Extron Electronics MAAP DVI-DL User Manual

MAAP DVI-DL Installation Guide

cable to three tabs.

The Extron MAAP DVI-DL is a triple-space mini architectural adapter plate (MAAP)
with a mounted 10-inch DVI pigtail and a 3.5 mm stereo jack with solder tabs.
The MAAP DVI-DL is compatible with DVI-DL (Dual Link D), DVI-I Single Link,
DVI-D (Digital only), and DVI-A (analog only). The MAAP DVI-DL provides the
following:

• One DVI-I computer video connector mounted on the plate

• One DVI-I connector on a 10-inch pigtail

• One 3.5 mm stereo audio mini barrel jack with solder tabs

• 55 mm (2.17 inches) minimum depth

N In North America, this product must be installed only in a UL-listed junction box, in accordance with the National

Electrical Code.

55 mm
(2.17”)

Installing the MAAP DVI-DL

The MAAP DVI-DL can be mounted to any Extron mounting product that accommodates three-space MAAP

DVI
Connector

products. It can also be installed in a 50 mm raceway; with the addition of MAAP 201 EU frame, the minimum
depth of 55 mm (2.17 inches) is met. (See the side view diagram at right.)

Cabling

DVI — Insert a male DVI-I (Dual Link or Single Link), DVI-D (Dual Link or Single Link),or DVI-A (analog only) cable into either or

both DVI connectors.

Audio — The tabs on the 3.5 mm mini audio jack can accept wire gauges up to

4 AWG. Solder the audio cable to the three tabs as described below and
illustrated at right.

Ring

(Right or –)

• For balanced mono audio: ring = –, tip = +, sleeve = ground

• For unbalanced stereo audio: ring = right, tip = left, sleeve = ground

N It is recommended that you remove the audio jack from the MAAP plate before

soldering to avoid getting solder on any other part of the MAAP. Replace the
connector after the wire is attached.

Solder the audio

Sleeve

(Ground)

68-1802-01 Rev. A 10 09

MAAP DVI-DL Installation Guide (Cont'd)

Installing on a Raceway 

1. Place the MAAP 201 frame in the front opening of the
raceway so that it rests against the back supports.

2. Turn the two screws on the bracket so that the doglegs rotate
behind the back support until they clamp securely to it. (See
the illustration at right.)

3. Place the plastic frame over the metal bracket in the opening
of the raceway and press the frame into place.

4. Thread the cables from the raceway out through the
mounting bracket and plastic frame and connect them to the
MAAP.

• Solder the audio cable to the barrel jack on the back of
the MAAP plate (see "Cabling" on the front side).

• Connect a DVI device cable to the DVI connector on the
pigtail.

N

To meet the 55 mm (2.17 inches) minimum depth

requirement, do not let the DVI cable overlap other
cables in the raceway.

MAAP 201EUC

Mounting Frame

MAAP DVI-DL

Adapter Plate

C

and audio cables within the raceway. Doing this will crowd
the MAAP cables, which could cause them to bend too
sharply and be damaged.

Plastic Frame

Do not place additional cables behind the MAAP's pigtail

Rotate (2) Doglegs
Inward

Tip

(Left or +)

5. Seat the MAAP plate in the plastic frame, aligning the four holes in the plate with the four holes in the metal mounting bracket.

6. Use the four provided hex screws to attach the MAAP plate to the metal bracket.

Included Parts Part number

MAAP DVI-DL with 10-inch pigtail

Black (US only)
White (US only)
RAL 9010 white

70-717-02
70-717-03
70-717-05

Included Parts

Hex wrench and four screws

Installation Guide

www.extron.com