Extron electronics P/2 DA2 D, WM EC F, P/2 DA2 WM EC F AAP, P/2 DA2 EC F User Manual

Download

User’s Manual

Distribution Amplifiers

68-463-02 Rev. C

09 08

P/2 DA2 WM F, WM EC F,

P/2 DA2 D, and AAP models

Precautions

This symbol is intended to alert the user of important operating and maintenance (servicing) instructions in the literature provided with the equipment.

This symbol is intended to alert the user of the presence of uninsulated dangerous voltage within the product's enclosure that may present a risk of electric shock.

Caution

Read Instructions • Read and understand all safety and operating

instructions before using the equipment.

Retain Instructions • The safety instructions should be kept for future

reference.

Follow Warnings • Follow all warnings and instructions marked on the

equipment or in the user information.

Avoid Attachments • Do not use tools or attachments that are not

recommended by the equipment manufacturer because they may be hazardous.

Warning

Power sources • This equipment should be operated only from the power source

indicated on the product. This equipment is intended to be used with a main power system with a grounded (neutral) conductor. The third (grounding) pin is a safety feature, do not attempt to bypass or disable it.

Power disconnection • To remove power from the equipment safely, remove all

power cords from the rear of the equipment, or the desktop power module (if detachable), or from the power source receptacle (wall plug).

Power cord protection • Power cords should be routed so that they are not likely to

be stepped on or pinched by items placed upon or against them.

Servicing • Refer all servicing to qualified service personnel. There are no user-

serviceable parts inside. To prevent the risk of shock, do not attempt to service this equipment yourself because opening or removing covers may expose you to dangerous voltage or other hazards.

Slots and openings • If the equipment has slots or holes in the enclosure, these are

provided to prevent overheating of sensitive components inside. These openings must never be blocked by other objects.

Lithium battery • There is a danger of explosion if battery is incorrectly replaced.

Replace it only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer's instructions.

Ce symbole sert à avertir l’utilisateur que la documentation fournie avec le matériel contient des instructions importantes concernant l’exploitation et la maintenance (réparation).

Ce symbole sert à avertir l’utilisateur de la présence dans le boîtier de l’appareil de tensions dangereuses non isolées posant des risques d’électrocution.

Attention

Lire les instructions• Prendre connaissance de toutes les consignes de

sécurité et d’exploitation avant d’utiliser le matériel.

Conserver les instructions• Ranger les consignes de sécurité afin de

pouvoir les consulter à l’avenir.

Respecter les avertissements • Observer tous les avertissements et

consignes marqués sur le matériel ou présentés dans la documentation utilisateur.

Eviter les pièces de fixation • Ne pas utiliser de pièces de fixation ni

d’outils non recommandés par le fabricant du matériel car cela risquerait de poser certains dangers.

Avertissement

Alimentations• Ne faire fonctionner ce matériel qu’avec la source d’alimentation

indiquée sur l’appareil. Ce matériel doit être utilisé avec une alimentation principale comportant un fil de terre (neutre). Le troisième contact (de mise à la terre) constitue un dispositif de sécurité : n’essayez pas de la contourner ni de la désactiver.

Déconnexion de l’alimentation• Pour mettre le matériel hors tension sans danger,

déconnectez tous les cordons d’alimentation de l’arrière de l’appareil ou du module d’alimentation de bureau (s’il est amovible) ou encore de la prise secteur.

Protection du cordon d’alimentation • Acheminer les cordons d’alimentation de

manière à ce que personne ne risque de marcher dessus et à ce qu’ils ne soient pas écrasés ou pincés par des objets.

Réparation-maintenance • Faire exécuter toutes les interventions de réparation-

maintenance par un technicien qualifié. Aucun des éléments internes ne peut être réparé par l’utilisateur. Afin d’éviter tout danger d’électrocution, l’utilisateur ne doit pas essayer de procéder lui-même à ces opérations car l’ouverture ou le retrait des couvercles risquent de l’exposer à de hautes tensions et autres dangers.

Fentes et orifices • Si le boîtier de l’appareil comporte des fentes ou des orifices,

ceux-ci servent à empêcher les composants internes sensibles de surchauffer. Ces ouvertures ne doivent jamais être bloquées par des objets.

Lithium Batterie • Il a danger d'explosion s'll y a remplacment incorrect de la

batterie. Remplacer uniquement avec une batterie du meme type ou d'un ype equivalent recommande par le constructeur. Mettre au reut les batteries usagees conformement aux instructions du fabricant.

Safety Instructions • English

Consignes de Sécurité • Français

Sicherheitsanleitungen • Deutsch

Dieses Symbol soll den Benutzer auf wichtige Anleitungen zur Bedienung und Wartung (Instandhaltung) in der Dokumentation hinweisen, die im Lieferumfang dieses Gerätes enthalten ist.

Dieses Symbol soll den Benutzer darauf aufmerksam machen, daß im Inneren des Gehäuses dieses Produktes gefährliche Spannungen, die nicht isoliert sind und die einen elektrischen Schock verursachen können, herrschen.

Achtung

Lesen der Anleitungen • Bevor Sie das Gerät zum ersten Mal verwenden,

sollten Sie alle Sicherheits-und Bedienungsanleitungen genau durchlesen und verstehen.

Aufbewahren der Anleitungen • Die Sicherheitsanleitungen sollten

aufbewahrt werden, damit Sie später darauf zurückgreifen können.

Befolgen der Warnhinweise • Befolgen Sie alle Warnhinweise und

Anleitungen auf dem Gerät oder in der Benutzerdokumentation.

Keine Zusatzgeräte • Verwenden Sie keine Werkzeuge oder Zusatzgeräte,

die nicht ausdrücklich vom Hersteller empfohlen wurden, da diese eine Gefahrenquelle darstellen können.

Vorsicht

Stromquellen • Dieses Gerät sollte nur über die auf dem Produkt angegebene

Stromquelle betrieben werden. Dieses Gerät wurde für eine Verwendung mit einer Hauptstromleitung mit einem geerdeten (neutralen) Leiter konzipiert. Der dritte Stift oder Kontakt ist für einen Erdschluß, und stellt eine Sicherheitsfunktion dar und sollte nicht umgangen oder außer Betrieb gesetzt werden.

Stromunterbrechung • Um das Gerät auf sichere Weise vom Netz zu trennen,

sollten Sie alle Netzkabeln aus der Rückseite des Gerätes oder aus dem DesktopStrommodul (falls dies möglich ist) oder aus der Wandsteckdose ziehen.

Schutz des Netzkabels • Netzkabel sollten stets so verlegt werden, daß sie nicht

im Weg liegen und niemand darauf treten kann oder Objekte darauf- oder unmittelbar dagegengestellt werden können.

Wartung • Alle Wartungsmaßnahmen sollten nur von qualifiziertem

Servicepersonal durchgeführt werden. Im Inneren des Gerätes sind keine Teile enthalten, die vom Benutzer gewartet werden können. Zur Vermeidung eines elektrischen Schocks versuchen Sie in keinem Fall, dieses Gerät selbst zu warten, da beim Öffnen oder Entfernen der Abdeckungen die Gefahr eines elektrischen Schlags oder andere Gefahren bestehen.

Schlitze und Öffnungen • Wenn das Gerät Schlitze oder Löcher im Gehäuse

aufweist, dienen diese zur Vermeidung einer Überhitzung der empfindlichen Teile im Inneren. Diese Öffnungen dürfen niemals von anderen Objekten blockiert werden.

Litium-Batterie • Explosionsgefahr, falls die Batterie nicht richtig ersetzt wird.

Ersetzen Sie nur durch diegleiche oder einen vergleichbaren Batterietyp, der auch vom Hersteller empfohlen wird. Entsorgung der verbrauchten Batterien bitte gemäß den Herstelleranweisungen.

Este símbolo se utiliza para advertir al usuario sobre instrucciones importantes de operación y mantenimiento (o cambio de partes) que se desean destacar en el contenido de la documentación suministrada con los equipos.

Este símbolo se utiliza para advertir al usuario sobre la presencia de elementos con voltaje peligroso sin protección aislante, que puedan encontrarse dentro de la caja o alojamiento del producto, y que puedan representar riesgo de electrocución.

Precaucion

Leer las instrucciones • Leer y analizar todas las instrucciones de

operación y seguridad, antes de usar el equipo.

Conservar las instrucciones • Conservar las instrucciones de seguridad

para futura consulta.

Obedecer las advertencias • Todas las advertencias e instrucciones

marcadas en el equipo o en la documentación del usuario, deben ser obedecidas.

Evitar el uso de accesorios • No usar herramientas o accesorios que no

sean especificamente recomendados por el fabricante, ya que podrian implicar riesgos.

Advertencia

Alimentación eléctrica • Este equipo debe conectarse únicamente a la fuente/tipo

de alimentación eléctrica indicada en el mismo. La alimentación eléctrica de este equipo debe provenir de un sistema de distribución general con conductor neutro a tierra. La tercera pata (puesta a tierra) es una medida de seguridad, no puentearia ni eliminaria.

Desconexión de alimentación eléctrica • Para desconectar con seguridad la

acometida de alimentación eléctrica al equipo, desenchufar todos los cables de alimentación en el panel trasero del equipo, o desenchufar el módulo de alimentación (si fuera independiente), o desenchufar el cable del receptáculo de la pared.

Protección del cables de alimentación • Los cables de alimentación eléctrica se

deben instalar en lugares donde no sean pisados ni apretados por objetos que se puedan apoyar sobre ellos.

Reparaciones/mantenimiento • Solicitar siempre los servicios técnicos de personal

calificado. En el interior no hay partes a las que el usuario deba acceder. Para evitar riesgo de electrocución, no intentar personalmente la reparación/ mantenimiento de este equipo, ya que al abrir o extraer las tapas puede quedar expuesto a voltajes peligrosos u otros riesgos.

Ranuras y aberturas • Si el equipo posee ranuras o orificios en su caja/alojamiento,

es para evitar el sobrecalientamiento de componentes internos sensibles. Estas aberturas nunca se deben obstruir con otros objetos.

Batería de litio • Existe riesgo de explosión si esta batería se coloca en la posición

incorrecta. Cambiar esta batería únicamente con el mismo tipo (o su equivalente) recomendado por el fabricante. Desachar las baterías usadas siguiendo las instrucciones del fabricante.

Instrucciones de seguridad • Español

Extron’s Warranty

Extron Electronics warrants this product against defects in materials and workmanship for a period of three years from the date of purchase. In the event of malfunction during the warranty period attributable directly to faulty workmanship and/or materials, Extron Electronics will, at its option, repair or replace said products or components, to whatever extent it shall deem necessary to restore said product to proper operating condition, provided that it is returned within the warranty period, with proof of purchase and description of malfunction to:

USA, Canada, South America, Europe, Africa, and the Middle East: and Central America:

Extron Electronics, Europe Extron Electronics Beeldschermweg 6C 1001 East Ball Road 3821 AH Amersfoort Anaheim, CA 92805, USA The Netherlands

Asia: Japan:

Extron Electronics, Japan Extron Electronics, Asia Kyodo Building 135 Joo Seng Road, #04-01 16 Ichibancho PM Industrial Bldg. Chiyoda-ku, Tokyo 102-0082 Singapore 368363 Japan

This Limited Warranty does not apply if the fault has been caused by misuse, improper handling care, electrical or mechanical abuse, abnormal operating conditions or non-Extron authorized modification to the product.

If it has been determined that the product is defective, please call Extron and ask for an Applications Engineer at (714) 491-1500 (USA), 31.33.453.4040 (Europe),

65.6383.4400 (Asia), or 81.3.3511.7655 (Japan) to receive an RA# (Return Authorization number). This will begin the repair process as quickly as possible.

Units must be returned insured, with shipping charges prepaid. If not insured, you assume the risk of loss or damage during shipment. Returned units must include the serial number and a description of the problem, as well as the name of the person to contact in case there are any questions.

Extron Electronics makes no further warranties either expressed or implied with respect to the product and its quality, performance, merchantability, or fitness for any particular use. In no event will Extron Electronics be liable for direct, indirect, or consequential damages resulting from any defect in this product even if Extron Electronics has been advised of such damage.

Please note that laws vary from state to state and country to country, and that some provisions of this warranty may not apply to you.

P/2 DA2 WM Series, EC, & D

Controls and Installation

FCC Class A Notice

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his own expense.

N This unit was tested with shielded cables on the peripheral devices. Shielded

cables must be used with the unit to ensure compliance.

P/2 DA2 WM/EC/D/AAP Series • Table of ContentsP/2 DA2 WM/EC/D/AAP Series

• •

• Table of Contents

Chapter 1 • Introduction ......................................................... 1-1

About the P/2 DA2 WM F/EC F, AAP and D Models

.................................................................................... 1-2

Features ...................................................................................... 1-2

Chapter 2 • Controls and Installation ........................... 2-1

Front and Rear Panels ................................................. 2-2

Front faceplate ...................................................................... 2-2

P/2 DA2 WM F/EC F rear panel ..............................................2-4

P/2 DA2 D rear panel ............................................................. 2-5

Installing the P/2 DA2 WM F/EC F ............................. 2-7

Easy setup procedure ............................................................ 2-7

Installing the mud ring bracket .............................................2-8

Cabling ..................................................................................2-10

Connecting audio output ..................................................... 2-11

Installing architectural adapter plates ............................... 2-12

P/2 DA2 WM F wall mount installation ...............................2-14

P/2 DA2 WM EC F Euro Channel installation ......................2-15

Setting the DIP switches ......................................................2-15

Setting the internal jumpers ...............................................2-16

Installing the P/2 DA2 D ........................................... 2-17

Preparing the site and installing the wall box ....................2-17

Mounting the distribution amplifier ................................... 2-18

Replacing the faceplate .......................................................2-20

P/2 DA2 D application example .......................................... 2-20

Appendix • Specifications, Dimensions, Parts, and

Templates............................................................................................ A-1

Specifications ......................................................................... A-2

Dimensions .............................................................................. A-7

P/2 DA2 WM F faceplate dimensions ................................... A-7

P/2 DA2 WM F AAP faceplate dimensions .......................... A-8

P/2 DA2 D faceplate dimensions .......................................... A-9

Part and Accessories ......................................................... A-10

Included parts ...................................................................... A-10

Cables .................................................................................. A-10

Mud ring mounting brackets .............................................. A-10

Optional architectural adapter plates ............................... A-11

Table of Contents

P/2 DA2 WM/EC/D/AAP Series • Table of ContentsP/2 DA2 WM/EC/D/AAP Series

• •

• Table of Contents

Chapter One

Introduction

About the P/2 DA2 WM F/ EC F, AAP, and D Models

Features

P/2 DA2 WM/EC/D/AAP Series

Templates ............................................................................... A-15

P/2 DA2 WM F mounting template ................................... A-15

P/2 DA2 WM F AAP mounting template ........................... A-16

P/2 DA2 D mounting template .......................................... A-17

68-463-02 Rev. C

09 08

All trademarks mentioned in this manual are the properties of their respective owners.

