Page 1
IMPORTANT:
complete user guide
instructions, and specifications.
SR
AB CDGH EFIK
O
IN1608 SA HDBT
Furniture Mounting
Rack Mounting
Go to www.extron.com for the
, installation
IN1608 HDBT Series • Setup Guide
The Extron IN1608 HDBT Scaling Presentation Switcher is an eight input, HDCP-compliant video scaler that accepts a wide variety of audio and
video formats and provides HDMI and HDBaseT video outputs. This guide allows an experienced user to set up and congure IN1608 HDBT,
IN1608 SA HDBT, IN1608 MA 70 HDBT, IN1608 IPCP SA HDBT, and IN1608 IPCP MA 70 HDBT scalers. It covers how to perform basic operations
using the front panel controls and selected Simple Instruction Set (SIS™) commands.
NOTE: For full installation, configuration, menus, connector wiring, and operation details, see the IN1606 and IN1608 Series User Guide at
www.extron.com. For installation, configuration, and operation details of the IPCP Pro 350 control processor, see the IPCP Pro Series
User Guide.
Installation
IN1608 Series Rear Panel Connectors
JL
34G
12RTSCTS
eBUS
+V+S -S G
PWR OUT = 6W
HDBT OUT
LINK
LAN 1
LAN 2 LAN 3
A
HDMI
B
L1R
L2
AMPLIFIED OUTPUT
2x25W(8Ω)/2x50W(4Ω)
L
3
R
L5R
L
L4
R
L6
R
1
12
+48V
R
+48V
MIC/LINE
2
VARIABLE
LR
CLASS 2 WIRING
RESET
100-240V ~ 1.5 A MAX
50/60 Hz
1
CONFIGURABLE
2
IN1608 IPCP SA HDBT
3
HDMI HDMI
4
COM 1 COM 2 COM 3DIGITAL I/O
G
Tx RxGTx RxGTx Rx
IR/SERIAL RELAYS
1
1 2 C 3 4 C
2
R
SG
SG
5
6
7
SIG
LINK SIG
DTP IN
INPUTS OUTPUTSAUDIO INPUTS OUTPUT
RS-232 IR
Tx Rx Tx RxG
OVER DTP
RS-232 IR
Tx Rx Tx RxG
8
LINK SIG
DTP IN
OVER HDBT
RS-232 IR
Tx Rx Tx RxG
C
Power and Input Connections Output Connections Control Connections
AC power connector
A
Configurable analog 15-pin HD (VGA) connectors (inputs 1 and 2)
B
HDMI input connectors (inputs 3 through 6)
C
DTP input and corresponding RS-232/IR Over DTP connectors
D
(inputs 7 and 8)
Analog audio input connectors (associated with inputs 1 through 6)
E
Mic/Line audio input connectors and adjacent phantom power LEDs
F
HDBaseT output connector and
G
corresponding RS-232/IR Over
HDBT connector (output C)
HDMI output connectors
H
(outputs A and B)
Analog audio output connectors
I
Amplified audio output connector
J
(SA and MA models only)
Remote RS-232
K
connector
IPCP Pro 350 control
L
processor (IPCP
models only)
LAN connector
M
(non-IPCP models
only)
Figure 1. IN1608 Series Rear Panel Connectors (IN1608 IPCP SA HDBT Shown)
The IN1608 IPCP HDBT models feature a built-in Extron IPCP Pro 350 control processor for controlling and monitoring a
variety of external devices, such as projectors and lights. See the IPCP Pro Series Setup Guide for more details.
NOTE: The non-IPCP models have a LAN connector next to the Remote RS-232 connector (see M to the
right) instead of the IPCP Pro 350 control processor.
OUTPUTS
12
VARIABLE
LR
AMPLIFIED OUTPUT
2x25W(8Ω)/2x50W(4Ω)
RESET
Mounting and Cabling
R
M
LR
CLASS 2 WIRING
REMOTE
LAN
RS-232
Tx Rx
EMOTE
RS-232
Tx Rx
G
G
Step 1 — Mount the device
a. Turn off or disconnect all equipment power sources.
b. Mount IN1608 HDBT scaler to a rack using the
pre-installed rack ears or use an optional mounting kit
for under-the-desk mounting (see the two images to
the right). The IN1608 HDBT comes in a 1U, full rack
width enclosure. All other IN1608 HDBT models come
in 2U, full rack width enclosures.
Mounting Screws
(2) Places
Each Side
Rack Ears
#8 Screw
(4) Places
Each Side
MBU 149
Mounting Bracket
1
Page 2
IN1608 HDBT Series • Setup Guide (Continued)
12345678
Insert Twisted
Pair Wires
Pins:
Pin
1
2
3
4
5
6
7
8
Wire color
White-green
Green
White-orange
Blue
White-blue
Orange
White-brown
Brown
Wire color
T568A T568B
White-orange
Orange
White-green
Blue
White-blue
Green
White-brown
Brown
Step 2 — Connect inputs
a. Connect analog video sources to the VGA connectors (see gure 1, B on page 1).
b. Connect digital HDMI or DVI (with an appropriate adapter) sources to the HDMI connectors (see gure 1, C).
c. Connect a DTP transmitter to the DTP input connectors (see gure 1, D). For cable wiring and recommendations, see Twisted Pair
Recommendations for DTP and HDBaseT Communication below.
Signal LED — Lights green when the unit is receiving an active video signal from a DTP transmitter.
Link LED — Lights amber when a valid link is established to a DTP transmitter.
d. To pass serial or infrared data, connect the control device to the RS-232 and IR Over DTP captive screw connectors (see RS-232 and IR
Over TP Wiring on page 3).
e. Connect analog audio input sources to the 5-pole captive screw connectors (see gure 1, E). See Audio Wiring on page 3.
f. Connect Mic/Line audio input sources to the 3-pole captive screw connectors (see gure 1, F).
Step 3 — Connect outputs
a. Connect an HDBaseT-compatible device to the HDBT output connector (see gure 1, G). For cable wiring and recommendations, see
Twisted Pair Recommendations for DTP and HDBaseT Communication below.
Signal LED — Lights green when the scaler is outputting active video.
Link LED — Lights amber when a valid link is established between the scaler and HDBaseT sink.
b. To pass serial or infrared data, connect a control device to the RS-232 and IR Over HDBT captive screw connector (see RS-232 and IR
Over TP Wiring on page 3).
c. Connect suitable video displays to the HDMI connectors (see gure 1, H).
d. Connect analog audio output devices to the 3.5 mm, 5-pole captive screw connectors (see gure 1, I). See Audio Wiring on page 3.
e. For SA and MA models, connect an audio output device to the 5 mm, 4-pole or 2-pole captive screw connector (see gure 1, J).
Step 4 — Connect control devices
a. To control non-IPCP models through Ethernet, connect a LAN or WAN to the LAN connector (see M on page 1). For the IPCP models,
connect a LAN or WAN to any of the LAN connectors on the IPCP Pro control processor (see gure 1, L). The default IP address is
192.168.254.254. The default subnet mask is 255.255.0.0.
b. For serial RS-232 control, connect a host device to the 3-pole captive screw connector (see gure 1, K). The default baud rate is 9600.
c. For control through USB, connect a host device to the front panel USB mini-B port (see gure 2, A on page 3).
Step 5 — Set up the IPCP Pro control processor (IPCP models only)
See the IPCP Pro Series Setup Guide for installation details.
Step 6 — Connect power
Connect a 100 to 240 VAC, 50-60 Hz power source to the AC power connector (see gure 1, A).
Twisted Pair Recommendations for DTP and HDBaseT Communication
Extron recommends using the following practices to achieve full transmission distances and reduce
transmission errors:
• Use Extron XTP DTP 24 SF/UTP cable for the best performance. At a minimum, Extron recommends
24 AWG, solid conductor, STP cable with a minimum bandwidth of 400 MHz.
• Terminate cables with shielded connectors to the TIA/EIA-T568B standard (shown to the right).
• Limit the use of more than two pass-through points, which may include patch points, punch down
connectors, couplers, and power injectors. If these pass-through points are required, use shielded
couplers and punch down connectors.
ATTENTION:
• Do not connect these connectors to a computer or telecommunications network.
• Ne connectez pas ces ports à des données informatiques ou à un réseau de télécommunications.
2
• DTP remote power is intended for indoor use only. No part of the network that uses DTP remote power should be routed outdoors.
• L’alimentation DTP à distance est destiné à une utilisation en intérieur seulement. Aucune partie du réseau qui utilise l’alimentation DTP
NOTE: When using shielded twisted pair cable in bundles or conduits, consider the following:
• Do not exceed 40% ll capacity in conduits.
• Do not comb the cable for the rst 20 meters, where cables are straightened, aligned, and secured in tight bundles.
• Loosely place cables and limit the use of tie wraps or hook-and-loop fasteners.
• Separate twisted pair cables from AC power cables.
à distance ne peut être routée en extérieur.
TIA/EIA-T568B
Pin Wire Color
1 White-orange
2 Orange
3 White-green
4 Blue
5 White-blue
6 Green
7 White-brown
8 Brown
Page 3
RS-232 and IR Over TP Wiring
AB CDEF
Slee
No Ground Here
Slee
Do not tin the wires!
To pass bidirectional serial command signals between DTP or HDBaseT-compatible devices, connect a control device to the three leftmost poles
(Tx, Rx, and G) of the 5-pole captive screw connector. To transmit and receive IR signals, connect a control device to the three rightmost poles
(G, Tx, and Rx).
NOTE: RS-232 and IR data can be transmitted or received simultaneously. The ground pole is shared by both ports.
Audio Wiring
Wire the audio input and output connectors as shown below and to the right. Use the supplied tie wrap to strap the audio cable to the extended
tail of the connector. This does not apply to the amplied audio output connector on the SA and MA models.
ATTENTION: For unbalanced outputs, do not connect
wires to the “-” poles (see the Extron Audio Wiring Card).
ATTENTION : Pour les sorties asymétriques, ne connectez
pas de câbles aux pôles «-» (voir le Audio Wiring Card
d’Extron).
NOTE: The length of exposed wires is critical. The ideal
length is 3/16 inch (5 mm).
Front Panel Overview
Tip
Ring
ves
Tip
Ring
Balanced Audio Output
Tip
Ring
ves
Tip
Ring
LR
Tip
Sleeves
Tip
No Ground Here
Unbalanced Audio Output
LR
Tip
Sleeve
Tip
Sleeve
Unbalanced Audio InputBalanced Audio Input
LR
LR
G
COM
RTS
eBUS
CTS
LIMIT
S
Tx
Rx
1213142314
23
OVER
OUTPUTS
MENU
ENTER
SCALING PRESENTATION SWITCHER
CONFIG
Extron
INPUTS
1 2 3 4 5 6 7 8
INPUTS
SIGNAL
1
2 3 4 5 6 7 8 A B C
HDCP
IR/S
I/O RELAYS
VOLUME
2
IN1608
Figure 2. Front Panel Features (IN1608 IPCP SA HDBT Shown)
Front panel configuration port — Connect a host device to the USB mini-B port for device conguration, control, and rmware upgrades.
A
Input selection buttons (1-8) — Press one of these buttons to select an input. The buttons light amber for audio and video, green for video
B
only, or red for audio only.
Status LED indicators
C
Input signal LEDs — Light green for each input when active video content is detected.
Output signal LEDs — Remain lit green when active video is being output or blink amber when output video and sync are disabled.
Input HDCP LEDs — Light green for each input signal that is HDCP-encrypted. Analog inputs 1 and 2 cannot be HDCP-encrypted.
Output HDCP LEDs — Light green for an output when it is currently HDCP-encrypted.
Menu and Enter buttons — Press these buttons to access and navigate the on-screen display menu system.
D
Navigation buttons — Press these buttons to navigate through the on-screen display menu system or change selected settings.
E
Volume knob and LED indicators — Rotate the Volume knob to adjust the program volume
F
(default). The eight Volume LED indicators light according to the volume level. The LEDs light in
order from bottom to top to indicate steps from 1% (-99 dB) to 99% (-1 dB). The bottom LED
blinks when the volume is muted. The top LED blinks when the volume is 100% (0 dB).
IPCP Pro 350 LED indicators — See the IPCP Pro Series Setup Guide for details.
G
IN1608 HDBT Series Configuration
To congure IN1608 HDBT scalers, use the front panel controls and the on-screen display (OSD)
menu, the internal Web pages, the Extron Product Conguration Software, or SIS commands.
On-screen Display (OSD) Menu System
To congure IN1608 HDBT scalers using the OSD menu, connect a display to either HDMI output or
to an HDBaseT-enabled device through the HDBT output connector. The OSD menu consists of nine
submenus accessed using the front panel Menu or Enter button (see the example to the right).
NOTE: Press and hold the Enter button for 10 seconds to edit settings in the
Communication submenu.
3
Page 4
Internal Web Pages
To congure IN1608 HDBT scalers using the factory-installed Web pages in a Web
browser (see the example to the right), connect the Ethernet port on the device to
a LAN or WAN. The default IP address is 192.168.254.254.
Extron Product Configuration Software
To congure IN1608 HDBT scalers using the Extron Product Conguration
Software (PCS), install the software (available on the Extron website,
www.extron.com) to a PC connected to the scaler via Ethernet or front panel USB
Cong port. After the installation, start the program. For full instructions, press
<F1> on the keyboard or click the ? button in the software and select Help File.
Basic SIS Command Table
To congure IN1608 HDBT scalers with specic SIS commands via an RS-232,
USB, or Ethernet connection, use the Extron DataViewer utility or a control system
to send and receive SIS commands. The table below lists a selection of SIS commands. For a full list of SIS commands and variables, see the
IN1606 and IN1608 Series User Guide at www.extron.com.
Command ASCII Command
Select audio and video input
Select video input only
Select audio input only
Execute Auto-Image™
Execute Auto-Image and ll
Execute Auto-Image and follow
Mute video to black
Mute video and sync
Unmute video and sync
(Host to Device)
X! ! InX!
X!& InX!
X!$ InX!
A
1*A
2*A
1B
2B
0B
Response
(Device to Host)
All] Selects audio and video input X!.
•
RGB] Selects the video only input X!.
•
Aud] Selects the audio only input X!.
•
Img0
]
Img1
]
Img2
]
Vmt1
]
Vmt2
]
Vmt0
]
Additional Description
Executes an Auto-Image on the current input.
Executes an Auto-Image and lls the output.
Executes an Auto-Image and maintains the aspect ratio of
the current input.
Mutes the video and displays a black output.
Mutes the video and sync output.
Unmutes the video.
NOTE: By default, setting the audio mute with the following commands affects all outputs (configurable through group masters).
Set master audio mute
View master audio mute status
Enable executive mode 1
Enable executive mode 2
Disable executive modes
Set scaler IP address
Set scaler DHCP mode
Set subnet mask
Set gateway IP address
Reboot network
ED7*X( GRPM} GrpmD07*X(]
ED7GRPM} X( ]
1X
2X
0X
EX4) CI} Ipi
Exe1
Exe2
Exe0
]
]
]
X4) ]
•
EX( DH} IdhX(]
EX4! CS} Ips
EX4@ CG} Ipg
X4! ]
•
X4@ ]
•
E2BOOT} Boot2]
Enable or disable master audio mute.
View the current master audio mute status.
Locks the entire front panel.
Locks the front panel except for input selection and volume
control.
Allows all front panel adjustments and selections.
Species a new scaler IP address.
Enables or disables DHCP (0 = default).
Species a new subnet mask.
Species a new gateway IP address.
Restarts the network connection after IP or DHCP changes.
NOTE: IP settings will not take effect until the E 2BOOT} command is executed.
NOTES:
X! = Input selection (1-8)
X( = Enable or disable (0 = off or disabled; 1 = on or enabled)
X4) = IP address (xxx.xxx.xxx.xxx; 192.168.254.254 = default)
X4! = Subnet mask (xxx.xxx.xxx.xxx; 255.255.0.0 = default)
X4@ = Gateway address (xxx.xxx.xxx.xxx; 0.0.0.0 = default)
Firmware Updates
Download rmware updates from the Extron website and upload them via the internal Web pages or the Extron Firmware Loader program.
Extron USA Headquarters
+1.800.633.9876 (Inside USA/Canada Only)
4
© 2015 Extron Electronics — All rights reserved. All trademarks mentioned are the property of their respective owners. www.extron.com
Extron USA - West: +1.714.491.1500 FAX: +1.714.491.1517
Extron USA - East: +1.919.850.1000 FAX: +1.919.850.1001
68-1916-52 Rev. A
06 15
Loading...