Extron Electronics ICWK iMAC Kit User Manual

Figure 3a

Installation

Installation Guide

ICWK cable
exit point

ICWK 9-pin
connector

Page 3

Figure 3b

EXTRON ELECTRONICS

1230 South Lewis Street
Anaheim, CA 92805
[phone] FAX (714) 491­1517

U.S.A.

EXTRON ELECTRONICS, EUROPE

Beeldschermweg 6C
3821 AH Amersfoort
[phone] FAX [phone]

The Netherlands

Connector panel cover

ICWK cable coiled inside

EXTRON ELECTRONICS, ASIA

41B Kreta Ayer Road
Singapore 089003
[phone] FAX [phone]

Singapore

Written/Printed

in the USA

89-10

68-406-01

Rev. A

ICWK iM

AC

Kit

P/N 70-076-01

Installation

ICWK iMACTM Installation

The Extron ICWK iMAC when installed in an iMAC computer enables an Extron
interface to be connected to the iM
connected to the interface to display the image seen on the iMAC monitor.

AC. A projector or monitor may then be

Installation

The following Extron universal interfaces are compatible with the ICWK iM

AC.

RGB 118 Plus RGB 120 RGB 124
RGB 202xi RGB 302, 304 RGB 440

The ICWK iM

AC kit consists of the following two items.

68-406-01 ICWK iMAC Installation Guide
70-076-01 ICWK iMAC

Installing the ICWK iMac Kit

1. Power the iMAC OFF.

2. Disconnect all iMAC cables including the power cord.

3. Turn the iMAC upside down so that it sits on its top (use a soft pad to avoid
scratching the case), with the screen away from you as shown in Figure 2a.

NOTE: The iMAC must be upside down during the installation of the ICWK iMAC

kit and in this position it is unstable due to the shape of the case. Be sure
that it is securely positioned to avoid possible damage.

4. Loosen the bottom cover screw (Figure 2a) and remove the cover.

5. Create a quarter inch diameter notch in the bottom cover as shown in Figure
2b using a round file or other suitable tool.

6. Remove the iM
into the ICWK T 15-pin D sub female connector.

7. Plug the ICWK T 15-pin D sub male connector into the iMac computer video
output connector 15-pin D sub female connector. The ICWK cable/circuit
card must be routed under the iMAC monitor cable to allow the bottom cover
to fit properly.

AC monitor cable connector identified in Figure 2c and plug it

Figure 2a

iMAC computer video output
connector (15-pin D sub)

Cover screw

Figure 2c

Notch for ICWK
cable exit point

Figure 2b

iMAC monitor
connector

ICWK T connector

8. Reinstall the iMAC bottom panel with the ICWK cable positioned through the
notch (Figure 3a) created in step 5 and the heat shrink insulated ICWK circuit
card positioned as far under the iMAC monitor connector as possible. A piece
of tape may prove helpful for holding a stubborn ICWK circuit card in place.
Carefully snap the bottom cover in place, when correctly positioned, tighten
the cover screw.

9. Turn the iMAC right side up and reconnect the cables removed in step 2. The
ICWK 9-pin connector/cable may be coiled and stored inside the connector
panel cover as shown in Figure 3b.

10.Power the iM

Page 1 Page 2

AC ON and verify proper operation.

Extron • ICWK iMAC Kit • Installation Guide

Figure 2d

Extron • ICWK iMAC Kit • Installation Guide

ICWK T connector

Figure 2e

ICWK circuit card