Extron electronics IN1608 xi Series Setup Manual

Download

Page 1

IMPORTANT:

installation instructions,

specifications bef

oduct to the po

IN1608 xi SA

Go to www.extron.com for the complete

IN1608 xi Series • Setup Guide

user guide,

The Extron IN1608 xi Scaling Presentation Switcher is an eight input, HDCP-compliant video scaler that accepts a wide variety of audio and video formats and provides HDMI and DTP/HDBaseT video outputs. This guide provides instructions for an experienced user to set up and congure IN1608 xi, IN1608 xi SA, IN1608 xi MA 70, IN1608 xi IPCP SA, and IN1608 xi IPCP MA 70 scalers. It covers how to perform basic operations using the front panel controls and selected Simple Instruction Set (SIS™) commands.

NOTES:

• For full installation, conguration, menus, connector wiring, and operation details, see the IN1608 xi Series User Guide

at www.extron.com. For installation, conguration, and operation details of the IPCP Pro dual-NIC embedded control processor, see the IPCP Pro Series User Guide.

• The IN1608 xi Series products can also be congured via the Extron Product Conguration Software (PCS), available at

www.extron.com. For information on using PCS, see the IN1608 xi Series Help le

Installation

IN1608 xi Series Rear Panel Connectors

and

ore connecting the

wer source.

AMPLIFIED OUTPUT

2x25W(8Ω)/2x50W(4Ω)

L3R

CLASS 2 WIRING

RESET

RS-232

Tx Rx

REMOTE

100-240V ~ 1.5 A MAX

50/60 Hz

CONFIGURABLE

IN1608 xi IPCP SA

HDMI

INPUTS

DIGITAL I/OCOM 3COM 2COM 1

Tx Rx

RTSCTSGTx Rx GTxRxG

IR/SERIAL eBUSRELAYS

RS-232 IR

Tx Rx Tx RxG

SIG LINK

HDMI

OVER DTP

RS-232 IR

DTP IN

Tx Rx Tx RxG

1122C34C

SSGG

SIG LINK

DTP IN

OVER TP

RS-232 IR

Tx Rx Tx RxG

1234G

-S G+S+V

PWR OUT = 6W

SIG LINK

OUT

OUTPUTS

AV LAN 3

AV LAN 2

AV LAN 1

LAN

HDBT

HDMI

DTP

LL1

AUDIO INPUTS

+48V

MIC/LINE

VARIABLE

OUTPUTS

Figure 1. Rear Panel Connectors, IN1608 xi IPCP SA

Power and Input Connections Output Connections Control Connections

AC power connector

Configurable analog 15-pin HD (VGA)

connectors (inputs 1 and 2)

HDMI inputs (inputs 3 through 6)

DTP inputs and corresponding RS-232/IR Over

DTP connectors (inputs 7 and 8)

Analog audio inputs (associated with inputs 1

through 6)

Mic/Line audio inputs and adjacent phantom

DTP/HDBaseT output connector and

corresponding RS-232/IR Over TP connector (output 1C)

DTP/HDBaseT mode selection switch

for twisted pair output

HDMI outputs (outputs 1A and 1B)

Analog audio outputs

Amplified audio output

(SA and MA models only)

Remote RS-232 port

IPCP Pro dual-NIC

embedded control processor (IPCP models only)

LAN connector

(non-IPCP models only, see the note and illustration below)

power LEDs

The IN1608 xi IPCP models feature a built-in Extron IPCP Pro dual-NIC control processor for controlling and monitoring a variety of external devices, such as projectors and lights (see the IPCP Pro Series Setup Guide for more details).

NOTE: The non-IPCP models have a LAN connector next to the Remote RS-232 connector (see

the illustration at right) instead of the IPCP Pro control processor.

