Extron electronics MTP 1500RL 15HD A SEQ User Manual

Download

User Guide

MTP 1500RL 15HD A SEQ

Extended Distance Twisted Pair Receiver

Twisted Pair

68-1554-01 Rev. B

01 12

Precautions

Safety Instructions • English

This symbol is intended to alert the user of important operating and maintenance (servicing) instructions in the literature provided with the equipment.

This symbol is intended to alert the user of the presence of uninsulated dangerous voltage within the product’s enclosure that may present a risk of electric shock.

Caution

Read Instructions • Read and understand all safety and operating instructions before using the equipment. Retain Instructions • The safety instructions should be kept for future reference. Follow Warnings • Follow all warnings and instructions marked on the equipment or in the user information. Avoid Attachments • Do not use tools or attachments that are not recommended by the equipment

manufacturer because they may be hazardous.

Consignes de Sécurité • Français

Ce symbole sert à avertir l’utilisateur que la documentation fournie avec le matériel contient des instructions importantes concernant l’exploitation et la maintenance (réparation).

Ce symbole sert à avertir l’utilisateur de la présence dans le boîtier de l’appareil de tensions dangereuses non isolées posant des risques d’électrocution.

Attention

Lire les instructions• Prendre connaissance de toutes les consignes de sécurité et d’exploitation avant d’utiliser

le matériel.

Conserver les instructions• Ranger les consignes de sécurité aﬁn de pouvoir les consulter à l’avenir. Respecter les avertissements • Observer tous les avertissements et consignes marqués sur le matériel ou

présentés dans la documentation utilisateur.

Eviter les pièces de xation • Ne pas utiliser de pièces de ﬁxation ni d’outils non recommandés par le fabricant

du matériel car cela risquerait de poser certains dangers.

Sicherheitsanleitungen • Deutsch

Dieses Symbol soll dem Benutzer in der im Lieferumfang enthaltenen Dokumentation besonders wichtige Hinweise zur Bedienung und Wartung (Instandhaltung) geben.

Dieses Symbol soll den Benutzer darauf aufmerksam machen, daß im Inneren des Gehäuses dieses Produktes gefährliche Spannungen, die nicht isoliert sind und die einen elektrischen Schock verursachen können, herrschen.

Achtung

Lesen der Anleitungen • Bevor Sie das Gerät zum ersten Mal verwenden, sollten Sie alle Sicherheits-und

Bedienungsanleitungen genau durchlesen und verstehen.

Aufbewahren der Anleitungen • Die Hinweise zur elektrischen Sicherheit des Produktes sollten Sie

aufbewahren, damit Sie im Bedarfsfall darauf zurückgreifen können.

Befolgen der Warnhinweise • Befolgen Sie alle Warnhinweise und Anleitungen auf dem Gerät oder in der

Benutzerdokumentation.

Keine Zusatzgeräte • Verwenden Sie keine Werkzeuge oder Zusatzgeräte, die nicht ausdrücklich vom Hersteller

empfohlen wurden, da diese eine Gefahrenquelle darstellen können.

Instrucciones de seguridad • Español

Este símbolo se utiliza para advertir al usuario sobre instrucciones importantes de operación y mantenimiento (o cambio de partes) que se desean destacar en el contenido de la documentación suministrada con los equipos.

Este símbolo se utiliza para advertir al usuario sobre la presencia de elementos con voltaje peligroso sin protección aislante, que puedan encontrarse dentro de la caja o alojamiento del producto, y que puedan representar riesgo de electrocución.

Precaucion

Leer las instrucciones • Leer y analizar todas las instrucciones de operación y seguridad, antes de usar el

equipo.

Conservar las instrucciones • Conservar las instrucciones de seguridad para futura consulta. Obedecer las advertencias • Todas las advertencias e instrucciones marcadas en el equipo o en la

documentación del usuario, deben ser obedecidas.

Evitar el uso de accesorios • No usar herramientas o accesorios que no sean especiﬁcamente recomendados

por el fabricante, ya que podrian implicar riesgos.

安全须知 • 中文

这个符号提示用户该设备用户手册中有重要的操作和维护说明。

这个符号警告用户该设备机壳内有暴露的危险电压，有触电危险。

注意

阅读说明书 • 用户使用该设备前必须阅读并理解所有安全和使用说明。保存说明书 • 用户应保存安全说明书以备将来使用。遵守警告 • 用户应遵守产品和用户指南上的所有安全和操作说明。避免追加 • 不要使用该产品厂商没有推荐的工具或追加设备，以避免危险。

Warning

Power sources • This equipment should be operated only from the power source indicated on the product. This

equipment is intended to be used with a main power system with a grounded (neutral) conductor. The third (grounding) pin is a safety feature, do not attempt to bypass or disable it.

Power disconnection • To remove power from the equipment safely, remove all power cords from the rear of the

equipment, or the desktop power module (if detachable), or from the power source receptacle (wall plug).

Power cord protection • Power cords should be routed so that they are not likely to be stepped on or pinched by

items placed upon or against them.

Servicing • Refer all servicing to qualiﬁed service personnel. There are no user-serviceable parts inside. To prevent

the risk of shock, do not attempt to service this equipment yourself because opening or removing covers may expose you to dangerous voltage or other hazards.

Slots and openings • If the equipment has slots or holes in the enclosure, these are provided to prevent

overheating of sensitive components inside. These openings must never be blocked by other objects.

Lithium battery • There is a danger of explosion if battery is incorrectly replaced. Replace it only with the same or

equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions.

