User’s Manual
PA 300
Peaking Amplifier
68-1108-01 B
12 08
Precautions
Safety Instructions • English
This symbol is intended to alert the user of important
operating and maintenance (servicing) instructions in
the literature provided with the equipment.
This symbol is intended to alert the user of the
presence of uninsulated dangerous voltage within
the product’s enclosure that may present a risk of
electric shock.
Caution
Read Instructions • Read and understand all safety and operating
instructions before using the equipment.
Retain Instructions • The safety instructions should be kept for future
reference.
Follow Warnings • Follow all warnings and instructions marked on the
equipment or in the user information.
Avoid Attachments • Do not use tools or attachments that are not
recommended by the equipment manufacturer because they may be
hazardous.
Consignes de Sécurité • Français
Ce s ymbole s ert à a vertir l ’utilisa teur qu e la
documentation fournie avec le matériel contient des
instructions importantes concernant l’exploitation et
la maintenance (réparation).
Ce symbole sert à avertir l’utilisateur de la présence
dans le boîtier de l’appareil de tensions dangereuses
non isolées posant des risques d’électrocution.
Attention
Lire les instructions• Prendre connaissance de toutes les consignes de
sécurité et d’exploitation avant d’utiliser le matériel.
Conserver les instructions• Ranger les consignes de sécurité afin de pouvoir
les consulter à l’avenir.
Respecter les avertissements • Observer tous les avertissements et consignes
marqués sur le matériel ou présentés dans la documentation utilisateur.
Eviter les pièces de xation • Ne pas utiliser de pièces de fixation ni d’outils
non recommandés par le fabricant du matériel car cela risquerait de poser
certains dangers.
Sicherheitsanleitungen • Deutsch
Dies es Sym bol so ll dem Benut zer in der i m
Li efe rum fan g e nth alt ene n Do kum ent ati on
besonders wichtige Hinweise zur Bedienung und
Wartung (Instandhaltung) geben.
Dieses Symbol soll den Benutzer darauf aufmerksam
machen , daß im I nneren des Gehäuses d ieses
Produktes gefährliche Spannungen, die nicht isoliert
sind und die einen elektrischen Schock verursachen
können, herrschen.
Achtung
Lesen der Anleitungen • Bevor Sie das Gerät zum ersten Mal verwenden,
sollten Sie alle Sicherheits-und Bedienungsanleitungen genau durchlesen
und verstehen.
Aufbewahren der Anleitungen • Die Hinweise zur elektrischen Sicherheit
des Produktes sollten Sie aufbewahren, damit Sie im Bedarfsfall darauf
zurückgreifen können.
Befolgen der Warnhinweise • Befolgen Sie alle Warnhinweise und
Anleitungen auf dem Gerät oder in der Benutzerdokumentation.
Keine Zusatzgeräte • Verwenden Sie keine Werkzeuge oder Zusatzgeräte,
die nicht ausdrücklich vom Hersteller empfohlen wurden, da diese eine
Gefahrenquelle darstellen können.
Instrucciones de seguridad • Español
Este símbolo se util iza para advertir al usuario
sobre instruc ciones importantes de ope ración y
mantenimiento (o cambio de partes) que se desean
destac ar en el c ontenido de la docume ntación
suministrada con los equipos.
Este símbolo se utiliza para advertir al usuario sobre
la presencia de elementos con voltaje peligroso sin
protección aislante, que puedan encontrarse dentro
de la caja o alojamiento del producto, y que puedan
representar riesgo de electrocución.
Precaucion
Leer las instrucciones • Leer y analizar todas las instrucciones de operación y
seguridad, antes de usar el equipo.
Conservar las instrucciones • Conservar las instrucciones de seguridad para
futura consulta.
Obedecer las advertencias • Todas las advertencias e instrucciones marcadas
en el equipo o en la documentación del usuario, deben ser obedecidas.
Evitar el uso de accesorios • No usar herramientas o accesorios que no
sean especificamente recomendados por el fabricante, ya que podrian
implicar riesgos.
Warning
Power sources • This equipment should be operated only from the power source
indicated on the product. This equipment is intended to be used with a main power
system with a grounded (neutral) conductor. The third (grounding) pin is a safety
feature, do not attempt to bypass or disable it.
Power disconnection • To remove power from the equipment safely, remove all power
cords from the rear of the equipment, or the desktop power module (if detachable),
or from the power source receptacle (wall plug).
Power cord protection • Power cords should be routed so that they are not likely to be
stepped on or pinched by items placed upon or against them.
Servicing • Refer all servicing to qualified service personnel. There are no user-
serviceable parts inside. To prevent the risk of shock, do not attempt to service
this equipment yourself because opening or removing covers may expose you to
dangerous voltage or other hazards.