OUTPUTS

VARIABLE

AMPLIFIED OUTPUT

2x25W(8Ω)/2x50W(4Ω)

CLASS 2 WIRING

RESET

LAN

REMOTE

RS-232

Tx Rx

Page 2

IN1608 xi • Setup Guide (Continued)

Furniture Mounting

Rack Mounting

Mounting and Cabling

Step 1 — Mount the device

a. Turn off or disconnect all equipment power.

b. Mount IN1608 xi scaler to a rack using the

pre-installed rack ears, or use an optional mounting kit for under-desk mounting (see the two images at right).

The IN1608 xi comes in a 1U, full rack width enclosure (shown in the examples at right). All other IN1608 xi models come in 2U, full rack width enclosures.

Step 2 — Connect inputs

a. Connect analog video sources to the VGA connectors (see gure 1, B, on the previous page).

b. Connect digital HDMI or DVI (with an appropriate adapter) sources to the HDMI connectors (C).

c. Connect a DTP transmitter to the DTP input connectors (D). For cable wiring and recommendations, see Twisted Pair

Recommendations for DTP and HDBaseT Communication on the next page.

Signal LED — Lights green when the unit is receiving an active video signal from a DTP transmitter.

Link LED — Lights amber when a valid link is established to a DTP transmitter.

d. To pass serial or infrared data, connect the control device to the RS-232 and IR Over DTP captive screw connectors

(see RS-232 and IR Over TP Wiring on the next page). Alternatively, insert RS-232 communication to a DTP/HDBaseT endpoint via Ethernet (see the IN1608 xi Series User Guide for more information).

e. Connect analog audio sources to the inputs via the 5-pole captive screw connectors (E). See Audio Wiring on the next

page for more information.)

f. Connect Mic/Line audio sources to the inputs via the 3-pole captive screw connectors (F).

Rack Ears

Mounting Screws (2) Places Each Side

#8 Screw (4) Places Each Side

MBU 149

Mounting Bracket

Step 3 — Connect outputs

a. Set the twisted pair switch (H) to one of the following positions:

• HDBT — Set the twisted pair switch to the Up position to set the twisted pair connector for HDBaseT

communication. The switch returns to the middle position after.

• DTP — Set the twisted pair switch to the Down position to set the twisted pair connector for DTP communication.

b. Connect an DTP/HDBaseT-compatible device to the HDBT output connector (G). For cable wiring and

recommendations, see Twisted Pair Recommendations for DTP and HDBaseT Communication.

Signal LED — Lights green when the scaler is outputting active video.

Link LED — Lights amber when a valid link is established between the scaler and the DTP/HDBaseT sink.

c. To pass serial or infrared data, connect a control device to the RS-232 and IR Over DTP captive screw connector (see

RS-232 and IR Over TP Wiring on the next page). Alternatively, insert RS-232 communication to a DTP/HDBaseT

endpoint via Ethernet (see the IN1608 xi Series User Guide for more information).

d. Connect suitable video displays to the HDMI connectors (I).

e. Connect analog audio devices to the outputs via the 3.5 mm, 5-pole captive screw connectors (J). See Audio Wiring

on the next page for more information.

f. For SA and MA models, connect speakers to the Amplied Output via the 5 mm 4-pole or 2-pole captive screw

connector (K).

Step 4 — Connect control devices

a. To control non-IPCP models through Ethernet, connect a LAN or WAN to the LAN connector (see N on page 1). For the

IPCP models, connect a LAN or WAN to any of the LAN connectors on the IPCP Pro control processor (M). The default IP address of the scaler is 192.168.254.254. The default subnet mask is 255.255.255.0.

b. For serial RS-232 control, connect a host device to the 3-pole captive screw connector (L). The default baud rate is

9600.

c. For control through USB, connect a host device to the front panel USB mini-B port (see gure 2, A on page 4).

Page 3

Step 5 — Set up the IPCP Pro 355 control processor (IPCP models only)

Slee

No Ground Here

Slee

Do not tin the wires!

12345678

RJ-45

Insert Twisted

Pair Wires

Pins:

Wire color

White-green

Green

White-orange

Blue

White-blue

Orange

White-brown

Brown

Wire color

T568A T568B

White-orange

Orange

White-green

Blue

White-blue

Green

White-brown

Brown

See the IPCP Pro Series Setup Guide, available at www.extron.com, for installation details.

Step 6 — Connect power

Connect a 100 to 240 VAC, 50-60 Hz power source to the AC power connector (see gure 1, A, on page 1).

TIA/EIA-T568B

Pin Wire Color

1 White-orange

2 Orange

Twisted Pair Recommendations for DTP and HDBaseT Communication

Extron recommends using the following practices to achieve full transmission distances and reduce transmission errors:

• Use Extron XTP DTP 24 SF/UTP cable for the best performance. At a minimum, Extron

recommends 24 AWG, solid conductor, STP cable with a minimum bandwidth of 400 MHz.

• Terminate cables with shielded connectors to the TIA/EIA-T568B standard (shown at

3 White-green

4 Blue

5 White-blue

6 Green

7 White-brown

8 Brown

right).

• Limit the use of more than two pass-through points, which may include patch points, punch down connectors, couplers, and

power injectors. If these pass-through points are required, use shielded couplers and punch down connectors.

ATTENTION:

• Do not connect these connectors to a computer or telecommunications network.

• Ne connectez pas ces ports à des données informatiques ou à un réseau de télécommunications.

• DTP remote power is intended for indoor use only. No part of the network that uses DTP remote power should be routed

outdoors.

• L’alimentation DTP à distance est destiné à une utilisation en intérieur seulement. Aucune partie du réseau qui utilise

l’alimentation DTP à distance ne peut être routée en extérieur.

NOTE: When using shielded twisted pair cable in bundles or conduits, consider the following:

• Do not exceed 40% ll capacity in conduits.

• Do not comb the cable for the rst 20 meters, where cables are straightened, aligned, and secured in tight bundles.

• Loosely place cables and limit the use of tie wraps or hook-and-loop fasteners.

• Separate twisted pair cables from AC power cables.

RS-232 and IR Over TP Wiring

To pass bidirectional serial command signals between DTP or HDBaseT-compatible devices, connect a control device to the three leftmost poles (Tx, Rx, and G) of the 5-pole captive screw connector. To transmit and receive IR signals, connect a control device to the three rightmost poles (G, Tx, and Rx).

NOTE: Alternatively, RS-232 data can be inserted via Ethernet (see the IN1608 xi Series User Guide for details).

Audio Wiring

Wire the audio input and output connectors as shown at right. Use the supplied tie wrap to strap the audio cable to the extended tail of the connector. This does not

apply to the amplied audio output connector on the SA and MA models.

ATTENTION: For unbalanced outputs, do not

connect wires to the “-” poles (see the Extron Audio Wiring Card).

ATTENTION : Pour les sorties asymétriques, ne

connectez pas de câbles aux pôles «-» (voir le Audio Wiring Card d’Extron).

NOTE: The length of exposed wires is critical. The ideal length is 3/16 inch (5 mm).

Tip

Ring

ves Tip

Ring

Balanced Audio Output

Tip

Ring

ves Tip

Ring

Tip

Sleeves

Tip

No Ground Here

Unbalanced Audio Output

Tip

Sleeve

Tip

Sleeve

Unbalanced Audio InputBalanced Audio Input

Page 4

Front Panel Overview

INPUTS

CONFIG

1 2 3 4 5 6 7 8

SIGNAL

HDCP

INPUTS

2 3 4 5 6 7 8 1A 1B 1C

OUTPUTS

ENTER

COM

RTS

eBUS

CTS

LIMIT

1213142314

OVER

IR/S

I/O RELAYS

VOLUME

Figure 2. Front Panel Features, IN1608 xi IPCP SA

Front panel configuration port — Connect a host device to the USB mini-B port for device conguration, control, and

rmware upgrades.

Input selection buttons (1-8) — Press one of these buttons to select an input. The buttons light amber for audio and video,

green for video only, or red for audio only.

Status LED indicators

• Input signal LEDs — Light green for each input when active video content is detected.

• Output signal LEDs — Remain lit green when active video is being output or blink amber when output video and sync

are disabled.

• Input HDCP LEDs — Light green for each input signal that is HDCP-encrypted. Analog inputs 1 and 2 cannot be HDCP-

encrypted.

• Output HDCP LEDs — Light green for an output when it is currently HDCP-encrypted.

Menu and Enter buttons — Press these buttons to access and navigate the on-screen display menu system.

Navigation buttons — Press these buttons to navigate through the on-screen

display menu system or change selected settings.

Volume knob and LED indicators — Rotate the Volume knob to adjust the

program, microphone, or output volume. The eight Volume LED indicators light according to the volume level. The LEDs light in order from bottom to top to indicate steps from 1% (-99 dB) to 99% (-1 dB). The bottom LED blinks when the volume is muted. The top LED blinks when the volume is at 100% (0 dB).

IPCP Pro LED indicators — IPCP Pro models only (see the IPCP Pro Series

Setup Guide for details).

IN1608 xi

SCALING PRESENTATION SWITCHER

IN1608 xi Series Conﬁguration

To congure IN1608 xi scalers, use the front panel controls and the on-screen display (OSD) menu, the internal web pages, PCS, or SIS commands.

On-screen Display (OSD) Menu System

To congure IN1608 xi scalers using the OSD menu, connect a display to either HDMI output or to a DTP/HDBaseT device. The OSD menu consists of nine submenus accessed using the front panel Menu or Enter button (see the example above, right).

NOTE: Press and hold the Enter button for 10 seconds to edit

settings in the Communication submenu.

Internal Web Pages

To congure IN1608 xi scalers using the factory-installed web pages in a web browser (see the example at right), connect the Ethernet port on the device to a LAN or WAN. The default IP address is 192.168.254.254.

Page 5

Extron Product Conﬁguration Software

To congure IN1608 xi scalers using PCS, install the software (available on the Extron website, www.extron.com) to a PC connected to the scaler via Ethernet or front panel USB Cong port. After the installation, start the program. For full instructions, press <F1> on the keyboard or click the ? button in the software and select Help File.

Basic SIS Command Table

To congure IN1608 xi scalers with specic SIS commands via an RS-232, USB, or Ethernet connection, use the Extron DataViewer utility or a control system to send and receive SIS commands. The table below lists a selection of SIS commands. For a full list of SIS commands and variables, see the IN1608 xi Series User Guide at www.extron.com.

Command ASCII Command Response Additional Description

Select audio and video input

Select video input only

Select audio input only

Execute Auto-Image™

Execute Auto-Image and ll

Execute Auto-Image and follow

Mute video to black

Mute video and sync

Unmute video and sync

NOTE: By default, setting the audio mute with the following commands affects all outputs (configurable through group masters).

X!! InX!

X!& InX!

X!$ InX!

1*A

2*A

Img0]

Img1]

Img2]

Vmt1]

Vmt2]

Vmt0]

All] Selects audio and video input X!.

•

RGB] Selects the video only input X!.

•

Aud] Selects the audio only input X!.

•

Executes an Auto-Image on the current input.

Executes an Auto-Image and lls the output.

Executes an Auto-Image and maintains the aspect ratio of the current input.

Mutes the video and displays a black output.

Mutes the video and sync output.

Unmutes the video.

Set master audio mute

View master audio mute status

Enable executive mode 1

Enable executive mode 2

Disable executive modes

Set scaler IP address

Set scaler DHCP mode

Set subnet mask

Set gateway IP address

Reboot network

ED7*X( GRPM} GrpmD07*X(]

ED7GRPM} X(]

Exe1]

Exe2]

Exe0]

EX4) CI} Ipi•X4)]

EX( DH} IdhX(]

EX4! CS} Ips•X4!]

EX4@ CG} Ipg•X4@]

E2BOOT} Boot2]

NOTE: IP settings do not take effect until the E2BOOT} command is executed.

View DTP vs. HDBT Switch Position

EO3HDBT} X6&]

HdbtO3*X6&]

NOTES:

X! = Input selection (1-8) X( = Enable or disable: 0 = off or disabled, 1 = on or enabled) X4) = IP address (nnn.nnn.nnn.nnn), 192.168.254.254 = default) X4! = Subnet mask (nnn.nnn.nnn.nnn), 255.255.255.0 = default) X4@ = Gateway address (nnn.nnn.nnn.nnn), 0.0.0.0 = default) X6& = TP format: 0 = DTP format (default), 1 = HDBaseT format

Enable or disable master audio mute.

View the current master audio mute status.

Locks the entire front panel.

Locks the front panel except for input selection and volume control.

Allows all front panel adjustments and selections.

Species a new scaler IP address.

Enables or disables DHCP (0 = default).

Species a new subnet mask.

Species a new gateway IP address.

Restarts the network connection after IP or DHCP changes.

View the DTP/HDBT mode switch position X6& on output 1C (verbose mode 2/3 response).

Firmware Updates

Download rmware updates from the Extron website and upload them via the internal web pages, PCS, or the Extron Firmware Loader program.

Page 6

Trademarks

All trademarks mentioned in this guide are the properties of their respective owners. The following registered trademarks(

), registered service marks(

), and trademarks(TM) are the property of RGBSystems, Inc. or ExtronElectronics

(see the current list of trademarks on the Terms of Use page at www.extron.com):

Extron, Cable Cubby, ControlScript, CrossPoint, DTP, eBUS, EDID Manager, EDID Minder, Flat Field, FlexOS, Global Configurator, GlobalScripter, GlobalViewer, Hideaway, HyperLane, IPIntercom, IPLink, KeyMinder, LinkLicense, LockIt, MediaLink, MediaPort, NetPA, PlenumVault, PoleVault, PowerCage, PURE3, Quantum, SoundField, SpeedMount, SpeedSwitch, SystemINTEGRATOR, TeamWork, TouchLink, V-Lock, VideoLounge, VN-Matrix, VoiceLift, WallVault, WindoWall, XTP, XTPSystems, and ZipClip

Registered Service Mark

(SM)

: S3 Service Support Solutions

AAP, AFL (Accu-RateFrameLock), ADSP(Advanced Digital Sync Processing), Auto-Image, CableCover, CDRS(ClassD Ripple Suppression), Codec Connect, DDSP(Digital Display Sync Processing), DMI (DynamicMotionInterpolation), DriverConfigurator, DSPConfigurator, DSVP(Digital Sync Validation Processing), eLink, Entwine, EQIP, Everlast, FastBite, FOX, FOXBOX, IP Intercom HelpDesk, MAAP, MicroDigital, Opti-Torque, ProDSP, QS-FPC(QuickSwitch Front Panel Controller), Room Agent, Scope-Trigger, ShareLink, Show Me, SIS, SimpleInstructionSet, Skew-Free, SpeedNav, StudioStation, Triple-Action Switching, True4K, Vector™ 4K , WebShare, XTRA, and ZipCaddy

Extron Headquarters

+800.633.9876 Inside USA/Canada Only

Extron USA - West Extron USA - East

+1.714.491.1500 +1.919.850.1000

+1.714.491.1517 FAX +1.919.850.1001 FAX

Extron Europe

+800.3987.6673

Inside Europe Only

+31.33.453.4040

+31.33.453.4050 FAX

Registered Trademarks (

Trademarks (™

Extron Asia

+65.6383.4400

+65.6383.4664 FAX

Extron Japan

+81.3.3511.7655

+81.3.3511.7656 FAX

)

Extron China

+86.21.3760.1568

+86.21.3760.1566 FAX

Extron Middle East

+971.4.299.1800

+971.4.299.1880 FAX

Extron Australia

+61.8.8113.6800 +61.8.8351.2511 FAX

Extron India

1800.3070.3777

(Inside India Only)

+91.80.3055.3777

+91.80.3055.3737 FAX

68-1916-53 Rev. A

11 17