Extron electronics KP 6 Keypad, KP 6 Remote User Manual

User’s Guide

Keypad Remote Controls

68-694-01 Rev. A

Printed in the USA

07 02

KP 6 Keypad Remote

Keypad Remote Controls • Installation and OperationKeypad Remote Controls • Installation and Operation

Installation and Operation

32

Introduction

The KP 6 is designed to control MSW 4 Series, SW AV Series (4 and 6
input models only), SW VGA/Ars Series, and SW RGBHV/ A Series
switchers, or other Extron products with contact closure ports or
ports labeled as “Remote.”

The KP 6 is a contact closure remote for selecting the switcher’s input.
When a number key is pressed, the wire associated with that input is
momentarily shorted to ground, making the switcher switch to that
input.

The KP 6 can control up to 6 inputs and requires no power.

Installation

Installation with a 9-pin D-sub connector

Many switchers, such as the SW6 VGA Ars Switcher, come equipped
with a 9-pin D-sub connector. To use the KP 6 Keypad Remote
Control on this type of switcher, install it as follows:

1. Power down the switcher.

2. Connect the KP 6 adapter’s 9-pin plug to the contact closure

connector on the switcher’s rear panel.

3. Position the KP 6 Keypad for the most convenient operation.

4. Power up the switcher.

Figure 1 — Typical KP 6 application (with 9-pin D­sub connector)

Figure 2 — 9-pin Sub-D connector pinout

Installation with a captive screw connector

Some switchers, such as the MSW 4 Series, are not equipped with
9-pin D-sub connectors and have a 3.5mm, 5-pole captive screw
connector (labeled “Contact”) instead. In order to use the KP 6
Keypad Remote Control with these switchers, a captive screw
connector (included with the switcher) must be used. To use a captive
screw connector, the existing 9-pin D-sub connector must be removed
from the cable and a captive screw connector installed.

To install the captive screw connector, remove the wire from the 9-pin
D-sub connector, then strip the wires and insert them into the new
connector (supplied with the switcher). Wire the connector as shown
here. Tighten the screws to secure the wires. Clip off the green and
blue wires.

Do not tin the stripped wire leads before installing the
captive screw connector. Tinned wires are not as secure
in the captive screw connectors and could pull out.

Install the KP 6 Keypad Remote Control on this type of switcher as
follows:

1. Rewire the connector on the KP 6 Keypad Remote Control.

2. Power down the switcher.

3. Connect the KP 6 adapter’s captive screw connector to the

“Contact” connector on the switcher’s rear panel.

4. Position the KP 6 Keypad for the most convenient operation.

5. Power up the switcher.

Brown

Red

Orange

Yellow

Black

4

3

2

1

25 foot
cable

KP 6 Keypad

Remote Control

SW6 VGA Ars Switcher

SW6 VGA Ars

REMOTE

100-240V 0.2A

INPUTS

1

2

3

4

5

50-60Hz

OUTPUT

OUTPUT

LR

SW6 VGA Ars

6

niP erusolctcatnoC n Wire coloroitcnuF

1

1#nI 1 Brown#tupnI

2

3

4

2#nI 2 Red#tupnI

5 dnG d BlacknuorglangiS

6

3#nI 3 Orange#tupnI

7

4#nI 4 Yellow#tupnI

8

5#nI 5 Green#tupnI

9

6#nI 6 Blue#tupnI

Not used

—

Not used

—

Male

15

69

—

—

User’s Guide

Extron Electronics, USA

1230 South Lewis Street
Anaheim, CA 92805
USA

714.491.1500
Fax [phone]

Extron Electronics, Europe

Beeldschermweg 6C
3821 AH Amersfoort
The Netherlands
+31.33.453.4040
Fax [phone]

Extron Electronics, Asia

135 Joo Seng Road, #04-01
PM Industrial Building
Singapore 368363
+65.6383.4400
Fax [phone]

Extron Electronics, Japan

Daisan DMJ Building 6F
3-9-1 Kudan Minami
Chiyoda-ku, Tokyo 102-0074 Japan
+81.3.3511.7655
Fax [phone]

www.extron.com

© 2002 Extron Electronics. All rights reserved.

Figure 3 — KP 6 application (with 5-pole captive
screw connector)

Operation

To select an input using the KP 6 Keypad Remote Control, press the
number key for the desired input.

Specifications

25 foot
cable

KP 6 Keypad

Remote Control

MSW 4V Switcher

MSW 4V SDI

POWER

1.2V
.5A MAX

INPUTS

OUTPUTS

1

2

3

4

CONTACT

1

2

3

4

A

B

Power ............................................. None required

Temperature/humidity .............. Storage -40° to +158° (-40° to +70°C)/ 10%

to 90%, non-condensing

Operating ...................................... +32° to +122° (0° to +50°C)/ 10% to 90%,

non-condensing

Enclosure type .............................. Plastic

Approvals ..................................... CE

MTBF ............................................. 30,000 hours

Warranty ....................................... 3 years parts and labor