Slots and openings • If the equipment has slots or holes in the enclosure, these are
provided to prevent overheating of sensitive components inside. These openings
must never be blocked by other objects.
Lithium battery • There is a danger of explosion if battery is incorrectly
replaced. Replace it only with the same or equivalent type recommended by
the manufacturer. Dispose of used batteries according to the manufacturer’s
instructions.
Avertissement
Alimentations• Ne faire fonctionner ce matériel qu’avec la source d’alimentation
indiquée sur l’appareil. Ce matériel doit être utilisé avec une alimentation principale
comportant un fil de terre (neutre). Le troisième contact (de mise à la terre) constitue
un dispositif de sécurité : n’essayez pas de la contourner ni de la désactiver.
Déconnexion de l’alimentation• Pour mettre le matériel hors tension sans danger,
déconnectez tous les cordons d’alimentation de l’arrière de l’appareil ou du module
d’alimentation de bureau (s’il est amovible) ou encore de la prise secteur.
Protection du cordon d’alimentation • Acheminer les cordons d’alimentation de
manière à ce que personne ne risque de marcher dessus et à ce qu’ils ne soient pas
écrasés ou pincés par des objets.
Réparation-maintenance • Faire exécuter toutes les interventions de réparation-
maintenance par un technicien qualifié. Aucun des éléments internes ne peut être
réparé par l’utilisateur. Afin d’éviter tout danger d’électrocution, l’utilisateur ne doit
pas essayer de procéder lui-même à ces opérations car l’ouverture ou le retrait des
couvercles risquent de l’exposer à de hautes tensions et autres dangers.
Fentes et orices • Si le boîtier de l’appareil comporte des fentes ou des orifices, ceux-ci
servent à empêcher les composants internes sensibles de surchauffer. Ces ouvertures
ne doivent jamais être bloquées par des objets.
Lithium Batterie • Il a danger d’explosion s’ll y a remplacment incorrect de la batterie.
Remplacer uniquement avec une batterie du meme type ou d’un ype equivalent
recommande par le constructeur. Mettre au reut les batteries usagees conformement
aux instructions du fabricant.
Vorsicht
Stromquellen • Dieses Gerät sollte nur über die auf dem Produkt angegebene
Stromquelle betrieben werden. Dieses Gerät wurde für eine Verwendung mit einer
Hauptstromleitung mit einem geerdeten (neutralen) Leiter konzipiert. Der dritte
Kontakt ist für einen Erdanschluß, und stellt eine Sicherheitsfunktion dar. Diese
sollte nicht umgangen oder außer Betrieb gesetzt werden.
Stromunterbrechung • Um das Gerät auf sichere Weise vom Netz zu trennen, sollten
Sie alle Netzkabel aus der Rückseite des Gerätes, aus der externen Stomversorgung
(falls dies möglich ist) oder aus der Wandsteckdose ziehen.
Schutz des Netzkabels • Netzkabel sollten stets so verlegt werden, daß sie nicht im
Weg liegen und niemand darauf treten kann oder Objekte darauf- oder unmittelbar
dagegengestellt werden können.
Wartung • Alle Wartungsmaßnahmen sollten nur von qualiziertem Servicepersonal
durchgeführt werden. Die internen Komponenten des Gerätes sind wartungsfrei.
Zur Vermeidung eines elektrischen Schocks versuchen Sie in keinem Fall, dieses
Gerät selbst öffnen, da beim Entfernen der Abdeckungen die Gefahr eines
elektrischen Schlags und/oder andere Gefahren bestehen.
Schlitze und Öffnungen • Wenn das Gerät Schlitze oder Löcher im Gehäuse aufweist,
dienen diese zur Vermeidung einer Überhitzung der empndlichen Teile im
Inneren. Diese Öffnungen dürfen niemals von anderen Objekten blockiert werden.
Litium-Batterie • Explosionsgefahr, falls die Batterie nicht richtig ersetzt
wird. Ersetzen Sie verbrauchte Batterien nur durch den gleichen oder einen
vergleichbaren Batterietyp, der auch vom Hersteller empfohlen wird. Entsorgen Sie
verbrauchte Batterien bitte gemäß den Herstelleranweisungen.
Advertencia
Alimentación eléctrica • Este equipo debe conectarse únicamente a la fuente/tipo
de alimentación eléctrica indicada en el mismo. La alimentación eléctrica de este
equipo debe provenir de un sistema de distribución general con conductor neutro
a tierra. La tercera pata (puesta a tierra) es una medida de seguridad, no puentearia
ni eliminaria.
