Page 1
User’s Guide
68-1259-01
Rev. B
01 07
PVT CV D, PVT RBG D,
PVT CV AAP, and PVT RGB AAP
PoleVault™ Twisted Pair Transmitters
(Decora® and AAP Models)
im Vertrieb von
CAMBOARD Electronics
www.camboard.de
Tel. 07131 911201
Fax 07131 911203
ce-info@camboard.de
Page 2
Precautions
This symbol is intended to alert the user of important
operating and maintenance (servicing) instructions in
the literature provided with the equipment.
This symbol is intended to alert the user of the
presence of uninsulated dangerous voltage within
the product’s enclosure that may present a risk of
electric shock.
Caution
Read Instructions • Read and understand all safety and operating
instructions before using the equipment.
Retain Instructions • The safety instructions should be kept for future
reference.
Follow Warnings • Follow all warnings and instructions marked on the
equipment or in the user information.
Avoid Attachments • Do not use tools or attachments that are not
recommended by the equipment manufacturer because they may be
hazardous.
Warning
Power sources • This equipment should be operated only from the power source
indicated on the product. This equipment is intended to be used with a main power
system with a grounded (neutral) conductor. The third (grounding) pin is a safety
feature, do not attempt to bypass or disable it.
Power disconnection • To remove power from the equipment safely, remove all power
cords from the rear of the equipment, or the desktop power module (if detachable),
or from the power source receptacle (wall plug).
Power cord protection • Power cords should be routed so that they are not likely to be
stepped on or pinched by items placed upon or against them.
Servicing • Refer all servicing to qualified service personnel. There are no user-
serviceable parts inside. To prevent the risk of shock, do not attempt to service
this equipment yourself because opening or removing covers may expose you to
dangerous voltage or other hazards.
Slots and openings • If the equipment has slots or holes in the enclosure, these are
provided to prevent overheating of sensitive components inside. These openings
must never be blocked by other objects.
Lithium battery • There is a danger of explosion if battery is incorrectly
replaced. Replace it only with the same or equivalent type recommended by
the manufacturer. Dispose of used batteries according to the manufacturer ’s
instructions.
Ce symbole sert à avertir l’utilisateur que la
documentation fournie avec le matériel contient des
instructions importantes concernant l’exploitation et
la maintenance (réparation).
Ce symbole sert à avertir l’utilisateur de la présence
dans le boîtier de l’appareil de tensions dangereuses
non isolées posant des risques d’électrocution.
Attention
Lire les instructions• Prendre connaissance de toutes les consignes de
sécurité et d’exploitation avant d’utiliser le matériel.
Conserver les instructions• Ranger les consignes de sécurité afin de pouvoir
les consulter à l’avenir.
Respecter les avertissements • Observer tous les avertissements et consignes
marqués sur le matériel ou présentés dans la documentation utilisateur.
Eviter les pièces de fixation • Ne pas utiliser de pièces de fixation ni d’outils
non recommandés par le fabricant du matériel car cela risquerait de poser
certains dangers.
Avertissement
Alimentations• Ne faire fonctionner ce matériel qu’avec la source d’alimentation
indiquée sur l’appareil. Ce matériel doit être utilisé avec une alimentation principale
comportant un fil de terre (neutre). Le troisième contact (de mise à la terre) constitue
un dispositif de sécurité : n’essayez pas de la contourner ni de la désactiver.
Déconnexion de l’alimentation• Pour mettre le matériel hors tension sans danger,
déconnectez tous les cordons d’alimentation de l’arrière de l’appareil ou du module
d’alimentation de bureau (s’il est amovible) ou encore de la prise secteur.
Protection du cordon d’alimentation • Acheminer les cordons d’alimentation de
manière à ce que personne ne risque de marcher dessus et à ce qu’ils ne soient pas
écrasés ou pincés par des objets.
Réparation-maintenance • Faire exécuter toutes les interventions de réparation-
maintenance par un technicien qualifié. Aucun des éléments internes ne peut être
réparé par l’utilisateur. Afin d’éviter tout danger d’électrocution, l’utilisateur ne doit
pas essayer de procéder lui-même à ces opérations car l’ouverture ou le retrait des
couvercles risquent de l’exposer à de hautes tensions et autres dangers.
Fentes et orifices • Si le boîtier de l’appareil comporte des fentes ou des orifices, ceux-ci
servent à empêcher les composants internes sensibles de surchauffer. Ces ouvertures
ne doivent jamais être bloquées par des objets.
Lithium Batterie • Il a danger d’explosion s’ll y a remplacment incorrect de la batterie.
Remplacer uniquement avec une batterie du meme type ou d’un ype equivalent
recommande par le constructeur. Mettre au reut les batteries usagees conformement
aux instructions du fabricant.
Safety Instructions • English
Consignes de Sécurité • Français
Sicherheitsanleitungen • Deutsch
Dieses Symbol soll dem Benutzer in der im
Li efe rum fan g en tha lte nen D oku men tation
besonders wichtige Hinweise zur Bedienung und
Wartung (Instandhaltung) geben.
Dieses Symbol soll den Benutzer darauf aufmerksam
machen, daß im Inneren des Gehäuses dieses
Produktes gefährliche Spannungen, die nicht isoliert
sind und die einen elektrischen Schock verursachen
können, herrschen.
Achtung
Lesen der Anleitungen • Bevor Sie das Gerät zum ersten Mal verwenden,
sollten Sie alle Sicherheits-und Bedienungsanleitungen genau durchlesen
und verstehen.
Aufbewahren der Anleitungen • Die Hinweise zur elektrischen Sicherheit
des Produktes sollten Sie aufbewahren, damit Sie im Bedarfsfall darauf
zurückgreifen können.
Befolgen der Warnhinweise • Befolgen Sie alle Warnhinweise und
Anleitungen auf dem Gerät oder in der Benutzerdokumentation.
Keine Zusatzgeräte • Verwenden Sie keine Werkzeuge oder Zusatzgeräte,
die nicht ausdrücklich vom Hersteller empfohlen wurden, da diese eine
Gefahrenquelle darstellen können.
Vorsicht
Stromquellen • Dieses Gerät sollte nur über die auf dem Produkt angegebene
Stromquelle betrieben werden. Dieses Gerät wurde für eine Verwendung mit einer
Hauptstromleitung mit einem geerdeten (neutralen) Leiter konzipiert. Der dritte
Kontakt ist für einen Erdanschluß, und stellt eine Sicherheitsfunktion dar. Diese
sollte nicht umgangen oder außer Betrieb gesetzt werden.
