Extron Electronics MBU 149 User Manual

Extron USA - West

Headquarters

+800.633.9876

Inside USA / Canada Only

+1.714.491.1500
+1.714.491.1517 FAX

Extron USA - East

+800.633.9876

Inside USA / Canada Only

+1.919.863.1794
+1.919.863.1797 FAX

Extron Europe

+800.3987.6673

Inside Europe Only

+31.33.453.4040
+31.33.453.4 050 FAX

Extron Asia

+800.7339.8766

Inside Asia Only

+65.6383.4400
+65.6383.4664 FAX

Extron Japan

+81.3.3511.7655
+81.3.3511.7656 FAX

Extron China

+400.883.1568

Inside China Only

+86.21.3760.1568
+86.21.3760.1566 FAX

Extron Middle East

+971.4.2991800
+971.4.2991880 FAX

Installation

#8 Screw
(4 Places)
Each Side

Mounting Screws
(2 Places)
Each Side

Mounting
Bracket

Step 1 — Attach brackets to device

Step 2 — Mark screw location

Step 3 — Drill holes

Setup Guide — MBU 149

The Extron® MBU 149 Under-Desk Mount Kit (part number
70-222-01) lets you attach an Extron 1U high device to the
underside of a desk or table, or to a wall. The brackets
extend approximately ¼" (6 mm) above the top surface of the
device, which allows an air space between the enclosure and
the mounting surface.

Attach brackets to the device with the supplied machine
screws, as shown on the left side of the picture below.

Hold the device with attached brackets against the
wall or the underside of the furniture, and
mark the screw hole locations (centers of
the brackets’ screw slots).

Drill four pilot
holes, each
3/32" (2 mm)
in diameter, ¼"
(6 mm) deep,
at the locations
marked in step 2.

(Continued on reverse side)

Setup Guide — MBU 149, cont’d

Extron USA - West

Headquarters

+800.633.9876

Inside USA / Canada Only

+1.714.491.1500
+1.714.491.1517 FAX

Extron USA - East

+800.633.9876

Inside USA / Canada Only

+1.919.863.1794
+1.919.863.1797 FAX

Extron Europe

+800.3987.6673

Inside Europe Only

+31.33.453.4040
+31.33.453.4 050 FAX

Extron Asia

+800.7339.8766

Inside Asia Only

+65.6383.4400
+65.6383.4664 FAX

Extron Japan

+81.3.3511.7655
+81.3.3511.7656 FAX

Extron China

+400.883.1568

Inside China Only

+86.21.3760.1568
+86.21.3760.1566 FAX

Extron Middle East

+971.4.2991800
+971.4.2991880 FAX

Step 4 — Install screws

Insert the wood screws (provided) into the pilot holes. Fasten each screw into the furniture or
wall until the screw heads protrude slightly less than ¼" (6 mm) from the mounting surface.

Step 5 — Align brackets with screws

Align the screws with the slots in the mounting brackets and place the device against the
surface, with the screw heads through the bracket slots.

Step 6 — Adjust and fasten

Slide the device slightly forward or back, then tighten all screws to fasten it to the furniture or
wall, as shown on the right side of the diagram on the front of this guide.

© 2009 Extron Electronics. All rights reserved.

68-704-01

Rev. B

09 09