Table of Contents, cont’d

P/2 DA2 WM/EC/D/AAP Series • IntroductionP/2 DA2 WM/EC/D/AAP Series •

Introduction

Chapter Two

Controls and Installation

Front and Rear Panels

Installing the P/2 DA2 WM F/EC F

Installing the P/2 DA2 D

P/2 DA2 WM/EC/D/AAP Series

Introduction

About the P/2 DA2 WM F/EC F, AAP, and D Models

The P/2 DA2 WM F/F EC, AAP, and D models are one input, two output, high resolution VGA/XGA distribution amplifiers with audio. With a video bandwidth of 300 MHz, these distribution amplifiers are compatible with VGA, SVGA, VESA, XGA, and SXGA graphics cards, monitors, projectors, and LCD panels. The D model features Decora

faceplates and trim.

For audio, the P/2 DA2 WM F/EC F and D feature a 3.5 mm female jack for input and a 3.5 mm captive screw connector for balanced or unbalanced output. The D model features a DIP switch for selecting stereo or dual mono output.

The P/2 DA2 WM F is the wallmount version and the P/2 DA2 WM EC F is the Euro Channel version. The P/2 DA2 WM F AAP and the P/2 DA2 WM EC F AAP are the same base products, but with AAP faceplates added. These plates are a convenient method of providing various connectors for most audio and video applications.

Features

2-color power/signal LED — When the interface is on, the

power/signal LED lights amber. When the interface is on and a signal is present, the LED lights green.

Gain/peak control— Compensates for signal degradation

caused by long cable lengths.

Stereo audio — Front panel audio input jack and a 3.5 mm

captive screw output connector on the rear panel.

Buffered local monitor output — 15-pin HD female connector Computer video input — 15-pin HD female connector Wall mountable (WM model) — Self-contained enclosure

provides for convenient wall mounting.

Euro Channel mountable (EC model) — This model mounts

easily in the Euro Channel raceway

Optional architectural adapter plates — The

P/2 DA2 WM F AAP may be user-configured with up to four Architectural Adapter Plates (three for the EC AAP version). These adapter plates provide a selection of pass-through signal connectors for various audio and video requirements.

1-2

P/2 DA2 WM/EC/D/AAP Series • Controls and Installation

Unity – output signal level is same as that of input with no added

peaking

50% – increases the output signal level and adds 50% of the maximum

peaking to the signal

N If the edges of the image seem to exceed their boundaries,

or if thin lines and sharp edges look thick and fuzzy, try changing the level/peak setting.

P/2 DA2 WM EC F faceplate features

P/2 DA2 D faceplate features

2-3

Controls and Installation

Front and Rear Panels

Front faceplate

P/2 DA2 WM F faceplate features

N Both WM F and WM EC F models have the same front

and rear panel connectors and features.

2-color power/signal LED — lights amber to indicate power on only; lights green to indicate power on with video signal present.

Audio input jack — 3.5 mm stereo input

VGA input connector — HD 15-pin female analog video input connector

Buffered local monitor output — HD 15-pin female for output to a local monitor

ID bit termination DIP switches — provides proper ID bit termination for a laptop computer that is not attached to a local monitor. See “Setting the DIP switches” in this chapter.

3-position gain/peaking switch — compensates for cable capacitance and resistance due to long cable runs; position switch for best image on the output display device.

100% – increases the output signal level and adds 100% of the

maximum peaking to the signal

2-2

AUTO POWER

P/2 DA2 WM F EC

ID PINS

100%

UNITY

50%

GAIN/

PEAKING

AUDIO IN

COMPUTER IN

MONITOR OUT

AUTO POWER

100%

UNITY

50%

GAIN/PEAKING

P/2 DA2 WM/EC/D/AAP Series • Controls and Installation

P/2 DA2 WM/EC/D/AAP Series • Controls and Installation2-4 2-5

Controls and Installation, cont’d

P/2 DA2 WM F/EC F rear panel

P/2 DA2 WM F/EC F rear connectors

N Both WM F and WM EC F models have the same rear

panel connectors.

Power input — 12 - 24 VAC or DC (captive screw connector). The center pole contains no conductor. Connect the conductors to the outer two poles only.

Audio output — 3.5 mm captive screw stereo output

VGA output — HD 15-pin female analog video output connector

12-24V AC/DC

P/2 DA2 D rear panel

1 2 3 4

12 V

0.2 A MAX POWER

AUDIO

OUTPUT

CONFIG

VIDEO

OUTPUT

P/2 DA2 D

ON 1 2 3 4

1 2 3 4

33-1663-01 A 05 08

CONFIG Switches

SW 1= Local Monitor

ON= Present, OFF= Not Present

SW 2= Audio Ouput Config

ON= Stereo, OFF= Dual MONO

SW 3= SYNC Input Impedance

ON= 510 Ohm,

OFF= 10 kOhm

SW 4= Spare

Extron Electronics

Anaheim, CA

VIDEO

GAIN

NORM

MED

HIGH

N15779

Figure 2-5 — P/2 DA2 D rear connectors

Configuration DIP switches — The three DIP switches (plus one spare) configure the P/2 DA2 D, as shown in the table below.

N The default DIP switch positions are set to On (up).

Set these switches before installing the distribution amplifier in a wall.

1 2 3 4

Switch Function On (up) Off (down)

SW1

SW2

SW3

SW4

local monitor (set ID bits 4

and 11)

audio output

configuration

input sync

impedance

spare

monitor present

stereo

510 ohms

n/a

monitor not present

dual mono

10k ohms

n/a

Audio output — 3.5 mm captive screw stereo or dual mono output (DIP switch selectable, see switch SW 2 in 1 above).

3-Pole Captive Screw Connector

Tie Wrap

3/16”

(5 mm) Max.

P/2 DA2 WM/EC/D/AAP Series • Controls and Installation

2-6

Controls and Installation, cont’d

Installing the P/2 DA2 WM F/EC F

Easy setup procedure

The wall-mounted P/2 DA2 WM F kit consists of the faceplate/ distribution amplifier assembly and a mounting bracket that mounts in a wall opening and to which the faceplate assembly is attached. The P/2 DA2 WM EC F kit consists of the faceplate/ distribution amplifier assembly that mounts in the Euro Channel raceway.

For wall mounting only: Using the mounting template provided in the appendix as a guide, carefully cut a mounting hole through the wall where the mounting bracket is to be installed.

For wall mounting only: Install the mud ring mounting bracket using the supplied screws and mounting clips. Refer to the section “Installing a mud ring bracket” for further details.

Before connecting any cables, power off all equipment. If the optional architectural adapter plate (AAP) is being installed, please refer to “Installing architectural adapter plates” in this chapter.

The rear connectors are the same for both WM F and WM F EC models. Connect the VGA output cable to the 15-pin HD female output connector. To prevent installation debris or objects from entering the opening in the sheet metal just above this VGA connector, use masking tape to temporarily cover this opening. Remove this tape after installation is completed. Next, if there is audio output, connect the audio output cable to the captive screw connector. Finally, connect the power cable to the power input connector. Refer to the “Cabling” and “Connecting audio” sections of this chapter.

