Extron Electronics TP Receivers User Manual

Setup Guide — TP Receivers

5

Pin

1

2

3

6

7

8

4

Wire color

White-green

NOTE If using Enhanced

Skew-Free™ A/V cable, use th

e

TIA/EIA T568A standard only.

Green

White-orange

White-blue

Orange

White-brown

Brown

Wire color

T568A T568B

White-orange

Orange

White-green

White-blue

Green

White-brown

Brown

Side

Blue Blue

Insert
Twisted Pair
Wires

Pins:

12345678

RJ-45 Connector

C

For unbalanced audio, connect both sleeves to the center (ground

)

contact. DO NOT connect the sleeves to the negative (-) contacts.

Unbalanced Output

Balanced Output

Do not tin the wires!

Tip

Ring

Tip

Ring

L R

Sleeves

NO GROUND HERE

NO GROUND HERE

Tip

Tip

L R

Sleeves

RGB

J3

1

2

3

Component,
S-video,
Composite

J3

1

2

3

This card provides instructions for an experienced
installer to set up and operate the TP Receiver Series
products.
Refer to www.extron.com for the complete user’s
manual.

Pre-installation — Jumper settings

The TP R BNC A and TP R BNC AV are factory configured to receive
RGB video. They can receive component, S-video or composite video
by changing jumper J3 located on the main board.

If using the TP R BNC AV with an older TPX 88X transmitter,

N

Installation

Step 1 — Mounting

Turn off or disconnect all equipment power sources
and mount the receiver as required.

Step 2 — Connect input

Connect the RJ-45 cable (from a TP transmitter)
to the Input port on the TP R.
Terminate the ends of the cable to the same
standards.

Step 3 — Connect outputs

Attach the applicable output cables (video, audio),
depending on the TP R model.

a. Composite video output connector — Connect to the single female BNC

b. S-video output connector — Connect to the R (C-chroma) and G (Y-luma)

c. Component video — Connect to the R (R-Y), G (Y) and B (B-Y) connectors.
d. RGBHV Video — Connect to the R, G, B, H, V connectors.

e. RGBS video — Connect to the R, G, B, H/V connectors.

f. High resolution video output connector — Connect to the 15-pin HD

g. Audio connector — Connect an audio device accepting line level analog

download the TP Receivers User’s Manual at www.extron.com
and refer to the audio jumper settings.

connector (VIDEO) for composite video output (TP R BNC AV Only) or to
either the R, or G, or B connectors (TP R BNC A Only).

connectors.

connector (TP R 15HD A only).

audio to the unbalanced stereo audio RCA connectors (TP R BNC A and
TP R BNC AV) or to the line level stereo 3.5 mm, 5-pole captive screw
connectors as shown.

Continued on other side

Extron USA - West

Headquarters

+800.633.9876

Inside USA / Canada Only

+1.714.491.1500
+1.714.491.1517 FAX

Extron USA - East

+800.633.9876

Inside USA / Canada Only

+1.919.863.1794
+1.919.863.1797 FAX

Extron Europe

+800.3987.6673

Inside Europe Only

+31.33.453.4040
+31.33.453.4050 FA X

Extron Asia

+800.7339.8766

Inside Asia Only

+65.6383.4400
+65.6383.4664 FAX

Extron Japan

+81.3.3511.7655
+81.3.3511.7656 FAX

Extron China

+400.883.1568

Inside China Only

+86.21.3760.1568
+86.21.3760.1566 FAX

Extron Middle East

+971.4.2991800
+971.4.2991880 FAX

Setup Guide — TP Receivers, cont’d

SECTION A–A

Power Supply

Output Cord

Ridges

Smooth

A A

TP R 15HD A

3/16”

(5 mm)

Max.

TP R BNC A

N/C N/C

TP R BNC AV

VIDEO

MANUAL

AUTO

LEVEL PEAKING

RGB

MANUAL

AUTO

LEVEL PEAKING

C SYNC

SOG

C VIDEO

N/C

ON

SOG

C SYNC

TP T 15HD A

TP R BNC A

TP T 15HD A

H-SHIFT

BUFFEREDCOMPUTER

INPUT

AUDIO

ID PIN 4

ID PIN 11

LOCAL MONITOR

PC

CAT 5 UTP Cable

Audio

Projector

RGB INPUT

RGB OUTPUT

R G

B H/HV V

A

AUDIO

L

R

B

SOG

C SYNC

POWER

15V .5A DC

L

R

Step 4 — Power

Plug the included external power supply
into the 2-pole (TP R 15HD A) or 3-pole
(TP R BNC A) captive screw connector. Wire
the connector as shown and plug it into the
receiver. The front panel Power LED is amber
when power is present and green when signal
and power are present.

Step 5 — Set Rear Panel DIP Switches

2-position (TP R BNC A/AV), or 4-position (TP R 15HD A) switch (up = ON)
a. SOG — Sync on Green. Set this switch up for RGsB and down for RGBHV or

RGBS video.

b. C Sync — Set this switch up for RGBS and down for RGBHV or RGsB video.
c. C video (TP R 15HD A only) — Set this switch down (off) for RGB video or up

(on) for component/S-video/composite video.

d. N/C (TP R 15HD A only) — Not used.

Step 6 — Manual/Auto Switch

N There are 2 sets of switches and controls (Video and RGB) on TP R BNC AV only.

Auto provides automatic signal level and peaking
compensation of the output for long cable runs.

Step 7 — Peaking and Level Adjustments

Manual compensation for long cable runs can be made by the user
with the Auto/Manual switch in the Manual position.

Image sharpness is adjusted with the Peaking Control. Increased peaking compensates
for mid- and high-frequency detail loss. Minimum setting (full counterclockwise) is zero
peaking.

Image brightness is adjusted using the Level Control which increases the video signal
output voltage to boost brightness.

While viewing the display, adjust either or both controls for the best image quality.

Typical TP R application

68-547-50

Rev. A

01 09