Extron Electronics IN2112R User Manual

HIGH RESOLUTION RACK MOUNTABLE INTERFACE
WITH 2 INPUTS AND STEREO AUDIO SWITCHING
IN2112R
IN2112R
OPER AT ION MANUAL
Installation and Safety Instructions
For Models without a Power Switch:
For all Models:
No serviceable parts inside the unit. Refer service to a qualified technician.
For Models with Internal or External Fuses:
For continued protection against fire hazard, replace only with same type and rating of fuse.
Instructions d’installation et de sécurité
Pour les modèles sans interrupteur de courant:
La prise de courant d’alimentation sera installé près de l’équipement et sera accessible.
Pour tout les modèles:
Pas de composants à entretenir à l’intérieur. Confiez toute réparation à un technicien qualifié.
Pour les modèles équipés de fusibles internes ou externes:
Afin d’éviter tout danger d’incendie, ne remplacer qu’avec le même type et la même valeur de fusible.
Installations- und Sicherheitshinweise
Für Geräte ohne Netzschalter:
Die Netzsteckdose soll in der Nähe des Gerätes installiert und frei zugänglich sein.
Für alle Geräte:
Keine Wartung innerhalb des Gerätes notwendig. Reparaturen nur durch einen Fachmann!
Für Geräte mit interner oder externer Sicherung:
Für dauernden Schutz gegen Feuergefahr darf die Sicherung nur gegen eine andere gleichen Typs und gleicher Nennleistung ausgewechselt werden.
Instalacion E Instrucciones de Seguridad
Modelos Sin Interruptor:
Para Todos Los Modelos:
Modelos con Fusibles Internos o Externos:
La conexión debe ser instalada cerca del equipo y debe ser accesible.
Dentro de la unidad , no hay partes para reparar. Llame un tecnico calificado.
Para prevenir un incendio, reemplace solo con el mismo tipo de fusible.
CE COMPLIANCE
All products exported to Europe by Inline, Inc. after January 1, 1997 have been tested and found to comply with EU Council Directive 89/336/EEC. These devices conform to the following standards: EN50081-1 (1991), EN55022 (1987) EN50082-1 (1992 and 1994), EN60950-92
Shielded interconnect cables must be employed with this equipment to ensure compliance with the pertinent Electromagnetic Interference (EMI) and Electromagnetic Compatibility (EMC) standards governing this device.
FCC COMPLIANCE
This device has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide against harmful interference when equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with th e instruction manual, may cause harmful interference to radio communications. Operation of equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at their own expense.
Table of Contents
Product Overview ................................................................................................2
Description........................................................................................................2
Product Features ...............................................................................................2
Compatibility........................................................................................................4
Input ..................................................................................................................4
Output................................................................................................................4
Adapter and Extension Cables for Input and Local Monitor Output................5
Installation............................................................................................................6
Application Diagram.........................................................................................7
Internal Control Connection..............................................................................8
Optimal Settings for LCD / DMD / ILA / D-ILA / Plasma Displays ...............8
Front Panel Connectors and Controllers...........................................................9
Horizontal Position Control..............................................................................9
Stereo Audio Switching..................................................................................10
Dipswitch Settings..........................................................................................11
Audio / Video / Phone / Data / Switch / Computer Connector Modules........12
Specifications......................................................................................................14
RGB Output Cables ........................................................................................15
Troubleshooting .................................................................................................16
Warranty.............................................................................................................17
2
Product Overview
DESCRIPTION
The IN2112R is a high-performance computer video interface for analog video signals including VGA, SVGA, XGA, MAC, Sun and other high-resolution workstations. The IN2112R combines high-resolution computer interfacing with two inputs, modular A/V connector plates and front panel A/C power outputs into a 2U rack mountable unit. This highly integrated approach gives audiovisual professionals the ability to quickly design and install functional, customized computer interfacing and A/V connectivity solutions for a broad spectrum of applications.
Like other INLINE interfaces, the IN2112R performs the following functions:
Signal Splitting - allows the simultaneous connection and viewing of both the computer’s local monitor
and a second output device such as an LCD data projector or a presentation monitor.
Physical Interfacing - Because computers employ many different types of video output connectors, it is
sometimes difficult to directly connect them to data projection devices. The IN2112R simplifies interfacing, routing and switching tasks by acting as a universal adapter. Through the use of removable input cables, the IN2112R can be attached to different computers and will provide a video output signal on five BNC connectors. The output signal may be set to RGBHV (default), RGBS or RGsB formats.
The IN2112R is not must be compatible with the horizontal scan rate output by the computer video card.
a scan converter. The data projector, monitor or other output device
PRODUCT FEATURES
Rack Mountable Unit - Featuring integral rack mounting ears, the IN2112R is specifically designed to
mount in a standard 19 equipment rack in a 2U space; no additional rack shelves or rack ears are required. The interface has a sleek black finish that blends well with other rack mounted equipment, complementing the decor of boardrooms, training facilities, control rooms and other high-tech / high profile installations featuring exposed equipment racks.
