Extron Electronics IRCM-DV+ User Manual

IRCM-DV+ • Setup Guide

This guide provides instructions for an experienced installer to install and connect an Extron IRCM‑DV+. The IRCM‑DV+ is a hardwired remote control module for use with an Extron MediaLink® Controller (MLC) or System 5 IP Switcher. It replicates the front panel controls on both a VCR and a DVD player or a combination VCR/DVD player and uses commands stored in the MLC or sytem switcher to control those devices.

Up to two IRCM‑DV+ modules or one IRCM‑DV+ and up to two other control modules can be daisy chained together and connected to an MLC or System 5 IP switcher for basic A/V source and room control from several locations. One IR Emitter is included with each IRCM‑DV+. Additional IR Emitter and shield kits (part number 70‑285‑01) are available separately.

Installation

CAUTION: Installation and service must be performed by authorized personnel only. You must comply with the

following UL requirements:

1. This unit is not to be connected to a centralized DC power source or used beyond its rated voltage range.

2. The IRCM‑DV+ must be installed in a UL listed junction box.

3. The unit must be installed in accordance with the National Electrical Code and with local electrical and safety codes.

Step 1

Turn off all equipment and disconnect the equipment from the power source.

Step 2

Set the DIP switches on each control module as shown at right:

NOTES:

• Each IRCM‑DV+ is assigned two addresses

simultaneously: 0 and 1, or 2 and 3. The higher numbered address (1 or 3) address stores VCR commands, the other (0 or 2) stores DVD commands in the memory of the controller or system switcher. If an IRCM‑DV+ is assigned addresses 0 and 1, a different type of control module can be assigned to address 2 or 3.

• Each module must have a unique address. If other

modules have the same addresses as the IRCM‑DV+, then address conﬂicts may cause one or both modules to not be recognized by the controller or switcher.

Each controller or system switcher can support four control module addresses. Because each IRCM‑DV+ is assigned two addresses, you can connect only one other IRCM‑DV+ or up to two single‑address control modules to each controller or system switcher.

Step 3

Attach the IRCM‑DV+ control module(s) to the Extron faceplate(s) or Architectural Adapter Plate (AAP) wallplate(s). The IRCM‑DV+ ﬁts into a four space high opening.

Step 4

Connect the IRCM‑DV+ to the MLC or System 5 IP, and connect any other control modules to each other (if applicable) and to the IRCM‑DV+. See the diagram in ﬁgure 2 at right for details.

Both 5‑pole connectors are interchangeable. Wire both ends of the cable the same (pin A to pin A, for example). Do not connect more than one IR Link or two SCP control pads.

1 and 2 down (off) = address 0 and 1

1 up (on), 2 down (off) = address 1 and 0

Figure 1. Setting DIP Switches

Total max. distance to the farthest control module:

200' (61 m)

+12VDC

CM/IR/SCP

G+V

CM IR

+V OUT

GROUND

A B C D E

COMM LINK

GROUND

+12V OUT

CONT MOD

A B C D E

CM/ IR/SCP

Ground ( )

Control signal (IRCM)

ECBDA

System 5 IP

SCP

MLC 104 Plus Series

SCP

IR IN

MLC 226 IP Series

IR IN

SCP COM

A BB C

1 down (off), 2 up (on) = address 2 and 3

ADBC EADBC E

DIP Switches

1 up (on), 2 up (on) = address 3 and 2

A B C

Control

Module

NOTE: When running cables

long distances, you must use shielded cable and ground the drain wire.

To Another

Control Module

(1 more

IRCM-DV+

or up to 2 control modules

with single DIP switch addresses)

Figure 2. Connecting the IRCM‑DV+ to a System 5 IP or

an MLC and Another Control Module

IRCM-DV+ • Setup Guide (Continued)

100'

Step 5

Connect IR Emitters (one per each VCR, DVD player, or other device being controlled) to the MLC or System 5 IP, and afﬁx each emitter head near the IR receiver of the device (VCR, DVD player).

Step 6

IR Port on MLC or System 5 IP

IR Signal (+)

Figure 3. IR Emitter Wiring

(30.5 m)

Ground (−)

Restore power to the devices and set up the MLC or System 5 IP.

NOTES: • The conﬁguration should be created and uploaded to the MLC before the MLC is installed into the wall or

furniture.

• Conﬁguration and IR command learning require an RS‑232 or IP/LAN connection to the System 5 IP or the

MLC 104/226. See the user or setup guide for the MLC or switcher and the software help ﬁle for details on installing, operating, and setting up that device.

a. Associate the IRCM-DV+ with inputs on the MLC or System 5 IP. In Global Conﬁgurator, assign the DVD half of

the IRCM‑DV+ to an input button, then assign the VCR half to another input button. For detailed procedures, see the Global Conﬁgurator Help ﬁle.

b. For the System 5 IP or MLC 104 Plus or MLC 226 IP Series, if an Extron‑created driver is available for the VCR and the

DVD or the combination VCR‑DVD player, download the device driver(s) to the PC and load the commands to the Global Conﬁgurator project.

c. If needed, perform IR learning (the process by which the MLC or system switcher stores commands from an infrared

remote control) for each IRCM button for each device (VCR and DVD). See the the MLC or System 5 IP User Guide.

Step 7

Test the system.

• Verify that the DIP switches on the IRCM are set correctly.

• Verify that cables to and from the IRCM are wired the same at each end (pin A to pin A, pin B to pin B, and so forth).

• Verify LED function and check the responses of the VCR and DVD players.

NOTE: You must recycle power to an MLC in order for it to recognize an IRCM‑DV+ or any other control modules that

have been added after initial power‑on.

Step 8

Once conﬁguration and testing are complete, mount the MLC and the control module(s) into the wall/furniture.



Front Panel Features and Operation

DVD LED (amber) — Lights while the MLC or switcher input associated with

the DVD player is selected.

VCR LED (amber) — Lights while the input associated with the VCR is

selected.

NOTES:

• When an input that is not associated with that part of the

IRCM‑DV+ is selected, LEDs a and b turn off.

• The MLC or System 5 IP input must be selected (active) before

either part (DVD or VCR) of the IRCM‑DV+ can be activated and control the DVD or VCR.

Tx (transmit) LED — This LED lights whenever an IRCM‑DV+ button is

pressed.

Function buttons — These buttons replicate whichever VCR and DVD player

controls you assigned to them during conﬁguration.

1 2

DVD & VCR CONTROL

DVD VCR

TITLE MENU

TV/VCR

ENTER

PLAY NEXT/FWDPAUSE STOP

PREV/REW

Figure 4. Front Panel

TUNER

ExtronUSA ‑ West-

Headquarters

+800.633.9876 InsideUSA/CanadaOnly

+1.714.491.1500 +1.714.491.1517FAX

ExtronUSA ‑ East

+800.633.9876

InsideUSA/CanadaOnly

+1.919.863.1794 +1.919.863.1797FAX

ExtronEurope

+800.3987.6673

InsideEuropeOnly

+31.33.453.4040 +31.33.453.4050FAX

ExtronAsia

+800.7339.8766

InsideAsiaOnly

+65.6383.4400 +65.6383.4664FAX

ExtronJapan

+81.3.3511.7655 +81.3.3511.7656FAX

ExtronChina

+400.883.1568

InsideChinaOnly

+86.21.3760.1568 +86.21.3760.1566FAX

ExtronMiddle East

+971.4.2991800 +971.4.2991880FAX

68-689-50

Rev. A

0811