Stromunterbrechung • Um das Gerät auf sichere Weise vom Netz zu trennen, sollten
Sie alle Netzkabel aus der Rückseite des Gerätes, aus der externen Stomversorgung
(falls dies möglich ist) oder aus der Wandsteckdose ziehen.
Schutz des Netzkabels • Netzkabel sollten stets so verlegt werden, daß sie nicht im
Weg liegen und niemand darauf treten kann oder Objekte darauf- oder unmittelbar
dagegengestellt werden können.
Wartung • Alle Wartungsmaßnahmen sollten nur von qualifiziertem Servicepersonal
durchgeführt werden. Die internen Komponenten des Gerätes sind wartungsfrei.
Zur Vermeidung eines elektrischen Schocks versuchen Sie in keinem Fall, dieses
Gerät selbst öffnen, da beim Entfernen der Abdeckungen die Gefahr eines
elektrischen Schlags und/oder andere Gefahren bestehen.
Schlitze und Öffnungen • Wenn das Gerät Schlitze oder Löcher im Gehäuse aufweist,
dienen diese zur Vermeidung einer Überhitzung der empfindlichen Teile im
Inneren. Diese Öffnungen dürfen niemals von anderen Objekten blockiert werden.
Litium-Batterie • Explosionsgefahr, falls die Batterie nicht richtig ersetzt
wird. Ersetzen Sie verbrauchte Batterien nur durch den gleichen oder einen
vergleichbaren Batterietyp, der auch vom Hersteller empfohlen wird. Entsorgen Sie
verbrauchte Batterien bitte gemäß den Herstelleranweisungen.
Este símbolo se utiliza para advertir al usuario
sobre instrucciones importantes de operación y
mantenimiento (o cambio de partes) que se desean
destacar en el contenido de la documentación
suministrada con los equipos.
Este símbolo se utiliza para advertir al usuario sobre
la presencia de elementos con voltaje peligroso sin
protección aislante, que puedan encontrarse dentro
de la caja o alojamiento del producto, y que puedan
representar riesgo de electrocución.
Precaucion
Leer las instrucciones • Leer y analizar todas las instrucciones de operación y
seguridad, antes de usar el equipo.
Conservar las instrucciones • Conservar las instrucciones de seguridad para
futura consulta.
Obedecer las advertencias • Todas las advertencias e instrucciones marcadas
en el equipo o en la documentación del usuario, deben ser obedecidas.
Evitar el uso de accesorios • No usar herramientas o accesorios que no
sean especificamente recomendados por el fabricante, ya que podrian
implicar riesgos.
Advertencia
Alimentación eléctrica • Este equipo debe conectarse únicamente a la fuente/tipo
de alimentación eléctrica indicada en el mismo. La alimentación eléctrica de este
equipo debe provenir de un sistema de distribución general con conductor neutro
a tierra. La tercera pata (puesta a tierra) es una medida de seguridad, no puentearia
ni eliminaria.
Desconexión de alimentación eléctrica • Para desconectar con seguridad la acometida
de alimentación eléctrica al equipo, desenchufar todos los cables de alimentación
en el panel trasero del equipo, o desenchufar el módulo de alimentación (si fuera
independiente), o desenchufar el cable del receptáculo de la pared.
Protección del cables de alimentación • Los cables de alimentación eléctrica se deben
instalar en lugares donde no sean pisados ni apretados por objetos que se puedan
apoyar sobre ellos.
Reparaciones/mantenimiento • Solicitar siempre los servicios técnicos de personal
calificado. En el interior no hay partes a las que el usuario deba acceder. Para evitar
riesgo de electrocución, no intentar personalmente la reparación/mantenimiento
de este equipo, ya que al abrir o extraer las tapas puede quedar expuesto a voltajes
peligrosos u otros riesgos.
Ranuras y aberturas • Si el equipo posee ranuras o orificios en su caja/alojamiento,
es para evitar el sobrecalientamiento de componentes internos sensibles. Estas
aberturas nunca se deben obstruir con otros objetos.
Batería de litio • Existe riesgo de explosión si esta batería se coloca en la posición
incorrecta. Cambiar esta batería únicamente con el mismo tipo (o su equivalente)
recomendado por el fabricante. Desachar las baterías usadas siguiendo las
instrucciones del fabricante.
Instrucciones de seguridad • Español
Precautions
ᅝܼ乏ⶹ噝Ё᭛
䖭Ͼヺোᦤ⼎⫼᠋䆹䆒⫼᠋ݠЁ
ⱘ᪡㓈ᡸ䇈ᯢDŽ
䖭Ͼヺো䄺⫼᠋䆹䆒ᴎݙᲈ
䴆ⱘ䰽⬉ˈ᳝㾺⬉䰽DŽ
⊼ᛣ
䯙䇏䇈ᯢк噝⫼᠋Փ⫼䆹䆒ࠡᖙ乏䯙䇏ᑊ⧚㾷
᳝ᅝܼՓ⫼䇈ᯢDŽ
ֱᄬ䇈ᯢк噝⫼᠋ᑨֱᄬᅝܼ䇈ᯢкҹᇚᴹՓ⫼DŽ
䙉ᅜ䄺噝⫼᠋ᑨ䙉ᅜѻક⫼᠋ᣛϞⱘ᠔᳝
ᅝܼ᪡䇈ᯢDŽ
䙓ܡ䗑ࡴ噝ϡ㽕Փ⫼䆹ѻકଚ≵᳝㤤ⱘᎹ
䗑ࡴ䆒ˈҹ䙓ܡ䰽DŽ
䄺
⬉⑤噝䆹䆒া㛑Փ⫼ѻકϞᯢⱘ⬉⑤DŽ䆒ᖙ⫼᳝
ഄ㒓կ⬉㋏㒳կ⬉DŽϝᴵ㒓˄ഄ㒓˅ᰃᅝ䆒ᮑˈϡ㛑ϡ
⫼䏇䖛DŽ
ᢨᥝ⬉⑤噝ЎᅝܼഄҢ䆒ᢨᥝ⬉⑤ˈ䇋ᢨᥝ᠔᳝
ৢḠ䴶⬉⑤ⱘ⬉⑤㒓ˈӏԩࠄᏖ⬉㋏㒳
⬉⑤㒓DŽ
⬉⑤㒓ֱᡸ噝ཹᏗ㒓ˈ䙓ܡ㹿䏽䏣ˈ䞡⠽DŽ
㓈ᡸ噝᠔᳝㓈ׂᖙ乏⬅䅸䆕ⱘ㓈ׂҎ䖯㸠DŽ䆒
䚼≵᳝⫼᠋ৃҹᤶⱘ䳊ӊDŽЎ䙓ܡߎ⦄㾺⬉
ϡ㽕㞾Ꮕ䆩ᠧᓔ䆒Ⲫᄤ㓈ׂ䆹䆒DŽ
䗮亢ᄨ噝᳝ѯ䆒ᴎϞ᳝䗮亢ῑᄨˈᅗӀᰃ⫼
