Extron Electronics USFM 100 User Manual

USFM 100 Bracket Kit • Installation Guide

(1) 4-40 x 3/16" screw

The Extron® USFM 100 Bracket Kit consists of a single
mounting plate and three securing screws, and is used
for mounting an accessory device within the
USFM 100 Universal Short Throw Fixed Mount
enclosure. A single half rack device, or two quarter
rack devices, or two one-eighth rack devices can be
mounted on one plate, and up to four mounting
plates can be installed within a USFM 100 enclosure.

Installation

Figure 1. USFM 100 Bracket Kit Parts

NOTE: Ensure the finished installation is in accordance with local and national

building codes, fire and safety codes, UL requirements, and local and
national electrical codes.
See the USFM 100 User Guide for details on how to install the USFM 100.

(2) 4-40 x ¼" screws

Device Mounting Plate

1. If the USFM 100 is already installed,

remove the cover securing screws and
then remove the covers.

2. Place the bracket kit mounting plate

flat against the accessory device base
with the small securing tab over the
front panel (see figure 2).

3. Align the corresponding holes on the

plate with the two mounting holes in
the device base and secure the plate to
the device using the two 4-40 x ¼ inch
pan head screws (see figure 2).

NOTE: Quarter rack devices or

one-eighth rack devices can be
attached to the ends of the plate
as shown in figure 3.

4. Hook the tabs on the mounting plate

(now with the accessory device attached)
under the tabs on the USFM 100 base
plate (see figure 4).

Accessory
Device

(2) 4-40 x 1/4"
Screws

Figure 2. Attach the Plate to the Device

PEAKING

MTP SE RIE S

RGB

LEVEL

¼ Rack Device

Figure 3. Quarter Rack Device Attached

Mounting Plate

Tabs

NOTE: The mounting plate can be

installed in any available mounting
location (top or bottom) on the
USFM 100.

Device

Rear Panel

USFM 100 Base Plate
(Side View)

Figure 4. Hook the Plate under the Tabs

on the USFM 100.

Extron USA - West

Extron USA - East

Extron Europe

Extron Asia

Extron Japan

Extron China

Extron Middle East

USFM 100 Bracket Kit • Installation Guide, (Continued)

5. Secure the plate to the USFM 100

with the supplied screw through
the top plate tab (see figure 5).

NOTE: Use only the screw supplied

with the mounting plate to
avoid damaging the device.

4-40 x 3/16" screw

6. Cable and test the device as required.

7. Replace and secure the USFM 100

covers.

F

or configuration and operation, see the user

manual for the accessory device.

Optional Accessory
Device Mounted

Figure 5. Secure the Plate to the

USFM 100

Headquarters

+800.633.9876

Inside USA / Canada Only

+1.714.491.1500
+1.714.491.1517 FAX

Figure 6. The Finished Installation

+800.633.9876

Inside USA / Canada Only

+1.919.863.1794
+1.919.863.1797 FAX

©2010 Extron Electronics. All rights reserved. www.extron.com

+800.3987.6673

Inside Europe Only

+31.33.453.4040
+31.33.453.4 050 FAX

+800.7339.8766

Inside Asia Only

+65.6383.4400
+65.6383.4664 FAX

+81.3.3511.7655
+81.3.3511.7656 FAX

+400.883.1568

Inside China Only

+86.21.3760.1568
+86.21.3760.1566 FAX

+971.4.2991800
+971.4.2991880 FAX

68-1838-60

Rev A

12 10