Desconexión de alimentación eléctrica • Para desconectar con seguridad la acometida
de alimentación eléctrica al equipo, desenchufar todos los cables de alimentación
en el panel trasero del equipo, o desenchufar el módulo de alimentación (si fuera
independiente), o desenchufar el cable del receptáculo de la pared.
Protección del cables de alimentación • Los cables de alimentación eléctrica se deben
instalar en lugares donde no sean pisados ni apretados por objetos que se puedan
apoyar sobre ellos.
Reparaciones/mantenimiento • Solicitar siempre los servicios técnicos de personal
calificado. En el interior no hay partes a las que el usuario deba acceder. Para evitar
riesgo de electrocución, no intentar personalmente la reparación/mantenimiento
de este equipo, ya que al abrir o extraer las tapas puede quedar expuesto a voltajes
peligrosos u otros riesgos.
Ranuras y aberturas • Si el equipo posee ranuras o orificios en su caja/alojamiento,
es para evitar el sobrecalientamiento de componentes internos sensibles. Estas
aberturas nunca se deben obstruir con otros objetos.
Batería de litio • Existe riesgo de explosión si esta batería se coloca en la posición
incorrecta. Cambiar esta batería únicamente con el mismo tipo (o su equivalente)
recomendado por el fabricante. Desachar las baterías usadas siguiendo las
instrucciones del fabricante.
ᅝܼ乏ⶹ•Ё᭛
䖭Ͼヺোᦤ⼎⫼᠋䆹䆒⫼᠋ݠЁ
᳝䞡㽕ⱘ᪡㓈ᡸ䇈ᯢDŽ
䖭Ͼヺো䄺⫼᠋䆹䆒ᴎݙ᳝ᲈ
䴆ⱘ䰽⬉ˈ᳝㾺⬉䰽DŽ
⊼ᛣ
䯙䇏䇈ᯢк• 䑩ㅸỀ䑩嬦嫿⡈⼆枼敆嬼䍇
夤ㆁ㙊⫊₩⏍Ề䑩嬵㕏ɿ
ֱᄬ䇈ᯢк• 䑩ㅸⷕ⪙⫊₩嬵㕏ᶧḦ⡈⭇㚦Ề
䑩ɿ
䙉ᅜ䄺• 䑩ㅸⷕ徶⫉␂⏍䑩ㅸ㉈⊘ᵋ䗅ㆁ㙊⫊
₩⏍㐎ẝ嬵㕏ɿ
䙓ܡ䗑ࡴ• ᵎ壂Ề䑩嬦␂⋃⒇㯢㙊㋩劑䗅₸ㅗ
弾⇡嫿⡈澤Ḧ忀₎⊲斪ɿ
䄺
⬉⑤• 嬦嫿⡈⌫倾Ề䑩␂ᵋ㝈㕏䗅䑶㷑ɿ嫿⡈
⼆枼Ề䑩㙊♱一䗅Ờ䑶䰼丠Ờ䑶ɿ䩭ᵊ㚢一
澠♱一澡㕰⫊₩嫿㓾澤ᵎ倾ᵎ䑩ㅗ崴弈ɿ
ᢨᥝ⬉⑤• ᵻ⫊₩♱ḏ嫿⡈㈕㋊䑶㷑澤嬸㈕㋊ㆁ㙊嫿⡈⍏
ㅗ㞍暣䑶㷑䗅䑶㷑一澤ㅗḼẖ㋦ⅱⵃ䑶䰼丠䗅䑶㷑一ɿ
⬉⑤㒓ֱᡸ• ⣦Ⓟⵄ一澤忀₎埬嵪嵐澤ㅗ愎䆪㉥⋌ɿ
㓈ᡸ•ㆁ㙊丵Ἧ⼆枼䑲嫥嬂䗅丵Ἧ⎙弜垍ɿ嫿⡈怩㯢
㙊䑩ㅸ⌰Ḧ㘵㊣䗅昷ḷɿᵻ忀₎℻䋱大䑶⊲斪ᵎ壂儫ⴲ
嬖☿㆔⹁嫿⡈䘗⪑丵Ἧ嬦嫿⡈ɿ
䗮亢ᄨ• 㙊嫿⡈㙻⠴ᵋ㙊彛栏㤾ㅗ⪕澤⫄ḭ㕰䑩㚦敳㪣
㙻㒐だ₄ḷ弈䀮ɿᵎ壂䑩Ḽẖᵝ壀㉢Ẑ彛栏⪕ɿ
䫖⬉∴• ᵎ㪤䞯䗅㘵㊣䑶㮡ṛ㙊䅇㿹䗅⊲斪ɿ⼆枼Ề䑩ᵏ
⋃⫷㋩劑䗅䘹⍍ㅗ䘹弒⛌⌸䗅䑶㮡ɿ㉊䂨䑠⋃䗅⸻
嫯⡅䍇ⷠ⹄䑶㮡ɿ
FCC Class A Notice
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. The Class A limits are designed to
provide reasonable protection against harmful interference when the equipment is operated in
a commercial environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely to
cause harmful interference, in which case the user will be required to correct the interference at his
own expense.
