MediaLink™ Mounting Options Installation Guide
This guide details how to install the following Extron MediaLinkTM Mounting
Options faceplates, designed for use with an MLC 206 controller.
• MLM 206 LAAP, a 3.15" H x 10.00" W (8.0 cm H x 25.4 cm W) lectern/
furniture-mounting faceplate with four single-space AAP openings:
#60-389-02 (black), #60-389-03 (white), 60-389-05 (RAL9010 off-white)
DISPLAY
POWER
VOLUME
MAX
MIN
Extron
MLM 206 LAAP
This faceplate replaces the MLM-LAAP.
• MLM 206 7GWP, a seven-gang (4.50" H x 13.57" W [11.43 cm H x
34.46 cm W]) faceplate with eight single-space AAP openings. This plate can
be mounted to a mud ring, an Extron Surface Mount Box (#60-645-02 or -05),
an Extron External Wall Box (#60-689-02, -03, -05), or a standard electrical
box: #70-373-02 (black), #70-373-03 (white), #70-373-05 (RAL9010 off-white)
MediaLink
DISPLAY
POWER
VOLUME
MAX
MIN
Extron
MediaLink
MLM 206 7GWP
Controllers and AAPs are not included with any of the faceplates.
Replacing the MLC 206 Faceplate with an MLM Faceplate
1. Use a small Phillips screwdriver to remove the four faceplate attachment
screws marked
1
1
DISPLAY
POWER
VOLUME
MAX
MIN
Extron
in the picture below, and save them for later use.
1
1
VCR DVD Laptop
1
MLC 206
Do not remove these screws while the MLC 206 is installed in a wall or
furniture, or the controller may fall down into the wall/furniture or wall box.
68-621-01 Rev. F
01 05
1MediaLink™ Mounting Options • Installation Guide
MediaLink™ Mounting Options Installation Guide, cont’d
2. Lift the faceplate off the MLC 206.
Plastic Window
Faceplate
Templates
Extron
DISPLAY
POWER
VOLUME
MAX
MIN
MediaLink
Remove four screws.
3. Align the openings in the new MLM faceplate with the controller’s buttons,
knob, and LEDs, and place the new faceplate on the MLC, as shown above.
4. Replace the four screws removed in step one, and hand tighten them.
5. Install the MLC 206 MediaLink controller in a wall or furniture as
appropriate. If necessary, use one of the cutout templates in this guide to
create an opening in the installation surface of a lectern or other furniture.
Use the appropriate template on the next 2 pages as a guide to measure and mark
the hole in the wall or furniture for installing the faceplate with an MLC 206.
The templates are not to scale and are provided for reference only.
The controller requires a depth of at least 1.5" (3.8 cm) inside the wall or furniture.
MediaLink™ Mounting Options • Installation Guide2
3.15"
(8.0 cm)
2.9"
(7.4 cm)
10"
(25.4 cm)
8.9"
(22.6 cm)
SURFACE CUT-OUT
AREA FOR
FURNITURE MOUNT
Top Panel
Location of MLC 226
To install MLC 206
and MLM 206 LAAP
directly into furniture,
cut along this line.
.250" (1.00 cm)
.295" (1.16 cm)
TEMPLATE IS NOT FULL SIZE.
Cut-Out Template for Extron's MLM 206 LAAP
3MediaLink™ Mounting Options • Installation Guide
MLM 206 7GWP
4.5"
(11.4 cm)
2.9"
(7.4 cm)
Top Panel
13.57"
(34.46 cm)
12.9"
(32.77 cm)
SURFACE CUT-OUT
AREA FOR
FURNITURE MOUNT
TEMPLATE IS NOT FULL SIZE.
Cut-Out Template for Extron's MLM 206 7GWP
Location of MLC 206
To install MLC 206
and MLM 206 7GWP
directly into furniture,
cut along this line.
www.extron.com
4
Extron Electronics, USA
1230 South Lewis Street
Anaheim, CA 92805
USA
714.491.1500
Fax 714.491.1517
Extron Electronics, Europe
Beeldschermweg 6C
3821 AH Amersfoort
The Netherlands
+31.33.453.4040
Fax +31.33.453.4050
Extron Electronics, Asia
135 Joo Seng Road, #04-01
PM Industrial Building
Singapore 368363
+65.6383.4400
Fax +65.6383.4664
© 2005 Extron Electronics. All rights reserved.
Extron Electronics, Japan
Kyodo Building
16 Ichibancho
Chiyoda-ku, Tokyo 102-0082 Japan
+81.3.3511.7655
Fax +81.3.3511.7656
Loading...