Avertissement

Alimentations• Ne faire fonctionner ce matériel qu’avec la source d’alimentation indiquée sur l’appareil. Ce

matériel doit être utilisé avec une alimentation principale comportant un ﬁl de terre (neutre). Le troisième contact (de mise à la terre) constitue un dispositif de sécurité : n’essayez pas de la contourner ni de la désactiver.

Déconnexion de l’alimentation• Pour mettre le matériel hors tension sans danger, déconnectez tous les cordons

d’alimentation de l’arrière de l’appareil ou du module d’alimentation de bureau (s’il est amovible) ou encore de la prise secteur.

Protection du cordon d’alimentation • Acheminer les cordons d’alimentation de manière à ce que personne ne

risque de marcher dessus et à ce qu’ils ne soient pas écrasés ou pincés par des objets.

Réparation-maintenance • Faire exécuter toutes les interventions de réparation-maintenance par un technicien

qualiﬁé. Aucun des éléments internes ne peut être réparé par l’utilisateur. Aﬁn d’éviter tout danger d’électrocution, l’utilisateur ne doit pas essayer de procéder lui-même à ces opérations car l’ouverture ou le retrait des couvercles risquent de l’exposer à de hautes tensions et autres dangers.

Fentes et orices • Si le boîtier de l’appareil comporte des fentes ou des oriﬁces, ceux-ci servent à empêcher les

composants internes sensibles de surchauffer. Ces ouvertures ne doivent jamais être bloquées par des objets.

Lithium Batterie • Il a danger d’explosion s’ll y a remplacment incorrect de la batterie. Remplacer uniquement

avec une batterie du meme type ou d’un ype equivalent recommande par le constructeur. Mettre au reut les batteries usagees conformement aux instructions du fabricant.

Vorsicht

Stromquellen • Dieses Gerät sollte nur über die auf dem Produkt angegebene Stromquelle betrieben werden.

Dieses Gerät wurde für eine Verwendung mit einer Hauptstromleitung mit einem geerdeten (neutralen) Leiter konzipiert. Der dritte Kontakt ist für einen Erdanschluß, und stellt eine Sicherheitsfunktion dar. Diese sollte nicht umgangen oder außer Betrieb gesetzt werden.

Stromunterbrechung • Um das Gerät auf sichere Weise vom Netz zu trennen, sollten Sie alle Netzkabel aus der

Rückseite des Gerätes, aus der externen Stomversorgung (falls dies möglich ist) oder aus der Wandsteckdose

ziehen.

Schutz des Netzkabels • Netzkabel sollten stets so verlegt werden, daß sie nicht im Weg liegen und niemand

darauf treten kann oder Objekte darauf- oder unmittelbar dagegengestellt werden können.

Wartung • Alle Wartungsmaßnahmen sollten nur von qualiziertem Servicepersonal durchgeführt werden. Die

internen Komponenten des Gerätes sind wartungsfrei. Zur Vermeidung eines elektrischen Schocks versuchen Sie in keinem Fall, dieses Gerät selbst öffnen, da beim Entfernen der Abdeckungen die Gefahr eines elektrischen Schlags und/oder andere Gefahren bestehen.

Schlitze und Öffnungen • Wenn das Gerät Schlitze oder Löcher im Gehäuse aufweist, dienen diese zur

Vermeidung einer Überhitzung der empndlichen Teile im Inneren. Diese Öffnungen dürfen niemals von

anderen Objekten blockiert werden.

Litium-Batterie • Explosionsgefahr, falls die Batterie nicht richtig ersetzt wird. Ersetzen Sie verbrauchte Batterien nur

durch den gleichen oder einen vergleichbaren Batterietyp, der auch vom Hersteller empfohlen wird. Entsorgen Sie verbrauchte Batterien bitte gemäß den Herstelleranweisungen.

Advertencia

Alimentación eléctrica • Este equipo debe conectarse únicamente a la fuente/tipo de alimentación eléctrica

indicada en el mismo. La alimentación eléctrica de este equipo debe provenir de un sistema de distribución general con conductor neutro a tierra. La tercera pata (puesta a tierra) es una medida de seguridad, no puentearia ni eliminaria.

Desconexión de alimentación eléctrica • Para desconectar con seguridad la acometida de alimentación eléctrica

al equipo, desenchufar todos los cables de alimentación en el panel trasero del equipo, o desenchufar el módulo de alimentación (si fuera independiente), o desenchufar el cable del receptáculo de la pared.

Protección del cables de alimentación • Los cables de alimentación eléctrica se deben instalar en lugares donde

no sean pisados ni apretados por objetos que se puedan apoyar sobre ellos.

Reparaciones/mantenimiento • Solicitar siempre los servicios técnicos de personal calicado. En el interior no

hay partes a las que el usuario deba acceder. Para evitar riesgo de electrocución, no intentar personalmente la reparación/mantenimiento de este equipo, ya que al abrir o extraer las tapas puede quedar expuesto a voltajes peligrosos u otros riesgos.

Ranuras y aberturas • Si el equipo posee ranuras o oriﬁcios en su caja/alojamiento, es para evitar el

sobrecalientamiento de componentes internos sensibles. Estas aberturas nunca se deben obstruir con otros

objetos.

Batería de litio • Existe riesgo de explosión si esta batería se coloca en la posición incorrecta. Cambiar esta batería

únicamente con el mismo tipo (o su equivalente) recomendado por el fabricante. Desachar las baterías usadas

siguiendo las instrucciones del fabricante.

