Page 1
MATERIAL SAFETY DATA SHEET
Extrudr DuraPro ASA
1.PRODUCT IDENTIFICATION
1.1 PRODUCT IDENTIFIER
TRADE NAME
Extrudr DuraPro ASA
1.2 MANUFACTURER
ADRESS
FD3D GmbH/Extrudr
Klosterstraße 13
A-6923 Lauterach
Österreich
EMAIL
2 HAZARD IDENTIFICATION
A. GHS Classification
Classification
B. GHS label elements
Hazard symbols
Signal words
Hazard statements
Precautionary statements
Not applicable
Not applicable
Not applicable
Not applicable
1. Prevention
Not applicable
2. Response
Not applicable
3. Storage
Not applicable
4. Disposal
Not applicable
C. Other hazards which do not result in classification : (NFPA Classification)
NFPA grade (0 ~ 4 level)
Health : 1, Flammability : 1, Reactivity : 0
3. COMPOSITION/INFORMATION ON INGREDIENTS
Chemical Name Trade names and Synonyms Content(%)
2-Propenoic acid butyl ester polymer with ethenylbenzene and 2-propenenitrile
typical stabilizers and lubricants typical stabilizers and lubricants 0-3
MATERIAL SAFETY DATA SHEET page 1 / 7
ASA 97~100
28/05/2019
Page 2
4. FIRST AID MEASURES
A. Eye contact
- Solid or dust may cause irritation or corneal injury due to mechanical action
- Immediately flush eyes with plenty of water for at least 15minutes and call a doctor.
B. Skin contact
- Essentially nonirritating to skin but rinse with copious water
- Mechanical injury only
C. Inhalation contact
- Dust may cause irritation to respiratory.
- In case of breathing, fumes released from heated material may cause respiratory
irritation.
· In case of inhaling dense smoke, immediately remove a person to fresh air.
may cause respiratory irritation
· If necessary, apply artificial respiration and seek medical attention immediately
D. Ingestion contact
- Unlikely due to physical state
- Rinse your mouth with water immediately.
- If vomiting occurs, lower the head to ease vomiting and seek for medical Advice.
E. Delayed and immediate effects and also chronic effects from short and long term exposure
- Not available
F. Notes to physician
- Not available
5. FIREFIGHTING MEASURES
A. Suitable (Unsuitable) extinguishing media
- Suitable extinguishing media: water, dry extinguishing media, foam, carbon dioxide
- Usually use water and use extinguishing media appropriate to surrounding conditions.
B. Specific hazards arising from the chemical
- Pyrolysate : carbon dioxide, carbon monoxide, hydrogen cyanide and a variety of
chemical substances
- The substances/groups of substances mentioned can be released in case of fire.
- Irritating gases and dense smoke
- Dust can form an explosive mixture with air
C. Special protective actions for firefighters
- Cool containers with water until well after fire is out.
- Keep unauthorized personnel out.
- Withdraw immediately in case of rising sound from venting safety devices or
discoloration of tank.
- Notify your local firestation and inform the location of the fire and characteristics
hazard.
- Wear appropriate protective equipment.
- Keep containers cool with water spray.
28/05/2019
MATERIAL SAFETY DATA SHEET page 2 / 7
Page 3
6. ACCIDENTAL RELEASE MEASURES
A. Personal precautions, protective equipment and emergency procedures
- Pellets or beads may present a slipping hazard.
- Sources of ignition should be kept well clear.
B. Environmental precautions
- Discharge into the environment must be avoided.
- Keep out of irrigation ditches, sewers, and water supplies.
- Spills should be collected to prevent contamination of waterways.
- If large amounts have been spilled, inform the relevant authorities.
C. Methods and materials for containment and cleaning up
- Sweep up.
- Appropriate container for disposal of spilled material collected.
- Avoid raising dust.
- Ensure adequate ventilation.
7. HANDLING AND STORAGE
A. Precautions for safe handling
- Avoid formation of dust.
- Avoid pellets / bags from getting wet.
- Keep bags always closed / Keep container lightly closed.
- When the product is ground (chopped), dust explosion regulations should be noted.
- Do not handle until all safety precautions have been read and understood
B. Conditions for safe storage, including any incompatibilities
- Protect against moisture. Keep sealed when not in use.
- Avoid extreme heat. Avoid all sources of ignition: heat, sparks, open flame.
- Please pay attention to incompatibilities materials and conditions to avoid.
- Keep bags / containers in a well-ventilated place
8. EXPOSURE CONTROLS/PERSONAL PROTECTION
A. Exposure limits
Hazard symbols
B. Engineering controls
- Good general ventilation should be sufficient for most conditions.
- Local exhaust ventilation may be necessary for some operations.
C. Personal protective equipment
Respiratory protection
Eye protection
Not applicable
- Consider warning properties before
- For most conditions, no respiratory protection should be needed ;
however, If handling at elevated temperatures without sufficient
ventilation, use an approved air-purifying respirator use.
- In dusty atmospheres, use an approved.
- Wear primary eye protection such as splash resistant safety
goggles with side-shields (frame goggles).
28/05/2019
MATERIAL SAFETY DATA SHEET page 3 / 7
Page 4
Hand protection
- Wear appropriate glove
Skin protection
- Wear appropriate clothing.
Others
- Not available
9. PHYSICAL AND CHEMICAL PROPERTIES
A. Color Not available
B. Odor Almost Odorless
C. Odor threshold Not available
D. pH Not available
E. Melting point/Freezing point 180~200℃ / Not available
F. Initial Boiling Point/Boiling Ranges Not available
G. Flash point Not available
H. Evaporation rate Not available
I. Flammability(solid, gas) Not available
J. Upper/Lower Flammability or explosive limits Not available
K. Vapour pressure Not available
L. Solubility Not available
M. Vapour density Not available
N. Specific gravity 1.07
O. Partition coefficient of n-octanol/water Not available
P. Autoignition temperature Not available
Q. Decomposition temperature Not available
R. Viscosity Not available
S. Molecular weight 50,000~250,000
10. STABILITY AND REACTIVITY
A. Chemical stability
- This material is stable under recommended storage and handling conditions.
- Hazardous Polymerization will not occur.
B. Possibility of hazardous reactions
- Avoid extreme heat. Avoid all sources of ignition: heat, sparks, open flame.
- Avoid fire and heating above 60℃ for storage conditions.
C. Conditions to avoid
- Avoid contact with incompatible materials and condition.
- Avoid : Accumulation of electrostatic charges, Heating, Flames and hot surfaces
D. Incompatible materials
- Strong oxidizing agents
B. Engineering controls
- May emit flammable vapour if involved in fire.
- Gaseous products of degradation can be given off if the product is greatly overheated.,
monomers, hydrocarbons, gases/vapours, cyclic low molecular weight oligomers, oxides
and hydrogen cyanide.
28/05/2019
MATERIAL SAFETY DATA SHEET page 4 / 7
Page 5
11. TOXICOLOGICAL INFORMATION
A. Information on the likely routes of exposure
Respiratory tracts
Oral
Not available
Not available
Eye - Skin
Not available
B. Delayed and immediate effects and also chronic effects from short and long term exposure
Acute toxicity
Oral
- [2-Propenoic acid butyl ester polymer with ethenylbenzene and
2-propenenitrile] : LD50 > 5000 ℃/℃ Rat
Dermal
Inhalation
Not available
Not available
Skin corrosion / irritation
Not available
Serious eye damage / irritation
Not available
Respiratory sensitization
Not available
Skin sensitization
Not available
Carcinogenicity
IARC
Not available
OSHA
Not available
ACGIH
Not available
Not available
NTP
EU CLP
Not available
12.ECOLOGICAL INFORMATION
A. Ecotoxcity
Fish
Not available
Crustaceans
B. Persistence and degradability
Persistence
Degradability
C. Bioaccumulative potential
Biocummulative potential
Biodegration
D. Mobility in soil
Mobility in soil
Algae
Not available
Not available
Not available
Not available
Not available
Not available
Not available
E. Other adverse effects
Other adverse effects
MATERIAL SAFETY DATA SHEET page 5 / 7
Not available
28/05/2019
Page 6
13. DISPOSAL CONSIDERATIONS
A. Disposal methods
- Must be dumped or incinerated in accordance with local regulations.
- For unused & uncontaminated product, the preferred options include sending to a
licensed, permitted: recycler, reclaim, incinerator or other thermal destruction device.
B. Special precautions for disposal
- Do not dump into any sewers, on the ground, or into any body of water. All disposal
methods must be in compliance with all Federal, State/Provincial and local laws and
regulations. Regulations may vary in different locations. Waste characterizations and
compliance with appliance laws are the responsibility solely of the waste generator.
14. TRANSPORT INFORMATION
A. UN number, (IMDG)
Not available
B. Proper shipping name
Not available
C. IMDG Class
Not available
D. IMDG Packing group
Not available
E. Marine pollutant
Not available
F. Special precautions for user related to transport or transportation measures
- Local transport follows in accordance with Dangerous goods Safety Management Law.
- Package and transport follow in accordance with Department of Transportation (DOT) and
other regulatory agency requirements.
- EmS FIRE SCHEDULE : Not available
- EmS SPILLAGE SCHEDULE : Not available
15. REGULATORY INFORMATION
A. National and/or international regulatory information
POPs Management Law
Not applicable
Information of EU Classification
Classification
Risk Phrases
Safety Phrase
Not applicable
Not applicable
Not applicable
U.S. Federal regulations
OSHA PROCESS SAFETY (29CFR1910.119)
CERCLA Section 103 (40CFR302.4)
EPCRA Section 302 (40CFR355.30)
EPCRA Section 304 (40CFR355.40)
EPCRA Section 313 (40CFR372.65)
MATERIAL SAFETY DATA SHEET page 6 / 7
Not applicable
Not applicable
Not applicable
Not applicable
Not applicable
28/05/2019
Page 7
Rotterdam Convention listed ingredients
Not applicable
Stockholm Convention listed ingredients
Not applicable
Montreal Protocol listed ingredients
Not applicable
16. OTHER INFORMATION
A. Reference
- The information contained herein is believed to be accurate. It is provided independently
of any sale of the product for purpose of hazard communication. It is not intended to
constitute performance information concerning the product. No express warranty, or
implied warranty of merchantability or fitness for a particular purpose is made with
respect to the product or the information contained herein.
- This Safety Data Sheet was compiled with data and information from the following
sources: KOSHA, NITE, ESIS, NLM, SIDS, IPCS
28/05/2019
MATERIAL SAFETY DATA SHEET page 7 / 7
Loading...