Extron Electronics MTP U R Setup Guide

MTP U R Series • Setup Guide

OUTPUTS

MONO AUDIO

AA

POWER

IMPORTANT:

Go to www.extron.com for the complete

user guide, installation instructions, and

specifications before connecting the

product to the power source.

DELAY

VID

R

Y/C

SELECT

G

YUV
RGB

ADJUST

B

RGB

PEAKING

LEVEL

MTP U R RSA SEQ

This card provides quick start instructions for an experienced installer to set up
and operate any of the MTP U R Series products.

AUDIO
RS-232

SIGNAL

Pre-installation — Jumper Settings

The MTP U R has three jumpers located on the main board. JMP1 is RS-232 directional communication,
and JMP2 and JMP3 are for vertical and horizontal sync (respectively). By default JMP1 is bidirectional;
JMP2 and JMP3 are negative sync.

Installation

Step 1 — Mounting

Turn off or disconnect all equipment power sources and mount the MTP U R as required.

Step 2 — Connect Input

Connect the RJ-45 cable from an MTP transmitter to the Input port on the MTP U R. Terminate the
cable as shown on the right, using the same standard (A or B) at both ends.

POWER

12V

0.5A MAX

CAT 7 INPUT

NOTE: If the input is labeled “CAT 7 Input”, only a CAT 7 cable should be used (that is, MTP C7 U R RSA SEQ model).

Step 3 — Connect Outputs

Attach the applicable output cables (video, audio, and RS-232), depending on the MTP U R model used.

• Composite video output connector — Connect to the single female BNC connector (VID) .

• S-video output connector — Connect to the 4-pin mini DIN connector (Y/C).

• Component video (MTP U R RSA SEQ model only) — Connect to the three female BNC

connectors (Y, R-Y, and B-Y).

• High resolution video output connector — Connect to the 15-pin HD connector (RGB).

• RS-232 connector — Connect a serial communications port to the upper 3.5 mm,

5-pole captive screw connector for bidirectional RS-232 communication (as shown).

• Audio connector (MTP U R RSA SEQ and MTP U R A models only) — Connect a suitable audio device

audio device to the lower 5-pole captive screw connector for mono audio output (as shown).

MONO AUDIO

Mono output 1+

1

Mono output 1-

Mono output 2+

2

Mono output 2-

Sleeve(s)

Balanced Output

Do not tin the wires!

Mono output 1

NO GROUND.

Sleeve(s)

Mono output 2

NO GROUND.

Unbalanced Output

Step 4 — Power

Plug the included external 12 VDC power supply into the 2-pole captive screw connector. Wire the
connector (see image a on the right).

Grounding guidelines

Extron MTP U R products can be adversely affected by electrostatic discharge (ESD) if they are not
grounded correctly.

To prevent malfunctions or product damage, an experienced installer can correctly ground an
Extron MTP U R product in either of two ways:

• Ground the power input port — Insert one end of the grounding wire to the negative or ground pin on

the power input connector (see image a on the right). Tie the other end of the wire to an earth ground.

• Ground the chassis — Use a connector hex nut as shown in image b the right. Tie the other end of

the wire to an earth ground.

If you have any questions about how to ground a product in a specic application, contact an Extron technical
support specialist.

1

2

RJ-45

Connector

Pins:

12345678

Insert Twisted
Pair Wires

R-Y

Connected RS-232

Device Pins

Receive

Transmit

Ground

a

Smooth

Default settings
(viewed from rear)

Pin

1

2

3

4

5

6

7

8

B-Y

Y

MTP/HDMI U R

SECTION A–A

Power Supply

Output Cord

b

JMP2

JMP3

T568A T568B

Wire color

White-green

Green

White-orange

Blue Blue

White-blue

Orange

White-brown

Brown

RGB

Tx
Rx

Gnd
Spare
Spare

Pins

Ridges

White-orange

Orange

White-green

White-blue

Green

White-brown

Brown

VID

Y/C

3/16"
(5 mm)
Max.

JMP1

Wire color

RS-232

Tx Rx

MONO AUDIO

1

12V
xA MAX

Rear
Panel

SPACE

Tie
Wrap

Ridges

Earth
Ground

2

MTP U R Series • Setup Guide

RGB

PEAKING

LEVEL

MTP U R RS SEQ

Extron

Extron

Step 5 — Input Signal Detection

Check the displayed output is correct. The MTP U R detects the input signal format, indicated by the front panel LEDs (VID, Y/C,
YUV, RGB), and differentiates between RS-232 and audio signals. The output is then made on the appropriate connector and
all other outputs are muted.

Step 6 — Peaking and Level

Image sharpness is adjusted with the Peaking Control. Increased peaking compensates for mid- and
high-frequency detail loss. Minimum setting (full counterclockwise) is zero peaking.

Image brightness is adjusted using the Level Control. View the image and adjust the control for the best image quality.

Step 7 — Skew Compensation

Pair skew can be measured with test equipment or by viewing a crosshatch test pattern. The SEQ receivers have built-in
skew compensation capabilities. Adjust the equalization as follows:

A. Zero the skew delay for red, green, and blue by using a Tweeker or small screwdriver to press and hold the Select

button for 3 seconds. When the Red, Green, and Blue LED’s all go out, release the Select button.

B. Use UTP cable test equipment or examine the displayed image to determine which video signal (red, green, or

blue) is shifted furthest to the right.

C. Adjust the furthest left video signal towards the right by using a Tweeker or screwdriver to press and release the

Select button until the LED for the left-shifted color lights.

D. Slowly rotate the Adjust control clockwise until the shifted color is properly aligned.

E. Repeat steps C and D to align the third color if needed.

SELECT

RGB

PEAKING

LEVEL

MTP U R RS SEQ

DELAY

R

G

ADJUST

B

MTPX 1616 Plus

MTP Matrix Switcher

CONTROL

LINK

RESET

ACT

8

Tx Rx

ETHERNET

Tx Rx

Tx Rx

5 6 7

8

LOCAL RS - 232

RS-232/RS-422

Tx Rx

REMOTE

Tx Rx

Tx Rx

OUTPUTS

Tx Rx

1 2 3 4

Tx Rx

1 2 3 4 5 6 7

9 10 11 12 13 14 15 16

INPUTS

15 16

RGB

LOCAL OUTPUTS

LOCAL

INPUT SELECT

1 2 3 4 5 6 7 8

ON

123 4

RJ - 45

3

RGB

1

LOCAL INPUTS

RGB

3

2

9 10 11 12 13 14

RGB

2

2

4

1

1

2

3

1

2

2

1

2

1

1

AUDIO INPUTS

R

INPUT

L

Extron
MTP T SV A

Tr ansmitter

OUTPUT

MTP T SV A

S-VIDEO

MAX

12V

0.5a

MTP T 15 HD A

PRE-PEAK

ON

OUTPUT

AUDIO

OFF

MONITOR

POWER

12V

INPUT

.5A MAX

Extron
MTP T 15HD A

DVD-RW/-R RECORDING

Precision Cinema Progressive

Tr ansmitter

DVD

Figure 1. Example of a Typical MTP U R Series Application

PC

MTP U R RS

OUTPUTS

2

MONO AUDIO

1

Universal Receiver

VID

Y/C

MTP U R RS

RGB

POWER

12V

0.5A MAX

INPUT

Extron
MTP U R A

OUTPUTS

2

MONO AUDIO
1

VID

Universal Receiver

Y/C

MTP U R A

RGB

POWER

12V

0.5A MAX

INPUT

Flat Panel
Display

Projector

Extron Headquarters
+800.633.9876 Inside USA/Canada Only

Extron USA - West Extron USA - East
+1.714.491.1500 +1.919.850.1000
+1.714.491.1517 FAX [phone] FAX

Extron Europe
+800.3987.6673
Inside Europe Only

+31.33.453.4040
+31.33.453.4050 FAX

Extron Asia
+800.7339.8766
Inside Asia Only

+65.6383.4400
+65.6383.4664 FAX

Extron Japan

+81.3.3511.7655
+81.3.3511.7656 FAX

Extron China
+4000.EXTRON
+4000.398766
Inside China Only

+86.21.3760.1568
+86.21.3760.1566
FAX

© 2013 Extron Electronics All rights reserved. www.extron.com

Extron
Middle East

+971.4.2991800
+971.4.2991880 FAX

Extron Korea

+82.2.3444.1571
+82.2.3444.1575 FAX

Extron India

1800.3070.3777
Inside India Only

+91-80-3055.3777
[phone]
FAX

68-1367-50

Rev. B

01 13