N
This unit was tested with shielded cables on the peripheral devices. Shielded cables must be used
with the unit to ensure compliance with FCC emissions limits.
Table of Contents
Chapter One • Introduction ................................................... 1-1
About this Manual ....................................................................1-2
About the PA 300 ....................................................................... 1-2
Features ........................................................................................1-2
Chapter Two • Installation and Operation .................2-1
Installation Overvie ............................................................... 2-2
Mounting the PA 300 ............................................................... 2-2
Tabletop use ........................................................................... 2-3
Rack mounting ....................................................................... 2-3
Under-desk mounting ............................................................ 2-4
Through-desk mounting ........................................................ 2-6
Front Panel Features .................................................................2-7
Rear Panel Features................................................................... 2-7
Cabling .......................................................................................... 2-8
Chapter Three • Adjusting the Display ......................... 3-1
Signal Compatibilit ................................................................. 3-2
Potentiometer Adjustments ................................................... 3-2
Adjusting gain ith an oscilloscope ..................................... 3-2
Adjusting gain ithout an oscilloscope ...............................3-2
Adjusting the peaking .......................................................... 3-3
Appendix A • Specifications, Part Numbers, and
Accessories ........................................................................................A-1
Specications ..............................................................................A-2
Parts ...............................................................................................A-5
Included parts.........................................................................A-5
Optional accessories ..............................................................A-5
Cables......................................................................................A-5
PA 300 Peaking Amplier • Table of Contents
i
Table of Contents, cont’d
All trademarks mentioned in this manual are the properties of their respective owners.
68-1108-01 B
ii
PA 300 Peaking Amplier • Table of Contents
12 08
PA 300
Chapter One
1
Introduction
About this Manual
About the PA 300
Features
Introduction
About this Manual
This manual contains information about the Extron PA 300
peaking amplifier, and includes information on how to install,
operate and troubleshoot the unit.
About the PA 300
The PA 300 is an ultra high performance RGB peaking amplifier
capable of driving a 1600 x 1200 resolution computer signal
over 600 feet (185 m) using Extron Mini HR cables, or 1000 feet
(300 m) using Extron RG6 cable. The PA 300 is compatible with
both RGB and HDTV component signals.
The PA 300 has one gain potentiometer and two peaking
potentiometers on the front panel. On the rear panel, the
PA 300 provides five BNCs for RGBHV input and five BNCs for
RGBHV output. The unit restores the sync signals, but does not
process them for format, polarity, or delay.
The PA 300 is housed in a 1U, half rack, 6" (15.2 cm) deep,
2-piece enclosure, and uses an internal power supply.
Features
Bandwidth — 350 MHz (-3 dB) RGB video bandwidth, fully
loaded.
Gain and peaking control — allows optimized output
compensation for various cable lengths and applications.
Light and compact metal enclosure — 1U, half rack, 6" (15.2 cm)
deep, 2-piece enclosure.
Versatile mounting options — can be set on a table; mounted
on a rack shelf; or mounted through or under a desk,
podium, or tabletop.
Global accessibility — has a universal internal power supply
that allows for worldwide usability.
1-2
PA 300 Peaking Amplier • Introduction
PA 300
Chapter Two
2
Installation and Operation
Installation Overview
Mounting the PA 300
Front Panel Features
Rear Panel Features
Cabling
Installation and Operation
1
2
3
4
5
Installation Overview
Be certain the source device, the PA 300, and the output
device are turned off and disconnected from the power
source.
If desired, mount the PA 300 in a rack or furniture. See
"Mounting the PA 300", below.
Cable the inputs and outputs to the PA 300. See "Cabling"
on page 2-8.
Plug the input device, the PA 300, and the output device
into a grounded AC source.
Turn on the input and output devices.
Mounting the PA 300
The PA 300 peaking amplifier can be set on a table; mounted on
a rack shelf; or mounted through or under a desk, podium, or
tabletop.
The following kits are available for mounting the PA 300:
RSB 129 1U, 9.5" deep basic rack shelf •
(part #60-604-01)
RSU 129 1U, 9.5" deep universal rack shelf kit •
(part #60-190-01)
RSB 126 1U, 6" deep basic rack shelf •
(part #60-604-10)
RSU 126 1U, 6" deep universal rack shelf kit •
(part #60-190-10)
MBU 125 Under-desk mounting kit (part #• 70-077-01)
MBD 129 Through-desk mounting kit (part #• 70-077-02)
The following sections provide instructions for these options.
