the files
② Delete File
- Click on either “trash” ( )or “delete” button to delete the files
③ Select Record File Type
- Use right click button to select the file type
- Files are sorted by date and time
④ Arrange File List
- Files recorded in the device are sorted in ascending order by date and time
- Files from other sources are added at the end
- Files will re-sort when you click on the file list (either ascending or descending order)
PC Viewer
4) File Zoom In / Out
5) Full Screen Mode
① File Zoom In
- Select the area of the file to zoom in
- The enlarged area is shown on the right screen
② File Zoom Out or Cancel
- Right click on screen to zoom out
① Double click on the current file for full screen view
② Double click the full screen view or click ESC button to cancel the full screen view
③ Control keys are at the bottom of the screen
6) G-Sensor Information
Detects collision incidents while driving.
PC Viewer
46
PC Viewer
① : Zoom In
② : Minimize file size
③ : Zoom Out
④ Contrast : 0~15 (0 original image)
⑤ Save : save file (image)
⑥ Print : print file (image)
PC Viewer
7) Map
8) Screen Capture
If the GPS is connected, map icon will appear on the bottom right corner.
If not, Eyeclon logo will appear.
Click on the “screen capture” button in the playback screen.
Can save or print file.
9) High Contrast
Able to capture the playback screen for a clearer view. Use the +,- buttons to zoom in / out.
47
PC Viewer
A. Complete – save settings and close
B. Apply
C. Save as
D. Reset settings
E. Cancel – close settings
F. Open file
PC Viewer
10) System Settings
Setting menu for device features.
- Continuous : set functions for continuous mode
- Parking : set functions for parking mode
- LDWS : set functions for LDWS
- Others : set functions for others
- Viewer : set functions for PC Viewer
48
PC Viewer
※ System Settings menu is at the bottom right in the PC Viewer
※ Open files with config.txt name using drag & drop feature (files with other names use open button)
49
PC Viewer
11) System Settings – Continuous Mode
Continuous mode function settings.
① Resolution Quality
: Resolution settings by Low / Mid / High
② Audio / Voice Record
: Record : ON / Disable Record : OFF
③ G-Sensor Sensitivity
: Settings for collision sensitivity by Low / Mid / High
PC Viewer
50
PC Viewer
12) System Settings – Parking Mode
Parking mode function settings.
① Recording Resolution Settings
: Resolution quality by Low / Mid / High
② G-Sensor Sensitivity Settings
: Collision sensitivity by Low / Mid / High
③ Collision Sensitivity Settings
: Collision feedback sensitivity by OFF / Low / Mid / High
④ Battery Discharge Settings (based on 12v / 24v)
: Based on the vehicle’s model, enable battery discharge settings
by OFF / 11.8V / 12V / 12.2V
⑤ Battery Discharge Duration Settings
: To prevent the vehicle’s battery from being discharged,
set the device to turn off after 12hrs / 24hrs / 48hrs / disable feature: OFF
⑥ SD Card Memory Partition
: Allocate the storage capacity for recording modes by OFF / 25% / 50%
PC Viewer
51
PC Viewer
13) System Settings – LDWS
LDWS mode function settings.
① LDWS
: Enable or disable LDWS feature by selecting OFF / ON
② Driving Speed Settings
: Basic default driving speed settings for LDWS is 40 / 45 / 50 mph
③ Vehicle Type
: Sedan / SUV / Truck
④ FVSA
: Enable or disable FVSA feature by selecting OFF / ON
PC Viewer
52
PC Viewer
14) System Settings – Others
Other mode function settings.
① Indicate Vehicle Speed Settings
: Indicate the speed of the vehicle on the screen display
by selecting OFF / ON
② Speaker Volume Settings
: Set the volume level by 1 / 2 / 3 / Mute
③ Standard Time Zone
: Time zone based on local time (UTC) / Check to select DST (Daylight Saving Time)
④ Time Settings
: Set the current time and date
⑤ Screen Saver Mode
: Set the screen saver mode by OFF / after 1min / after 3mins / after 5mins
⑥ PIP Settings
: Front / Rear camera view is shown in one screen with Multi Screen view
Enable or disable PIP by OFF / ON
⑦ LCD Auto Off
: After a certain period, LCD will automatically turn off
Enable or disable this feature selecting OFF / ON
⑧ Micro SD Card Format
PC Viewer
53
PC Viewer
15) System Settings – Viewer
Viewer mode function settings.
① Speed Measurement Settings
: Set the vehicle’s speed measurement by km/h / MPH
PC Viewer
07
Others
55
Others
98 x 63 x 30mm / 95.5g
3.9 x 2.5 x 1.2in / 3.37oz
Micro SD Card
16GB / 32GB / 64GB (FAT32 format)
Continuous Record
Incident Record
Motion Detection Record
Manual Record
Record during Parking
Front : HD (1280x720P)
Rear : D1 (720x480P)
Front : 1Megapixel CMOS Sensor
Rear : 0.3Megapixel CMOS Sensor
Description
Item
Model
LCD
Audio / Speaker
Frame Rate
Acceleration Sensor
GPS
Input Power Source
Auxiliary Power Unit
Operation Temperature
Recording Mode
Size / Weight
Capacity
Resolution
Camera
Item
L3 POP
3.5” TFT LCD
Embedded microphone, speaker
Up to 30fps (Front: 720p / Rear: 480p)
3 Axis Acceleration Sensor
External GPS port
DC 12/24V
Super Capacitor
-20° ~ 60°C / -4° ~ 140°F
Description
1. Product Specifications
Check if power cable is properly connected.
Check if power is ON.
Unplug the power cable and reconnect after 3 mins.
1. Check if location signal is recognizing the vehicle
2. Check if GPS is connected and if the vehicle is moving faster than 30~50mph
1. Check if location signal is recognizing the vehicle
2. Check if GPS is connected
Based on the angle of the location of the device, the display can be dark.
* Do not install the device on a tinted window.
Check is the GPS is connected and if it has good coverage.
Reconnect the GPS module. Check the PC’s internet connection.
Check if there are any substances covering the camera’s view.
Reconnect the camera’s cable and start again.
Check if the device is mounted firmly.
Clean the camera lens and the vehicle’s window.
LCD display doesn’t turn on in parking mode.
LCD is ON during continuous mode.
Check if audio/voice is ON in audio/voice settings menu
Check if LED settings is ON in display settings menu
Format the Micro SD Card and restart
No Power
LCD Display doesn’t turn ON
Unable to record Audio / Voice
No LED
Unable to save files in Micro SD Card
LDWS is not working
FVSA is not working
Display is too dark
Unable to see the map in the PC Viewer
Rear camera is not working
Video shakes while driving
Video quality is unclear or blurry
Condition
Description
56
Others
2. Troubleshooting
57
Others
Eyeclon provides a warranty to the original purchaser of a new Product against defects in workmanship and materials for a period of one (1) year.
If a product covered by this warranty is determined to be defective within the warranty period, Eyeclon will either replace or repair the product
at its sole option and discretion.
Products determined defective must be sent to an Eyeclon service center to obtain warranty service.
PLEASE DO NOT RETURN PRODUCT TO POINT OF PURCHASE.
Pre-authorization and shipping instructions must be obtained before sending any product to warranty service center.
Proof of purchase in the form of a receipt is required to show that Product is within the warranty period and product must have original and
legible serial number information.
TO OBTAIN WARRANTY SERVICE CONTACT EYECLON TECHNICAL SUPPORT AT :
This Warranty is subject to change without notice.
FOR COMPLETE AND UPDATED WARRANTY INFORMATION PLEASE VISIT:
www.eyeclon.com/warranties
[ North America Region ]
■ email : techsupport@eyeclon.com
■ phone : +1-949-623-8688
(9:00am to 6:00pm C.S.T. M-F)
[ Global Support ]
■ email : eyeclon@mcnex.com
■ phone : +82-70-4330-5745
3. Limited Warranty on Parts & Labor
www.eyeclon.com
EYECLON HD Driving Image Recorder
L3 POP USER’S MANUAL
Loading...