警告

电源 • 该设备只能使用产品上标明的电源。设备必须使用有地线的供电系统供电。第三条线（

地线）是安全设施，不能不用或跳过。

拔掉电源 • 为安全地从设备拔掉电源，请拔掉所有设备后或桌面电源的电源线，或任何接到市电

系统的电源线。

电源线保护 • 妥善布线，避免被踩踏，或重物挤压。维护 • 所有维修必须由认证的维修人员进行。设备内部没有用户可以更换的零件。为避免出现触

电危险不要自己试图打开设备盖子维修该设备。

通风孔 • 有些设备机壳上有通风槽或孔，它们是用来防止机内敏感元件过热。不要用任何东西

挡住通风孔。

锂电池 • 不正确的更换电池会有爆炸的危险。必须使用与厂家推荐的相同或相近型号的电池。按

照生产厂的建议处理废弃电池。

FCC Class A Notice

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including interference that may cause undesired operation.

The Class A limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his own expense.

NOTE: This unit was tested with shielded cables on the peripheral devices. Shielded cables must be used with the unit to ensure compliance with FCC emissions limits.

Conventions Used in this Guide

In this user guide, the following are used:

CAUTION: A caution indicates a potential hazard to equipment or data.

NOTE: A note draws attention to important information.

TIP: A tip provides a suggestion to make working with the application easier.

WARNING: A warning warns of things or actions that might cause injury, death, or

other severe consequences.

Commands are written in the fonts shown here:

^AR Merge Scene,,Op1 scene 1,1 ^B 51 ^W^C

[01] R 0004 00300 00400 00800 00600 [02] 35 [17] [03]

E X! *X1&* X2)* X2#* X2! CE}

NOTE: For commands and examples of computer or device responses mentioned

in this guide, the character “0” is used for the number zero and “O” represents the capital letter “o.”

Computer responses and directory paths that do not have variables are written in the font shown here:

Reply from 208.132.180.48: bytes=32 times=2ms TTL=32

C:\Program Files\Extron

Variables are written in slanted form as shown here:

ping xxx.xxx.xxx.xxx —t

SOH R Data STX Command ETB ETX

Selectable items, such as menu names, menu options, buttons, tabs, and ﬁeld names are written in the font shown here:

From the File menu, select New.

Click the OK button.

Trademarks

All trademarks mentioned in this guide are the properties of their respective owners.

Contents

Introduction............................................................ 1

MTP 1500RL 15HD A SEQ Description ................. 1

Features .......................................................... 1

Transmission Distance ..................................... 2

Installation and Setup .......................................... 4

Rear Panel Features ............................................. 4

Power Supply Wiring ....................................... 6

TP Cable Termination ...................................... 7

Operation ................................................................ 8

Front Panel Controls and Indicators ..................... 8

Peaking and Level Adjustment ............................ 9

Skew Delay Compensation................................ 10

SEQ receiver skew compensation .................. 10

PRELIMINARY

Reference Information ....................................... 11

Speciﬁcations .................................................... 11

Part Numbers and Accessories ........................... 13

Included Parts ............................................... 13

Optional Parts ............................................... 13

Mounting .............................................................. 14

Tabletop Placement ........................................... 14

Rack Mounting ................................................. 14

UL Guidelines for Rack Mounting .................. 14

Rack Mounting Procedure ............................. 15

Under-desk Mounting ....................................... 15

Through-desk Mounting ................................... 15

PRELIMINARY

MTP 1500RL 15HD A SEQ • Contents v

MTP 1500RL 15HD A SEQ • Contents vi

Introduction

This manual details the installation and operation of the Extron MTP 1500RL 15HD A SEQ

Twisted Pair receiver with audio and skew equalization

In this guide the following terms are used:

z “Transmitter” refers speciﬁcally to the MTP transmitter. z “Receiver” or “SEQ receiver” refers specically to the MTP 1500RL 15HD A SEQ receiver

with skew equalization.

MTP 1500RL 15HD A SEQ Description

The receiver is used for long distance distribution of RGB, component (bi-/tri-level), S-video,

or composite video and audio over twisted pair cables.

It is a half rack size twisted pair receiver that is fully compatible with all MTP transmitters,

distribution ampliers, matrix switchers and associated video accessories. When used with any of the Extron MTP transmitter models, the receiver can transmit video over extended or

standard distances.

The MTP 1500RL 15HD A SEQ receive signals up to 2048x1080, HD component video (up

to1080p), standard component, S-video, bi-level or tri-level component video, and high

resolution RGB video). This is done using an RJ-45 connection and over an Extron Enhanced

Skew-Free™ AV UTP cable, or over a Category (CAT) 5, 5e or CAT 6, shielded twisted pair

(STP), unshielded twisted pair (UTP), or foil shielded twisted pair (FTP) cable.

Features

The receiver outputs multiple RGB formats, composite video, S-video and component video on the 15-pin HD connector, according to the current DIP switch settings.

NOTE: The MTP 1500RL receiver cannot be used with VTT or TP transmitters.

The receiver ships with external desktop 12 V, 1 A power supply that accepts 100 to 240 VAC, 50 Hz to 60 Hz input.

z Receives high resolution video and mono audio signals 1,500 feet (450 meters) or more

over a single CAT 5-type cable

z Supports RGBHV, RGBS, RGsB, RsGsBs, component, S-video, and composite video z Compatible with HDTV component video, bi-level or tri-level sync z Separate continuously variable level and peaking controls z Buffered MTP loop-through for daisy-chaining up to eight receivers z Independent skew compensation adjustments for each color z Compatible with any Extron MTP transmitter z Low proﬁle, rack-mountable metal enclosure

MTP 1500RL 15HD A SEQ • Introduction 1

Transmission Distance

The maximum transmission distance is determined by the frequency and resolution of the transmitted signal. The table below shows the maximum transmission distances (in feet and

meters) and the transmitter Pre-peak switch positions using Extron Enhanced Skew-Free AV UTP cable or UTP CAT cable, terminated with RJ-45 connectors.