2-2
PA 300 Peaking Amplier • Installation and Operation
6" Deep Rack Shelf
Front false
faceplate
uses 2
screws.
1/2 Rack Width Front False
Faceplate
Use 2 mounting holes on
opposite corners.
(2) 4-40 x 3/16"
Screws
Tabletop use
Rack mounting
Four self-adhesive rubber feet are included with the PA 300.
For tabletop use, affix one foot at each corner of the bottom side
of the unit and place the unit in the desired location.
For optional rack mounting, do not install the rubber feet.
Mount the PA 300 on a 6" deep, 1U high rack shelf (part
#60-190-10 or 60-604-10) or a 9.5" deep 1U high rack shelf (part
#60-190-01 or 60-604-01).
1. Remove the rubber feet if they were previously installed
on the bottom of the unit.
2. Mount the unit on the rack shelf, using two 4-40 x 3/16"
screws in opposite (diagonal) corners to secure it.
3. Install blank panel(s) or other unit(s) on the rack shelf.
4. Attach the rack shelf to the rack using the supplied bolts.
Mounting the PA 300 on a 6-inch deep rack shelf
PA 300 Peaking Amplier • Installation and Operation
2-3
Installation and Operation, cont’d
Use 2 mounting holes on
opposite corners.
(2) 4-40 x 3/16"
Screws
1U Universal Rack Shelf
Front false
faceplate
uses 2
screws.
1/2 Rack Width Front False
Faceplate
N Using screws longer
than 3/16” will damage
the unit and void the
warranty.
Mounting the PA 300 on a 9.5" deep rack shelf
Under-desk mounting
Furniture-mount (under a desk or shelf) the PA 300 using the
optional mounting kit (part #70-077-01), as illustrated below.
2-4
Under-desk mounting the PA 300
PA 300 Peaking Amplier • Installation and Operation
1. Remove two screws from one side of the unit. Retain the
screws for possible future use.
2. Attach one bracket to the side of the unit, using the
provided machine screws.
3. Repeat steps 1 and 2 on the other side of the unit.
4. Hold the PA 300 with the attached brackets against the
mounting location. On the mounting surface, mark the
location of the four bracket screw holes.
5. Drill pilot holes 1/4" (6.4 mm) deep and 3/32" (2.4 mm)
in diameter in the desk or table at the locations of the
mounting bracket screws. The holes should be drilled
from the underside or inside (concealed side) of the
furniture, where the amplifier will be located.
6. Insert #8 wood screws into the four pilot holes. Tighten
each screw into the mounting surface until slightly less
than 1/4" of the screw head protrudes.
7. Align the mounting screws with the slots in the brackets
and place the unit against the surface, with the screws
through the bracket slots.
8. Slide the unit slightly forward or back, then tighten all four
screws to secure it in place.
PA 300 Peaking Amplier • Installation and Operation
2-5
Installation and Operation, cont’d
Through-desk mounting
Mount the PA 300 through a desk or table, using the optional
mounting kit (part #70-077-02), as illustrated below.
Through-desk mounting the PA 300
2-6
1. Install the brackets as shown above. Tighten the screws
only enough to allow sliding of the brackets.
2. Mark the opening through which the unit will be mounted
— approximately 1.8" by 8.9" (4.6 cm by 22.6 cm).
3. Cut out the material from the installation area.
4. Hold the unit, with the mounting brackets attached, under
the furniture where it will be secured. Mark where the
screws will attach the mounting bracket to the underside
of the furniture.
5. Drill pilot holes 1/4" (6.4 mm) deep and 3/32" (2.4 mm)
in diameter in the desk or table at the locations marked in
step 4.
6. Using the four provided wood screws, attach the brackets
to the mounting surface.
7. Slide the unit up and down or back and forth in the
mounting brackets until the face of the PA 300 is at the
desired height. Tighten the screws that secure the brackets
to the unit.
PA 300 Peaking Amplier • Installation and Operation
GAIN
PEAKING
PA 300
PEAKING AMPLIFIER
LF
HF
1
2
3
RG BH/HVV
PA 300
INPUT OUTPUT
50/60 Hz
100-240V .3A
RG BH/HVV
1
3
2
Front Panel Features
Power LED — Lights when the PA 300 is receiving power.
a
Gain control potentiometer — Adjusts the amount of
b
compensation for amplitude losses caused by cable resistance.
Peaking control potentiometers — provide optimum signal
c
compensation. Separate high and low frequency controls.
