Extron Electronics P-S 100 User Manual

when power is applied and an overcurrent condition (2.0
amps or more) exists.

Continued operation in an overload condition will
cause premature power supply failure.

Channel Overload LEDs — These rear panel LEDs light

5

red to indicate that an overcurrent condition (0.6 amps or
more, or a short circuit) exists for the associated output.
When the Channel Overload LED lights for a specific
output, that output is switched off.

Specifications

Power input ............................. 100VAC to 240VAC, 50/60 Hz, 31 watts,

internal, auto-switchable

Power output .......................... (10) 12VDC outputs (maximum current of

all outputs 2.0 A )

Temperature/humidity ........ Storage -40° to +158°F (-40° to +70°C) /

10% to 90%, non-condensing
Operating +32° to +113°F (0° to +45°C) /

10% to 90%, non-condensing

Rack mount ............................. Yes, with optional rack shelf, part #60-190-01

Enclosure type ........................ Metal

Enclosure dimensions ........... 1.75" H x 4.4" W x 8.5" D

4.4 cm H x 11.2 cm W x 21.6 cm D

Product weight ....................... 1.0 lbs (0.5 kg)

Shipping weight ..................... 3 lbs (1.4 kg)

Vibration .................................. ISTA/NSTA 1A in carton

(International Safe Transit Association)

Listings: .................................... UL, CUL

Compliances: ........................... CE

MTBF ........................................ 30,000 hours

Warranty .................................. 3 years parts and labor

Specifications are subject to change without notice.

User’s Guide

www.extron.com

Extron Electronics, USA

1230 South Lewis Street
Anaheim, CA 92805
USA

714.491.1500
Fax [phone]

Extron Electronics, Europe

Beeldschermweg 6C
3821 AH Amersfoort
The Netherlands
+31.33.453.4040
Fax [phone]

© 2002 Extron Electronics. All rights reserved.

Extron Electronics, Asia

135 Joo Seng Road, #04-01
PM Industrial Building
Singapore 368363
+65.6383.4400
Fax [phone]

Extron Electronics, Japan

Daisan DMJ Building 6F
3-9-1 Kudan Minami
Chiyoda-ku, Tokyo 102-0074 Japan
+81.3.3511.7655
Fax [phone]

P/S 100

Universal 12VDC Power Supply

68-527-01 Rev. C

Printed in the USA

07 02

Installation

1

2

345

- wire

+ wire

- wire

Up to 5 power
supply outputs

Power connector

plastic cover

+ wire

Description

The Extron P/S 100 is a 12VDC 2.0 A universal power supply
with ten separate outputs on two 10-connector, 3.5mm captive
screw connectors. The outputs are rated at 12V, 200 mA each.
The universal power supply can power up to ten devices that
require 12VDC external power, such as some Extron interfaces
and products in the VersaTools™ line of basic distribution
amplifiers, switchers, and associated video accessories.

The rack mountable P/S 100 has an internal auto-switchable
power supply that can accept 100VAC to 240VAC at 50 Hz to 60 Hz.

Installation

For optional rack mounting, mount up to four P/S 100s on a 19"
1U Universal Rack Shelf (Extron part #60-190-01) (figure 1).

Half rack width
false front panel
uses 2 front holes

Quarter Rack Width
False Front Panel

Rear Panel Connections

Connect the power cables from the various devices that

1

will receive power from the P/S 100 to the 3.5mm captive
screw connectors (included) (figure 2).

100-240V -

2

50/60 Hz 0.9 A MAX

3

Figure 2 — P/S 100 front and rear panels

Each captive screw connector has ten poles and can
support up to five power supply outputs (figure 3).

5

1

2 3 4 5 6 7 8 9 10

4

POWER-GREEN

OVERLOAD-AMBER

CHANNEL OVERLOAD

12 VDC OUTPUT 200 mA PER CHANNEL

1

12 VDC POWER SUPPLY

P/S 100

(2) 4-40 x 3/16" screws

1
2

V

D
C

P

P

/

S

O
W

1

E

0

R

0

S

U

P
P

L
Y

Use 2 mounting holes
on opposite corners

Figure 1 — Rack mounting the P/S 100

1. Mount the P/S 100 on the rack shelf, using two 4-40 x 3/16”
screws in opposite (diagonal) corners.

2. If necessary, mount the half rack width false front panel
(included with the Universal Rack Shelf) and/or the quarter
rack width false front panel (included with the P/S 100) to
the shelf, using two 4-40 x 3/16” screws in the front holes
for each panel.

Figure 3 — Connecting power cables to P/S 100

2

Indications

3

4

Plug in the P/S 100.

Power LED — This front panel LED (figure 3) lights to
indicate that the P/S 100 is receiving power.

Power/Overload LED — This rear panel LED lights green
when power is applied and is normal, and lights amber

P/S 100 • IndicationsP/S 100 • Installation

32