Transmission Distances in feet (meteres)

Video Format Pre-peak Off Pre-peak On Max Distance

Vid, S-vid, YUV <1300 (396) >1400 (427) 1500 (457) 640x480 <1300 (396) >1400 (427) 1500 (457) 800x600 <1300 (396) >1400 (427) 1500 (457)

1024x768 <1300 (396) >1400 (427) 1500 (457) 1280x960 <1300 (396) >1400 (427) 1500 (457) 1280x1024 <1300 (396) >1400 (427) 1500 (457) 1360x765 <1300 (396) >1400 (427) 1500 (457) 1365x768 <1300 (396) >1400 (427) 1500 (457) 1366x768 <1300 (396) >1400 (427) 1500 (457) 1440x960 <1300 (396) >1400 (427) 1500 (457) 1440x1050 <1300 (396) >1400 (427) 1500 (457) 1600x1200 <1300 (396) >1400 (427) 1500 (457) 1920x1200 <1000 (305) >1100 (335) 1200 (366) 2048x1080 <1000 (305) >1100 (335) 1200 (366) 720p <1300 (396) >1400 (427) 1500 (457) 1080i <1300 (396) >1400 (427) 1500 (457) 1080p <1300 (396) >1400 (427) 1500 (457)

NOTE: The maximum distance is deﬁned as the distance from the ﬁrst input signal

Transmission distance with more than one device before the MTP 1500RL 15HD A SEQ

Input

Source

source to the last output signal display, regardless of the number and type of devices between.

Transmission distance with one device before the MTP 1500RL 15HD A SEQ

1500 feet (457 m) maximum

Input

Source

VGA

cable

VGA

cable

MTP Tx

Device

MTP Tx

Device

cable

1500 feet (457 m) maximum

MTP RL Rx

cable

Device

MTP 1500RL

15HD A Device

cable

15HD A Device

MTP 1500RL

VGA

cable

VGA

cable

Display

Figure 1. Maximum Transmission Distances

NOTE: The transmitter and receiver are designed for and perform best with Extron

Enhanced Skew-Free AV cable terminated in accordance with the TIA/EIA T568A standard. CAT 5 cables are acceptable but less preferable. Using pre-terminated

and tested cables is also recommended. Cables terminated on-site should be tested before use to ensure that they comply with Category 5 speciﬁcations.

MTP 1500RL 15HD A SEQ • Introduction 2

MTP 1500RL 15HD A SEQ Application Diagram

Ext MTP

Tw with Loop

RGBHV

Audio

Extron MTP T 15HD A

Twisted Pair

MTP T 1 5HD A

PRE-PEAK

Transmitter

OUTPUT

AUDIO

OFF

MONITOR

POWER

12V

INPUT

.5A MAX

500’ (152 m) UTP Cable (CAT 5/5e/6)

Flat Panel Display

SPARE

END

VIDEO SOG CSYNC

V +

H +

AUDIO

MTP 1500RL 15HD A SEQ

MONO

L R

OUTPUT

BUFFERED OUTPUT

INPUT

MTP

POWER

1500RL 15HD A SEQ

ron

12V

1.0A MAX

isted Pair Receiver

-Through and Skew EQ

Audio

RGBHV

500’ (152 m) UTP Cable (CAT 5/5e/6)

Extron MTP 1500RL 15HD A SEQ

Twisted Pair Receiver with Loop-Through and Skew EQ

Figure 2. Typical MTP 1500RL 15HD A SEQ Application

Flat Panel Display

SPARE

END

VIDEO SOG CSYNC

V +

H +

AUDIO

MTP 1500RL 15HD A SEQ

MONO

L R

OUTPUT

BUFFERED OUTPUT

INPUT

MTP

POWER 12V

1.0A MAX

Audio

RGBHV

MTP 1500RL 15HD A SEQ • Introduction 3

Installation and Setup

This section describes how to connect applicable cables to the MTP 1500RL A SEQ receiver.

It covers:

z Rear Panel Features z Power Supply Wiring z TP Cable Termination

Rear Panel Features

Rear panel connectors and features for the MTP 1500RL A SEQ receiver is shown below.

INPUT

MTP

BUFFERED OUTPUT

MTP

POWER

12V

1A MAX

OUTPUT

AUDIO

MONO

H +

V +

CSYNC

SOG

VIDEO

END

MTP 1500RL 15HD A SEQ

SPARE

Figure 3. Rear Panel Features of the MTP 1500RL 15HD A SEQ

a Power connector — Plug the included external 12 VDC, 1 A, power supply into this

2-pole captive screw connector (see “Power Supply Wiring” section for wiring details).

CAUTIONS: • Always use a power supply supplied or specied by Extron. Use of an

unauthorized power supply voids all regulatory compliance certiﬁcation and may cause damage to the supply and the end product.

• Unless otherwise stated, the AC/DC adapters are not suitable for use in air handling spaces or in wall cavities.

• The installation must always be in accordance with the applicable

provisions of National Electrical Code ANSI/NFPA 70, article 75 and the Canadian Electrical Code part 1, section 16.

• The power supply must not be permanently ﬁxed to building structure or similar structure.

b Input connector — Connect one end of the twisted pair cable from an MTP transmitter

to this RJ-45 connector (see “TP Cable Termination” to wire the connector).

