Extron Electronics TLM 700 User Manual

Extron TLM 700 Bezel Replacement Kits

Extron® provides replacement bezel kits for the TLP 700 TouchLink™
panels. These bezels are available in white or black finishes for the
TLP 700MV and in black only for the TLP 700TV.

Each kit contains four bezels:

Description Part Number

TLM 700M black bezel kit 70-723-02

TLM 700M white bezel kit 70-723-03

TLM 700T black bezel kit 70-724-02

A. With buttons and an encoder knob (identical to the original bezel)

B. Without buttons but with an encoder knob.

C. With buttons but without an encoder knob.

D. Without buttons and without an encoder knob.

This guide provides instructions for removing the existing bezel and fitting the replacement.

Replacing the Bezel on the TLP 700MV

Determine which of the four bezels contained in each kit (shown below) will be fitted and follow the steps described in the
figure:

A. With buttons

With encoder knob

follow steps

1 and 4

B. Without buttons

With encoder knob

follow steps

1, 2, and 4

C. With buttons

Without encoder knob

follow steps

1, 3, and 4

D. Without buttons

Without encoder knob

follow steps

1 through 4

1. Gently lift the bezel away from the unit, starting at
the corners. It is held by clips on each side.

Remove all ten lenses
and diffusers.

Diffuser

Clear Lens

Remove encoder knob.

3. To remove the encoder knob, grasp it and
pull it away from the unit (see figure above).

4. Select the appropriate bezel and snap it into place
(see figure at right). Ensure the corners are securely
in place.

Bezel attaches to unit at
(4) places each side.

2. To remove all ten buttons, grasp the lenses

and diffusers from each of the ten buttons and pull
them away from the unit (see figure at left).

If necessary, use a flat bladed screwdriver (provided)

and gently pry the diffuser away from the unit.

Bezel attaches to unit at
(4) places each side.

Extron TLM 700 Bezel Replacement Kits, cont'd

Extron USA - West

Headquarte rs

+80 0.63 3.98 76

Inside USA / Canada Only

+1.714.491.1500
+1.714.491.1517 FAX

Extron USA - East

+80 0.63 3.98 76

Inside USA / Canada Only

+1.919.863.1794
+1.919.863.1797 FA X

Extron Europe

+80 0.39 87.6673

Inside Europe Only

+31.33. 453 .40 40
+31.33. 453 .40 50 FA X

Extron Asia

+80 0.733 9.876 6

Inside Asia Only

+65.6 38 3.44 00
+65.6 38 3.46 64 FA X

Extron Japan

+81.3.3 511.7655
+81.3.3 511.7656 FA X

Extron China

+40 0.88 3.1568

Inside China Only

+86. 21.376 0.1568
+86. 21.376 0.1566 FA X

Extron Middle East

+971.4. 299 1800
+971.4. 299 1880 FA X

el.

Remove (3) screws.

Replacing the Bezel on the TLP 700TV

Determine which of the four bezels contained in each kit (shown below) will be fitted and follow the steps described in the
figure:

A. With buttons

With encoder knob

follow steps

1, 2, 3, 6, and 7

B. Without buttons

With encoder knob

follow steps

1, 2, 3, 4, 6, and 7

1. Check the "E" number on the label on the base of the unit.
It appears twice (see figure at right). In the example
shown, the number is E21577.

• If the number is E21577 or higher, you will only

need to remove five screws in step 2.

• If the number is lower than E21577, you will need to

remove a sixth screw.

If necessary,
remove 6th screw.

Remove (2) screws.

3. Remove the existing bezel (see figure at right). It is held
in place by one tab on each side. Squeeze the panel on
both sides and pull the bezel away from the unit.

C. With buttons

Without encoder knob

follow steps

1, 2, 3, 5, 6, and 7

S/N E21577 D04937 WO 1675379-65
TLP 700TV

MAC: 00-05-

S/N: E21577 D04937

D. Without buttons

Without encoder knob

follow all steps

1 through 7

2. To remove the existing bezel, first remove the five
screws from the back panel (see figure at left).

If necessary (see step 1) remove the sixth screw. The
screw is obstructed by the stand and removing it
requires a right angle screw driver or a short Philips
head bit.

Squeeze the

Bezel held in
place by tabs,
(1) on each side.

unit on each
side.

5. To remove the encoder knob grasp it and pull it

6. Select the appropriate bezel and snap it into place

7. Insert the five screws removed in step 2. If a sixth screw

Remove buttons.

Remove encoder
knob.

away from the unit (see figure above).

(see figure at right). Ensure the corners are securely in
place.

was removed, it does not need to be replaced.

© 2010 Extron Electronics. All rights reserved.

4. To

remove all ten buttons, grasp the rubber

strips and pull them away from the unit. Five buttons
on each side are arranged on a strip so that all five can
be removed at once (see figure at left).

Snap in new bez

68-1831-01

Rev. A

03 10