䰆ℶᴎݙᬣᛳܗӊ䖛⛁DŽϡ㽕⫼ӏԩϰ㽓ᣵԣ䗮亢ᄨDŽ
䫖⬉∴噝ϡℷ⹂ⱘᤶ⬉∴Ӯ᳝⟚⚌ⱘ䰽DŽᖙ乏Փ
Ϣᆊ㤤ⱘⳌৠⳌ䖥ൟোⱘ⬉∴DŽᣝ✻⫳ѻⱘ
䆂໘⧚ᑳᓗ⬉∴DŽ
im Vertrieb von
CAMBOARD Electronics
www.camboard.de
Tel. 07131 911201
Fax 07131 911203
ce-info@camboard.de
Page 3
Precautions
ᅝܼ乏ⶹ噝Ё᭛
䖭Ͼヺোᦤ⼎⫼᠋䆹䆒⫼᠋ݠЁ
ⱘ᪡㓈ᡸ䇈ᯢDŽ
䖭Ͼヺো䄺⫼᠋䆹䆒ᴎݙᲈ
䴆ⱘ䰽⬉ˈ᳝㾺⬉䰽DŽ
⊼ᛣ
䯙䇏䇈ᯢк噝⫼᠋Փ⫼䆹䆒ࠡᖙ乏䯙䇏ᑊ⧚㾷
᳝ᅝܼՓ⫼䇈ᯢDŽ
ֱᄬ䇈ᯢк噝⫼᠋ᑨֱᄬᅝܼ䇈ᯢкҹᇚᴹՓ⫼DŽ
䙉ᅜ䄺噝⫼᠋ᑨ䙉ᅜѻક⫼᠋ᣛϞⱘ᠔᳝
ᅝܼ᪡䇈ᯢDŽ
䙓ܡ䗑ࡴ噝ϡ㽕Փ⫼䆹ѻકଚ≵᳝㤤ⱘᎹ
䗑ࡴ䆒ˈҹ䙓ܡ䰽DŽ
䄺
⬉⑤噝䆹䆒া㛑Փ⫼ѻકϞᯢⱘ⬉⑤DŽ䆒ᖙ⫼᳝
ഄ㒓կ⬉㋏㒳կ⬉DŽϝᴵ㒓˄ഄ㒓˅ᰃᅝ䆒ᮑˈϡ㛑ϡ
⫼䏇䖛DŽ
ᢨᥝ⬉⑤噝ЎᅝܼഄҢ䆒ᢨᥝ⬉⑤ˈ䇋ᢨᥝ᠔᳝
ৢḠ䴶⬉⑤ⱘ⬉⑤㒓ˈӏԩࠄᏖ⬉㋏㒳
⬉⑤㒓DŽ
⬉⑤㒓ֱᡸ噝ཹᏗ㒓ˈ䙓ܡ㹿䏽䏣ˈ䞡⠽DŽ
㓈ᡸ噝᠔᳝㓈ׂᖙ乏⬅䅸䆕ⱘ㓈ׂҎ䖯㸠DŽ䆒
䚼≵᳝⫼᠋ৃҹᤶⱘ䳊ӊDŽЎ䙓ܡߎ⦄㾺⬉
ϡ㽕㞾Ꮕ䆩ᠧᓔ䆒Ⲫᄤ㓈ׂ䆹䆒DŽ
䗮亢ᄨ噝᳝ѯ䆒ᴎϞ᳝䗮亢ῑᄨˈᅗӀᰃ⫼
䰆ℶᴎݙᬣᛳܗӊ䖛⛁DŽϡ㽕⫼ӏԩϰ㽓ᣵԣ䗮亢ᄨDŽ
䫖⬉∴噝ϡℷ⹂ⱘᤶ⬉∴Ӯ᳝⟚⚌ⱘ䰽DŽᖙ乏Փ
Ϣᆊ㤤ⱘⳌৠⳌ䖥ൟোⱘ⬉∴DŽᣝ✻⫳ѻⱘ
䆂໘⧚ᑳᓗ⬉∴DŽ
im Vertrieb von
CAMBOARD Electronics
www.camboard.de
Tel. 07131 911201
Fax 07131 911203
ce-info@camboard.de
Page 4
This page was deliberately left blank
im Vertrieb von
CAMBOARD Electronics
www.camboard.de
Tel. 07131 911201
Fax 07131 911203
ce-info@camboard.de
Page 5
Chapter One• Introduction ..................................................... 1-1
About the PVT Transmitters ................................................... 1-2
Transmission distance ............................................................ 1-2
About the PVT CV D ............................................................... 1-3
About the PVT CV AAP .......................................................... 1-3
About the PVT RGB D ............................................................1-4
About the PVT RGB AAP ....................................................... 1-4
Application Diagram ................................................................. 1-5
Chapter Two • Installation ...................................................... 2-1
UL/Safety Requirements .........................................................2-2
Important safety instructions ...............................................2-2
Installing the PVT CV D and PVT RGB D ............................. 2-3
Preparing the site and installing the wall box ...................2-3
Final installation ..................................................................... 2-4
Installing the PVT CV AAP and PVT RGB AAP .................. 2-5
Connections and Settings ....................................................... 2-6
Front panel features .............................................................. 2-6
Rear panel features ................................................................ 2-8
PVT CV models ................................................................... 2-8
Cable termination for PVT CV models ............................ 2-8
PVT RGB models ............................................................... 2-10
Cable termination for PVT RGB models ........................ 2-10
Appendix A • Reference Material .....................................A-1
Specifications ..............................................................................A-2
Part Numbers ..............................................................................A-4
Included parts.........................................................................A-4
Optional Accessories ................................................................A-5
AAP accessories ......................................................................A-5
Template Dimensions ...............................................................A-6
PVT Series (D and AAP models) • Table of Contents
Table of Contents
i
All trademarks mentioned in this manual are the properties of their respective owners.
68-1259-01
Rev. B
01 07
im Vertrieb von
CAMBOARD Electronics
www.camboard.de
Tel. 07131 911201
Fax 07131 911203
ce-info@camboard.de
Page 6
PVT Series (D and AAP models) • Table of Contents
ii
Table of Contents, cont'd
This page was deliberately left blank
im Vertrieb von
CAMBOARD Electronics
www.camboard.de
Tel. 07131 911201
Fax 07131 911203
ce-info@camboard.de
Page 7
1
Chapter One
Introduction
About the PVT Transmitters
Application Diagram
PVT Series (D and AAP models)
im Vertrieb von
CAMBOARD Electronics
www.camboard.de
Tel. 07131 911201
Fax 07131 911203
ce-info@camboard.de
Page 8
About the PVT Transmitters
The Extron P�T SeriesP�T Series PoleVault™ Twisted Pair Transmitters
(Decora® and AAP models) described in this manual are a
series of four cost effective twisted pair transmitters that work
exclusively with the PVS 204SA, a four input twisted pair
switcher with a built in power amplifier.
PVT transmitters are capable of transmitting composite video
and stereo audio or high resolution video (RGB) and stereo
audio to the PVS 204SA switcher over twisted pair cable, up to
a distance of 100 feet. All transmitters are remotely powered
via the twisted pair cable when connected to the PVS 204SA
switcher.
N
PVT series of transmitters are compatible ONLY
with the PVS 204SA switcher.
N
For PVS 204SA installation and operation information,
refer to the manual supplied with the device.
The PVT Decora and AAP models can be mounted in UL
standard wall boxes with Decora-style face plates or in AAP
openings in wall or device face plates. The model types are as
follows:
PVT CV D, PVT CV AAP — Transmit composite video and
stereo audio.
PVT RGB D, PVT RGB AAP — Transmit computer (RGB) video
and stereo audio.
See the "About the PVT xx" sections in this chapter for details.
All PVT transmitters are part of a system for distribution of
composite or computer (RGB) video and audio, over Extron
Enhanced Skew-Free™ A/V UTP Cable, or any CAT 5, 5e, or 6
shielded twisted pair (STP), unshielded twisted pair (UTP), or
foil shielded twisted pair (FTP) cable.
Transmission distance
The maximum distance is determined by the frequency and
resolution of the signal that is input to the transmitter. However,
all PVT models are capable of transmitting signals to the
PVS 204SA switcher if it is located not more than 100 feet away.
The optimum distance is between 50 and 75 feet.
PVT Series (D and AAP models) • Introduction
Introduction
1-2
im Vertrieb von
CAMBOARD Electronics
www.camboard.de
Tel. 07131 911201
Fax 07131 911203
ce-info@camboard.de
Page 9
1-3
PVT Series (D and AAP models) • Introduction
About the PVT CV D
The P�T C� D (PoleVault Twisted Pair Transmitter) is a wall
or furniture mountable transmitter that fits any single opening
Decora style wall plate. It is capable of transmitting composite
video and stereo audio to the PVS 204SA switcher.
AUDIO IN
L
R
VIDEO IN
AUDIO IN
L
R
VIDEO IN
Figure 1-1 — PVT CV D face and rear panel
About the PVT CV AAP
The P�T C� AAP (PoleVault Twisted Pair Transmitter) fits
a standard double space AAP opening and is capable of
transmitting composite video and stereo audio to the PVS 204SA
switcher.
AUDIO IN
L RVIDEO
IN
PVT CV
Figure 1-2 — PVT CV AAP face and rear panel
im Vertrieb von
CAMBOARD Electronics
www.camboard.de
Tel. 07131 911201
Fax 07131 911203
ce-info@camboard.de
Page 10
Introduction, cont’d
1-4
PVT Series (D and AAP models) • Introduction
About the PVT RGB D
The P�T RGB D (PoleVault Twisted Pair Transmitter) is a
wall or furniture mountable model that fits any single opening
Decora style wall plate. It is capable of transmitting computer
(RGB) video and stereo audio to the PVS 204SA switcher.
COMPUTER IN
AUDIO IN
COMPUTER IN
AUDIO IN
Figure 1-3 — PVT RGB D face and rear panel
N
Two cable runs for each PVT RGB D plate are required
to carry the video and audio signals to the PVS 204SA.
About the PVT RGB AAP
The P�T RGB AAP (PoleVault Twisted Pair Transmitter) fits
a standard double height AAP opening in a wall plate or a
device's front or secondary panel. It is capable of transmitting
computer (RGB) video and stereo audio to the PVS 204SA
switcher.
COMPUTER
IN
AUDIO IN
PVT RGB
Figure 1-4 — PVT RGB AAP face and rear panel
N
Two cable runs for each PVT RGB AAP are required to
carry the video and audio signals to the PVS 204SA.
im Vertrieb von
CAMBOARD Electronics
www.camboard.de
Tel. 07131 911201
Fax 07131 911203
ce-info@camboard.de
Page 11
PVT Series (D and AAP models) • Introduction
1-5
Application Diagram
Figure 1-5 — Typical PVT series system application
using PVT Decora and AAP transmitters with the
PVS 204SA and other Extron devices
L
R
AU
X/M
I
X
IN
DO NO
T G
R
OU
ND
OR
S
HO
R
T
SP
EAK
ER
OUT
P
UT
S!
1B
1A
I
N
P
U
T
S
O
U
T
P
U
T
S
2B
2A
3B
3A
R
S-
232 ML
C/IR
DC
VO
L
4/8 Ohms
AMPL
I
FIED
OU
TP
U
TS
V
OL
/MUT
E
Tx
A
B
C
Rx
IR
12
V
10V
PO
WER
12V
3A MAX
US
LISTED
17TT
A
UD
IO/VIDEO
APP
ARA
TUS
®
RGB
VIDEO
RGB
VIDEO
Extron
PMK 350
Multi-product Projector
Mounting Kit
RS-232 Cable
to Projector
RS-232 Cable
to Switcher
Line Level
Audio
UTP Cables
Extron
PCM 240
Projector Drop
Ceiling Mount
Extron
PMP
Projector
Mount Pole
Extron
UPB 25
Universal Projector
Mounting Bracket
Extron
SPK 18 - 25'
Cable
Extron
MLP 101 D
Mic to Line Preamplifier
Extron
PVT RGB D
VGA & Audio UTP
Transmitter
Extron
PVT CV D
Composite Video
w/ Audio UTP
Transmitter
DVD/VCR
Combo
Laptop
w/ Audio
COMPUTE
R IN
A
UDIO IN
A
UDIO IN
L
R
L
R
VIDEO I
N
MIC IN
A
CTIVE
MUTE
Aux. Video Source
Document Camera
Ext ron
SI 3CT LP
Full-Ra nge
Ceiling Speakers
Ext ron
SI 3CT LP
Full-Ra nge
Ceiling Speakers
Extron
PVS 204SA
PoleVault
Switcher
™
E
x
t
r
o
n
CONFIG
DISPLA
Y
MLC 104 IP Plus
V
OLUME
1
2
3
4
ON
OFF
VIDEO
A
UX
VIDEO
IMA
GE
MUTE
PC
TCP/IP
Network
Extron MLC 104 IP Plus
MediaLink Controller
Projector on/off control,
input switching, and
volume control
Extron
PVT RGB AAP
VGA & Audio UTP
Transmitter
Extron
PVT CV AAP
Composite Video
w/ Audio UTP
Transmitter
VIDEO
IN
TPS
T CV
AU
DIO IN
L
R
COMPUTER
IN
AU
DIO IN
TPS
T RGB
im Vertrieb von
CAMBOARD Electronics
www.camboard.de
Tel. 07131 911201
Fax 07131 911203
ce-info@camboard.de
Page 12
PVT Series (D and AAP models) • Introduction
Introduction, cont'd
1-6
This page was deliberately left blank
im Vertrieb von
CAMBOARD Electronics
www.camboard.de
Tel. 07131 911201
Fax 07131 911203
ce-info@camboard.de
Page 13
2
Chapter Two
Installation
UL/Safety Requirements
Installing the PVT CV D and PVT RGB D
Installing the PVT CV AAP and PVT RGB AAP
Connections and Settings
PVT Series (D and AAP models)
im Vertrieb von
CAMBOARD Electronics
www.camboard.de
Tel. 07131 911201
Fax 07131 911203
ce-info@camboard.de
Page 14
PVT Series (D and AAP models) • Installation
Installation
2-2
Installation
UL/Safety Requirements
The Underwriters Laboratories (UL) requirements listed below
pertain to the safe installation and operation of these devices.