CAUTION: Do not connect these devices to a computer data or telecommunications

network.

c Buffered output connector — Connect up to 5 daisy-chained MTP receivers to

this RJ-45 connector.

NOTE: In a daisy-chain, the maximum distance from video source to display device

should not exceed 1500 feet.

MTP 1500RL 15HD A SEQ • Installation and Setup 4

d High resolution video output connector — Connect a projector or other high

resolution video device to this 15-pin HD connector for RGB output.

NOTE: See DIP switch settings for signal format output.

e Audio connector — Connect a suitable audio device to the 5-pole captive screw

connector for mono audio output.

MONO AUDIO

Do not tin the wires!

MONO AUDIO

Mono output 1

NO GROUND.

Sleeve(s)

Mono output 2

NO GROUND.

Unbalanced Output

CAUTION

For unbalanced audio, connect the sleeve(s) to the ground contact.

DO NOT connect the sleeve(s) to the negative (-) contacts.

Mono output 1+

Mono output 2+

Mono output 1-

Sleeve(s)

Mono output 2-

Balanced Output

Figure 4. Audio Connector Wiring

f Receiver DIP switches — Set these DIP switches for the applicable signal.

z H sync (H+) and V sync (V+) switches — Set these switches up for positive

sync or down for negative sync.

z Composite sync (CSync), Sync on green (SOG), and Video switches —

Set these switches as shown in the table below to output the indicated format.

Output Format C Sync SOG Video

RGBHV

RGBS

RGsB

Component video*

S-video

Composite video*

* Input video format must match.

= switch is down

= switch is up

< < < > < < < > < < < > < < > < < >

H +

V +

CSYNC

SOG

VIDEO

END

SPARE

z End unit switch — Set this switch up if either of the following is true:

z The receiver being conﬁgured is the only receiver connected to the transmitter. z The receiver being conﬁgured is the last receiver in a daisy-chained system.

MTP 1500RL 15HD A SEQ • Installation and Setup 5

Power Supply Wiring

1.0 A MAX

POWER

NOTE: This product is intended to be supplied by a UL Listed power supply and

Wire the supplied male power connector (plug) as in shown below.

12V

output rated at 12 VDC, 1 A.

Rear Panel Power Receptacle

DC Power Cord Captive Screw Connector

Smooth

3/16”

(5 mm) Max.

Ridges

SECTION A–A

2-Pole Captive Screw Connector

Ground +12 VDC

AC Power Cord

External Power Supply (12 VDC, 1 A )

Power Supply

Output Cord

Tie Wrap

Figure 5. Power Connector Wiring

NOTES: • The length of the exposed wires in the stripping process is critical.

The ideal length is 3/16 inches (5 mm). If it is longer, the exposed wires may touch one another, causing a short circuit between them. Any shorter and the wires could be easily pulled out even if tightly fastened by the captive screws.

• Do not tin the wires. Tinned wire does not hold its shape and can become loose over time.

CAUTION: Power supply voltage polarity is critical. Incorrect voltage polarity can

damage the power supply and the product. Identify the power cord negative lead by the ridges on the side of the cord.

To verify the polarity before connection, plug in the power supply with no load and check the output with a voltmeter.

WARNING: The two power cord wires must be kept separate while the power

As an alternative, an Extron PS 124 Universal 12 VDC Power Supply, part #60-1022-01, can power multiple MTPs or other Extron 12 VDC devices using only one AC power

connector..

supply is plugged in. Remove power before wiring.

MTP 1500RL 15HD A SEQ • Installation and Setup 6

TP Cable Termination

RJ-45 Connector

NOTE: RJ-45 termination must comply with TIA/EIA T568A or TIA/EIA T568B wiring

standards for all connections.

The gure below details the recommended termination of TP cables with RJ-45 connectors in accordance with the TIA/EIA T568A or TIA/EIA T568B wiring standards. Either standard

can be used with CAT 5 cable, but the same standard must be used on both ends of the cable.

Pin T568A Wire Color T568B Wire Color

Pins:

1 2 3 4 5 6 7 8

White-green White-orange

Green Orange

White-orange White-green

Blue Blue

White-blue White-blue

Orange Green

White-brown White-brown

Brown Brown

12345678

Insert Twisted

Pair Wires

Figure 6. TP Cable Termination

NOTES: • Enhanced Skew-free AV cable is not recommended for Ethernet/LAN

applications.

• DO NOT connect the RJ-45 input to LAN, Ethernet, outside plant communications, or any telecommunications networks

• This cable is specially designed for compatibility with Extron Twisted Pair products that are wired using the TIA/EIA T568A standard.

The table below shows the MTP RJ-45 pin assignments for audio and video signals.

Pin RGBHV RGBS Composite S-Video Component

1 Red/V sync + Red + No Signal Chroma + R-Y +

2 Red/V sync - Red - No Signal Chroma - R-Y -

3 Mono Audio+ Mono Audio + Mono Audio + Mono Audio + Mono Audio +

4 Green + Green + Video + Luma + Y +

5 Green - Green - Video - Luma - Y -

6 Mono Audio - Mono Audio - Mono Audio - Mono Audio - Mono Audio -

7 Blue/H Sync + Blue/C Sync + No Signal No Signal B-Y +

8 Blue/H Sync - Blue/C Sync - No Signal No Signal B- Y -

Figure 7. MTP RJ-45 Pin Assignments

MTP 1500RL 15HD A SEQ • Installation and Setup 7

Operation

This section describes the operation details for the MTP 1500RL RS SEQ receiver. It covers:

z Front Panel Controls and Indicators z Peaking and Level Adjustment z Skew Delay Compensation

Front Panel Controls and Indicators

Front panel features on the MTP 1500RL 15HD A SEQ receiver are shown below.

