Page 1
Product Category
complete user guide and installation
instructions befor
oduct to the power sou
IMPORTANT:
TLP Pro 1220TG and TLP Pro 1520TG • Setup Guide
Go to www.extron.com for the
pr
e connecting the
Overview
The Extron TLP Pro 1220TG is a 12.1 inch tabletop touchpanel with a high resolution 1280x800 capacitive touch screen. The
TLP Pro 1520TG is a 15.6 inch tabletop touchpanel with a high resolution 1366x768 capacitive touch screen. They are ideal for any
AV applications requiring large touchpanels with exible mounting options and fully customizable interfaces. This guide provides
instructions for experienced installers to mount and install a TLPPro 1220TG or TLP Pro 1520TG touchpanel. For more complete
instructions, see the TLPPro 1220 Series and TLPPro 1520 Series User Guide at www.extron.com.
Setup Checklist
Get Ready
Download and install the latest version of the following software:
GUI Designer — for designing layouts for Extron TouchLink® Pro touchpanels and third party touch interfaces.
Global Configurator® Plus and Professional — for setting up and conguring the control processor and touchpanel.
Toolbelt — provides device discovery, device information, rmware updates, and conguration of network settings, system
utilities, and user management for TouchLink Pro devices.
All three software programs are available from www.extron.com.
Obtain the following network information from your network administrator:
DHCP status (on or off). If DHCP is off, you will also require
rce.
IP address Subnet mask Gateway
User name — by default these are either admin or user.
Passwords — by default these are either extron (for admin) or the eld is left blank (for user).
Make a note of the touchpanel MAC address.
Mount and Cable All Devices
ATTENTION:
• Do not power on the touchpanels or control processors until you have read the Attention in the Power Supply section of
the TLP Pro 1220 Series and TLP Pro 1520 Series User Guide or the IPL Pro User Guide.
• Ne branchez pas les écrans tactiles ou les contrôleurs avant d’avoir lu la mise en garde dans la section «sources
d’alimentation» du TLP Pro 1220 Series and TLP Pro 1520 Series UserGuide ou du IPLProUserGuide.
Mount the units. There are several mounting options for TouchLink Pro touchpanels (see Mounting on the following page).
Connect cables to the touchpanels. To connect cables, remove the back and base covers (see figure 3). For more information
about the cable connectors, see Rear Panel Features on page 3.
Connect the power cords and power on all devices.
Set up the Touchpanels for Network Communication
Connect the PC that you will use for setup, the control processor, and touchpanel to the same Ethernet subnetwork.
Use the Setup Menu (see page 4) or Toolbelt to set the DHCP status and, if necessary, the IP address, subnet mask, gateway,
and related settings for the touchpanel.
Configure the Touchpanels
The GUI Designer Help File, Global Configurator Help File, and the Toolbelt Help File provide step‑by‑step instructions and more
detailed information. The Global Configurator Help File includes an introduction to the software and sections on how to start a
project and conguration.
1
Page 2
TLP Pro 1220TG and TLP Pro 1520TG • Setup Guide (Continued)
Base Cover (2)
ve
Kensington Security Slot
Mounting holes
Mounting
The TLP Pro 1220TG and TLP Pro 1520TG come assembled with stands that allow the units to be placed on any suitable surface.
A range of optional mounting kits are available for both the TLP Pro 1220TG and the TLP Pro 1520TG. The kits must be purchased
separately. Follow the installation instructions provided with the kit.
Securing the Touchpanel with Screws
The bases of the units also have two mounting holes that allow the
units to be secured to the desktop. Figure 1 shows the base of the
TLPPro1520TG, but the TLP Pro 1220TG is very similar.
1. Mark the location of two holes, 4.96inches (126 mm) apart.
This dimension is the same for both the TLP Pro 1220TG and
the TLPPro1520TG.
2. Drill two holes through the desktop from underneath.
3. Attach the touchpanel, using two #8 wood screws through
the desktop from underneath into the two holes in the base.
Kensington® Security Lock
For added security, attach a Kensington Security Lock (not
provided) to the metal‑reinforced slot on the rear edge of the
base. Figure 2 shows the rear edge of the TLP Pro 1520TG
base, but the TLP Pro 1220TG base is very similar.
Follow the instructions that are provided by the
manufacturer to install the lock.
Figure 1. Mounting Holes in TLP Pro 1520TG Base
Figure 2. Slot for Kensington Security Lock
SMA-1 Swivel Mount Adapter
Both touchpanels can also be mounted with the optional Extron SMA‑1 swivel mount adapter, which allows them to be mounted
permanently and swivel up to 180° in either direction.