Important safety instructions
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat
registers, stoves, or other apparatus (including amplifiers)
that produce heat.
9. Do not defeat the safety purpose of the polarized or
grounding type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug
has two blades and a third grounding prong. The wide
blade or the third prong are provided for your safety. If
the provided plug does not fit into your outlet, consult an
electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the
point where they exit from the apparatus.
11. Only use attachments/accessories specified by the
manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table
specified by the manufacturer, or sold with the apparatus.
When a cart is used, use caution when moving the cart/
apparatus combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when
unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing
is required when the apparatus has been damaged in any
way, such as power-supply cord or plug is damaged, liquid
has been spilled or objects have fallen into the apparatus,
the apparatus has been exposed to rain or moisture, does
not operate normally, or has been dropped.
im Vertrieb von
CAMBOARD Electronics
www.camboard.de
Tel. 07131 911201
Fax 07131 911203
ce-info@camboard.de
Page 15
Installing the PVT CV D and PVT RGB D
The PVT CV D and PVT RGB D can be each installed in a
one-gang electrical wall box with a Decora wall plate cover
(supplied). If a suitable wall box is already installed, follow
steps 5 through 8 below. To install a new wall box, follow steps
1 through 8 below. Underwriters Laboratories (UL) Listed wall
boxes are recommended.
The installation must conform to national and local electrical
codes and to the wall plate’s size requirements.
The following Underwriters Laboratories (UL) requirements
pertain to the installation of the PVT transmitters into a wall or
furniture.
1. These units are not to be connected to a centralized DC
power source or used beyond their rated voltage range.
2. These units must be installed in UL listed junction boxes.
3. These units must be installed with conduit in accordance
with National Electrical Code.
Preparing the site and installing the wall box
Choose a location that allows cable runs without interference.
Allow enough depth for both the wall box and the cables. The
box should be at least 2.5" (6.4 cm) deep to accommodate the
connectors and cables. Install the cables into the wall, furniture,
or conduits before installing the wall plate.
1. If a wall box is not available to use for a template, use the
dimensions on page A-6 to create a template. If installing
directly into furniture, cut out the center portion of your
template.
2. Place the wall box (or your template) against the
installation surface, and mark the opening guidelines.
3. Cut out the material from the marked area.
4. Insert the wall box into the opening. The box or the wall
plate’s rear connectors should fit easily into the opening.
Enlarge or smooth the edges of the opening if needed.
5. Feed cables for the output devices through the opening
and through the wall box punch-out holes, securing them
with cable clamps to provide strain relief.
6. Trim back and/or insulate exposed cable shields with heat
shrink to reduce the chance of short circuits.
To prevent short circuits, the outer foil shield can be cut
back to the point where the cable exits the cable clamp.
Both braided and foil shields should be connected to an
equipment ground at the other end of the cable.
2-3
PVT Series (D and AAP models) • Installation
im Vertrieb von
CAMBOARD Electronics
www.camboard.de
Tel. 07131 911201
Fax 07131 911203
ce-info@camboard.de
Page 16
7. Connect the output device (PVS 204SA) cables to the rear
of the PVT wall plate. See "Rear Panel Features", later in
this manual, for connector wiring details.
8. Connect input devices (see "Front Panel Features",
later in this manual, for connector details), restore the
power supply, and test the wall plate. Make any cabling
adjustments before final installation, as the cables will be
inaccessible afterwards.
Final installation
After testing and making any adjustments, do the following:
1. Turn off the power supply to the PVS 204SA, and carefully
insert the wall box into the opening.
N
The transmitter's power is supplied by the PVS 204SA.
2. Secure the wall box with nails or screws, leaving the front
edge flush with the outer wall or furniture surface. See
figure 2-1.
N
If attaching the wall box to wood, use four #8 or #10
screws or 10-penny nails. A minimum of 0.5" (1.3 cm)
of screw thread must penetrate the wood.
If attaching the wall box to metal studs or furniture,
use four #8 or #10 self-tapping sheet metal screws or
machine bolts with matching nuts.
Signal
Output
Cable
Cable
Clamp
Wall Stud
Screws
or Nails
Wall Stud
Cable
Clamp
Screws
or Nails
Signal
Output
Cable
Figure 2-1 — Installing the wall box
3. Mount the transmitter into the box, and attach the supplied
Decora faceplate to the transmitter, as shown in figure 2-2.
4. Reconnect the cables and turn on the power supply to the
PVS 204SA. This powers up the wall plates.
Installation, cont’d
PVT Series (D and AAP models) • Installation
2-4
im Vertrieb von
CAMBOARD Electronics
www.camboard.de
Tel. 07131 911201
Fax 07131 911203
ce-info@camboard.de
Page 17
COMPUTER IN
A
UD
IO IN
Wall opening
is flush with
edge of box.
Wall Box
Decora
Faceplate
Extron
PVT RGB D
Figure 2-2 — Mounting the PVT RGB D
Installing the PVT CV AAP and PVT RGB AAP
The PVT CV AAP and PVT RGB AAP must be attached to a
device faceplate or AAP wall plate and cabled before the device
or wall plate is tested and installed in a wall or furniture.
1. Before attaching any cables, insert the AAP’s standoffs
through the holes in the device’s faceplate or AAP wall
plate.
2. Using the supplied #4-40 nuts and captive washers, secure
the AAP to the faceplate or wall plate.
PVT RGB AAP
AAP 102
AAP 102
A
UDIO IN
COMPUTER
IN
PVT RGB
Figure 2-3 — Mounting the PVT RGB AAP
3. Repeat steps 1 and 2 to mount any other AAPs. Cover any
openings in the faceplate with blank plates (provided with
the AAP faceplate).
2-5
PVT Series (D and AAP models) • Installation
im Vertrieb von
CAMBOARD Electronics
www.camboard.de
Tel. 07131 911201
Fax 07131 911203
ce-info@camboard.de
Page 18
Installation, cont’d
4. Be sure to include the AAP connectors as part of the
installation pretest before final installation of the faceplate.
5. For more detailed installation information, refer to the
installation guide shipped with the device.
N The PVT transmitter should be cabled and tested
before it is finally installed into the wall or device face
plate, as the rear panel connections will be inaccessible
after installation.
6. After testing and making any adjustments, turn off the
power supply to the PVS 204SA, and carefully secure the
faceplate on the wall box device.
7. Reconnect the cables and turn on the power supply to the
PVS 204SA. This powers up the AAP plates.
Connections and Settings
C Do not connect these devices to a computer data or
telecommunications network.
Front panel features
The front panel features are the same within these groups:
a) PVT CV D and PVT CV AAP, and
b) PVT RGB D and PVT RGB AAP:
AUDIO IN
L
R
VIDEO IN
1
2
3
PVT CV D
PVT CV AAP
AUDIO IN
L RVIDEO
IN
PVT CV
1
2
3
PVT RGB AAP
PVT RGB D
COMPUTER IN
AUDIO IN
1
4
5
COMPUTER
IN
AUDIO IN
5
4
1
Figure 2-4 — PVT series front panel features
PVT Series (D and AAP models) • Installation
2-6
im Vertrieb von
CAMBOARD Electronics
www.camboard.de
Tel. 07131 911201
Fax 07131 911203
ce-info@camboard.de
Page 19
a
Dual color power LED (all models) — This LED lights
amber when power only (no signal) is applied to the PVT,
and green when power and signal are both present.
b
Audio (left and right) input (C� D and C� AAP models) —
For unbalanced left and right audio input, plug male
RCA audio plugs into these two female RCA jacks
(white = left, red = right).
Tip (+)
Sleeve ( )
Sleeve (Gnd )
Right Channel
(Red Jacket)
Left Channel
(White Jacket)
Tip (Signal)
Figure 2-5 — RCA audio connectors
c
Composite video input (C� D and C� AAP models) —
To input a composite video signal from a suitable
source, insert a male RCA plug into this yellow female
RCA jack.
d
Audio input (RGB D and RGB AAP models) — Plug a
3.5 mm stereo audio plug into this jack for unbalanced
audio input. Wire the plug as shown in figure 2-6.
N Figure 2-6 shows a typical audio connector,
which consists of the tip, ring, and sleeve.
Sleeve ( )
Ring (R)
Tip (L)
Figure 2-6 — 3.5 mm stereo audio plug
e
RGB video input (RGB D and RGB AAP models) —
Connect a computer video source to this 15-pin
HD connector for high resolution RGB video
input.
AUDIO IN
2-7
PVT Series (D and AAP models) • Installation
im Vertrieb von
CAMBOARD Electronics
www.camboard.de
Tel. 07131 911201
Fax 07131 911203
ce-info@camboard.de
Page 20
Rear panel features
All models have the output connectors on the rear panel.
PVT CV models
Figure 2-7 — PVT CV models rear panel features
a
Composite video output — For composite video output, using
CAT 5 UTP cable, connect this RJ-45 female video output
port to one of the two composite video RJ-45 input connectors
(labelled 3 and 4), on the rear panel of the PVS 204SA switcher.
Cable termination for PVT CV models
N
The PVT cable termination method is specific for
PVT transmitters working with the PVS 204SA
switcher. DO NOT connect to an MTP system.
N
RJ-45 termination with CAT 5, CAT 5e, CAT 6, and
Skew-Free A/V UTP cable must comply with the
TIA/EIA T 568A wiring standards for all connections.
N
For composite video signals, the RJ-45 connector must
be wired exactly as shown in figure 2-8, so that the input
video and audio signals are transmitted correctly.
PVT CV AAP
1
1
PVT CV D
Installation, cont’d
PVT Series (D and AAP models) • Installation
2-8
im Vertrieb von
CAMBOARD Electronics
www.camboard.de
Tel. 07131 911201
Fax 07131 911203
ce-info@camboard.de
Page 21
5
Pin
1
2
3
6
7
8
4
Wire color
White-green
Green
White-orange
White-blue
Orange
White-brown
Brown
568A
Blue
Composite
Video and Audio signal
Video +
Video –
+ 5 VDC
Audio L –
GND
Audio R +
Audio R –
Audio L +
Clip Down
Side
1
1&2
3&6 4&5
7&8
234 56 78
1Pins 234 56 78
RJ-45
connector
Twisted
pairs
UTP Cable and
CAT 5 connector
Figure 2-8 — Wiring the twisted pair composite
video and audio cable
4
3
VIDEO
PVT CV D
Input #3
TP cable from
PVT Output
PVT CV D
Input #4
Rear Panel
Rear Panel
Composite Video Input
Connectors on
Rear Panel of PVS 204SA
TP cable from
PVT Output
Figure 2-9 — Connecting the PVT CV D transmitter
to the PVS 204SA switcher
2-9
PVT Series (D and AAP models) • Installation
im Vertrieb von
CAMBOARD Electronics
www.camboard.de
Tel. 07131 911201
Fax 07131 911203
ce-info@camboard.de
Page 22
PVT RGB models
2a
2b
PVT RGB D
RGB OUT
A
B
PVT RGB AAP
6a2b
6a2a
Figure 2-10 — PVT RGB models rear panel features
Ç
RGB A output — Using CAT 5 UTP cable, connect this RJ-45
female output port labelled “RGB A out” to one of the two
input ports (labelled 1A and 2A) on the PVS 204SA switcher.
É
RGB B output — Using CAT 5 UTP cable, connect this RJ-45
female output port labelled “RGB A out” to one of the two
input ports (labelled 1B and 2B) on the PVS 204SA switcher.
Cable termination for PVT RGB models
N
The PVT cable termination method is specific for
PVT transmitters working with the PVS 204SA
switcher. DO NOT connect to an MTP system.
N
RJ-45 termination with CAT 5, CAT 5e, CAT 6, and
Skew-Free A/V UTP cable must comply with the
TIA/EIA T 568A wiring standards for all connections.
N
The cables must be wired exactly as shown in
figure 2-11, so that the output signals (video on cable A,
vertical sync and audio on cable B) are transmitted
correctly.
N
Cable B primarily carries the audio signal, the
vertical sync information, and 5 VDC to power
the PVT transmitter.
Installation, cont’d
PVT Series (D and AAP models) • Installation
2-10
im Vertrieb von
CAMBOARD Electronics
www.camboard.de
Tel. 07131 911201
Fax 07131 911203
ce-info@camboard.de
Page 23
5
Pin
1
Red +
2
Red –
3
H. sync +
Green –
6 H. sync –
7
Blue +
8
Blue –
4
Wire Color
White-green
Green
White-orange
White-blue
Orange
White-brown
Brown
568A
Cable B
Green +
Blue
Cable A
V. sync +
V. sync –
+ 5 VDC
Audio L –
GND
Audio R +
Audio R –
Audio L +
Clip Down
Side
1
1&2
3&6 4&5
7&8
23 45 67 8
RJ-45
Connector
Twisted
Pairs
TP Cable and
CAT 5 Connector
1Pins 2 34 56 78
Figure 2-11 — Wiring the twisted pair RGB video
and audio cable
PVT RGB D
Input #2
PVT RGB D
Input #1
POWER
12V
3A MAX
1B
1A
I
N
P
U
T
S
2B
2A
RGB
RGB Input Connectors on
Rear Panel of PVS 204SA
Cable from
PVT Output A
Cable from
PVT Output B
Cable from
PVT Output A
Cable from
PVT Output B
B
A
A
B
Rear Panel
Figure 2-12 — Connecting the PVT RGB D transmitter
to the PVS 204SA switcher
2-11
PVT Series (D and AAP models) • Installation
im Vertrieb von
CAMBOARD Electronics
www.camboard.de
Tel. 07131 911201
Fax 07131 911203
ce-info@camboard.de
Page 24
Installation, cont’d
PVT Series (D and AAP models) • Installation
2-12
This page was deliberately left blank
im Vertrieb von
CAMBOARD Electronics
www.camboard.de
Tel. 07131 911201
Fax 07131 911203
ce-info@camboard.de
Page 25
A
Appendix A
Reference Material
Specifications
Part Numbers
Optional Accessories
Template Dimensions
PVT Series (D and AAP models)
im Vertrieb von
CAMBOARD Electronics
www.camboard.de
Tel. 07131 911201
Fax 07131 911203
ce-info@camboard.de
Page 26
A-2
PVT Series (D and AAP models) • Reference Material
Reference Material
Video input and loop-through — RGB (RGB models)
Number/signal type ..................... 1 VGA-UXGA RGBHV, RGBS
Connectors ..................................... 1 female 15-pin HD
Nominal level ................................ 0.7 Vp-p for RGB
Minimum/maximum levels ........ Analog: 0.3 V to 1.5 Vp-p with no offset
Impedance ..................................... 75 ohms
Horizontal frequency .................... 15 kHz to 130 kHz
Vertical frequency .......................... 30 Hz to 150 Hz
Return loss ..................................... <-30 dB @ 5 MHz
DC offset (max. allowable)........... 250 mV
Video output — RGB (RGB models)
Number/signal type ..................... 2 analog proprietary signals
Connectors .................................... 2 female RJ-45
Sync — RGB (RGB models)
Input type ...................................... RGBHV, RGBS
Input level ..................................... 3.5 V to 5.5 Vp-p, unterminated
Input impedance .......................... 510 ohms
Max. input voltage ........................ 5.5 Vp-p
Video — composite video (CV models)
Gain ................................................ Unity
Differential phase error ............... <1.0º at 3.58 MHz and 4.43 MHz
Differential gain error .................. <1.0% at 3.58 MHz and 4.43 MHz
Video input — composite video (CV models)
Number/signal type ..................... 1 composite video
Connectors .................................... 1 female RCA
Nominal level ................................ 1 Vp-p for composite video
Minimum/maximum levels ........ Analog: 0.3 V to 1.5 Vp-p with no offset
Impedance ..................................... 75 ohms
Return loss ..................................... <-30 dB @ 10 MHz
DC offset (max. allowable)........... 100 mV
Specifications
N These transmitters are compatible only with the Extron
PVS 204SA. They are not compatible with other models of
twisted pair receivers.
Video — RGB (RGB models)
Gain ................................................ Unity
im Vertrieb von
CAMBOARD Electronics
www.camboard.de
Tel. 07131 911201
Fax 07131 911203
ce-info@camboard.de
Page 27
PVT Series (D and AAP models) • Reference Material,
A-3
Video output — composite video (CV models)
Number/signal type ..................... 1 analog proprietary signal
Connectors .................................... 1 female RJ-45
Sync — composite video (CV models)
Standards ........................................ NTSC 3.58, NTSC 4.43, PAL, SECAM
Audio input
Number/signal type ..................... 1 stereo, unbalanced
Connectors
RGB models ....................... (1) 3.5 mm audio jack (tip, ring, sleeve)
CV models .......................... 1 pair female RCA
Impedance ..................................... >10k ohms unbalanced, AC coupled
Nominal level ................................ -10 dBV (316 mVrms)
Maximum level ............................. +11 dBV, (unbalanced) at 1% THD+N
N 0 dBu = 0.775 Vrms, 0 dBV =1 Vrms, 0 dBV ≈ 2 dBu
Audio output to a PVS 204SA
Number/signal type .................... 1 analog proprietary signal
Connectors .................................... 1 female RJ-45
General
External power supply ................. Remote power from PVS 204SA
Power input requirement ............. 5 VDC
Rack mount
PVT Decora models .......... No, but mountable in a standard
Decora opening.
PVT AAP models .............. No, but mountable in a double height
AAP opening.
Enclosure type .............................. Metal
Enclosure dimensions
PVT Decora models
Faceplate ........................ 2.6" H x 1.3" W x 0.1" D
6.6 cm H x 3.3 cm W x 0.3 cm D
Device ............................ 2.6" H x 1.6" W x 0.7" D
6.6 cm H x 4.2 cm W x 1.7 cm D
PVT AAP models
Faceplate ........................ 1.4" H x 3.5" W x 0.1" D
3.6 cm H x 8.9 cm W x 0.2 cm D
Device ............................ 1.4" H x 2.6" W x 0.7" D
3.6 cm H x 6.6 cm W x 1.8 cm D
im Vertrieb von
CAMBOARD Electronics
www.camboard.de
Tel. 07131 911201
Fax 07131 911203
ce-info@camboard.de
Page 28
PVT Series (D and AAP models) • Reference Material
Reference Material, cont’d
A-4
Product weight .............................. Various in lbs (kg)
Shipping weight ............................ Various in lbs (kg)
Vibration ........................................ ISTA 1A in carton
(International Safe Transit Association)
Listings............................................ UL, CUL
Compliances ................................... CE, FCC Class A, VCCI, AS/NZS, ICES
MTBF ............................................... 30,000 hours
Warranty ........................................ 3 years parts and labor
N All nominal levels are at ±10%.