SELECT

RED GREEN BLUE

DELAY

ADJUST

LEVEL

PEAKING

RGB

MIN/MAX

MTP 1500RL SERIES

Figure 8. MTP 1500RL 15HD A SEQ Receiver Front Panel

a Power LED — Indicates power is applied to the MTP. b Select button — This recessed button selects the red, green, or blue video signal to

adjust, and resets all them to a skew delay of zero nanoseconds. Press and release this button to cycle through and select the red, green, or blue video

signal for adjusting. The selected signal is indicated by the Red, Green, and Blue LEDs

(c).

Press and hold the button in for approximately 3 seconds to zero the skew delay for red,

green, and blue. The Red, Green, and Blue LEDs (d) all turn off. Release the button.

NOTE: The SEQ receiver automatically saves the setting for the video signal that is

being deselected when this button is pushed or when the selection times out after 10 seconds.

c Red, Green, and Blue LEDs — These LEDs indicate the video signal that is selected by

the Select button (b) for skew adjustment using the Adjust control (d). The LED for the selected color blinks when the skew compensation for the video signal of the selected color has reached the minimum or maximum limit.

MTP 1500RL 15HD A SEQ • Operation 8

d Adjust skew control — This control delays the selected red, green, or blue video signal

up to a maximum of 62 nanoseconds (ns), made in 2 ns incremental steps. Rotate the control counterclockwise to reduce the delay or clockwise to increase it (see “Skew

Delay Compensation” for details).

NOTES: • The movement of the adjustment control is smooth and does not have

mechanical steps or high- and low-limit stops.

• Watch the displayed image to observe the steps of delay.

• For best performance set the skew of the most delayed signal to 0 ns

(minimum) and adjust the other two signals to meet it.

e Level control — The Level control alters the video output voltage to affect the

brightness of the displayed image.

Adjust the knob while viewing the displayed image to set the level or boost that

provides the best picture quality (see “Peaking and Level Adjustment” section for details).

f Peaking control — Peaking affects the sharpness of a picture. Increased peaking can

compensate for mid- and high-frequency detail loss due to low bandwidth system components or capacitance in long cables.

Adjust this control while viewing the displayed image to obtain the optimum picture

sharpness. The LED lights red when the peaking is at the minimum (0) and maximum

(100%) peaking settings (see the “Peaking and Level Adjustment” section for details).

NOTE: To avoid possible video loss due to errors in the format detection, always

Peaking and Level Adjustment

For best performance and video format detection, the equalization of the MTP should be adjusted properly. To achieve this, do the following:

1. Terminate the green video signal output with a 75 ohm resistance, and measure the

video signal.

NOTE: • Set the gain adjustment so that a white ﬁeld video signal is +0.7

2. Using an alternating black and white pattern, adjust the peaking so that the video signal

matches that of the white ﬁeld video. This equalizes both the low frequency (white ﬁeld) and the high frequency (alternating black and white ﬁeld) to the same video level for best results.

Do not over-peak the signal.

start with minimal peaking and level, then increase values only as required.

volts from the ground level.

• Set the peaking adjustment using the highest frequency video

format signal for the system in RGB, component video, or S-video.

MTP 1500RL 15HD A SEQ • Operation 9

Skew Delay Compensation

CAT 5, 5e and CAT 6 cable can lead to registration errors between the red, green, and blue video signals. Pair skew can be measured with test equipment or identiﬁed by viewing a crosshatch test pattern to determine if either the red, green, or blue video image leads (appears to the left of) the other two video images.

NOTE: Unless the TP cable is changed, the skew adjustment should need to be

made only once, during installation

SEQ receiver skew compensation

The SEQ receivers have built-in skew compensation capabilities. Adjust the equalization as

follows:

1. Set the skew delay to zero for red, green, and blue as follows: a. Use a Tweeker or other small screwdriver to press and hold the Select button for

3 seconds. The Red, Green, and Blue LEDS all go out.

b. Release the Select button.

2. Use UTP cable test equipment or examine the displayed video image with a critical eye

to determine which video signal (red, green, or blue) is shifted furthest to the right.

NOTE: A crosshatch test pattern or a black background with vertical white lines is

ideal for determining skew.

3. Adjust the furthest left video signal as follows:

NOTE: The SEQ receiver cannot shift the furthest right video image to the left.

a. Use a Tweeker or other small screwdriver to press and release the Select button until

the LED for the left-shifted color (red, green, or blue) lights.

b. Slowly rotate the Adjust control clockwise while monitoring the display. Continue to

rotate the control until that color is properly converged.

NOTE: A 2ns adjustment is very ne. Up to 10ns of delay may be necessary before

a change in the display is detectable. The maximum delay possible is 62ns.

c. Use a Tweeker or other small screwdriver to press the Select button one more time

to save the most recent adjustment or allow the 10-second timeout to elapse.

4. If the remaining color is left shifted, repeat step 3.

MTP 1500RL 15HD A SEQ • Operation 10

Reference Information

This section provides information about:

z Speciﬁcations z Part Numbers and Accessories

Specications

Video

Gain ............................................... Unity

Number/signal type ........................ 1 set of proprietary analog signals

Connectors .................................... 1 female RJ-45

Video input — see MTP Series transmitters specications

Video output — receiver

Number/signal type ........................ 1 set of proprietary analog signals

1 analog RGBHV, RGBS, RGsB, RsGsBs, component video (bi- or tri-level sync), S-video, or

composite video

Connectors .................................... 1 female RJ-45

1 female 15-pin HD

Nominal level ................................. 1 V p-p for Y of component video and S-video, and for composite video

0.7 V p-p for RGB and for R-Y and B-Y of component video

0.3 V p-p for C of S-video

Minimum/maximum levels .............. 0.3 V to 1.45 V p-p

Impedance ..................................... 75 ohms

Return loss ..................................... <-30 dB @ 5 MHz

DC offset ....................................... <±35 mV with input at 0 offset

Skew compensation ....................... 62 ns

Maximum resolution ...................... Up to 1600x1200 and 1080p at 1500'; 1920x1200 and 2048x1080 at 1200'

Sync

Output type ................................... RGBHV, RGBS, RGsB, RsGsBs

Standards ....................................... NTSC 3.58, NTSC 4.43, PAL, SECAM

Output level ................................... 0.3 Vp-p for component video (bi-level sync)

0.6 Vp-p for component video (tri-level sync) TTL: 4.0 V to 5.0 V p-p, unterminated for RGBHV, RGBS

Output impedance ......................... 110 ohms

Polarity ........................................... Positive or negative (switch-selectable)

Audio

Number/signal type ........................ 1 set of proprietary analog signals

Connectors .................................... 1 female RJ-45

Gain ............................................... Unbalanced output: 0 dB; balanced output: +6 dB

Frequency response ........................ 20 Hz to 20 kHz, ±1 dB

THD + Noise ................................... 0.15% @ 1 kHz, 0.3% @ 20 kHz at nominal level

S/N ................................................. >70 dB at maximum output (unweighted)

Stereo channel separation .............. >60 dB @ 1 kHz

CMRR ............................................ >43 dB @ 20 Hz to 20 kHz

Audio input — See MTP Series transmitters specications

NOTE: 0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV ≈ 2 dBu

MTP 1500RL 15HD A SEQ • Reference Information 11

Audio output

Number/signal type ........................ 2 mono, balanced/unbalanced

Connectors .................................... (1) 3.5 mm captive screw connector, 5 pole

Impedance ..................................... 50 ohms unbalanced, 100 ohms balanced

Gain error ...................................... ±1 dB channel to channel

Nominal level ................................. +4 dBu (1.23 Vrms), -10 dBV (316 mVrms)

Maximum level ............................... +18 dBu, unbalanced at 1% THD+N

General

Recommended cable type .............. CAT 5/5e/6 (shielded or unshielded)

Power supply .................................. External

Input: 100-240 VAC, 50-60 Hz Output: 12 VDC, 1 A, 12 watts

Power input requirements .............. 12 VDC, 1.0 A max.

Temperature/humidity .................... Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing

Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%, noncondensing

Cooling .......................................... Convection, vents sides to top

Mounting

Rack mount ............................. Yes, with optional 1U rack shelf

Wall mount .............................. Yes, with optional wall mounting kit

Enclosure type ................................ Metal

Enclosure dimensions ..................... 1.0" H x 8.75" W x 6.0" D (half rack wide)

(2.5 cm H x 22.2 cm W x 15.2 cm D)

(Depth excludes connectors.)

Product weight ............................... 1 lb (0.5 kg)

Shipping weight ............................. 2 lbs (1 kg)

Vibration ........................................ ISTA 1A in carton (International Safe Transit Association)

Regulatory compliance

Safety ...................................... CE, c-UL, UL

EMI/EMC ................................. CE, C-tick, FCC Class A, ICES, VCCI

MTBF ............................................. 30,000 hours

Warranty ........................................ 3 years parts and labor

NOTE: All nominal levels are at ±10%.

NOTE: Speciﬁcations are subject to change without notice.

MTP 1500RL 15HD A SEQ • Reference Information 12

Part Numbers and Accessories

Included Parts

Description Part Number

MTP 1500RL 15HD A SEQ receiver 60-959-02 External, 12 VDC, 1A power supply PS 1210 C 70-775-01

3.5 mm, 3-pole captive screw connector for RS 232 connections

IEC power cord (1)

MTP 1500RL 15HD A SEQ Setup Guide

Optional Parts

These items can be ordered separately:

Description Part Number

Accessories

PS 124 multiple output 12 V power supply 60-1022-01 19" 1U Universal Rack Shelf 60-190-01 19" 1U Basic Rack Shelf 60-604-01

Enhanced Skew-Free™ AV cable

NOTE: Enhanced Skew-Free AV UTP cables are not recommended for Ethernet LAN applications.

Enhanced Skew-Free AV cable (cut, various lengths) 26-569-xx Enhanced Skew-Free AV 1000' (Bulk) (non-plenum) 22-141-03 Plenum enhanced Skew-Free AV 1000' (Bulk) 22-142-03

RJ-45 connectors

CAT 6 jack (black) 10-463-10 CAT 6 jack (red) 10-463-11 CAT 6 jack (blue) 10-463-12 CAT 6 jack (orange) 10-463-13 CAT 6 jack (gray) 10-463-14 CAT 6 jack (white) 10-463-15 CAT 6 jack (ivory) 10-463-16

MTP 1500RL 15HD A SEQ • Reference Information 13

Mounting

This section outlines the various mounting options available for the MTP 1500RL unit:

z Tabletop Placement z Rack Mounting z Under-desk Mounting z Through-desk Mounting

Tabletop Placement

Attach the four provided rubber feet to the bottom of the unit and place it in any convenient location.

Rack Mounting

UL Guidelines for Rack Mounting

The following Underwriters Laboratories (UL) guidelines are relevant to the safe installation of these products in a rack:

1. Elevated operating ambient temperature — If the unit is installed in a closed or

multi-unit rack assembly, the operating ambient temperature of the rack environment may be greater than room ambient temperature. Therefore, install the equipment in an environment compatible with the maximum ambient temperature (Tma: +122 °F, +50 °C) speciﬁed by Extron.

2. Reduced air ﬂow — Install the equipment in the rack so that the equipment gets

adequate air ﬂow for safe operation.

3. Mechanical loading — Mount the equipment in the rack so that uneven mechanical

loading does not create a hazardous condition.

4. Circuit overloading — Connect the equipment to the supply circuit and consider the

effect that circuit overloading might have on overcurrent protection and supply wiring. Appropriate consideration of the equipment nameplate ratings should be used when addressing this concern.

5. Reliable earthing (grounding) — Maintain reliable grounding of rack-mounted

equipment. Pay particular attention to supply connections other than direct connections to the branch circuit (such as the use of power strips).

MTP 1500RL 15HD A SEQ • Mounting 14

Rack Mounting Procedure

ws longer

The unit can be mounted on optional rack systems, including:

z RSU 129: 9.5 inch deep, 1U rack shelf kit (part number 60-190-01) z RSU 126: 6 inch deep, 1U rack shelf kit (part number 60-190-10)

To mount the device on a rack shelf

1. Remove the feet from the bottom of the MTP, if they are installed.

2. Mount the MTP using two 4-40 x 3/16 inch screws in opposite (diagonal) corners to

secure the MTP to the shelf.

NOTE: DO NOT stack units on top of one another as this may cause the units to

overheat.

3. Install false faceplates or other units to the rack shelf.

1U Universal Rack Shelf

Front false faceplate uses 2 screws.

1/2 Rack Width Front False Faceplate

Figure 9. Mounting the MTP on a Standard Shelf

Under-desk Mounting

Mount the unit under a desk or podium, using the optional Extron MBU 125 under-desk mounting kit (part number 70-077-01) by following the instructions provided with the kit.

Through-desk Mounting

Mount the unit through a desk or podium using the optional Extron MBD 129 through desk mounting kit (part number 70-077-02) by following the instructions provided with the kit.

Use 2 mounting holes on opposite corners.

(2) 4-40 x 3/16" Screws

NOTE: Using scre

than 3/16” will damage the unit and void the warranty.

MTP 1500RL 15HD A SEQ • Mounting 15

Extron Warranty

Extron Electronics warrants this product against defects in materials and workmanship for a period of three years from the date of purchase. In the event of malfunction during the warranty period attributable directly to faulty workmanship and/or materials, Extron Electronics will, at its option, repair or replace said products or components, to whatever extent it shall deem necessary to restore said product to proper operating condition, provided that it is returned within the warranty period, with proof of purchase and description of malfunction to:

USA, Canada, South America, and Central America:

Extron Electronics 1001 East Ball Road Anaheim, CA 92805 U.S.A.

Europe, Africa, and the Middle East:

Extron Europe Hanzeboulevard 10 3825 PH Amersfoort The Netherlands

Asia:

Extron Asia 135 Joo Seng Road, #04-01 PM Industrial Bldg. Singapore 368363

Japan:

Extron Electronics, Japan Kyodo Building, 16 Ichibancho Chiyoda-ku, Tokyo 102-0082 Japan

China:

Extron China 686 Ronghua Road Songjiang District Shanghai 201611 China

Middle East:

Extron Middle East Dubai Airport Free Zone F12, PO Box 293666 United Arab Emirates, Dubai

Singapore

This Limited Warranty does not apply if the fault has been caused by misuse, improper handling care, electrical or mechanical abuse, abnormal operating conditions, or if modiﬁcations were made to the product that were not authorized by Extron.

NOTE: If a product is defective, please call Extron and ask for an Application Engineer to receive an RA (Return

Authorization) number. This will begin the repair process.

USA: (714) 491-1500 Europe: 31.33.453.4040 Asia: 65.6383.4400 Japan: 81.3.3511.7655

Units must be returned insured, with shipping charges prepaid. If not insured, you assume the risk of loss or damage during shipment. Returned units must include the serial number and a description of the problem, as well as the name of the person to contact in case there are any questions.

Extron Electronics makes no further warranties either expressed or implied with respect to the product and its quality, performance, merchantability, or ﬁtness for any particular use. In no event will Extron Electronics be liable for direct, indirect, or consequential damages resulting from any defect in this product even if Extron Electronics has been advised of such damage.

Please note that laws vary from state to state and country to country, and that some provisions of this warranty may not apply to you.

Extron USA - West Headquarters

+800.633.9876 Inside USA/Canada Only

+1.714.491.1500

FAX:

+1.714.491.1517

Extron USA - East

+800.633.9876

Inside USA/Canada Only

+1.919.863.1794

FAX:

+1.919.863.1797

Extron Europe

+800.3987.6673

Inside Europe Only

+31.33.453.4040

FAX:

+31.33.453.4050

Extron Asia

+800.7339.8766

Inside Asia Only

+65.6383.4400

FAX:

+65.6383.4664

Extron Japan

+81.3.3511.7655

FAX:

+81.3.3511.7656

Extron China

+4000.EXTRON +4000.398766

Inside China Only

+86.21.3760.1568

FAX:

+86.21.3760.1566

Extron

Middle East

+971.4.2991800

FAX:

+971.4.2991880

Extron Korea

+82.2.3444.1571

Fax:

+82.2.3444.1575

Extron India

1800.3070.3777

Inside India Only

+91-80-3055.3777

Fax:

+91 80 3055 3737

Extron electronics MTP 1500RL 15HD A SEQ User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual