Extron Electronics USP 507 User Manual

Annotator and USP 507

Optional Output Boards • Installation Guide

C

VID

LO­RES

R-Y/

OUT

R

Y

Y/

B-Y/

G

B

The Extron Annotator and
USP 507 have a series of
optional output boards.

3G/HDSDI

OUT

These boards are:

• Scan converter board • 3G/HD-SDI board • DVI-D board •
Scaler board (with DVI-I). Any one of these boards mounts

DVI-D

OUT

in the optional output slot, above the RGB and MTP ports,

at the rear of the Annotator or USP 507.

For full device operating details, refer to either the

SCALED

DVI-I
OUT

Annotator User Guide or the USP 507 User Guide, both
available at www.extron.com.

Installing a Board in the Annotator or USP 507

1. Turn off the unit, and remove the power cord. Repeat for all connected devices.

2. Remove eight cover-securing screws from the top and three from each side. Slide

the top cover off. Retain the 14 screws.

3. At the rear optional output slot either:

a. Remove the two securing screws a from either side of the blank plate and lift

the plate away. Retain the screws.

NOTE: Re-use the screws to secure

the new output board in
place. Retain the blank plate.

Or,

b. If a board is already installed in the output slot, remove any cables and the two

screws a. Then remove the retaining screw that secures it to the post on the
device motherboard. Carefully lift the board away from the socket. Retain all
the screws.

4. Remove the new board from its box and anti-ESD bag,

holding the board by the front frame or board edge.

5. Turn the board over so the header sockets face up.

Insert the supplied connector pins into all sockets on
the board. Depending on the option card being
installed, the second header may not be present.

6. Turn the board over again so the connector pins are now

facing down. Carefully align the pins with the appropriate
sockets on the unit motherboard, and push the board rmly down into the sockets.

7. Secure the board to the frame with the two retaining screws

the motherboard using either the original or the supplied screw.

8. Replace the cover, securing it with the fourteen screws removed in step 2.

9. Reconnect any input and output devices and connect to the new board.

10. Connect any control devices.

11. Power on the Annotator or USP 507, and all the connected devices.

1 1

C

VID

LO­RES

R-Y/

OUT

R

RGB/R-Y,Y, B-Y

2

and to the post on

a

Y

Y/

B-Y/

G

B

MTP

1

Header Socket

Continued on side 2.

1

Annotator and USP 507

.

Optional Output Board • Installation Guide, (continued)

There are four ways to congure the boards: via front panel menus, a software program
(SPPCP), Simple Instruction Set (SIS™) commands, or internal web pages.

Configuring the Boards Using the Front Panel Menu System

To congure the 3G/HD-SDI and DVI-D boards using the front panel menu system, refer
to the relevant device user guide, available at www.extron.com.

The Annotator and the USP 507 have separate

front panel menus for conguring either the scan
converter board or the DVI-I scaler board.
This menu is accessible only after the board has

been installed.

Scan Converter Board and Scaler DVI-I Board
Configuration Menus

1. Press the Menu button repeatedly until either

the relevant Scan Converter Settings menu or
Aux Scaler Conguration menu appears.

2. Press the Next button to reach each

submenu as desired (see the images at right)
and use the front panel adjustment knobs
([ {) to change the settings.

Configuring the Boards Using the Signal
Processing Products Control Program

1. Open the Signal Processing Products

Control Program (SPPCP) on the PC that is
connected to the Annotator or USP 507
via a LAN or an RS-232 port.

2. Connect to the device. A new board relevant

tab (Scan Converter or AUX Scaler)
is now available. Click on the desired tab to

Aux Scaler

Configuration

Next

Resol 1024x768
Refresh 60.00Hz

Rotate to adjust
resolution. Rotate
to adjust refresh rate.

Next

Output Type

RGBHV

Rotate either to
select output type.

Next

Sync Po larity

H neg V neg

Rotate either to
adjust sync polarity
values.

Next

Aspect Ratio

Follow

Rotate either to
select aspect
ratio mode.

Next

Detail

64

Rotate either to
adjust detail level.

Next

Test Pattern

Crop

Rotate either to
select test pattern.

congure the settings.

Scan Converter

Settings

Next

H Size V

2048 2048

Rotate to adjust
H value. Rotate
to adjust V value.

Next

H Center V

2048 2048

Rotate to adjust
H value. Rotate
to adjust V value.

Next

Output Format
S-video/Comp

Rotate either to
select output format.

Next

Output Standard

NTSC

Rotate either to
select output
standard.

Next

Flicker Filter

3

Rotate either to
adjust flicker filter.

Next

H Filter

0

Rotate either to
adjust H filter.

Next

Encoder Filter

0

Rotate either to
adjust encoder filter

NOTE: 3G/HD-SDI and DVI-D output boards are buffered, so resolution and

refresh rates match all other outputs. The output rate must be set to
720p, 1080i, or 1080p to activate the 3G/HD-SDI output.

Refer to the SPPCP Help File for details.

Configuring the Boards Using Internal Web Pages

1. Using a LAN connection, open an Internet browser, enter the IP address of

the unit in the browser address bar, and connect to the unit.

2. Click on the Configuration tab and congure the settings as needed.

Configuring the Boards Using SIS Commands

The boards can also be congured with specic SIS commands. Refer to the Annotator
or USP 507 User Guide at www.extron.com for SIS command listings.

Extron USA Headquarters

+1.800.633.9876 (Inside USA/Canada Only)

© 2012 Extron Electronics — All rights reserved. All trademarks mentioned are the property of their respective owners. www.extron.com

2

Extron USA - West: +1.714.491.1500 FAX: [phone]
Extron USA - East: +1.919.863.1794 FAX: [phone]

68-1661-60 Rev C 04 12