Two Input Switcher - Users may select Input 1 or Input 2 using a front panel switch. Front panel LEDs
illuminate to indicate the current input. In Autoswitch mode, the interface senses which input has an active signal and switches automatically. If both inputs are active, Input 2 has priority. Input 1 or 2 may be selected remotely via contact closure.
Modular Faceplate - Capable of holding up to eight A/V connector plates, the IN2112R can
accommodate the exact connectors required for each installation. Dozens of engraved connector plates are available for audio, video, computer, data and phone connections. INLINE can provide custom engraving services to label the connector plates as required for various applications (additional charge for custom engraving). Available A/V modules are listed on pages 12-13.
IN2112R OPERATION MANUAL - PRELIMINARY 8/23/99 ©1999 - INLINE, INC.
3
Front Panel A/C Power Outlets - The IN2112R has front panel power outlets (600 watts total) that
provide a convenient place to plug in a laptop computer, CD player or other portable A/V device that will be located in front of the equipment rack. Three models are available for each interface to support various A/C socket types worldwide:
IN2112R IN2112R - IEC IN2112R - EU
(2) Edison outlets (2) IEC female outlets (1) Schuko outlet
15-Pin HD VGA Standard Connectors - The IN2112R connects directly to VGA graphics cards and
VGA local monitors using high-resolution coaxial VGA extension cables such as the IN8000 series. Input / output adapter cable sets (see table on page 5) are also available in a variety of lengths for MAC (15-Pin D), SUN (13W3) and workstations (4 or 5 BNC).
Three Switching Modes - In Manual Mode, users select the desired input by pressing the front panel
input select button or remotely via serial or contact closure control. Remote Switching allows users to select inputs via any device that is capable of latching contact closure. With the Autoswitch Mode, the unit automatically selects the active input. If more than one input is active, input 2 has priority.
Wired Remote Control - The optional IN9465 Rocker Switch provides remote switching capability.
This switch duplicates the front panel input select button.
Ultra High-Resolution Amplification - The IN2112R provides superb performance and maximum
image clarity at any resolution. Several design elements combine to provide this level of performance: video bandwidth in excess of 400 MHz, buffered local monitor output, and input / local monitor output cables constructed of high-resolution coaxial materials.
Stereo Audio Switching - The IN2112R accepts unbalanced stereo audio from computer sound cards to
support multimedia applications. The stereo audio signal for each input is switched simultaneously with the video signal. The main audio output on the back of the interface (5-pin captive screw terminal) can be set to output an unbalanced or balanced audio signal. The two audio output connectors on the front panel provide a passive loop-through signal from each input and are ideal for local power speakers or a local recording device. These audio outputs are always live, even when the input is not currently selected.
CRT / LCD / DMD / ILA / HDLV / Plasma Friendly Output Signal - The output sync
characteristics can be set as needed to match the requirements of virtually any scan rate compatible data display. Internal dipswitches are provided for setting output sync format, sync polarity always negative / mirror input polarities, serration pulse enable / disable, and horizontal control enable / disable.
Selectable Output Sync Format - The unit can be set for RGBHV, RGBS or RGsB output sync as
required by the data display device and signal distribution system. The IN2112R does not strip sync off the green signal (i.e. RGsB input signals appear at the output as RGsB).
Convenient Controls and Features - A hand-adjustable horizontal position control on the IN2112R
faceplate allows for precise centering of the image within the data display area. The Auto Power feature automatically powers up the interface when an input cable is connected to the 15-pin HD input, and powers
©1999 - INLINE, INC. IN2112R OPERATION MANUAL - PRELIMINARY 08/31/00
4
down the unit when the input cable is removed. Auto monitor emulation emulates a VGA / MAC monitor when no local monitor is present.
In addition the IN2112R features:
Analog Interface - the unit will operate with Analog Video with TTL level sync signals. The signal
can be separate H & V or composite sync.
Sync Polarity Preservation Switch - enables the sync polarity to be preserved, or to be set for negative
polarity (for RGBHV signals in and out).
Serration Pulse Removal Switch - (for RGBS or RGsB output) enables the user to remove serration
pulses from the sync output.
Compatibility
INPUT
The IN2112R will accept high-resolution video signals from virtually any computer that outputs an analog video signal (VGA, SVGA, XGA, MAC, SUN, SGI and other high-resolution computers) at virtually any refresh rate. Input signal compatibility parameters are:
Video Signal: Analog RGB Video
Signal Format: RGBHV, RGBS, RGsB*
Horizontal Frequency Range: 30 KHz to 130 KHz
Vertical Refresh Rates: 30 Hz to 120 Hz
* The IN2112R will operate with RGsB input signals. However, the unit will not strip sync off of the green. RGsB input signals are always output as RGsB (they cannot be output as RGBS or RGBHV). Also, the horizontal position control will not operate when used with RGsB input signals.
OUTPUT
The output signal of the IN2112R is analog RGB video with TTL sync on 3, 4 or 5 female BNC connectors. The output format can be set to RGBHV, RGBS or RGsB using dipswitches. This output signal is compatible with high-resolution data grade monitors and data / graphics projectors.
IN2112R OPERATION MANUAL - PRELIMINARY 8/23/99 ©1999 - INLINE, INC.
5
VGA, MAC, SUN, SGI and other high-resolution workstations operate in several video modes encompassing a wide range of resolutions and scan rates. Many of the video signals from the newest models can run as high as 70 KHz or more, with the newest VGA cards offering an output resolution of 1600 x 1200 (some can even go as high as 1920 x 1080). The data projector or monitor connected to the interface output must be compatible with the horizontal scan rate and vertical refresh rate of the computer’s video signal. Please check the documentation for both the computer graphics card and the data display device to ensure compatibility.
ADAPTER / EXTENSION CABLES FOR INPUT AND LOCAL MONITOR OUTPUT
The IN2112R has 15-pin HD VGA-type connectors for input and local monitor output. The following input and local monitor output cables are available:
Computer 3’ 6’ 12’ 25’
VGA: 15-Pin HD
Input Cable Output Cable (Optional)
IN8006 IN8012 IN8025 IN8006 IN8012 IN8025
MAC with 15-Pin D:
Input Cable Output Cable
IN9140 IN9144
IN9141 IN9145
MAC G3, G4 and PowerBook with 15-Pin HD*:
Input Cable Output Cable
IN8006 IN8012 IN8025 IN8006 IN8012 IN8025
SUN: 13W3 (may also be used with SGI with RGsB output)
Input Cable Output Cable
IN9142 IN9146
IN9143 IN9147
Workstation: 5 BNC
Input Cable Output Cable
IN9048 IN9046 IN9046-L25 IN9047 IN9045 IN9046-L25
Workstation: 4 BNC
Input Cable
*Newer Mac G3 models (with translucent cases) have 15-Pin HD connectors (pins arranged in 3 rows). Older G3 models (with solid white enclosures) incorporate 15-Pin D connectors (pins arranged in 2 rows).
Note: The input / output cables listed above can be used with any
of the following interfaces, distribution amplifiers and switchers:
IN2100 IN2200
IN2110 IN3260
IN2111 Series IN3262 Series
IN2112 Series IN3264
IN2114 Series IN3268
IN9100
IN2116 IN3600 Series
©1999 - INLINE, INC. IN2112R OPERATION MANUAL - PRELIMINARY 08/31/00
6
Installation
This section offers instructions for installing the IN2112R interface (see Application Diagram on page 7).
1. Utilizing the integral rack mounting ears, mount the unit in a standard 19 equipment rack (or larger) in a 2U space. Run the necessary video coax cable, power cabled any other audio, video, phone, data or control / accessory cables (if used) to the unit.
2. Set the dipswitches for the requirements of your installation (see Dipswitch Settings on page 9). The IN2112R factory default output format is RGBHV. If your display device, routing system or cabling requires a different format, use the dipswitches to change the output signal to RGBS or RGsB as desired. For best results with LCD / DMD / ILA / D-ILA / Plasma Display devices, please refer to Page 8.
3. Connect the IN2112R output (5 BNC connectors) to the data display device's RGB input, using three, four or five high-resolution BNC cables or a multi-conductor RGBHV, RGBS or RGB "snake". The IN7000 / IN7100 / IN7200 / IN7300 Series high-resolution cables and the IN8800 Series installation cables are well suited for this purpose. While making connections, take care to insure that the red output is connected to the red input, green output to the green input, etc.
4. Connect the audio cable to the appropriate pins on the IN2112R 5-pin Phoenix connector (see diagram on page 10). Make sure that the four jumpers located near the audio output connector are set for the appropriate position for unbalanced or balanced stereo audio output as required by the installation. The factory default setting is unbalanced audio output. Connect the audio output wires to the appropriate connectors: Unbalanced Output - connect to the Left, Right and Ground connectors. Balanced Output - connect to Left +, Left-, Right+, Right- and Ground c onnectors.
5. Connect cables (if applicable) as required to the backside of the IN93XX A/V connector modules, and secure the modules to the IN2112R faceplate.
6. For applications incorporating remote switching, remove the cover (top and side screws) and refer to the Internal Connector Control Diagram on page 8. Installers can utilize an optional IN9465 Rocker Switch Module, which duplicates the front panel input select button. Remote switching allows users to select inputs via any device that is capable of latching closure.
7. Connect the power. The power connector has a sticker showing the correct polarity. Be extra careful to connect
the positive to the (+) connector and the negative to the (-) connector. Connecting the power with the reverse polarity may permanently damage the unit! If in doubt, measure the power cable with a voltmeter to verify the positive and negative terminals. You may also use the optional IN9210 rack mounted power supply
which will power up to 10 interfaces. The cable used to connect the power supply to the interface should be 18 gauge to 22 gauge, depending on its length. The INLINE IN8500P-2 power cable is well suited for this application.
8. If the IN2112R will use a remote input selection, connect the remote control cables to the approp riate connectors (see diagram on page 8). The remote connector requires a latching connection and works in conjunction with the front panel selector switch. Each time the remote connector circuit is opened or closed the IN2112R will select the opposite input. This could be either input 1 or input 2 depending on the position of the Input Select Switch (located on the front panel). The IN2112R remote connector has a STATUS pin that can provide feedback to a control system or remote button to indicate which input is currently selected. When the STATUS pin is low, this indicates that Input 1 is currently selected. If the STATUS pin is high, Input 2 is selected. Installers can incorporate an optional IN9465 Rocker Switch Module for remote switching.
9. Turn the computer and computer monitor off. Disconnect the computer monitor (if present) from the video output port on the computer.
IN2112R OPERATION MANUAL - PRELIMINARY 8/23/99 ©1999 - INLINE, INC.
7
10. Connect the local computer monitor (if present) to the local monitor output of the IN2112R. VGA monitors will attach directly to the local monitor output. For other types of monitors, use the appropriate local monitor output adapter cable (see list on page 5). If no local monitor is used, set the monitor emulation dipswitch to emulate a color VGA monitor or a 13/14 MAC RGB monitor.
11. Connect the output of the computer to the input of the IN2112R with the appropriate input cable.
12. Connect the computer sound card output (if present) to the audio input connector using an IN9106 audio patch cable. For computers with RCA connectors, use the IN9107 audio adapter cable. Connect powered local speakers (if present) to the local audio outputs.
13. Complete the installation by turning the computer and computer monitor on. If required, adjust the horizontal
position control to center the image on the date display device (see page 9). The user will override the input select button by applying the optional IN9465 Rocker Switch.
IN2112R APPLICATION DIAGRAM
©1999 - INLINE, INC. IN2112R OPERATION MANUAL - PRELIMINARY 08/31/00
8
IN2112R INTERNAL CONTROL CONNECTION WITH OPTIONAL IN9465 ROCKER SWITCH*
9GF/(' 2KP:
15RFNHU
, 6ZLWFK0RGXO
DWW5HVLVWRU
H
6 Z
L
W
6
F
Z
K
L
W
6
F
6
W
Z
K
D
L
W
W
7
X
F
R
V
K
,
Q
*
S
U
X
R
Y
W
X
G
Q
F
G
*Cover must be removed to connect remote
OPTIMAL SETTINGS FOR LCD / DMD / ILA / D-ILA / PLASMA DISPLAYS
The following output sync settings provide maximum sync signal preservation and are recommended for best image quality with LCD / DMD / ILA / D-ILA / Plasma Display devices. Depending on the design of the display device’s sync processing circuitry, you may be able to set the horizontal position control to the enabled position, however, experimentation with your display device is the best way to determine whether you can achieve a stable image with the horizontal position enabled. Most LCD displays include a fine phase control, which can be adjusted to optimize picture quality.
Dipswitch Setting: #2 Set to ON / All other dipswitches set to OFF Signal Format: Red / Green / Blue / Horizontal and Vertical Sync Horizontal Position Control: Disabled H & V Sync Polarity: Mirror Input Polarities
IN2112R OPERATION MANUAL - PRELIMINARY 8/23/99 ©1999 - INLINE, INC.
9
IN2112R FRONT PANEL CONNECTORS AND CONTROLS
HORIZONTAL POSITION CONTROL
The location of the horizontal position control is shown above. The horizontal position control adjusts the position of the image on the data display device from left to right (it has no effect on the local computer monitor).
Many data projectors and monitors have their own horizontal position control, and the interaction of the display devices and the interface’s horizontal controls may result in a dark image on the data display. The following procedure is suggested to ensure best results:
1. Adjust the IN2112R horizontal position control so a good quality image is displayed. This control should not be set to an extreme position.
2. Adjust the display devices horizontal position control until the image is centered as desired.
3. If the image appears dark or the colors are not properly displayed, fine tune the controls on both the display device and
the interface until the picture is centered and a good quality image is attained.
©1999 - INLINE, INC. IN2112R OPERATION MANUAL - PRELIMINARY 08/31/00
10
3RZHU*URXQGEOXH
%DODQFHG2XWSXW6LJQDO
6HW----WR&RQQHFW%RWWRP3LQV
STEREO AUDIO SWITCHING
The IN2112R provides stereo audio-follow-video switching to accommodate stereo audio signals from a computer audio card or other stereo audio sources. Whenever Input 1 or Input 2 is selected, the corresponding stereo audio signal is routed to the audio output connector on the back of the interface, which is normally connected to a house sound system.
AUDIO INPUTS
One 3.5mm female stereo mini jack is provided for each input. The input signal can be mono or stereo unbalanced audio (line level or 8 ohm).
AUDIO OUTPUTS
One 3.5mm female stereo mini jack is provided for each local output. The audio output connectors on the front of the interface provide a passive loop-out signal from the AUDIO INPUT connector. The audio output connectors can drive local powered speakers. If the input signal is line level, the local audio outputs can also be connected to a local recording device. The signal is always passed from the input to the local audio output whether that input is currently selected or not.