N Specifications are subject to change without notice.
Part Numbers
Item Part number
PVT CV D, white
68-819-03
PVT RGB D, white
60-820-03
PVT CV AAP, black, white, RAL9010 70-579-02, 03, 05
PVT RGB AAP, black, white, RAL9010 70-580-02, 03, 05
Included Parts
Unless indicated, these items are included with each PVT Series
transmitter.
Included parts Part number
(1) Single gang Decora® wall plate *
(2) 6-32, 7/8L, mount screws *
70-519-1x
Tweeker (small screwdriver)
User’s manual
N
* Items with PVT RGB D and PVT CV D models only
im Vertrieb von
CAMBOARD Electronics
www.camboard.de
Tel. 07131 911201
Fax 07131 911203
ce-info@camboard.de
Page 29
PVT Series (D and AAP models) • Reference Material
A-5
Optional Accessories
Item Part number
Enhanced Skew-Free A/V UTP cables 26-569-xx
Enhanced Skew-free A/v UTP cables-plenum 26-570-xx
CAT 5 cable, 35', plenum 26-637-35
CAT 5 cable, 50', plenum 26-637-50
CAT 5 cable, 75', plenum 26-637-75
CAT 5 cable, 100', plenum 26-637-100
AAP accessories
N All the accessories in this table are for AAP models only.
Item Part number
AAP 100 panel, black, white, RAL9010 60-593-02, 03, 05
AAP 102 panel, black, white, RAL9010 60-300-02, 03, 05
AAP 104 panel, black, white, RAL9010 60-301-02, 03, 05
AAP 106 panel, black, white, RAL9010 60-531-02, 03, 05
AAP 201 panel, ½ rack width, 1U, black, white 60-302-02, 03
AAP 202 panel, ½ rack width, 2U, black, white 60-303-02, 03
AAP 301 panel, 1 rack width, 1U, black, white 60-632-02, 03
AAP 302 panel, 1 rack width, 2U, black, white 60-633-02, 03
im Vertrieb von
CAMBOARD Electronics
www.camboard.de
Tel. 07131 911201
Fax 07131 911203
ce-info@camboard.de
Page 30
PVT Series (D and AAP models) • Reference Material
Reference Material, cont’d
A-6
Template Dimensions
If you need to create a template, use the dimensions shown
below.
N
The drawing is not full size or to scale.
Do not scale up or print to use as a template.
4.50"
(11.43 cm)
Top
Panel
SURFACE CUT-OUT
AREA FOR
FURNITURE MOUNT
2.79"
(7.09 cm)
1.9"
(4.83 cm)
2.8"
(7.1 cm)
To install a
1-gang
PVT CV D or
PVT RGB D
directly into
furniture or
wall, cut along
this line.
im Vertrieb von
CAMBOARD Electronics
www.camboard.de
Tel. 07131 911201
Fax 07131 911203
ce-info@camboard.de
Page 31
FCC Class A Notice
Note: This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference, in which case the
user will be required to correct the interference at his own expense.
Note: This unit was tested with shielded cables on the peripheral devices. Shielded
cables must be used with the unit to ensure compliance.
Extron’s Warranty
Extron Electronics warrants this product against defects in materials and workmanship
for a period of three years from the date of purchase. In the event of malfunction during
the warranty period attributable directly to faulty workmanship and/or materials,
Extron Electronics will, at its option, repair or replace said products or components,
to whatever extent it shall deem necessary to restore said product to proper operating
condition, provided that it is returned within the warranty period, with proof of
purchase and description of malfunction to:
USA, Canada, South America, Europe, Africa, and the Middle East:
and Central America:
Extron Electronics, Europe
Extron Electronics Beeldschermweg 6C
1001 East Ball Road 3821 AH Amersfoort
Anaheim, CA 92805, USA The Netherlands
Asia: Japan:
Extron Electronics, Asia Extron Electronics, Japan
135 Joo Seng Road, #04-01 Kyodo Building,
PM Industrial Bldg. 16 Ichibancho
Singapore 368363 Chiyoda-ku, Tokyo 102-0082
Japan
This Limited Warranty does not apply if the fault has been caused by misuse, improper
handling care, electrical or mechanical abuse, abnormal operating conditions or nonExtron authorized modification to the product.
If it has been determined that the product is defective, please call Extron and ask for an
Applications Engineer at (714) 491-1500 (USA), 31.33.453.4040 (Europe), 65.6383.4400
(Asia), or 81.3.3511.7655 (Japan) to receive an RA# (Return Authorization number). This
will begin the repair process as quickly as possible.
Units must be returned insured, with shipping charges prepaid. If not insured, you
assume the risk of loss or damage during shipment. Returned units must include the
serial number and a description of the problem, as well as the name of the person to
contact in case there are any questions.
Extron Electronics makes no further warranties either expressed or implied with respect
to the product and its quality, performance, merchantability, or fitness for any particular
use. In no event will Extron Electronics be liable for direct, indirect, or consequential
damages resulting from any defect in this product even if Extron Electronics has been
advised of such damage.
Please note that laws vary from state to state and country to country, and that some
provisions of this warranty may not apply to you.
im Vertrieb von
CAMBOARD Electronics
www.camboard.de
Tel. 07131 911201
Fax 07131 911203
ce-info@camboard.de
Page 32
© 2007 Extron Electronics. All rights reserved.
Extron Electronics, USA
1230 South Lewis Street
Anaheim, CA 92805
800.633.9876 714.491.1500
FAX 714.491.1517
Extron Electronics, Europe
Beeldschermweg 6C
3821 AH Amersfoort, The Netherlands
+800.3987.6673 +31.33.453.4040
FAX +31.33.453.4050
Extron Electronics, Asia
135 Joo Seng Rd. #04-01
PM Industrial Bldg., Singapore 368363
+800.7339.8766 +65.6383.4400
FAX +65.6383.4664
Extron Electronics, Japan
Kyodo Building, 16 Ichibancho
Chiyoda-ku, Tokyo 102-0082
Japan
+81.3.3511.7655 FAX +81.3.3511.7656
www.extron.com
im Vertrieb von
CAMBOARD Electronics
www.camboard.de
Tel. 07131 911201
Fax 07131 911203
ce-info@camboard.de
Loading...