Before attaching the faceplate assembly to the wall mounting bracket/Euro Channel, attach the computer video cable to the 15-pin HD female input connector on the faceplate. Next, a local monitor may be connected to the 15-pin HD female buffered local monitor output connector on the faceplate. Finally, for audio input, connect the audio cable to the faceplate’s 3.5 mm audio input jack. Refer to the “Cabling” and “Connecting audio” sections of this chapter. For Euro Channel applications, refer to the “Euro Channel installation” section.

Gain switch — To compensate for cable resistance and capacitance, use a small screwdriver to slide this switch to select the level of video gain that yields the sharpest, smear-free picture.

1 2 3 4

12 V

0.2 A MAX POWER

AUDIO

OUTPUT

CONFIG

VIDEO

OUTPUT

P/2 DA2 D

ON 1 2 3 4

1 2 3 4

33-1663-01 A 05 08

CONFIG Switches

SW 1= Local Monitor

ON= Present, OFF= Not Present

SW 2= Audio Ouput Config

ON= Stereo, OFF= Dual MONO

SW 3= SYNC Input Impedance

ON= 510 Ohm,

OFF= 10 kOhm

SW 4= Spare

Extron Electronics

Anaheim, CA

VIDEO

GAIN

NORM

MED

HIGH

N15779

High –

Max. peaking

& gain

Medium –

Mid-level

peaking

and gain

Normal –

Unity gain

P/2 DA2 D

(viewed

from rear)

N Adjust the gain before installing the P/2 DA2 D

into a wall, as the gain switch will be inaccessible after installation.

Power input — Connect the included 12 VDC external power supply into the 2-pole, 3.5 mm captive screw connector. Be careful to observe the correct polarity.

Power Supply

Output Cord

SECTION A–A

Ridges

Smooth

Video output — BNC connectors for RGBHV output.

2-7

P/2 DA2 WM/EC/D/AAP Series • Controls and Installation

2-8

Controls and Installation, cont’d

Power up all of the input and output devices.

The image should now display on screen. If it does not, double check steps 3 through 6 and make adjustments as needed. Refer to the section “Setting the DIP switches” in this chapter.

For the P/2 DA2 WM F, attach the P/2 DA2 WM F to the wall mounting bracket (see “Installing the mud ring bracket”).

For the P/2 DA2 WM EC F, attach the P/2 DA2 WM F EC to the Euro Channel (see “P/2 DA2 WM EC F Euro Channel installation”).

Installing the mud ring bracket

1. Once the proper wall location for mounting the

distribution amplifier has been determined, cut an opening in the wall using the proper mounting template found in the appendix.

2. Carefully cut away the mounting surface material inside

the traced template lines.

3. Test the fit of the mud ring. The doglegs should fit easily

into the hole and the flat portion should rest flush against the wall. See the note in the following illustration.

4. Rotate all doglegs inward.

5. Insert the mud ring into the hole.

6. Tighten all of the dogleg screws until the doglegs clamp

the mud ring to the mounting surface. Do not overtighten.

Standard mud rings only: If you are going to screw the mud ring to the surface, rather than using the detachable doglegs, mark the four surface mounting screw holes at the corners of the mud ring.

Rotate doglegs and insert mud

ring into wall opening.

Extron MR 200D

Modular Mud Ring

Surface Mounting

Hole

Dogleg Screw

Equipment Mounting Holes

NOTE Do not disassemble the dogleg

from the dogleg screw. Rotate the dogleg out of the way to insert the mud ring into the wall.

Installing a mud ring bracket

2-9

P/2 DA2 WM/EC/D/AAP Series • Controls and Installation

2-11

Controls and Installation, cont’d

Connecting audio output

Before connecting audio output, determine whether your audio system is unbalanced or balanced. Then, follow the instructions below to connect unbalanced audio, or the instructions for “Balanced audio” to connect balanced audio.

C Wiring the audio incorrectly may damage the audio

output circuits.

Unbalanced audio

To attach the P/2 DA2 WM F/EC F to an unbalanced audio system, do the following:

1. Attach the audio cable to an unbalanced speaker input

connector (tip and sleeve).

2. Attach the audio cable to the audio cable connector (Extron

part number 10-319-10). Fasten the captive screws inside the audio cable connector.

Fastening captive screws

3. Slide the audio cable connector into the audio output

connector on the interface.

Tip (+)

Sleeve ( )

Unbalanced Output

Left

Tip

Sleeve(s)

NO Ground Here

Tip

Right

CAUTION

For unbalanced audio, connect the sleeve(s) to the ground contact.

DO NOT connect the sleeve(s) to the

negative (-) contacts.

Cabling

The P/2 DA2 WM F cabling diagram below shows how to connect input and output devices to the distribution amplifier’s front panel. The P/2 DA2 WM EC F model has identical connectors.

AUTO POWER

100%

UNITY

50%

GAIN/PEAKING

P/2 DA2 WM F cabling

1. Connect your display device to the 15-pin HD female

video output VGA connector on the rear of the P/2 DA2 WM F/EC F.

2. For audio output, refer to the section “Connecting audio

output” and connect the audio output cable to the 3.5 mm captive screw connector on the rear of the P/2 DA2 WM F/EC F.

3. Connect the power input cable to the rear power input

connector of the P/2 DA2 WM F/EC F.

4. Connect the computer’s video cable to the 15-pin HD

female input cable on the distribution amplifier’s faceplate.

5. If a local monitor is being used, connect the monitor to the

15-pin HD female buffered local monitor output on the faceplate.

6. For audio input, connect the input device into the front

faceplate’s 3.5 mm female audio jack.

2-10

P/2 DA2 WM/EC/D/AAP Series • Controls and Installation

2-13

Controls and Installation, cont’d

#4-40 Nut w/ Captive Washer

P/2 DA2 WM F AAP EC (up to 3 plates)

P/2 DA2 WM F AAP (up to 4 plates)

Adapter Plate

INPUT

AUTO POWER

ID PIN 4

UNITY

GAIN/PEAKING

100%

50%

ID PIN 11

AUDIO

BUFFERED

LOCAL MONITOR

P/2 DA2 WM F AAP

AUTO POWER

P/2 DA2 WM F AAP EC

ID PINS

100%

UNITY

50%

GAIN/

PEAKING

Installing adapter plates

2. Attach the output cables to the back side of the adapter

plate. Some adapter plates may require that conductors be soldered to the connectors. Attach foil and braided shields to ground connections.

Balanced audio

To attach the distribution amplifier to a balanced audio system, do the following:

1. Attach the audio cable to a balanced speaker input

connector (tip, ring, and sleeve).

2. Attach the audio cable to the audio cable connector (Extron

part number 10-319-10). Fasten the captive screws inside the audio cable connector as shown below.

3. Slide the audio cable connector into the audio output

connector on the distribution amplifier.

Installing architectural adapter plates

The P/2 DA2 WM F AAP may have up to four optional adapter plates and the P/2 DA2 WM F AAP EC can have up to three adapter plates. The adapter plates provide a convenient method of adding various connectors for specific audio and video requirements. The adapter plates must be ordered separately and must be attached to the faceplate and cabled before attaching the WM F AAP model to the wall mount bracket or the EC F AAP model to the Euro Channel.

1. Insert the adapter plate captive screws through the front

faceplate holes. Secure the adapter plate using the supplied washers and nuts.

2-12

Sleeve ( )

Ring (R)

Tip (L)

Tip

Sleeve(s)

Ring

Tip

Left

Right

Balanced Output

P/2 DA2 WM/EC/D/AAP Series • Controls and Installation

Controls and Installation, cont’d

2-15

P/2 DA2 WM EC F Euro Channel installation

Once the input and output cables have been connected and tested on the P/2 DA2 WM F EC, the distribution amplifier can be easily installed in the Euro Channel.

Euro Channel installation

Setting the DIP switches

Two sliding-type DIP switches can be found on the faceplate of the P/2 DA2 WM F/EC F.

To set the sliding-type DIP switches, slide the switch to the on/closed or off/open position.

The two DIP switches provide proper ID bit termination for a laptop computer that is not attached to a local monitor.

ID Pin 4 & ID Pin 11

ON — Set both pins to On if you are using the P/2 DA2

WM F/EC F with a laptop computer that is not attached to a local monitor.

OFF — Set both pins to Off if you are attaching a local

monitor to the P/2 DA2 WM F/EC F.

ID PIN 4 ID PIN 11

INPUT

AUTO POW

ID PINS

IT Y

GAIN/

PEAKING

1 00

5 0

AUDIO

BUFFERED LOCAL MONITOR

WITH ADSP

INPUT

AUTO POW

ID PINS

GAIN/

PEAKING

AUDIO

BUFFERED LOCAL MONITOR

WITH ADSP

P/2 DA2 WM F EC

Euro Channel

P/2 DA2 W

M F EC

P/2 DA2 WM F

INPUT

AUTO POWER

ID PIN 4

UNITY

GAIN/PEAKING

100%

50%

ID PIN 11

AUDIO

BUFFERED

LOCAL MONITOR

VGA Connector

Power (3.5 mm

Captive Screw Connector)

Do not remove unless faceplate is removed from wall.

Rear Cover Screws

Audio (3.5 mm

Captive Screw Connector)

Positive

Negative

N/C

P/2 DA2 WM F wall mount installation

Once the input and output cables have been connected and the P/2 DA2 WM F has been successfully tested, the faceplate may be attached to the mounting bracket using the four supplied screws.

N The center pole of the power input connector contains no

conductor. Connect the conductors to the two outer poles only, exactly as shown here.

Wall mounting the P/2 DA2 WM F

2-14

P/2 DA2 WM/EC/D/AAP Series • Controls and Installation

2-17

Controls and Installation, cont’d

Installing the P/2 DA2 D

The P/2 DA2 D is a wall-mounted product and can be mounted into an electrical wall box. These instructions include site preparation, wall box installation, and the mounting of the distribution amplifier in the wall box.

N The P/2 DA2 D must be installed into an Underwriters

Laboratories (UL) approved electrical wall box. The box is not included with the distribution amplifier; the installer is responsible for obtaining/installing the box.

Preparing the site and installing the wall box

Choose a location that allows cable runs without interference. Allow enough depth for both the wall box and the cables. You may need to install the cables into the wall or conduits before installing the distribution amplifier.

The distribution amplifier can be installed in a standard onegang electrical wall box. The installation must conform to national and local electrical codes. A dimensional drawing and a cutout template of the distribution amplifier are provided in appendix A of this manual.

N The cutout template of the P/2 DA2 D shown in

appendix A is not full size. Pay attention to the measurements shown in the template.

1. Mark the guidelines for the opening on the wall.

• If the distribution amplifier will be installed in a wall box, place the box against the installation surface and draw a line on it around the outside of the box.

• If the distribution amplifier will be installed without a wall box (fastening it directly to the wall), measure and mark the surface for the cutout area indicated in the cutout template.

2. Cut out the material from the marked area.

3. Check the opening size by inserting the wall box (if used)

or the distribution amplifier (if no box is used) into the opening. Enlarge or smooth the edges of the opening if needed.

4. Feed the cables through the wall box punch-out holes, and

secure them with cable clamps to provide strain relief.

5. Insert the wall box into the opening, and attach it to the

wall or stud using nails or screws. The front edge should be flush with the outer wall surface. See the following illustration.

Setting the internal jumpers

The jumpers (J2 and J6) inside the distribution amplifier are set at the factory for output to a local monitor. However, you can direct output to a data display by resetting the jumpers. Follow these steps and the illustration below to change the jumper settings. In some instances where DDC communication is required between the display device and the computer’s graphics card, pins 15 (J2) and 12 (J6) will carry that information.

C Changes to internal jumper settings must be

performed only by authorized service personnel.

1. Disconnect the power cable, then disconnect the output

and audio cables from the rear panel of the distribution amplifier. Next, remove the rear cover by removing the two front panel screws. See “P/2 DA2 F wall mount installation” in this chapter for screw locations.

2. Using a pair of tweezers or needle-nosed pliers, set

jumpers J2 and J6, as shown below in figure 2-10.

C Be sure you are electrically grounded before

touching any circuit board components.

• Connect pins 1 and 2 on both jumpers (factory default) to output to the 15-pin female local monitor connector on the front panel.

• Connect pins 2 and 3 on both jumpers to output to the rear 15-pin female output.

ID Pin Pass Through Jumpers

P/2 DA2 WM F Rear View

(cover removed)

1-2 = Local Monitor (default) 2-3 = Data Display

Setting the internal jumpers

3. Replace the rear cover and reconnect the output cable.

Reconnect the power and/or audio cables.

2-16

P/2 DA2 WM/EC/D/AAP Series • Controls and Installation

2-19

Controls and Installation, cont’d

3. Mount the distribution amplifier to the wall box with

machine screws, as shown in the following illustration.

Mounting the distribution amplifier to the wall box

4. Attach the Decora cover plate to the line driver, as shown

in the previous illustration.

5. Reconnect the power supply and restore power to the

equipment.

Wall opening

is flush with

edge of box.

Wall Box

Extron P2 DA2 D

AUDIO IN

COMPUTER IN

MONITOR OUT

Decora

Faceplate

Attaching the wall box to a wall stud

If attaching the wall box to wood, use four #8 or #10 screws or 10-penny nails. A minimum of 1/2 inch (1.3 cm) of screw threads must penetrate the wood.

If attaching the wall box to metal studs, use four #8 or #10 selftapping sheet metal screws or machine bolts with matching nuts.

Mounting the distribution amplifier

Before mounting the distribution amplifier and if it has not already been tested, test the system to make sure that the connections and settings are correct.

If the system is operating correctly, the distribution amplifier can be installed in the wall. Adjust the gain and set the DIP switches before fastening the distribution amplifier into the wall box. The controls and cables will be inaccessible after installation. See “Rear Panel Features and Operation” in this chapter for details about settings and adjustments.

Continue mounting the distribution amplifier by following the steps below.

1. Remove power from the distribution amplifier by

disconnecting the power supply.

2. Place the distribution amplifier through the opening in the

wall and into the wall box. Take care not to damage the output cable(s), which fit behind the distribution amplifier at the back of the wall box.