LF — Provides adjustment to minimize image streaking.
HF — Provides adjustment for achieving the best image detail.
Rear Panel Features
AC power input connector — Attach a standard IEC power
a
cord (100 VAC to 240 VAC, 50 or 60 Hz).
Input BNC connectors — Connect to the input device.
b
Output BNC connectors — Connect to the output device.
c
PA 300 Peaking Amplier • Installation and Operation
2-7
Installation and Operation, cont’d
RGBHV
RGBS
RGsB,
RsGsBs,
Component
S-Video
Composite
G
B
H/V
V
RG
B
V
R
G
B
H/V
V
G
B
R
H/V
V
G
B
R
H/V
V
R
H/V
RGBHV
VGA
Cabling
The PA 300 is specifically designed for long cable run
applications. For best results, install the amplifier close to the
signal source to drive a long cable to the display.
The inputs of the PA 300 are BNC connectors. If the signal
source uses a 15-pin HD connector, use an Extron SYM BNCM
cable (Extron part #26-533-xx) to make the connection. See the
illustration below.
2-8
N
For component and S-video connections G is luma (Y)
To make input and output connections to other devices, do the
following:
1. Turn off the PC and the local monitor.
2. Connect the output of the RGB source to the PA 300 input.
3. Connect the PA 300 output to the RGB display device.
4. Turn on the source and display devices, then the PA 300.
5. Adjust the front panel potentiometers to achieve the
optimal image quality for your display. See chapter 3,
"Adjusting the Display", for detailed instructions.
PA 300 Peaking Amplier • Installation and Operation
PA 300
Chapter Three
3
Adjusting the Display
Signal Compatibility
Potentiometer Adjustments
Adjusting the Display
Signal Compatibility
The PA 300 processes VGA-UXGA, RGBHV, RGBS, RGBsB,
RsGsBs, HDTV, and component video signals.
Potentiometer Adjustments
The PA 300 achieves superior amplification by using two
independent peaking potentiometers: LF for streaking
adjustment and HF for detail adjustment.
The goal in adjusting the PA 300 Gain and Peaking
potentiometers is to produce a sharp image (i.e., an image free
of streaking or smearing) on the attached display.
An oscilloscope is required for the most accurate gain
adjustment, but gain can also be adjusted by observation. The
following instructions explain how to adjust the gain with
and without the use of an oscilloscope. An oscilloscope is not
necessary for the peaking adjustment.
Adjusting gain with an oscilloscope
To adjust the Gain potentiometer using an oscilloscope:
1. Remove the cable from the source and attach a VTG 300
test generator to this cable.
2. Use the White Field test pattern for the VTG 300 setting.
3. Remove the far end of the cable from the projector and
attach the oscilloscope using 75 ohm termination.
4. Use an Extron Tweeker to adjust the Gain potentiometer
for a 0.7 Vp-p reading from white (top) to black (bottom) of
the waveform.
5. Once gain is successfully adjusted, replace the source and
display cables.
6. See "Adjusting the peaking" on the following page.
Adjusting gain without an oscilloscope
Use an Extron Tweeker to turn the Gain potentiometer until the
image reaches the desired level of brightness.
3-2
PA 300 Peaking Amplier • Adjusting the Displa
Adjusting the peaking
To adjust the Peaking potentiometers, do the following:
1. Using MS Paint and a spreadsheet, create a testing image
on your PC desktop that includes squares, lines, text, and
gradations of color. Use the illustration below as a guide.
2. Adjust the LF (low frequency) potentiometer until the
image is free of streaking. When the LF is over adjusted,
the streaking is the same color as the image, as shown
below.
PA 300 Peaking Amplier • Adjusting the Displa
3-3
Adjusting the Display, cont’d
When the LF is under adjusted, the streaking is the inverse
color of the image, as shown below.
The potentiometer should be adjusted midway between
these two extremes.
3. Adjust the HF potentiometer until both text and icon
images appear sharp. When HF is over adjusted, ghosting
may appear, as illustrated below.
When the HF is under adjusted, smearing may appear, as
shown below.
3-4
The potentiometer should be adjusted midway between
these two extremes.
4. Alternate between adjusting the HF and LF potentiometers
until the display shows a clear and sharp image.
