Extron Electronics IN3254 Setup Guide
Setup Guide — IN3254
RGsB,
This guide provides basic instructions for an
experienced installer to set up and operate the
Extron® IN3254 Distribution Amplifier (DA).
C
Installation and service must be performed
by authorized personnel only.
Step 1 — Turn off the DA and input/output devices
Turn the input and output devices off and unplug their power cords. Verify that the DA is
disconnected from the power source before proceeding.
Video outputs
4
1 2 3 4
LOW
IN3254
HI
VIDEO GA IN
SYNC LEV EL
X1.3
X1
Sync and gain
DIP switches
5
R
G
B
H
V
RGBHV
RGBS
Power
connector
1
Power LED
LISTED
1T23
C
U S
100-240V- 1.3A
50/60 Hz
Rear panel
2
3
Video input
R
I.T.E.
G
B
INP UT
H
V
R
G
B
OUT PU TS
H
V
Figure 1 – IN3254 connectors/controls and connection diagram
Step 2 — Attach input cables
Connect an RGBHV, RGBS, RGsB, RsGsBs, component video, S-video, or composite video
device to these BNC connectors (c). See figure 1 for information on how to cable the
BNC connectors.
Step 3 — Attach output cables
Connect up to four RGBHV, RGBS, RGsB, RsGsBs, component video, S-video, high
resolution monochrome video, or composite video output devices, such as projectors or
monitors, to these BNC connectors (d). See figure 1 for information on how to cable the
BNC connectors.
RsGsBs,
Component
S-video
Composite
video
Step 4 — Power on DA, input/output devices, and check for picture
Plug the external power supply cord into the power connector (a). When power is
applied to the unit, the front and rear panel LEDs (b) light.
Connect the power cords and turn on the input and output devices. The picture should
appear on the video displays.
N The output signal(s) must match the input signal. If the picture does not appear, check
that the BNCs for the output(s) and input are connected with an identical signal.
Step 5 — Adjust video gain and sync level
Use the sync and gain DIP switches (e) to select either high or low video gain and sync
level. Adjust video gain while viewing the displayed image to set the level that provides
the best picture quality.
Select 5 V peak-to-peak
sync output
Select 3 V peak-to-peak
sync output
HI
LOW
SYNC LEVEL
VIDEO GAIN
X1.3
X1
Apply gain for long cable runs, up to
200 feet (61 m) using Extron MHR cable
Do not add gain.
Setup Guide — IN3254 (cont’d)
ution
Step 6 — Mount the DA
If necessary, mount the line driver. Make any cabling
adjustments before mounting the line driver, as the
cables may be inaccessible afterwards.
The DA can be mounted using an optional Extron
2U universal rack shelf (part number 60-032-01) as
follows:
a. Remove the rubber feet if they were previously
installed on the bottom of the unit.
b. Place the DA on one side of the rack shelf. Align
the front of the DA with the front of the shelf and
align the threaded holes on the bottom of the DA
with the holes in the rack shelf.
Figure 2 – Rack shelf mount
c. Secure the DA to the rack shelf with the two provided 4-40 x 3/16 inch machine screws.
Insert the screws from the underside of the shelf and securely fasten them through
diagonally opposite corners.
d. Fasten the false front panel (provided with the rack shelf) to the unoccupied side of the
rack (as shown in figure 2), or install a second half-rack-width device on that side by
repeating steps a through c.
e. Secure the rack shelf to the rack using four 10-32 x 3/4 inch bolts. Insert the bolts through
#10 beveled washers, then through the holes in the mounting brackets.
Troubleshooting
If the image does not appear or is not displayed properly
• Make sure that all of the devices are powered on.
• Make sure that each device is receiving power. The front and rear panel LEDs on the DA
should be lit.
• Check the cabling and make adjustments as needed.
• Check the manuals of the input and output devices or contact Extron to determine if there
are special requirements to output video to the external video port.
If problems persist, contact the Extron S3 Sales and Technical Support Hotline.
Extron
IN3254
RGBHV
Distribution Amplifier
Front False
Faceplate
I
IN3204B
PL
M
A
N
IO
T
U
IB
R
T
IS
D
S
B
G
R
Extron
IN3254
RGBHV Distrib
Amplifier
R
IE
F
Extron USA - West
Headqua rters
+800.6 33.9876
Inside USA / Canada Only
+1.714.491.1500
+1.714.491.1517 FAX
INPUT
BUFFERED LOCAL
MONITOR OUTPUT
H. SHIFT
ID PIN 4
ID PIN 11
VGA INTERFACE W /ADSP
RGB 109 xi
Extron
RGB 109xi
VGA–UXGA
Interface
Projector
Monitor
PC
Figure 3 – Example of a typical IN3254 application
Extron USA - East
+800.6 33.9876
Inside USA / Canada Only
+1.919.863.1794
+1.919.863.1797 FA X
Extron Euro pe
+800.3 987.6673
Inside Europe Only
+31.33.4 53.4040
+31.33.4 53.4050 F AX
Extron Asia
+800.7 339.8766
Inside Asia Only
+65.63 83.440 0
+65.63 83.466 4 FAX
© 2010 Extron Electronics. All rights reserved.
Extron Japa n
+81.3.35 11.7655
+81.3.35 11.7656 FAX
Monitor
Projector
Extron Chi na
+400. 883.1568
Inside China Only
+86.21. 3760.1568
+86.21. 3760.1566 FA X
Extron Mid dle East
+971.4.2 991800
+971.4.2 991880 FA X
68-1015-50
Rev. B
03 10
Loading...