MAIN STEREO AUDIO OUTPUT
One 5-pin captive screw terminal is provided on the backside of the interface for stereo audio output (see Application Diagram on page 7). This connector outputs an audio signal from either Input 1 or Input 2 depending on which input is currently selected. The main audio output is set at the factory for unbalanced audio signal. The output can be set for either unbalanced audio or balanced audio by setting four internal jumpers located immediately adjacent to the 5-pin stereo audio connector as indicated below. When the unit converts an unbalanced input signal to balanced output, the gain remains constant.
PP0LQL6WHUHRFRQQHFWLRQ
IN2112R OPERATION MANUAL - PRELIMINARY 8/23/99 ©1999 - INLINE, INC.
5LJKW*URXQG
/HIW*URXQG
5LJKW*URXQG
/HIW*URXQG
5LJKW
/HIW
5LJKW 5LJKW
/HIW /HIW
9GFUHG
9GFEODFN
-
-
% D O
8QEDODQFHG2XWSXW6LJQDO
8 Q E
6HW----WR&RQQHFW8SSHU3LQV
D O
% D O
8
G
Q E
H
D O
F Q
-
D
O D E Q 8
% D O
G H F Q D
O D %
8 Q E D O
-
)DFWRU\'HIDXOWLV%DODQFHG2XWSXW
% D O
8 Q
-
E D O
11
DIPSWITCH SETTINGS
Most installations will not require any changes to the dipswitch settings, and the IN2112R will generally be operated with the factory default settings. The Factory Default settings and specialized dipswitch settings are indicated below. Please note that when the interface is held upright, the dipswitches are numbered from 10 to 1 as shown below.
OFF
ON
Factory Default Settings: Dipswitches ON:
Signal Format: Horizontal Position Control: H & V Sync Polarity: Serration Pulse Generator: Monitor Emulation Input 1: Monitor Emulation Input 2: Autoswitching:
1, 2, & 4 Red / Green / Blue / Horizontal and Vertical Sync Enabled Negative, Negative Serration Pulses Enabled Auto Termination Enabled Auto Termination Enabled Disabled
The table below lists the functions of the 10 dipswitches:
Switch Function Setting
1
2
3
4
5
6
7
8
9
10
Horizontal Position Control Output Sync Format Selection:
Select Sync on Green or Separate Sync
Output Sync Format Selection: Select RGBS or RGBHV
RGBHV Output Polarity
Serration Pulse Generator
Input A Monitor Emulation - Pin 11
Input A Monitor Emulation - Pin 10
Input B Monitor Emulation - Pin 11
Input B Monitor Emulation - Pin 10
Input A/B Auto-Switch
*Factory Default Settings
110
On Horizontal Position Enabled* Off Horizontal Position Disabled On RGBS / RGBHV* Off Sync on Green On RGBS Off RGBHV* (Switch 2 must be On in order to get RGBS or RGBHV Output Format) On Negative Sync Polarities* Off Mirror Input Polarities On Serration Pulses Disabled Off Serration Pulses Enabled* On Pin 11 Always Grounded Off Pin 11 State Set by Auto Termination* On Pin 10 Always Grounded Off Pin 10 State Set by Auto Termination* On Pin 11 Always Grounded Off Pin 11 State Set by Auto Termination* On Pin 10 Always Grounded Off Pin 10 State Set by Auto Termination* On Auto-Switch Enabled Off Auto-Switch Disabled*
©1999 - INLINE, INC. IN2112R OPERATION MANUAL - PRELIMINARY 08/31/00
12
AUDIO / VIDEO / PHONE / DATA / SWITCH / COMPUTER CONNECTOR MODULES
Modular A/V Connector Plates & Accessories for:
IN2111 Series / IN2112 Series / IN2114 Series / IN2116 / IN3260 / IN9166 / IN9167 / IN9168
Connector Module
Black/White
IN9350B / IN9350W Blank Plate - Single Size None None Single IN9351B / IN9351W (2) BNC Barrel (2) BNC Female (2) BNC Female Single IN9352B / IN9352W (1) S-Video 4-pin Mini DIN Female 4 Bare Wires Single
IN9353B / IN9353W (2) RCA IN9354B / IN9354W (2) ¼” Stereo Phono (2) ¼” Stereo Phono Female (3) Solder Lug Terminals Single
IN9355B / IN9355W (2) 3.5mm Mini Stereo (2) 3.5mm Mini Stereo Female (3) Solder Lug Terminals Single IN9356B / IN9356W
(1) 5-PIN Captive Screw
Terminal IN9357B / IN9357W (2) F-Connector Barrel (2) F-Connector Female (2) F-Connector Female Single IN9358B / IN9358W (1) RJ11 RJ11 Female - Leviton Brand 6-pin Punch Block Single
IN9359B / IN9395W (1) RJ45
IN9360B / IN9360W
(1) Contact Closure
Switch With LED &
(1) 3.5mm Mini Stereo IN9361B / IN9361W (1) 15-pin HD 15-pin HD Female 15-pin HD Female Single IN9362B / IN9362W (1) 15-pin HD 15-pin HD Male 15-pin HD Male Single
IN9363B / IN9363W IN9364DB /
IN9364DW IN9365DB / IN9365DW IN9366DB / IN9366DW IN9367DB / IN9367DW IN9368TB / IN9368TW IN9369QB / IN9369QW
IN9372DB / IN9372DW
(1) S-Video Barrel &
(1) BNC Barrel
(1) 4-pin XLR
(1) 3-pin XLR
(1) 6-pin XLR
Blank Plate - Double
Blank Plate - Triple
Blank Plate - Quad
A/V Super Module:
(2) RCA - Audio &
(1) RCA - Video &
(1) S-Video IN9373B / IN9373W (2) RCA Barrel (2) RCA Female (2) RCA Female Single
IN9374B / IN9374W
(1) 9-Pin D Gender
Changer – Female
Description
Front Connector /
Termination
(1) RCA Female - Red (1) RCA Female - Black
Phoenix Brand 5-pin Captive Screw Terminal
RJ45 Female - Leviton Brand Square White Single Pole
Switch with Integrated LED
Back Connector /
Termination
(2) Solder Lug Terminal (2) Solder Lug Terminals
(5) Solder Lug Terminals Single
8-pin Punch B l ock for Cat 5 Cable
(4) Solder Lug Terminals
3.5mm Mini Stereo Female (3) Solder Lug Terminals
4-pin Mini DIN Female 4-pin Mini DIN Female BNC Female BNC Female Neutrik Brand 4-pin XLR Female Neutrik Brand 3-pin XLR Female Neutrik Brand 6-pin XLR Female
None
None
None
(4) Solder Cups
(3) Solder Cups
(6) Solder Cups
None
None
None
RCA Female - Red (2) Solder Lug Terminals RCA Female - Black (2) Solder Lug Terminals RCA Female - Yellow (2) Solder Lug Terminals 4-pin Mini DIN Female 4 Bare Wires
(1) 9-pin D Female
(1) 9-pin D Female
Module
Size
Single
Single
Single
Single
Double
Double
Double
Double
Triple
Quad
Double
Single
IN2112R OPERATION MANUAL - PRELIMINARY 8/23/99 ©1999 - INLINE, INC.
13
Connector Module
Black/White
IN9375B / IN9375W
IN9376B / IN9376W
IN9377DB / IN9377DW
IN9378B / IN9378W IN9381B / IN9381W (1) BNC Barrel (1) BNC Female (1) BNC Female Single
IN9382B / IN9382W (1) F-Connector Barrel (1) F-Connector Female (1) F-Connector Female Single IN9383B / IN9383W (1) RCA Barrel (1) RCA Female (1) RCA Female Single IN9384B / IN9384W (1) ¼” Stereo Phono (1) ¼” Stereo Phono Female (3) Solder Lug Terminals Single IN9385B / IN9385W (1) 3.5mm Mini Stereo (1) 3.5mm Mini Stereo Female (3) Solder Lug Terminals Single
IN9386B / IN9386W
IN9387B / IN9387W
IN9388B / IN9388W
IN9389B / IN9389W
IN9394DB / IN9394DW IN9395DB / IN9395DW IN9396DB / IN9396DW
(2) Keyboard / Mouse Connectors A/V Super Module with Barrel Connectors: (2) RCA - Audio & (1) RCA - Video & (1) S-Video
(2) RCA - Audio & (1) RCA - Video
(1) 9-pin D Gender Changer - Male
(1) BNC Barrel & (1) 3.5mm Mini Stereo
(1) S-Video & (1) 3.5mm Mini Stereo
(1) RCA for Video & (1) 3.5mm Mini Stereo (1) 6-PIN Mini DIN Barrel (PS/2 Keyboard / Mouse)
(1) 4-pin XLR
(1) 3-pin XLR
(1) 6-pin XLR
Description
Front Connector /
Terminal
(2) 6-pin Mini DIN Female
Back Connector /
Terminal
(2) 6-pin Mini DIN
Female RCA Female - Red RCA Female RCA Female - Black RCA Female RCA Female - Yellow RCA Female
4-pin Mini DIN Female
4-pin Mini DIN Female RCA Female - Red (2) Solder Lug Terminals
RCA Female - Black (2) Solder Lug Terminals RCA Female - Yellow (2) Solder Lug Terminals
(1) 9-pin D Male
(1) 9-pin D Male
BNC Female BNC Female
3.5mm Mini Stereo (3) Solder Lug Terminals 4-pin Mini DIN Female 4 Bare Wires
3.5mm Mini Stereo (3) Solder Lug Terminals Yellow RCA Female
(1) 6-pin Mini DIN Female
(2) Solder Lug Terminals
(1) 6-pin Mini DIN
Female
Switchcraft 4-pin XLR Female (4) Solder Cups
Switchcraft 3-pin XLR Female (3) Solder Cups
Switchcraft 6-pin XLR Female (6) Solder Cups
Module
Size
Single
Double
Double
Single
Single
Single
Single
Single
Double
Double
Double
Note: When ordering the IN2112R, please specify the necessary A/V connector modules.
©1999 - INLINE, INC. IN2112R OPERATION MANUAL - PRELIMINARY 08/31/00
14
Specifications
Input
Connector Type (2) 15-pin HD male - standard VGA pin-outs RGB Video Signals Analog, 1.5 Vp-p max. Input Impedance 75 ohm Sync Signals TTL compatible Horizontal Scan Rate 30 KHz - 130 KHz Vertical Sync Range 30 Hz - 120 Hz Stereo Audio Connector (2) 3.5mm stereo mini female - Impedance: 10 Kohm
Output
Local Monitor (Buffered) (2) 15-pin HD female - standard VGA pin-outs Main Output (5) female BNC connectors
Output Signal Formats RGB Signals Analog Video, 75 ohm impedance
Bandwidth 400 MHz @ -3 dB with .7 volt input signal Rise and Fall Times 0.875 nano seconds
Gain 1.0 +/- 5% (unity)
Sync Signal
H, V and S: 4V Unterminated; 2V when 75 ohm terminated
Horizontal Pulse Width
Vertical Pulse Width Approximately the same as the input signal Local Audio Outputs (2) 3.5mm stereo mini female for Unbalanced Audio
Stereo Audio Output (Passive)
Controls
External
Internal
Dimensions
Size (including faceplate) 3.5 H x 19 W x 5.5 D / 8.9cm x 48.3cm x 14.0cm Shipping Weight 6 lbs. / 3 kg.
Power
Power Supply Internal Universal: 90 - 240VAC; 47 - 63Hz
Front Panel A/C Outlets
Regulatory Compliance
Safety UL 1950, CAN/CSA-22.2 No. 950 3rd Ed. EMI
RGBHV - Negative sync polarities (default)
RGBHV - Mirror input sync polarities, RGBS or RGsB
Gs: 0.3V when 75 ohm terminated Horizontal Position Enabled: Approximately 1.5 usec Horizontal Position Deleted: Approximately the same
as the input signal
5-pin mini Phoenix captive screw terminal
for balanced or unbalanced audio; Impedance: 50 ohm
Horizontal Position Control
Input Selector
10 Dip Switches
Audio Output Unbalanced / Balanced (4 jumpers)
600 Watts Total
IN2112R: (2) Edison female IN2112R-IEC: (2) IEC female IN2112R-EU: (2) Euro female
FCC class A; CE: EN50022 (1987), EN50081-1 (1991),
EN50082-1 (1992 & 1994), EN60950-92
IN2112R OPERATION MANUAL - PRELIMINARY 8/23/99 ©1999 - INLINE, INC.
15
Parts Included (1) IN2112R Rack Mountable Interface
(1) IN9334 3/32 Allen Wrench for IN2112R Connector Module Set Screws (1) IEC Power Cable (1) Operation Manuel
Required Accessories (Ordered Separately) Input and Local Monitor Adapter and Extension Cables:
VGA: IN8000 Series 15-pin HD male to 15-pin HD female, various lengths from 3 to 100 For Other Computers: See list on page 4
Optional Accessories Power Equipment:
IN9210: Rack mountable power supply, powers up to 10 units Remote Equipment:
IN9465: Rocker Switch Module Audio Input Cables:
IN9106: 3.5mm stereo mini male to 3.5mm stereo mini male, 6 long IN9107: (1) 3.5mm stereo mini male to (2) RCA male, 6 long
Installation Cables: IN7000P-5 Series RGBHV Cable: IN7000P-5K Series RGBHV Cable: Standard Resolution, Plenum Cable available in 1000 bulk length IN8800:
(5) 26 Gauge Twisted Pairs, (1) Gauge Pair
18 Conductor Super High-Resolution Cable: (3) Super High-Res. Coax., (3) Mini Coa x.,
Connectors and Tools: IN9301 BNC Connectors
IN9320 Crimp Tool Frame IN9321 Die (IN9320 and IN9321 are used to terminate bulk cables)
Standard Resolution, Plenum Cable available in bulk lengths
RGB OUTPUT CABLES
Cables 3-Conductor 4-Conductor 5-Conductor 6-Conductor
Standard Resolution IN7000-4 IN7000-5
Standard Resolution, Plenum IN7000FP-4 IN7000FP-5 Ultra High Resolution IN7200-3 IN7200-4 IN7200-5 IN7200-6 Super High Resolution IN7300-5 IN7300-6
Super High Resolution, Plenum IN7300P-5
All cable grades are available in lengths from 3 to 250 pre-terminated with high quality BNC connectors or as bulk cable.
©1999 - INLINE, INC. IN2112R OPERATION MANUAL - PRELIMINARY 08/31/00
16
Troubleshooting
The display device connected to the IN2112R output has a bad / scrambled image. Solution 1: Verify that the correct input cable is being used (see list on page 5).
Solution 2: The display device connected to the output of the interface may not be compatible with the
computer output. Standard 640 x 480 VGA runs at 31.5 KHz, and SVGA can be as high as 48
- 58 KHz, depending on the vertical refresh rate. PC, MAC, SUN and other high-resolution workstations have new and ultra high-resolution modes such as 1600 x 1200 and 1800 x 1440, and can output a video signal with a horizontal scan rate of over 100 KHz! Many data monitors and data projectors are not compatible with these resolutions and frequencies.
Solution 3: Check the dipswitch settings to make sure the unit is putting out a sync format that the display
device can use. For most applications, the default dipswitch settings (see page 11) will work best. For LCD / DMD / ILA / D-ILA / Plasma Display devices, you may have to disable the horizontal position control.
Solution 4: The RGBS or RGBHV cable may have a bad sync line. Try running the sync through another
cable.
Solution 5: The IN2112R output sync range may not be compatible with the display device. Check the
resolution and refresh rate for both the computer graphics card and the data display device to ensure compatibility.
The output image is very dark. Solution: The horizontal position control may be set off to an extreme setting or may be interacting
poorly with the horizontal position control on the display device. Follow the horizontal position adjustment procedure on page 9.
The local monitor looks fine but the image on the LCD projector is wavy or has vertical bars in the picture.
Solution 1: LCD / DMD / ILA / D-ILA / Plasma Display devices work best when the sync signal has
minimum sync processing. Set the interface dipswitches as indicated in the section OPTIMAL SETTINGS FOR LCD / DMD / ILA / D-ILA / PLASMA DISPLAY DEVICES on page 8.
Setting the interface to RGBHV output and disabling the horizontal position control may alleviate this problem.
Solution 2: LCD / DMD displays often have an adjustment called Phase Adjust or Fine Phase Control.
This control should be adjusted to provide the best image.
The output image is missing a color. Solution: Possibly the RGBS or RGBHV cable is bad. Try switching connections on the output to verify
that the bad colors cable is OK (Example: If there is no red, try running the green output through the red cable and see if the green is displayed or not).
The output image is too green. Solution: The dipswitch settings may be set for sync on green output and the display device doesnt like
that format. Try changing the dipswitches to output an RGBS or RGBHV signal (see
Dipswitch Settings on page 11).
The horizontal position control is not working. Solution 1: Check the dipswitch settings to see if the horizontal position control has been disabled.
Solution 2: The input setting may be RGsB (sync on green). The horizontal position control does not work
with RGsB input signals.
IN2112R OPERATION MANUAL - PRELIMINARY 8/23/99 ©1999 - INLINE, INC.
17
The output image is doubled, with two images displayed side-by-side. Solution: The display device may not be compatible with the horizontal scan rate of the computer. This
problem often occurs when a 31.5 KHz VGA signal is sent into an RGB monitor that is only compatible with signals at 15.75 KHz.
If problems persist, call INLINE Technical Services at (800) 882-7117 for further assistance.
Warranty
INLINE warrants the equipment it manufactures to be free from defects in materials and
workmanship.
If equipment fails because of such defects and INLINE is notified within two (2) years from the date
of shipment, INLINE will, at its option, repair or replace the equipment at its plant, provided that the equipment has not been subjected to mechanical, electrical or other abuse or modifications.
Equipment that fails under conditions other than those covered will be repaired at the current price of parts and labor in effect at the time of repair. Such repairs are warranted for ninety (90) days from the day of re-shipment to the Buyer.
This warranty is in lieu of all other warranties expressed or implied, including without
limitation, any implied warranty or merchantability or fitness for any particular purpose, all of which are expressly disclaimed.
The information in this manual has been carefully checked and is believed to be accurate. However, INLINE, Inc. assumes no responsibility for any inaccuracies that may be contained in this manual. In no event will INLINE, Inc. be liable for direct, indirect, special, incidental, or consequential damages resulting from any defect or omission in this manual, even if advised of the possibility of such damages. The technical information contained herein regarding IN2112R features and specifications is subject to change without notice.
IBM is a registered trademark of In ternation al Business Mach ines. Apple, M AC, Quadra and Cent ris are registered trademarks of Apple Computers, Inc. Iris Indigo is a registered trademark of Silicon Graphics. Sun Sparc Station is a registered trademark of Sun Micros ystems, Inc. All oth er trademarks and registered trademarks are the property of their respective companies.
All Rights Reserved © Copyright 1999
©
(800) 882-7117 ♦ (714) 450-1800 ♦ FAX (714) 450-1850 ♦ www.inlineinc.com
INLINE, INC. ♦ 810 West Taft ♦ Orange, CA 92865
©1999 - INLINE, INC. IN2112R OPERATION MANUAL - PRELIMINARY 08/31/00
Loading...