PA 300 Peaking Amplier • Adjusting the Displa
PA 300
Appendix A
A
Specifications, Part Numbers,
and Accessories
Specifications
Parts
Specifications, Part Numbers, and Accessories
Specifications
Video
Gain ................................................ -2.5 to +3.5 dB (x0.75 to x1.4), adjustable;
default = 0 dB
Peaking/equalization
Low frequency ............................... 0 to 4 dB at 10 MHz, adjustable
High frequency .............................. 0 to 15 dB at 120 MHz, adjustable
Bandwidth ..................................... 350 MHz (-3 dB)
Output cable driving distance ..... Up to 600' (185 m) with Extron Mini HR
cable. Up to 1000' (300 m) with Extron
RG6 or RG 59 cable (tested with a
1600x1200, 60 Hz computer video signal)
Video input
Number/signal type .................... 1 analog RGBHV, RGBS, RGsB, RsGsBs,
component video (interlaced, progressive,
HDTV), S-video, composite video
Connectors ..................................... 5 BNC female
Nominal level ................................ 1.0 Vp-p for Y of component video and
S-video and for composite video
0.7 Vp-p for RGB (excluding sync) and for
R-Y and B-Y of component video
0.3 Vp-p for C of S-video
Minimum/maximum levels ........ Analog: 0.4 V to 2.0 Vp-p with no offset at
unity gain
Impedance ...................................... 75 ohms
Horizontal frequency .................... 15 kHz to 150 kHz
Vertical frequency .......................... 40 Hz to 140 Hz
Return loss ..................................... -30 dB @ 0 to 5 MHz
DC offset (max. allowable)........... 1 V
Video output
Number/signal type ..................... 1 analog RGBHV, RGBS, RGsB, RsGsBs,
component video (interlaced, progressive,
HDTV), S-video, composite video
Connectors ..................................... 5 BNC female
Nominal level ................................ 1.0 Vp-p for Y of component video and
S-video, and for composite video
0.7 Vp-p for RGB (excluding sync) and for
R-Y and B-Y of component video
0.3 Vp-p for C of S-video
[excluding sync when gain and peaking
potentiometers are set to unity gain
(follows input)]
A-2
PA 300 Peaking Amplier • Specications, Parts, Accessories
Minimum/maximum levels ........ Analog: 0.4 V to 2.0 Vp-p
Impedance ...................................... 75 ohms
Return loss ..................................... -32 dB @ 5 MHz
DC offset ........................................ ±6 mV with input at 0 offset
Sync
Input type ...................................... RGBHV, RGBS, RGsB, RsGsBs, YUV
(bi-level and tri-level)
Output type .................................... RGBHV, RGBS, RGsB, YUV (bi-level and
tri-level)
Input standards ............................. NTSC 3.58, NTSC 4.43, PAL, SECAM
Input level
RGBHV, RGBS ................... TTL: 1.8 V to 5.0 Vp-p
RGsB, RsGsBs .................... Analog: 0.3 Vp-p
Output level
RGBHV, RGBS ................... TTL: 5.0 Vp-p, unterminated
RGsB, RsGsBs .................... Analog: 0.3 Vp-p, follows input
Input impedance .......................... 510 ohms
Output impedance ....................... 50 ohms
Max. propagation delay ............... H: 50 ns, V: 110 ns
Max. rise/fall time ........................ H: <3 ns, V: <3 ns
Polarity............................................ RGBHV, RGBS: positive or negative
(follows input)
RGsB, RsGsBs: negative
General
Power ............................................. 100 VAC to 240 VAC, 50/60 Hz, 3.6 watts,
internal
Temperature/humidity ................ Storage: -40 to +158 °F (-40 to +70 °C) /
10% to 90%, noncondensing
Operating: +32 to +122 °F (0 to +50 °C) /
10% to 90%, noncondensing
Mounting
Rack mount ........................ Yes, with optional 1U, 9.5" deep rack shelf
(RSU 129, #60-190-01; RSB 129, 60-604-01);
or 1U, 6" deep rack shelf (RSU 126,
#60-190-10; RSB 126, 60-604-10).
Furniture mount ................ Yes, with optional under-desk mounting
kit, part #70-077-01 (MBU 125) or throughdesk mounting kit, part #70-077-02
(MBD 129).
Enclosure type ............................... Metal
PA 300 Peaking Amplier • Specications, Parts, Accessories
A-3
Specifications, Part Numbers, Accessories, cont’d
Enclosure dimensions .................. 1.7'' H x 8.7'' W x 6.0'' D
(1U high, half rack wide)
(4.3 cm H x 22.1 cm W x 15.2 cm D)
(Depth excludes connectors.)
Product weight .............................. 1.5 lbs (0.7 kg)
Shipping weight ........................... 3 lbs (2 kg)
Vibration ......................................... ISTA 1A in carton (International Safe
Transit Association)
Regulatory compliance
Safety ................................... CE, CUL, UL
EMI/EMC .......................... CE, C-tick, FCC Class A, ICES, VCCI
Warranty ......................................... 3 years parts and labor
N
N
All nominal levels are at ±10%.
Specifications are subject to change without notice.
A-4
PA 300 Peaking Amplier • Specications, Parts, Accessories
Parts
Included parts
Included parts Replacement
PA300 60-755-01
IEC power cord
Rubber feet (4)
PA 300 Peaking Amplifier User's Manual
Optional accessories
Description Part Number
1U, 9.5" deep Universal Rack Shelf, RSU 129 60-190-01
1U, 9.5" deep Basic Rack Shelf, RSB 129 60-604-01
1U, 6" deep Universal Rack Shelf, RSU 126 60-190-10
1U, 6" deep Basic Rack Shelf, RSB 126 60-604-10
1U, 1/2 Rack Width, Under-Desk Mount Kit,
MBU 125
1U, 1/2 Rack Width, Through-Desk Mount
Kit, MBD 129
Part number
70-077-01
70-077-02
Cables
BNC cables Part number
MHR-5 BNC 3', 6', 12', 25', 35', 50', 75', 100' 26-260-xx
MHR-5P BNC 3', 6', 12', 25', 35', 50', 75', 100' 26-378-xx
M59-5 BNC 3', 6', 12', 25', 35', 50', 75', 100' 26-499-xx
RG6-5 BNC 3', 6', 12', 25', 35', 50', 75', 100' 26-369-xx
SYM BNCM 6'', 1', 3', 6', 12', 25', 50', 75', 100' 26-533-xx
A-5
Specifications, Part Numbers, Accessories, cont’d
A-6
PA 300 Peaking Amplier • Specications, Parts, Accessories
Extron’s Warranty
Extron Electronics warrants this product against defects in materials and workmanship
for a period of three years from the date of purchase. In the event of malfunction during
the warranty period attributable directly to faulty workmanship and/or materials,
Extron Electronics will, at its option, repair or replace said products or components,
to whatever extent it shall deem necessary to restore said product to proper operating
condition, provided that it is returned within the warranty period, with proof of
purchase and description of malfunction to:
USA, Canada, South America,
and Central America:
Extron Electronics
1001 East Ball Road
Anaheim, CA 92805
U.S.A.
Japan: Extron Electronics, Japan
Kyodo Building, 16 Ichibancho
Chiyoda-ku, Tokyo 102-0082
Japan
Europe, Africa, and the Middle East:
Extron Europe
Hanzeboulevard 10
3825 PH Amersfoort
The Netherlands
Asia:
Extron Asia
135 Joo Seng Road, #04-01
PM Industrial Bldg.
Singapore 368363
Singapore
This Limited Warranty does not apply if the fault has been caused by misuse, improper
handling care, electrical or mechanical abuse, abnormal operating conditions or nonExtron authorized modification to the product.
If it has been determined that the product is defective, please call Extron and ask for
an Applications Engineer at (714) 491-1500 (USA), 31.33.453.4040 (Europe), 65.383.4400
(Asia), or 81.3.3511.7655 (Japan) to receive an RA# (Return Authorization number). This
will begin the repair process as quickly as possible.
Units must be returned insured, with shipping charges prepaid. If not insured, you
assume the risk of loss or damage during shipment. Returned units must include the
serial number and a description of the problem, as well as the name of the person to
contact in case there are any questions.
Extron Electronics makes no further warranties either expressed or implied with respect
to the product and its quality, performance, merchantability, or fitness for any particular
use. In no event will Extron Electronics be liable for direct, indirect, or consequential
damages resulting from any defect in this product even if Extron Electronics has been
advised of such damage.
Please note that laws vary from state to state and country to country, and that some
provisions of this warranty may not apply to you.
China:
Extron China
686 Ronghua Road, Songjiang
District
Shanghai 201611
China
Middle East:
Extron Middle East
Dubai Airport Free Zone
F12, PO Box 293666
United Arab Emirates, Dubai
Extron USA - West
Headquarters
+800.633.9876
Inside USA / Canada Only
+1.714.491.1500
+1.714.491.1517 FAX
Extron USA - East
+800.633.9876
Inside USA / Canada Only
+1.919.863.1794
+1.919.863.1797 FAX
Extron Europe
+800.3987.6673
Inside Europe Only
+31.33.453.4040
+31.33.453.4050 FA X
Extron Asia
+800.7339.8766
Inside Asia Only
+65.6383.4400
+65.6383.4664 FAX
Extron Japan
+81.3.3511.7655
+81.3.3511.7656 FAX
Extron China
+400.883.1568
Inside China Only
+86.21.3760.1568
+86.21.3760.1566 FAX
Extron Middle East
+971.4.2991800
+971.4.2991880 FAX
© 2008 Extron Electronics. All rights reserved.
Loading...