Installation Cable

Cable Clamp

Wall Stud

Installation Cable

Cable Clamp

Wall Stud

Screws or NailsScrews or Nails

2-18

P/2 DA2 WM/EC/D/AAP Series • Controls and Installation P/2 DA2 WM Series, EC, & D

Operation

Appendix A

Specifications, Dimensions,

Parts, and Templates

Specifications

Dimensions

Parts and Accessories

Templates

P/2 DA2 WM/EC/D/AAP Series

COMP

UTE

R IN

MONIT

OUT

AUDI

O IN

Projector

Extron MHR-5 Cable

PC w/ Audio

Extron P/2 DA2 D

Distribution Amplifier

Audio

Audio Output

Extron MPA 122

Mini Power Amplifier

POW

12V 3A MA

UTP

UTS

4/8 Ohms SPEAKERS

INPUT

REMO

10V VOL/MUTE

MPA

122

Extron SI 3CT LP

Full-Range Ceiling Speakers

Replacing the faceplate

The front faceplate is replaced by removing the two rear panel mounting screws, replacing the faceplate, then reattaching the two screws, as shown below.

P/2 DA2 D application example

An example of the P/2 DA2 D installation is shown below.

Faceplate (rear)

Back Panel

Mounting Screws

1 2 3 4

12 V

0.2 A MAX POWER

AUDIO

OUTPUT

CONFIG

VIDEO

OUTPUT

P/2 DA2 D

ON 1 2 3 4

1 2 3 4

33-1663-01 A 05 08

CONFIG Switches

SW 1= Local Monitor

ON= Present, OFF= Not Present

SW 2= Audio Ouput Config

ON= Stereo, OFF= Dual MONO

SW 3= SYNC Input Impedance

ON= 510 Ohm,

OFF= 10 kOhm

SW 4= Spare

Extron Electronics

Anaheim, CA

VIDEO

GAIN

NORM

MED

HIGH

N15779

2-20

Controls and Installation, cont’d

P/2 DA2 WM/EC/D/AAP Series • Appendix P/2 DA2 WM/EC/D/AAP Series • Appendix

A-3

Video output

Number/signal type

P/2 DA2 D ........................ 1 VGA–QXGA RGBHV, RGBS, RGsB,

RsGsBs, HDTV component video main output 1 VGA–QXGA RGBHV, RGBS, RGsB, RsGsBs, HDTV component video local monitor output

P/2 DA2 WM F, P/2 DA2 WM F AAP

2 VGA-UXGA RGBHV, RGBS, RGsB, RsGsBs, HDTV component video (with adapter)

Connectors

P/2 DA2 D

Main output .............. 5 female BNC on 3" pigtails

Local monitor ........... 1 female 15-pin HD

P/2 DA2 WM F, P/2 DA2 WM F AAP

(2) 15-pin HD female (1 display, 1 local monitor)

Nominal level ............................... 1.0 Vp-p for Y of component video

0.7 Vp-p for RGB and for R-Y and B-Y of

component video

Minimum/maximum levels....... Analog: 0.4 V to 1.4 Vp-p (follows input)

Impedance .................................... 75 ohms

Return loss (P/2 DA2 D) ............. <-38 dB @ 5 MHzP/2 DA2 WM F,

P/2 DA2 WM F AAP<-40 dB @ 5 MHz

DC offset (P/2 DA2 D)................ ±5 mV with input at 0 offset

Sync

Input type ..................................... RGBHV, RGBS, RGsB, RsGsBs, bi-level and

tri-level component video sync

Output type .................................. RGBHV, RGBS, RGsB, RsGsBs, bi-level and

tri-level component video sync

Input level ..................................... 3.0 V to 5.0 Vp-p

Output level .................................. 0.3 Vp-p for component video (bi-level

sync)

0.6 Vp-p for component video (tri-level

sync)

TTL: 5.0 Vp-p, unterminated for RGBHV,

RGBS

Input impedance .......................... 510 ohms or 10k ohm, switch selectable

A-2

Specifications, Dimensions, and Parts

Specifications

Video

Gain

P/2 DA2 D ........................ Main output: 0 dB, 0.6 dB, 1.2 dB,

selectable Local monitor output: unity

P/2 DA2 WM F, P/2 DA2 WM F AAP

Switchable: 0 dB, +1.2 dB, +2.2 dB(0.7 V,

0.8 V, or 0.9 V when input is 0.7 V and the gain/peaking switch is set to Unity, 50%, or 100%, respectively)

Bandwidth

P/2 DA2 D ........................ 350 MHz (-3 dB)

P/2 DA2 WM F, P/2 DA2 WM F AAP

300 MHz (-3 dB)

N ID bits can be terminated (pins 4 and 11) via a switch setting.

Video input

Number/signal type

P/2 DA2 D ........................ 1 VGA–QXGA RGBHV, RGBS, RGsB,

RsGsBs, HDTV component video

P/2 DA2 WM F, P/2 DA2 WM F AAP

1 VGA-UXGA RGBHV, RGBS, RGsB,

RsGsBs, HDTV component video

Connectors ................................... (1) female 15-pin HD

Nominal level ............................... 1.0 Vp-p for Y of component video

0.7 Vp-p for RGB and for R-Y and B-Y of

component video

Minimum/maximum levels ....... Analog: 0.4 V to 1.4 Vp-p with no offset at

unity gain

Impedance .................................... 75 ohms

Horizontal frequency .................. 15 kHz to 135 kHz

Vertical frequency ....................... 30 Hz to 170 Hz

Return loss .................................... <-38 dB @ 5 MHz

DC offset (max. allowable)

P/2 DA2 D ........................ ±5 mV

P/2 DA2 WM F, P/2 DA2 WM F AAP

200 mV

Input coupling (P/2 DA2 D) ....... DC

P/2 DA2 WM/EC/D/AAP Series • Appendix P/2 DA2 WM/EC/D/AAP Series • Appendix

Audio output

Number/signal type

P/2 DA2 D ........................ 1 stereo or dual mono (switch selectable),

balanced/unbalanced

P/2 DA2 WM F, P/2 DA2 WM F AAP

1 stereo, balanced/unbalanced

Connectors ................................... (1) 3.5 mm direct insertion captive screw

connector, 5 pole

Impedance .................................... 50 ohms unbalanced, 100 ohms balanced

Gain error (P/2 DA2 D) .............. ±0.5 dB channel to channel

Maximum level (Hi-Z) ................ +15 dBu, balanced or unbalanced,

at 1% THD+N

Maximum level (600 ohm) ......... +9 dBm, balanced or unbalanced,

at 1% THD+N

General

External power supply................ 100 VAC to 240 VAC, 50/60 Hz, external;

to 12 VDC, 1 A (max.), regulated

Power input requirements .........

12 VDC, 0.2 A

Temperature/humidity .............. Storage: -40 to +158 °F (-40 to +70 °C) /

10% to 90%, noncondensing

Operating: +32 to +122 °F (0 to +50 °C) /

10% to 90%, noncondensing

Cooling .......................................... Convection, no vents

Mounting ...................................... Wall or furniture mountable

Enclosure type

P/2 DA2 D ........................ Metal faceplate and a plastic Decora

wall

plate

P/2 DA2 WM F, P/2 DA2 WM F AAP

Metal Enclosure dimensions

P/2 DA2 D

Faceplate ................... 2.6" H* x 1.3" W x 0.1" D

(6.6 cm H* x 3.3 cm W x 0.3 cm D)

(Fits the opening in a 1 gang Decora

faceplate. *Height is 3.8" [9.7 cm] including

mounting tabs.)

Buffer ......................... 2.7" H x 1.8" W x 0.75" D*

(6.9 cm H x 4.6 cm W x 1.9 cm D*)

(*Depth excludes BNC connectors and

cables.)

A-5

Output impedance

P/2 DA2 D ........................ 75 ohms

P/2 DA2 WM F, P/2 DA2 WM F AAP

40 ohms, typical

Max. propagation delay

P/2 DA2 D ........................ 60 ns

P/2 DA2 WM F, P/2 DA2 WM F AAP

18.8 ns

Max. rise/fall time ....................... 4 ns

Polarity .......................................... Positive or negative (follows input)

Audio

Gain................................................ Unbalanced output: 0 dB; balanced output:

+6 dB

Frequency response .................... 20 Hz to 20 kHz, ±0.05 dB

THD + Noise................................. 0.03% @ 1 kHz at nominal level

S/N ................................................ >90 dB at maximum output (unweighted)

Crosstalk (P/2 DA2 D) ................ <-80 dB @ 1 kHz

Stereo channel separation (P/2 DA2 D)

>80 dB @ 1 kHz

CMRR (P/2 DA2 D) ..................... >67 dB @ 20 Hz to 20 kHz

Audio input

Number/signal type ................... 1 stereo, unbalanced

Connectors ................................... (1) 3.5 mm mini stereo jack (tip, ring,

sleeve) Impedance

P/2 DA2 D ........................ >18k ohms unbalanced, DC coupled

P/2 DA2 WM F, P/2 DA2 WM F AAP

>5k ohms unbalanced, DC coupled

Nominal level ............................... -10 dBV (316 mVrms)

Maximum level

P/2 DA2 D ........................ +10 dBV, (unbalanced) at 1% THD+N

P/2 DA2 WM F, P/2 DA2 WM F AAP

+8.5 dBu (unbalanced) at 1% THD+N

N 0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV 2 dBu

Specifications, Dimensions, Parts, cont’d

A-4

P/2 DA2 WM/EC/D/AAP Series • Appendix P/2 DA2 WM/EC/D/AAP Series • Appendix

Dimensions

Dimensions of the P/2 DA2 WM F and its AAP version are provided here for those who wish to make their own customized faceplates. The following diagrams are not drawn to scale.

All dimensions are given in inches.

P/2 DA2 WM F faceplate dimensions

WM F model faceplate dimensions

A-7

DETAIL A

THRU

.120 THRU

HAND SAND TO 0.06" RADIUS AROUND THE TOP OF THESE EDGES.

DETAIL A

.210 THRU

P/2 DA2 WM F

Faceplate ................... 4.5” H x 4.6” W x 0.1” D

(11.4 cm H x 11.7 cm W x 0.3 cm D)

(2 gang)

Box ............................. 2.6” H x 3.7” W x 1.6” D

(6.6 cm H x 9.4 cm W x 4.1 cm D)

P/2 DA2 WM F AAP

Faceplate ................... 4.5” H x 8.3” W x 0.1” D

(11.4 cm H x 21.1 cm W x 0.3 cm D)

(4 gang)

Box ............................. 2.6” H x 3.7” W x 1.6” D

(6.6 cm H x 9.4 cm W x 4.1 cm D) Product weight

P/2 DA2 D ........................ 0.2 lbs (0.1 kg)

P/2 DA2 WM F ................ 0.4 lbs (0.2 kg)

P/2 DA2 WM F AAP ....... 0.6 lbs (0.3 kg)

Shipping weight ........................... 2 lb (1 kg)

Vibration ....................................... ISTA 1A in carton (International Safe

Transit Association)

Listings .......................................... UL, CUL

Regulatory compliance

Safety ................................. CE, C-tick, UL. CUL

EMI/EMC ......................... CE, FCC Class A, VCCI, C-tick, ICES

MTBF ............................................. 30,000 hours

Warranty ....................................... 3 years parts and labor

N All nominal levels are at ±10%.

N Specifications are subject to change without notice.

Specifications, Dimensions, and Parts, cont’d

A-6

P/2 DA2 WM/EC/D/AAP Series • Appendix P/2 DA2 WM/EC/D/AAP Series • Appendix

.0000 [0.000]

.000 [0.000]

1.700 [43.00]

2X 0.050 [1.270]

0.155 [3.937]

1.445 [36.703]

1.550 [39.370]

1.600 [40.640]

0.000 [0.000]

0.060 [1.524]

0.100 [2.540]

0.225 [5.715]

0.000 [0.000]

2.720 [70.000]

0.110 [2.794]

2.720 [69.088]

2.830 [71.882]

.060 [1.524]

.100 [2.540]

.600 [15.500]

Front View Side View

P/2 DA2 D faceplate dimensions

D model faceplate dimensions

A-9

Specifications, Dimensions, and Parts, cont’d

P/2 DA2 WM F AAP faceplate dimensions

WM F AAP model faceplate dimensions

A-8

P/2 DA2 WM/EC/D/AAP Series • Appendix P/2 DA2 WM/EC/D/AAP Series • Appendix

A-11

Optional architectural adapter plates

A variety of optional adapter plates for pass-through connections may be ordered for the P/2 DA2 WM F AAP and P/2 DA2 WM F AAP EC. See the figure below. The WM F AAP model can accommodate up to four adapter plates and the WM F AAP EC model can handle up to three adapter plates. The adapter plates come in one and two-high sizes.

The WM F AAP model may be configured as follows:

• 4 adapter plates of plate size one or

• 2 adapter plates of plate size two or

• 2 adapter plates of plate size one and one adapter plate of plate size two

The WM F AAP EC model may be configured as follows:

• 3 adapter plates of plate size one or

• 1 adapter plate of plate size two and 1 adapter plate of plate size one

Examples of adapter plates

The tables on following pages list the available adapter plates and distinguish between plates with a single type of connector (single type) or plates with more than one type of connector (multi type).

2 - BNC

Blank Plate (no connector)

Single Space

Double Space

Blank Plate (no connector)

5 - BNC (Double)

2 - RJ-11

2 - RCA to Solder Cups

3 - RCA to Solder Cups

2 - S-video

1 - D-9 Pass Through Connector

3 - BNC

Specifications, Dimensions, and Parts, cont’d

Parts and Accessories

Included Parts

The table below lists part numbers of the various models.

Cables

The table below lists various lengths of high resolution VGA cables which can be used with the P/2 DA2 WM F/WM F AAP/ EC F/D models.

A-10

Model Part number

P/2 DA2 WM F (black, white, 60-376- (-02, -03, -05) RAL9010 white)

P/2 DA2 EC F (RAL9010 white) 60-376-10 P/2 DA2 WM F AAP (black, white, 60-377- (-02, -03, -05)

RAL9010 white) P/2 DA2 WM EC F AAP (RAL9010 white) 60-377-10 P/2 DA2 D (black, white) 60-955- (-02, -03) User manual

Male-to-female VGA cables Part number

VGA 6’ MHR 26-238-01 VGA 3’ MHR A (with audio) 26-490-01 VGA 6’ MHR A (with audio) 26-490-02 VGA 12’ MHR A

(with audio) 26-490-03

VGA 25’ MHR A (with audio) 26-490-04 VGA 50’ MHR A (with audio) 26-490-05

MR Series mud ring brackets Part number

MR 100, 1-gang, black or white 70-519-12 or -13 MR 100D, 1-gang, Decora

, black 70-581-12

MR 200, 2-gang, black or white 70-519-22 or -23

Mud ring mounting brackets

The table below lists various mud ring mounting brackets.

P/2 DA2 WM/EC/D/AAP Series • Appendix P/2 DA2 WM/EC/D/AAP Series • Appendix

lerrabrotcennocF21elamefrotcennocFelamefrotcennocF690-0710-11-12-

elamefonohpoeret" s¼(2)

(2)

(1)

1elamefonohpoerets"¼slanimretgulredlos3790-0710-11-12-

elamefonohponom"¼ elamefonohponom"¼slanimretgulredlos2790-0720-21-22-

elamefoerets sinimmm5 .33elamefoeretsinimm m5.lanimretgulredlos3890-0710-11-12-

)elamefotelamef(11-JR22

elamef11-JRelamef11-JR 990-0710-11-12-

)elamefotelamef(54-JR22

elamef54-JRelamef54-JR001-0710-11-12-

)elamefotelamef(51-DH11elamefDHnip-51elamefDHnip-51101-0710-11-12-

)elamotelam(51-DH11

elamDHnip-51elamDHnip-51101-0720-21-22-

)elamefotelamef(9-D11elamefDnip-9 elamefDnip-9 201-0710-11-12-

)elamotelam(9-D11

elamDnip-9 elamDnip-9 201-0720-21-22-

elamefRLXnip-3elamefRLXnip-3slanimretgulredlos3301-0710-11-12-

elamefRLXnip-4elamefRLXnip-4slanimretgulredlos3301-0720-21-22-

elamefRLXnip-6elamefRLXnip-6slanimretgulredlos3301-0730-31-32-

NIDinimnip-6

)esuom/draobyek(

1elamefNIDinimnip-6elamefNIDinimnip-6401-0710-11-12-

elop5,mm5.3

lanimretwercsevitpac

elop5,mm5.3

lanimretwercsevitpac

spucredlos501-0710-11-12-

/hctiwserusolctcatnoc1

dnaem-wohsDEL

kcajinimoeretsmm5.3

dnahctiwserusolctcatnoc

kcajoeretsinimmm5.3

spucredlos601-0710-11-12-

A-13

Specifications, Dimensions, and Parts, cont’d

setalPretpadAlarutcetihcrArotcennoCepyTelgniS

noitpircsedetalpretpadA

etalP

ezis

tnorF

epytrotcennoc

raeR

epytrotcennoc

#traP yarG

kcalB etihW

1etalpknalB1.a.n .a.n 090-0710-11-12-

2etalpknalB2.a.n .a.n 090-0720-21-22-

)elamefotelamef(lerrabCNB21elamefCNBelamefCNB190-0710-11-12-

)elamefotelamef(lerrabCNB31

elamefCNBelamefCNB190-0720-21-22-

)elamefotelamef(lerrabCNB52elamefCNBelamefCNB190-0730-31-32-

spucredlosotelamefACR21

)kcalb/der(elamefACRslanimretgulredlos290-0710-11-12-

spucredlosotelamefACR31

)kcalb/der(elamefACRslanimretgulredlos290-0720-21-22-

lerrabelamefACR2

)elamefotelamef(

1)kcalb/der(elamefACRelamefACR390-0710-11-12-

lerrabelamefACR3

)elamefotelamef(

1)kcalb/der(elamefACRelamefACR390-0720-21-22-

lerrabCNBotACR2

)elamefotelamef(

1)kcalb/der(elamefACRelamefCNB490-0710-11-12-

lerrabCNBotACR3

)elamefotelamef(

1)kcalb/der(elamefACRelamefCNB490-0720-21-22-

lerraboediv-Sotoediv-S2

)elamefotelamef(

1elamefNIDinimnip-4elamefNIDinimnip-4590-0710-11-12-

A-12

P/2 DA2 WM/EC/D/AAP Series • Appendix P/2 DA2 WM/EC/D/AAP Series • Appendix

Templates

Use these templates as a guide for cutting the hole in the installation surface (wall or furniture).

N This templates for the P/2 DA2 WM F and the P/2 DA 2

WM F AAP are not full size.

Do not scale.

P/2 DA2 WM F mounting template

P/2 DA2 WM F

Cut-Out Template for Extron's

To install P/2 DA2 directly into furniture or wall, cut along this line.

Location of P/2 DA2

Wall Plate

SURFACE CUT-OUT AREA FOR FURNITURE MOUNT

4.50"

(11.43 cm)

TEMPLATE IS NOT FULL SIZE.

4.60" (11.68 cm)

2.68"

(6.80 cm)

3.58" (9.10 cm)

A-15

Specifications, Dimensions, and Parts, cont’d

setalPretpadAlarutcetihcrArotcennoCepyTitluM

noitpircsedetalpretpadA

etalP

ezis

tnorF

epytrotcennoc

raeR

epytrotcennoc

#traP yarG

kcalB etihW

elamefCNB1dnaelamefoediv-S11

dnaelamefNIDinimnip-4

elamefCNB

elamefNIDinimnip-4

elamefCNBdna

701-0710-20-30-

elamefACR3dnaelamefoediv-S12

dnaelamefNIDinimnip-4

elamefACR

elamefNIDinimnip-4

elamefACRdna

701-0720-21-22-

elamefACR2dnaelamefoediv-S11

dnaelamefNIDinimnip-4

elamefACR

elamefNIDinimnip-4

elamefACRdna

701-0730-31-32-

elamefACR2dnaelamefCNB11

dnaelamefCNB

elamefACR

dnaelamefCNB

elamefACR

801-0710-11-12-

dnaelamefCNB1

kcajoeretsinimmm5.3

(1)

dnaelamefCNB

kcajoeretsinimmm5.3

dnaelamefCNB

spucredlos3

801-0720-21-22-

dnaelamefACR1

kcajoeretsinimmm5.3

dnaelamefACR

kcajoeretsinimmm5.3

dnaelamefACR

spucredlos3

901-0710-20-30-

A-14

P/2 DA2 WM/EC/D/AAP Series • Appendix P/2 DA2 WM/EC/D/AAP Series • Appendix

P/2 DA2 WM F AAP

Cut-Out Template for Extron's

To install P/2 DA2 directly into furniture or wall, cut along this line.

Location of P/2 DA2

Wall Plate

SURFACE CUT-OUT

AREA FOR

FURNITURE MOUNT

4.50" (11.43 cm)

TEMPLATE IS NOT FULL SIZE.

2.68" (6.80 cm)

7.31"

(18.28 cm)

8.23"

(20.90 cm)

A-17

Specifications, Dimensions, and Parts, cont’d

A-16

P/2 DA2 D mounting template

4.50"

(11.43 cm)

2.79"

(7.09 cm)

1.88"

(4.78 cm)

2.80"

(7.11 cm)

P/2 DA2 D

Cut-Out Template for Extron's

SURFACE

CUT-OUT AREA

FOR

FURNITURE

MOUNT

To install Line Driver directly into furniture or wall, cut along this line.

Location of Line Driver

Wall Plate

TEMPLATE IS FULL SIZE.

Please measure the printed template before cutting.

P/2 DA2 WM F AAP mounting template

P/2 DA2 WM/EC/D/AAP Series • Appendix

Specifications, Dimensions, and Parts, cont’d

A-18

Extron electronics P/2 DA2 D, WM EC F, P/2 DA2 WM EC F AAP, P/2 DA2 EC F User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual