Extron Electronics ISM HDSDI User Manual

Download

Extron

ISM HDSDI Output Board • Setup Guide

UNIVERSAL

SCALER

HDSDI

ISM HDSDI

output. The board mounts in one of the four vertical expansion slots (numbered 1 to 4) at the rear of the ISM 824. Refer to the ISM 824 User Guide, available at www.extron.com.

To install an ISM HDSDI output board in the ISM 824 base unit:

1. Turn off the ISM 824. Remove the power cord. Repeat for all connected devices.

2. Select an open slot at the rear, or take out a blank plate by removing the two

retaining screws (top and bottom), and lifting the plate away.

NOTE: Retain and reuse the screws to secure the new output board in place.

Retain the blank plates. If a board is already installed in the desired slot, remove the screws and carefully pull out the board.

The Extron® ISM HDSDI is a universal video and RGB scaler board with HDSDI output for the ISM 824. It has a single BNC connector and a local audio

3. Holding the new board by the frame,

align the front (non-connector end) of the board with the top and bottom plastic guides in the ISM 824. Slide the board in carefully, keeping within the guides. Push it into place ﬁrmly, and secure it with the retained screws.

4. If required, repeat steps 2 through 4

for any other output boards.

OUTPUT

R/ R-Y

OUTPUT

G/Y

R-Y

B/ B-Y

G/Y

OUTPUTS

1 2

R/R-Y

G/Y VID

B/C B-Y

H/HV

PASS THRU

B-Y

UNIV.

SCALER 70-544-01

VIDEO SCALER 70-545-01

ISM 824

Integration Scaling Matrix Switcher

OUTPUT

R/ R-Y

G/Y

B/ B-Y

H/ HV

PASS THRU

70-547-01

Align output board with top and bottom plastic guides.

OUTPUT

5. Power on the ISM 824. The new output

board(s) is autodetected, and takes approximately 30 seconds to initialize. The 16 character LCD display indicates the new board type, slot used, and counts down the initialization time. See inset for example display of a new ISM HDSDI board installed in slot #2, with 16 seconds left.

Example Output Board Installation

New U niv HDSDI Slot #2 16

70-546-01

6. Connect a suitable display device to the BNC connector. The output can be

conﬁgured via the front panel (see page 2) or by SIS™ commands (see page 3).

7. Insert a 5-pole captive screw connector into the local audio output connector

Ring

Tip

L R

Left

Right

Tip

NO GROUND HERE.

Sleeve(s)

Tip

NO GROUND HERE.

L R

Left

Right

Unbalanced Stereo Output

for balanced or unbalanced stereo output. Wire the connector as shown below.

Sleeve(s)

Balanced Stereo Output

R/ R-Y

G/Y

B/ B-Y

H/ HV

SCAN CONV.

CAUTION: For unbalanced audio, DO NOT connect the sleeves to the

negative contacts. Connect to center ground contact.

ISM HDSDI Output Board • Setup Guide, cont’d

ADJUST

ISM HDSDI Conﬁguration Menu

Using the front panel menu buttons (Menu and Next), the ISM HDSDI conﬁguration menu can be accessed. From the Output Conﬁguration screen, press Next until reaching the #x Univ HDSDI menu (see the image below). Press Menu and Next to navigate through the menus and use the front panel Adjust knobs ({ [), to change the settings as desired. Refer to the ISM 824 User Guide, online at www.extron.com for full details.

From the default cycle press Menu repeatedly to reach the Output Conﬁguration menu. Press Next (enters Select Output menu) and rotate either Adjust knob to select the Univ HDSDI menu. Follow the ﬁgure below to enter each menu and use the Adjust knobs to change the value.

Se lec t O utp ut

#8 U niv HD SDI

In put Se tup

As pec t R ati o

4: 3

Rotate either knob to select Aspect Ratio (4:3 or 16:9).

H St art V

12 8 1 28

Rotate knob to adjust H(orizontal) start. Rotate knob to adjust V(ertical) start.

Tot al Pix P has e

17 28 00

Rotate knob to adjust Total Pix value. Rotate knob to adjust Phase value. .

H Ac tiv e V

12 83 1 028

Rotate knob to adjust H active value. Rotate knob to adjust V active value.

#8 U niv HD SDI

Ou tpu t C onf ig

Re sol uti on

10 80i 60 Hz

Rotate knob to adjust resolution. Rotate knob to adjust refresh rate.

NOTE: Within any submenu, press the Menu button

to go directly to the top level (Output Card Configuration) menu. If, for 30 seconds, no button is pressed or Adjust knob is rotated, the menu times out and reverts to the default display cycle.

30 sec.

#8 U niv HD SDI

Us er Pre set s

Sa v e P re s et

<N A> 1 2 3

Rotate either knob to select a preset to save current settings.

Er ase Pr ese t

<N A> 1 2 3

Rotate either knob to select a preset to erase.

#8 U niv HD SDI

Ad va nce d C onf ig

Au to Im age

In put # 2 O ff

Te st Pa tt ern

<O ff> On

Au to Me mor y

Of f <O n>

Fu ll Scr een

In put #2 Of f

MENU NEXT

Rotate knob to select input. Rotate knob to turn On or Off.

No ne

Rotate either knob to select a test pattern.

Bl ue Mod e

Rotate either knob to turn blue mode On or Off.

Rotate either knob to turn auto memories On or Off.

Fi lm Mod e

Rotate either knob to turn film mode On or Off.

Rotate knob to select input. Rotate knob to turn On or Off.

Input Setup

The Input Setup submenu allows conﬁguration of aspect ratio, horizontal and vertical start points, total pixels and phase value, and active horizontal and vertical areas. Rotate the Adjust knobs as required to change values.

Output Conﬁg

The Output Conﬁg submenu displays and allows changes to be made to the resolution and refresh rate. Use the Adjust knobs to select a resolution and refresh rate.

Resolution 24 Hz 25 Hz 30 Hz 50 Hz 59.94 Hz 60 Hz

720p X X X X X X

1080i X X X

1080p X X X

User Presets

The User Presets submenu displays and allows the current settings to be saved as a preset, or to erase an existing saved preset. Use the Adjust knobs to select between the presets.

Advanced Conﬁg

Within this submenu the following settings can be adjusted: auto image (on or off), test pattern (selection), blue mode (on or off), auto memories (on or off), ﬁlm mode (on or off), and full screen (on or off).

Test Pattern

The test pattern submenu offers the following test patterns to choose from:

Color Bars

Crop

4:3/16:9

Crosshatch

1.33 Aspect

4x4 Crosshatch

1.78 Aspect

Split Grayscale

1.85 Aspect 2.35 Aspect

Ramp

Alternating

Pixels

Board-speciﬁc SIS Commands

The ISM HDSDI board can be conﬁgured with speciﬁc Simple Instruction Set™ (SIS) commands. The table below and on page 4 lists some of the ISM HDSDI board speciﬁc commands. Refer to the ISM 824 User Guide, at www.extron.com for a list.

Command ASCII

Command

(host to ISM)

Input selection

Video and audio X!*X@! Video X!*X@& Audio X!*X@$

NOTE: X! = input number, 0-8

= output number, 1-8

SIS commands and deﬁnitions continue on page 4.

Response

(ISM to host)

OutX@•InX!•All OutX@•InX!•RGB OutX@•InX!•Aud

Additional Description

]

Tie video/audio input X! to X@.

]

Select video input X! to X@.

]

Select audio input X! to X@.

ISM HDSDI Output Board • Setup Guide, cont’d

Command ASCII

Command

Response

(ISM to host)

(host to ISM)

Output scaler rate

Set output rate

View

X2!* X2@

= X2!*X2@

RteX@ *X2!*X2@

Start auto image

Start auto image 14*X@# ImgX@

Auto memory

On X@

Off

View setting

X@ X@

*1M

*0M

Aut1

Aut0

X1)]

Auto image

Enable

55*X@* X!*1#

X@ImgX!*1

Disable 55*X@* X!*0# X@ImgX!*0

View

55*X@* X!#

X1)

Input aspect ratio

16:9 9*X@*1# X@AspX!*1 4:3 9*X@*0# X@AspX!*0 View 9*X@#

X5%

Full screen

Enable 99*X@*X!*1# X@FulX!*1 Disable 99*X@*X!*0# X@FulX!*0 View 99*X@*X!#

X1)

Test pattern

On X@*X2) J X@TstX2) View X@ J

X2)

]

] ]

]

] ]

]

] ]

Additional Description

]

Set resolution/refresh rate.

View selected output rate.

Auto image input tied to X@.

Set auto memory to on.

Set auto memory to off.

View current auto memory.

Enables auto image for all inputs.

Disables auto image.

View auto image setting.

Set input aspect ratio to 16:9

Set input aspect ratio to 4:3

View current aspect ratio.

Enables full screen view.

Disables full screen view.

View the current on/off status.

Select test pattern.

View the test pattern selected.

NOTE: X! = Input number, 0-8

= Output number, 1-8

X1)

= Mode status, 1 = on, 0 = off

X2)

= Test pattern, 00 = off, 01 = color bars, 02 = 4:3/16:9 crosshatch, 03 = 4x4 crosshatch, 04 = split gray scale, 05 = ramp, 06 = alternating pixels, 07 = crop, 08 = 1.33 aspect, 09 = 1.78 aspect, 10 = 1.85 aspect, 11 = 2.35 aspect

X2!

= Output resolution, 17 = 720p, 18 = 1080i, 19 = 1080p

X2@

= Refresh rate, 1 = 50 Hz, 2 = 60 Hz, 7 = 24 Hz, 8 = 25 Hz, 9 = 30 Hz, 10 = 59.94 Hz

X5%

= Aspect ratio, 1 = 16:9, 0 = 4:3

Extron USA - West

Headqua rters

+800.6 33.9876

Inside USA / Canada Only

+1.714.491.1500 +1.714.491.1517 FAX

Extron USA - Eas t

+800.6 33.9876

Inside USA / Canada Only

+1.919.863.1794 +1.919.863.1797 FA X

Extron Euro pe

+800.3 987.6673

Inside Europe Only

+31.33.4 53.4040 +31.33.4 53.4050 F AX

Extron Asia

+800.7 339.8766

Inside Asia Only

+65.63 83.440 0 +65.63 83.466 4 FAX

Extron Japa n

+81.3.35 11.7655 +81.3.35 11.7656 FAX

Extron Chi na

+400. 883.1568

Inside China Only

+86.21. 3760.1568 +86.21. 3760.1566 FA X

Extron Mid dle East

+971.4.2 991800 +971.4.2 991880 FA X

68-1123-65

Rev A

08 10

Extron Electronics ISM HDSDI User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual