Exuav FlyTower F1 Instructions Manual

www.exuavrc.com

FlyTower F1 Instructions V1.8

Warning

Instructions for use

1, Please install ANT (must be DONE) before debugging or testing VTX（and OSD）, or lead to VTX not working properly.

2, please use proper tools to install FlyTower .It is easy to damage the PCB components by using sharp tools. (warning: Bear

in mind that screws do not install too tight between every layer, so as not to destroy the PCB and electronic components).

3, When you debug or test flight control Please remove all the propeller; Try not to test indoors, So as not to cause safety

accidents. Install the propeller before a test flight, please check again.

4, Please check and adjust ESC plate welding, thus brings all the losses and problems, or you should face the consequences.

5, Please do not fly your drone near the crowd, for all the losses from the crashed aircraft, you should face the consequences.

6, For your safety, please do not use more than 4s battery, Using more than 4s battery would cause safety risk, we will not

undertake any responsibility.

7, Before power on, please check the positive and negative pole again to make sure whether there is a short circuit .( you also

have to check that whether there is a short circuit between your motor cables and you drone’s body).

8, Please use original screws and fixings to install FlyTower.

www.exuavrc.com

Product specifications

4 in 1 ESC

PDB

Integrated

Battery Monitoring

Integrated
FC Power

Integrated

Operating Voltage

2-3S Lipo

Maximum continuous operating current

4*20A

Maximum instantaneous operating current

4*25A(10S)

Oneshort 125

YES

BlheliSuite Configurable

YES
Firmware Vision

BLHeli14.8(DYS_SN20A_MULTI)

Board Size

36*36mm

weight

8.6g

FC&VTX Board

Firmware Vision

BetaFlight/CleanFlight(NAZE)

Configure

BetaFlight/CleanFlight

VTX Power

25/200/400mW(MAX 800mW)

CH

40CH

OSD Firmware

MW OSD_1.6R

Video Camera Voltage

Any stand by 5V Video Camera

Board Size

36*36mm

weight

11.4g

Black Ants

FlyTower F1

Any Board weight

20g

total weight

27.3g

Installation height(Add air-cooling fin)

15mm/20mm

Screws

M3*16mm

Recommended Rack Plate Thickness

Not more than 3MM （ 3mm above the appropriate

extension of the screw）

The FlyTower F1 board was designed basing on NAZE32 FC and was highly integrated
with OSD, BEC，4 in 1 BL20A ESC and VTX. It gives you all the features what you need in FPV,
which makes you easily get into FPV racing. Supports a variety of aircraft.

★ Practical - Easy to access connectors
★ Configurable - Choose to use connectors
★ Stackable - Mount our 4 in 1 ESC
★ Compact - Only 36x36x13mm.
★ Weight - 23.3 grams and 2 layout boards
★ Professional - Symmetrical, Neat and Tidy and Easy to install in any racing drone
★ 36x36mm board with 30.5mm mounting holes
★ STM32F103CB CPU, 72Mhz inc FPU
★ High-Capacity Flash
★ use MPU6500 as accelerometer & gyro
★ MicroUSB socket
★ 1x 4pin JST-SH sockets (PPM, PWM, SERIAL RX, GPIO, ADC, 3V, 5V, GND)

www.exuavrc.com

★ The on-board pins are easily connected to our next 4 in 1 ESC &PDB board
★ Internal VTX (40CH) (25/200 / 400MW adjustable power video transmission)
★ 1x 4pin JST-SH sockets with BUZZER & WS2811 RGB LED
★ 1x 4pin JST-SH socket for SWD debugging
★ 1x 4pin JST-SH socket for Video & Audio transmission
★ 1 IPX sockets eeay connect the external antenna
★ 4x 3 Pad for motor output
★ 1x2 Pad for batter in easy solder

1, Cleanflight

https://github.com/Cleanflight

Betaflight

https://github.com/Betaflight

www.exuavrc.com

The hardware connection diagram

1,4 in 1 Board

2, FC board Top layer

www.exuavrc.com

3, FC Bottom layer