Figure 3. Remove the Back and Base Covers
1. Remove the back cover and base cover, using the provided Extron removal tool. There is one notch on each side of the back
Notches to Remo
Back Cover (2)
Notch to Remove
cover and two notches on the back edge of the base cover. You must remove the back cover before you can remove the base
cover.
2. Attach the conduit, insulation disk, and swivel disk and congure the set screws to allow for the degree of swivel that is required
(see the SMA-1 Swivel Mount Adapter Kit User Guide, available at www.extron.com).
3. Place the mounting hole in the base over the conduit of the SMA‑1.
4. Secure the unit with the backing plate and locking nut as described in the SMA-1 Swivel Mount Adapter Kit User Guide.
VESA mounting
These touchpanels can be VESA mounted, using any third‑party D‑type VESA mounting kit with the 100 x 100 mm mounting pattern.
1. Remove the back panel.
2. Remove the four screws holding the touchpanel to the base. There are two screws in each base attachment hinge
(figure 5, K).
3. Follow the instructions provided with the VESA mounting kit.
2
Page 3
Product Category
AB
BC
TLP Pro 1220TG
TLP Pro 1520 TG
Front Panel Features
The front panel diagrams for these two products are shown below. They are not to the same scale.
AAA
BB
D
D
EEE
E
F
F
Figure 4. TLP Pro 1220TG (left) and TLP Pro 1520TG (right) Front Panels
Communication LED — shows the conguration and connection status of the touchpanel:
A
z Unlit during normal operation (the touchpanel is congured and connected to an IP Link Pro control processor).
z Blinks red if the touchpanel has been congured but is not connected to an IP Link Pro control processor.
z Lights red permanently if the touchpanel has not been congured.
Status light — one LED light bar, above the screen, which can be programmed to provide system feedback.
B
Ambient light sensor — monitors ambient light level and adjusts screen brightness.
C
Capacitive touch screen — the TLP Pro 1220TG has a 12.1 inch screen with a 1280x800 resolution. The TLP Pro 1520TG has
D
a 15.6 inch screen with 1366x768 resolution.
Speakers — located below the screen, one on each side of the panel. These speakers provide stereo audio for video preview
E
and audible feedback from button presses.
Motion sensor — detects motion in front of the touchpanel.
F
F
F
CCC
EEE
E
E
E
Rear Panel Features
The rear panel diagrams for these two products (with backs removed) are shown below. They are not to the same scale.
B
BFFEEDDAA
G
G
H
H
BBFFEEDDAACCCC
II
J
J
KK
Figure 5. TLP Pro 1220TG (left) and TLP Pro 1520TG (right) Rear Panels
Power supply input
A
USB connectors (2)
B
Rear status light
C
HDMI input
D
See the following page for a description of these features.
XTP/LAN/PoE input
E
Audio output
F
Menu button
G
Reset button
H
Reset LED
I
VESA mounting holes (4)
J
Base attachment hinge (2)
K
3
Page 4
TLP Pro 1220TG and TLP Pro 1520TG • Setup Guide (Continued)
XTP Device
touchpanel
Extr
Power supply input (see figure 5) — connect a 12 VDC, 3.0 A power supply (not provided) to this DC plug connector.
A
ATTENTION:
• The touchpanels can use a 12 VDC desktop power supply and are also Power over Ethernet (PoE Plus IEEE
802.3at) compliant. Do not connect either power supply before reading the Attention in the Power section of the
TLP Pro 1220 Series and TLP Pro 1520 Series User Guide.
• Les écrans tactiles peuvent utiliser une source d’alimentation externe 12 Vcc, et sont également compatible avec
l’alimentation POE via Ethernet (PoE Plus IEEE 802.3at). Ne branchez pas de sources d’alimentation externes avant
d’avoir lu les mises en garde dans la section «PowerSupply» du TLP Pro 1220 Series and TLPPro 1520 Series
User Guide.
NOTE: The TLP Pro 1220TG and TLP Pro 1520TG are shipped without a power supply. Either the 12 VDC, 3.0 A power
supply or the power injector must be purchased separately.
USB connectors (see figure 5) — for peripheral controls.
B
Rear status light (see figure 5) — an LED light bar that can be programmed to provide system feedback.
C
HDMI input (see figure 5) — for alternative video input.
D
XTP/LAN/PoE input (see figure 5) — is in the top of the recessed area.
E
F
G
H
I
J
K
XTP input — Connect the touchpanel to the XTP source using a twisted pair cable,
terminated with an RJ‑45 connector.
LAN input — Connect the touchpanel to the LAN using a twisted pair cable,
terminated with an RJ‑45 connector.
PoE input — the connector can be used with a PoE plus power injector (not
provided). Connect the cables as shown in the gure to the right, which shows the
Extron PI 140 power injector (recommended by Extron).
An Extron IP Link Pro control processor must also be connected to the same network as the TouchLink Pro touchpanel.
Audio output (see figure 5) — for use with headphones or assistive listening devices.
Menu button (see figure 5) — activates the setup menu and calibration screen (see below).
Reset button (see figure 5) — pressing the reset button allows the unit to be reset in any of three different modes. For full
information about the modes, see the TLPPro 1220 Series and TLPPro 1520 Series User Guide.
Reset LED (see figure 5) — provides feedback about the reset status when the user presses the reset button.
VESA mounting holes (4) (see figure 5) — for use with D‑type VESA mounting kits with the 100 x 100 mm mounting pattern.
Base attachment hinge (2) (see figure 5) — each hinge secures the touchpanel to the base with two screws.
100-240V~50/60 Hz
1.1A MAX
on PI 140
To Network or
INPUT OUTPUT
POWERED TLP
LAN
To a TLP Pro
Reset Modes: a Brief Summary
The TLP Pro 1220TG and TLP Pro 1520TG offer the following reset modes:
• Use factory firmware:
Press and hold the Reset button (figure 5, H) while applying power to the unit. Use this mode
to replace rmware in the event of rmware failure.
• Reset All IP Settings:
Press and hold the Reset button for 6 seconds. After the Reset LED (figure5,I) ashes
twice, release and momentarily press the Reset button. Use this mode to reset all network
settings without affecting user‑loaded les.
• Reset to Factory Defaults:
Press and hold the Reset button for 9 seconds. After the Reset LED ashes three times,
release and momentarily press the Reset button. Use this mode to return the interface to
factory default settings.
Setup Menu
Press the menu button (figure 5, G) to open the setup menu. Select any
of the ve available screens (Status, Network, Display, Audio, Input and
Advanced) by pressing the appropriate button in the navigation bar at the
top of the screen (for more information, see the TLPPro 1220 Series and
TLP Pro 1520 Series User Guide).
Figure 6 shows the setup menu for the TLP Pro 1220TG. The setup menu
for the TLP Pro 1520TG is identical.
Press the menu button for at least 3 seconds to open the calibration
screen. Follow the on‑screen instructions.
Extron Headquarters
+1.800.633.9876 (Inside USA/Canada Only)
Extron USA - West Extron USA - East
+1.714.491.1500 +1.919.850.1000
+1.714.491.1517 FAX +1.919.850.1001 FAX
© 2015 Extron Electronics All rights reserved. All trademarks mentioned are the property of their respective owners. www.extron.com
4
Extron Europe
+800.3987.6673
(Inside Europe Only)
+31.33.453.4040
+31.33.453.4050 FAX
Extron Asia
+65.6383.4400
+65.6383.4664 FAX
Extron Japan
+81.3.3511.7655
+81.3.3511.7656 FAX
Status
Network
Info
Model: TLP Pro 1220TG
Part Number:60-1341-02
Firmware
Version:
Bootloader
Version:
PoE: Active
1.02.0000.b003
1.03.0000
Display
IP Address:
DHCP:
Host Name:
Master Volume:
Master Mute: Off
Controller IP: 192.168.254.250
Project Size: 1/197 MB
Audio
Network
192.168.254.251
Off
TLI-AB-CD-EF
Audio
100
Advanced
Advanced
Input
Resolution:
Project:
Sleep Timer:
Input
HDMI: No Signal
XTP: 1280x720
Display
1280x800
1280x800
5 Minutes
Exit
HDCP
Figure 6. Setup Menu: Status page for TLP Pro 1220TG
Extron China
+86.21.3760.1568
+86.21.3760.1566 FAX
Extron Middle East
+971.4.299.1800
+971.4.299.1880 FAX
Extron Korea
+82.2.3444.1571
+82.2.3444.1575 FAX
Extron India
1800.3070.3777
(Inside India Only)
+91.80.3055.3777
+91.80.3055.3737 FAX
68-2294-50 Rev. A
08 15
Loading...